Carbon nanotube/graphene oxide‐added CaO‐B2O3‐SiO2 glass/Al2O3 composite as substrate for chip‐type supercapacitor

A CaO‐B₂O₃‐SiO₂ (CBS) glass/40 wt% Al₂O₃ composite sintered at 900°C exhibited a dense microstructure with a low porosity of 0.21%. This composite contained Al₂O₃ and anorthite phases, but pure glass sintered at 900°C has small quantities of wollastonite and diopside phases. This composite was measured to have a high bending strength of 323 MPa and thermal conductivity of 3.75 W/(mK). The thermal conductivity increased when the composite was annealed at 850°C after sintering at 900°C, because of the increase in the amount of the anorthite phase. 0.25 wt% graphene oxide and 0.75 wt% multi‐wall carbon nanotubes were added to the CBS/40 wt% Al₂O₃ composite to further enhance the thermal conductivity and bending strength. The specimen sintered at 900°C and subsequently annealed at 850°C exhibited a large bending strength of 420 MPa and thermal conductivity of 5.51 W/(mK), indicating that it would be a highly effective substrate for a chip‐type supercapacitor.     

Degradation of Nextel™ 610‐based oxide‐oxide ceramic composites by aluminum oxychloride decomposition products

Nextel? 610 alumina fibers and alumina‐YAG (yttrium‐aluminum garnet) matrices were used to make oxide‐oxide ceramic matrix composites (CMCs) with and without monazite (LaPO₄) fiber‐matrix interfaces. Twelve sequential aluminum oxychloride (AlOCl) infiltrations with 1 hour heat treatments at 1100°C and a final 1 hour heat treatment at 1200°C were used for matrix densification. This matrix processing sequence severely degraded CMC mechanical properties. CMC tensile strengths and interlaminar tensile (ILT) strengths were less than 10 MPa and 1 MPa, respectively. Axial fracture of Nextel? 610 fibers was observed after ILT testing, highlighting the extreme degradation of fiber strength. Extensive characterization was done to attempt to determine the responsible degradation mechanisms. Changes in Nextel? 610 fiber microstructure after CMC processing were characterized by optical microscopy, SEM, and extensively by TEM. In AlOCl degraded fibers, grain boundaries near the fiber surface were wetted with a glass that contained Y₂O₃/SiO₂ or Y₂O₃/La₂O₃/P₂O₅/SiO₂, and near‐surface pores were partially filled with Al₂O₃. This glass must also contain some Al₂O₃ and initially some chlorine. AlOCl decomposition products were predicted using the FactSage^® Thermochemical code, and were characterized by mass spectrometry. Effects of AlOCl precursors on monazite coated and uncoated Nextel? 610 fibers tow and filament strength were evaluated. A mechanism for the severe degradation of the oxide‐oxide CMCs and Nextel? 610 fibers that involves subcritical crack growth promoted by release of chlorine containing species during breakdown of intergranular glasses in an anhydrous environment is proposed.     

Co‐doped ZnO thin films grown by pulsed electron beam ablation as model nano‐catalysts in fischer‐tropsch synthesis

A single‐step deposition of cobalt‐doped zinc oxide (Co‐ZnO) thin film nano‐composites on three different crystalline substrates, viz., Al₂O₃ (c‐sapphire), silicon (100) (Si), and SiO₂ (quartz) is reported, using pulsed electron beam ablation (PEBA). The results indicate that the type of substrate has no effect on Co‐ZnO films stoichiometry, morphology, microstructure, and film thickness. The findings show the presence of hexagonal close‐packed metallic Co whose content increases in the films deposited on Al₂O₃ and Si substrates relatively to SiO₂ substrate. The potential of the films as model nano‐catalysts has been evaluated in the context of the Fischer‐Tropsch (FT) process. Fuel fractions, which have been observed in FT liquid products, are rich in diesel and waxes. Specifically, Co‐ZnO/Al₂O₃ nano‐catalyst shows a selectivity of ～4%, 31%, and 65% towards gasoline, diesel, and waxes, respectively, while Co‐ZnO/SiO₂ nano‐catalyst shows a selectivity of ～12%, 51%, and 37%, for gasoline, diesel, and waxes, respectively. © 2018 American Institute of Chemical Engineers AIChE J, 64: 3332–3340, 2018     

Simultaneously enhanced mechanical properties and thermal properties of ultrahigh‐molecular‐weight polyethylene with polydopamine‐coated α‐alumina platelets

Polydopamine (PDA) was employed to modify micrometric Al₂O₃ platelets to improve the interfacial compatibility between α‐Al₂O₃ powder and ultrahigh‐molecular‐weight polyethylene (UHMWPE). The structure of PDA‐coated Al₂O₃ and UHMWPE composites was investigated via Fourier transform infrared spectroscopy, scanning electron microscopy and X‐ray photoelectron spectroscopy. The thermal stability and mechanical performance of the samples were also evaluated. It is clear that UHMWPE/PDA‐Al₂O₃ composites exhibit better mechanical properties, higher thermal stability and higher thermal conductivity than UHMWPE/Al₂O₃ composites, owing to the good dispersion of Al₂O₃ powder in the UHMWPE matrix and the strong interfacial force between the macromolecules and the inorganic filler caused by the presence of PDA. The tensile strength and the tensile elongation at break of UHMWPE/PDA‐Al₂O₃ composite with 1 wt% PDA‐Al₂O₃ are 62.508 MPa and 462%, which are 1.96 and 1.98 times higher than those of pure UHMWPE, respectively. The thermal conductivity of UHMWPE/PDA‐Al₂O₃ composite increases from 0.38 to 0.52 W m^?1 K^?1 with an increase in the dosage of PDA‐Al₂O₃ to 20 wt%. The results show that the prepared PDA‐coated Al₂O₃ powder can simultaneously enhance the mechanical properties and thermal conductivity of UHMWPE. © 2018 Society of Chemical Industry     

Effective thermal conductivity and thermal properties of phthalonitrile‐terminated poly(arylene ether nitriles) composites with hybrid functionalized alumina

A polymer‐based thermal conductive composite has been developed. It is based on a dispersion of micro‐ and nanosized alumina (Al₂O₃) in the phthalonitrile‐terminated poly (arylene ether nitriles) (PEN‐t‐ph) via solution casting method. The Al₂O₃ with different particle sizes were functionalized with phthalocyanine (Pc) which was used as coupling agent to improve the compatibility of Al₂O₃ and PEN‐t‐ph matrix. The content of microsized functionalized Al₂O₃ (m‐f‐Al₂O₃) maintained at 30 wt % to form the main thermally conductive path in the composites, and the nanosized functionalized Al₂O₃ (n‐f‐Al₂O₃) act as connection role to provide additional channels for the heat flow. The thermal conductivity of the f‐Al₂O₃/PEN‐t‐ph composites were investigated as a function of n‐f‐Al₂O₃ loading. Also, a remarkable improvement of the thermal conductivity from 0.206 to 0.467 W/mK was achieved at 30 wt % n‐f‐Al₂O₃ loading, which is nearly 2.7‐fold higher than that of pure PEN‐t‐ph polymer. Furthermore, the mechanical testing reveals that the tensile strength increased from 99 MPa for pure PEN‐t‐ph to 105 MPa for composites with 30 wt % m‐f‐Al₂O₃ filler loading. In addition, the PEN‐t‐ph composites possess excellent thermal properties with glass transition temperature (T_g) above 184°C, and initial degradation temperature (T_id) over 490°C. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41595.     

Microstructured Al‐fiber@meso‐Al2O3@Fe‐Mn‐K Fischer–Tropsch catalyst for lower olefins

A thin‐sheet Al‐fiber@meso‐Al₂O₃@Fe‐Mn‐K catalyst is developed for the mass/heat‐transfer limited Fischer–Tropsch synthesis to lower olefins (FTO), delivering a high iron time yield of 206.9 µmol_CO s^?1 at 90% CO conversion with 40% selectivity to C₂‐C₄ olefins under optimal reaction conditions (350°C, 4.0 MPa, 10,000 mL/(g·h)). A microfibrous structure consisting of 10 vol % 60‐µm Al‐fiber and 90 vol % voidage undergoes a steam‐only‐oxidation and calcination to create 0.6 µm mesoporous γ‐Al₂O₃ shell along with the Al‐fiber core. Active components of Fe and Mn as well as additives (K, Mg, or Zr) are then placed into the pore surface of γ‐Al₂O₃ shell of the Al‐fiber@meso‐Al₂O₃ composite by incipient wetness impregnation method. Neither Mg‐modified nor Zr‐modified structured catalyst yields better FTO results than K‐modified one, because of their lower reducibility, poorer carbonization property, and fewer basicity. The favorable heat/mass‐transfer characteristics of this new approach are also discussed. © 2015 American Institute of Chemical Engineers AIChE J, 62: 742–752, 2016     

Structure and properties of Al2O3-bonded porous fibrous YSZ ceramics fabricated by aqueous gel-casting

To meet requirements for high porosity and high strength, novel aqueous gel-casting process has been successfully developed to fabricate Al₂O₃-bonded porous fibrous YSZ ceramics with ρ-Al₂O₃ and YSZ fibers as raw materials. Microstructure, phase composition, apparent porosity, bulk density, thermal conductivity, and compressive strength of fabricated porous ceramics were investigated, and effects of fiber content on properties were discussed. According to results, bird nest 3D mesh with interlaced YSZ fibers and Al₂O₃ binder was formed, ensuring the ability to obtain high performance, lightweight ceramics. An increase in the number of YSZ fibers led to more complex interlaced arrangement of fibers and denser network structure of porous ceramics at retaining their stability. Furthermore, their apparent porosity and bulk density increased, whereas thermal conductivity and compressive strength decreased with increasing the fiber content. In particular, comparatively high porosity (71.1–72.7%), low thermal conductivity (0.209–0.503 W/mK), and relatively high compressive strength (3.45–4.24 MPa) were obtained for as-prepared porous ceramics, making them promising for applications in filters, thermal insulation materials, and separation membranes.     

Porous YSZ Ceramics Reinforced by Different Kinds of Fibers

Porous YSZ ceramics reinforced by different fibers were prepared by gel‐casting with 15% solid content and pressureless sintering. The four kinds of fibers (mullite, aluminosilicate, Al₂O₃, and YSZ fibers) were added into the YSZ ceramics with the same 10% vol content. After sintered at 1500°C for 2 h, aluminosilicate and mullite fibers could not be found in the samples of porous YSZ ceramics, which showed they reacted with YSZ ceramics at high temperature, while YSZ and Al₂O₃ fibers still kept perfect after sintering. Furthermore, the influences of fiber content, sintering temperature, porosity of matrix materials on compressive strength and porosity of the porous YSZ ceramics were studied. The results showed that Al₂O₃ fiber showed more obvious reinforcing effect than YSZ fiber on porous YSZ ceramics. The fiber‐reinforcing effects depend on fiber content, sintering temperature, and porosity of matrix materials. The fiber addition can improve the shrinkage behavior of porous ceramics during sintering and strengthen the skeleton of porous ceramics.     

High tensile strength fiber of poly[(R)‐3‐hydroxybutyrate‐co‐(R)‐3‐hydroxyhexanoate] processed by two‐step drawing with intermediate annealing

High tensile strength fibers of poly[(R)‐3‐hydroxybutyrate‐co‐(R)‐3‐hydroxyhexanoate] [P(3HB‐co‐3HH)], a type of microbial polyesters, were processed by one‐step and two‐step cold‐drawn method with intermediate annealing. Thermal degradation behaviors were characterized by differential scanning calorimeter and gel permeation chromatography measurements. Thermal analyses were revealed that molecular weights decreased drastically within melting time at a few minute. One‐step cold‐drawn fiber with drawing ratio of 10 showed tensile strength of 281 MPa, while tensile strength of as‐spun fiber was 78 MPa. When two‐step drawing was applied for P(3HB‐co‐3HH) fibers, the tensile strength was led to 420 MPa. Furthermore, the optimization of intermediate annealing condition leads to enhance the tensile strength at 552 MPa of P(3HB‐co‐3HH) fiber. Wide‐angel X‐ray diffraction measurements of these fibers suggest that the fibers with high tensile strength include much amount of the planer‐zigzag conformation (β‐form) as molecular conformation together with 2₁ helix conformation (α‐form). © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41258.     

Injection‐molded high‐density polyethylene–hydroxyapatite–aluminum oxide hybrid composites for hard‐tissue replacement: Mechanical,biological, and protein adsorption behavior

In this article, we report the mechanical and biocompatibility properties of injection‐molded high‐density polyethylene (HDPE) composites reinforced with 40 wt % ceramic filler [hydroxyapatite (HA) and/or Al₂O₃] and 2 wt % titanate as a coupling agent. The mechanical property measurements revealed that a combination of a maximum tensile strength of 18.7 MPa and a maximum tensile modulus of about 855 MPa could be achieved with the injection‐molded HDPE–20 wt % HA–20 wt % Al₂O₃ composites. For the same composite composition, the maximum compression strength was determined to be 71.6 MPa and the compression modulus was about 660 MPa. The fractrography study revealed the uniform distribution of ceramic fillers in the semicrystalline HDPE matrix. The cytocompatibility study with osteoblast‐like SaOS2 cells confirmed extensive cell adhesion and proliferation on the injection‐molded HDPE–20 wt % HA–20 wt % Al₂O₃ composites. The cell viability analysis with the 3(4,5‐dimethylthiazol‐2‐yl)‐2,5‐diphenyltetrazolium bromide assay revealed a statistically significant difference between the injection‐molded HDPE–20 wt % HA–20 wt % Al₂O₃ composites and sintered HA for various culture durations of upto 7 days. The difference in cytocompatibility properties among the biocomposites is explained in terms of the difference in the protein absorption behavior. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Nano‐engineered nickel catalysts supported on 4‐channel α‐Al2O3 hollow fibers for dry reforming of methane

A nickel (Ni) nanoparticle catalyst, supported on 4‐channel α‐Al₂O₃ hollow fibers, was synthesized by atomic layer deposition (ALD). Highly dispersed Ni nanoparticles were successfully deposited on the outside surfaces and the inside porous structures of hollow fibers. The catalyst was employed to catalyze the dry reforming of methane (DRM) reaction and showed a methane reforming rate of 2040 Lh^?1gNi^?1 at 800°C. NiAl₂O₄ spinel was formed when Ni nanoparticles were deposited on alpha‐alumina substrates by ALD, which enhanced the Ni‐support interaction. Different cycles (two, five, and ten) of Al₂O₃ ALD films were applied on the Ni/hollow fiber catalysts to further improve the interaction between the Ni nanoparticles and the hollow fiber support. Both the catalyst activity and stability were improved with the deposition of Al₂O₃ ALD films. Among the Al₂O₃ ALD coated catalysts, the catalyst with five cycles of Al₂O₃ ALD showed the best performance. © 2018 American Institute of Chemical Engineers AIChE J, 64: 2625–2631, 2018     

Effect of substituting CaO with BaO on the viscosity and structure of CaO‐BaO‐SiO2‐MgO‐Al2O3 slags

In this study, the effect of CaO and BaO substitution on the viscosity and structure of CaO‐BaO‐SiO₂‐MgO‐Al₂O₃ slags was investigated. The results showed that the viscosity increased with an increase in the BaO substitution concentration, which was correlated to an increase in the degree of polymerization (DOP) of the slag structural units as the activation energy increased from 207.9 to 263.8 kJ/mol for viscous flow. Deconvolution and area integration of the Raman spectrum of the slag revealed that the ratio of Q³/Q² (Qⁱ, i is the number of O⁰ in a [SiO₄]‐tetrahedral unit) increased and NBO/Si (nonbridging oxygen per unit silicon atom) decreased with higher BaO content. It was also observed from the ²⁷Al magic angles pinning nuclear magnetic resonance (²⁷Al MAS‐NMR) spectrum that the relative proportion of Al^IV increased, while that of Al^V decreased because of the decrease in the percentage of nonbridging oxygen (O^?), indicating the polymerization of the slag. O_1s X‐ray photoelectron spectroscopy (XPS) was also carried out to semi‐quantitatively analyze the various types of oxygen anions present in the slag. The XPS results correlated well with the results obtained from the analysis of the Raman and ²⁷Al MAS‐NMR spectra of the slags and its viscous behavior.     

Thermal Reaction of Cristobalite in Nano‐SiO2/α‐Al2O3 Powder Systems for Mullite Synthesis

Nanoscaled cristobalite and α‐Al₂O₃ powders were used as the starting materials for synthesizing mullite by solid‐state reaction. The thermal reaction of the cristobalite with α‐Al₂O₃ during the thermal treatment was examined. Cristobalite powder with a D₅₀ value of 430 nm was adopted to mix with α‐Al₂O₃ powders with a D₅₀ values of 230, 310, and 400 nm in a stoichiometric composition of 3Al₂O₃?2SiO₂ (71.8 wt% α‐Al₂O₃ and 28.2 wt% SiO₂). Samples for thermal reaction were prepared using uniaxial pressed from the three mixtures that showed various particle number ratios of SiO₂/Al₂O₃ due to the different particle sizes of α‐Al₂O_3. Examinations were performed by differential thermal analysis, X‐ray diffraction, scanning electron microscopy, energy‐dispersive X‐ray spectroscopy, and transmission electron microscopy techniques. The results showed that cristobalite particles amorphized during the thermal treatment, and then reacted with the α‐Al₂O₃ particle to form mullite via nucleation and growth. The amorphization temperature can be reduced by using finer‐sized α‐Al₂O₃ powders, thus leading to a lower temperature for mullite formation. Mullite crystals with a multidomain structure were observed in the α‐Al₂O₃ particle matrixes. The crystal orientation of the mullite was controlled by the α‐Al₂O₃ matrix, that is, [001] α‐Al₂O₃ → [001] mullite. These results indicate that the amorphization of cristobalite may trigger the reaction of SiO₂ with α‐Al₂O₃, initiating the nucleation of mullite. The α‐Al₂O₃ particles act as the hosts for mullite formation and determine the size of the mullite particles.     

Preparation of Nitrogen‐Doped Mullite Fiber by Nitridation of Silica–Alumina Gel Fiber in Ammonia

Nitrogen‐doped mullite fibers were first synthesized through the nitridation of Al₂O₃–SiO₂ gel fibers in NH₃. The results showed that nitrogen take‐up began at 800°C, reached the maximum at 900°C, and then decreased with increasing temperature. The ceramic fibers nitridated at 900°C were essentially amorphous, but contained a small amount of nano‐sized Al–Si spinel crystals. Mullite was formed after nitridation at 1200°C, accompanied by crystallization of χ‐SiAlON and δ‐Al₂O₃. The incorporation of nitrogen resulted in the formation of a variety of nitrogen‐containing crystalline phases. The grain size of the mullite fibers can be adjusted by changing of the nitrogen content.     

In situ crystallization and elastic properties of transparent MgO–Al2O3–SiO2 glass‐ceramic

Glass‐ceramics (GC) generally possess enhanced mechanical properties compared to their parent glasses. The knowledge of how crystallization evolves and affects the mechanical properties with increasing temperature is essential to optimize the design of the crystallization cycle. In this study, we crystallized a glass of the MgO–Al₂O₃–SiO₂ system with nucleating agents TiO₂ and ZrO₂. The crystallization cycle comprised a 48 hour nucleation treatment at the glass‐transition temperature followed by a 10 hour growth step at a higher temperature. During this cycle, the evolution of crystalline phases was followed by high‐temperature X‐ray diffraction (HTXRD), which revealed the presence of karooite (MgO·2TiO₂), spinel (MgO·Al₂O₃), rutile (TiO₂), sillimanite (Al₂O₃·SiO₂), and sapphirine (4MgO·5Al₂O₃·2SiO₂). The same heat treatment was applied for in situ measurement of elastic properties: elastic modulus, E, shear modulus, G, and Poisson's ratio, ν. The evolution of these parameters during the heating path from room temperature to the final crystallization temperature and during the nucleation and the crystallization plateaus is discussed. E and G evolve significantly in the first two hours of the growth step. At the end of the crystallization process, the elastic and shear moduli of the GC were approximately 20% larger than those of the parent glass.     

Bio‐composites for structural applications: Poly‐l‐lactide reinforced with long sisal fiber bundles

Fully bio‐based and biodegradable composites were compression molded from unidirectionally aligned sisal fiber bundles and a polylactide polymer matrix (PLLA). Caustic soda treatment was employed to modify the strength of sisal fibers and to improve fiber to matrix adhesion. Mechanical properties of PLLA/sisal fiber composites improved with caustic soda treatment: the mean flexural strength and modulus increased from 279 MPa and 19.4 GPa respectively to 286 MPa and 22 GPa at a fiber volume fraction of V_f = 0.6. The glass transition temperature decreased with increasing fiber content in composites reinforced with untreated sisal fibers due to interfacial friction. The damping at the caustic soda‐treated fibers‐PLLA interface was reduced due to the presence of transcrystalline morphology at the fiber to matrix interface. It was demonstrated that high strength, high modulus sisal‐PLLA composites can be produced with effective stress transfer at well‐bonded fiber to matrix interfaces. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40999.     

Ultradrawing properties of ultrahigh‐ molecular‐weight polyethylene/carbon nanotube fibers prepared at various formation temperatures

The influence of formation temperature on the ultradrawing properties of ultrahigh‐molecular‐weight polyethylene/carbon nanotube (UHMWPE/CNT) fiber specimens is investigated. Gel solutions of UHMWPE/CNT with various CNT contents were gel‐spun at the optimum concentration and temperature but were cooled at varying formation temperatures in order to improve the ultradrawing and tensile properties of the UHMWPE/CNT composite fibers. The achievable draw ratio (D_ra) values of UHMWPE/CNT as‐prepared fibers reach a maximum when they are prepared with the optimum CNT content and formation temperature. The D_ra value of UHMWPE/CNT as‐prepared fibers produced using the optimum CNT content and formation temperature is about 33% higher than that of UHMWPE as‐prepared fibers produced using the optimum concentration and formation temperature. The percentage crystallinity (W_c) and melting temperature (T_m) of UHMWPE/CNT as‐prepared fiber specimens increase significantly as the formation temperature increases. In contrast, W_c increases but T_m decreases significantly as the CNT content increases. Dynamic mechanical analysis of UHMWPE and UHMWPE/CNT fiber specimens exhibits particularly high α‐transition and low β‐transition, wherein the peak temperatures of α‐transition and β‐transition increase dramatically as the formation temperature increases and/or CNT content decreases. In order to understand these interesting drawing, thermal and dynamic mechanical properties of the UHMWPE and UHMWPE/CNT as‐prepared fiber specimens, birefringence, morphological and tensile studies of as‐prepared and drawn fibers were carried out. Possible mechanisms accounting for these interesting properties are proposed. Copyright © 2010 Society of Chemical Industry     

Thermal‐Shock Fracture and Damage Resistance Improved by Whisker Reinforcement in Alumina Matrix Composite

Fracture resistance of SiC‐whiskers‐reinforced Al₂O₃‐matrix composite under thermal shock was examined. Equibiaxial tensile thermal stress in the composite was significantly reduced before fracture, because the whiskers made percolation paths that increase heat flux and thereby reduced the temperature gradient. The thermal‐shock fracture resistance (R′) of the composite is thus much higher than that of monolithic Al₂O₃. Thermal‐shock damage resistance (R″″) was estimated from the thermal‐shock stress when a surface crack propagates. R″″ of the composite is also much higher than that of monolithic Al₂O₃ owing to an increment of work‐of‐fracture due to crack‐face bridging of the whiskers.     

Tribological properties of ethylene–propylene–diene rubber + polypropylene + thermal‐shock‐resistant ceramic composites

This work is part of a program on composites used in thermoelectric devices. Tribological properties of dynamic vulcanizate blends of polypropylene and ethylene‐propylene‐diene rubber filled with 5 wt% of microscale powder have been studied. The microscale thermal‐shock‐resistant ceramic filler contains α‐Al₂O₃, mullite (3Al₂O₃ · 2SiO₂ or 2Al₂O₃SiO₂), β‐spodumene glass‐ceramic and aluminium titanate. We found that our ceramic particles are abrasive; they cause strong abrasion of softer steel ball surfaces during dry sliding friction. To overcome the difficulty of particle dispersion and adhesion, the filler was modified through grafting using three types of organic molecules. Dry sliding friction was measured using four types of counter‐surfaces: tungsten carbide, Si₃N₂, 302 steel and 440 steel. Thermoplastic vulcanizate filled with neat ceramic powder shows the lowest friction compared to composites containing the same but surface‐treated powder. We introduce a ‘bump’ model to explain the tribological responses of our composites. ‘Naked’ or untreated ceramic particles protrude from the polymer surface and cause a decrease of the contact area compared to neat polymer. The ball partner surface has only a small contact area with the bumps. As contact surface area decreases, so does friction and the amount of heat generated during sliding friction testing. Chemical coupling of the ceramic to the matrix smoothens the bumps and increases the contact surface, giving a parallel increase in friction. Copyright © 2012 Society of Chemical Industry     

A multiscale methodology quantifying the sintering temperature‐dependent mechanical properties of oxide matrix composites

A novel methodology combining multiscale mechanical testing and finite element modeling is proposed to quantify the sintering temperature‐dependent mechanical properties of oxide matrix composites, like aluminosilicate (AS) fiber reinforced Al₂O₃ matrix (AS_f/Al₂O₃) composite in this work. The results showed a high‐temperature sensitivity in the modulus/strength of AS fiber and Al₂O₃ matrix due to their phase transitions at 1200°C, as revealed by instrumented nanoindentation technique. The interfacial strength, as measured by a novel fiber push‐in technique, was also temperature‐dependent. Specially at 1200°C, an interfacial phase reaction was observed, which bonded the interface tightly, as a result, the interfacial shear strength was up to ≈450 MPa. Employing the measured micro‐mechanical parameters of the composite constituents enabled the prediction of deformation mechanism of the composite in microscale, which suggested a dominant role of interface on the ductile/brittle behavior of the composite in tension and shear. Accordingly, the AS_f/Al₂O₃ composite exhibited a ductile‐to‐brittle transition as the sintering temperature increased from 800 to 1200°C, due to the prohibition of interfacial debonding at higher temperatures, in good agreement with numerical predictions. The proposed multiscale methodology provides a powerful tool to study the mechanical properties of oxide matrix composites qualitatively and quantitatively.