A field-based approach for deterimining ATOFMS instrument sensitities to ammonium and nitrate

Aerosol time-of-flight mass spectrometry (ATOFMS) instruments measure the size and chemical composition of individual particles in real-time. ATOFMS chemical composition measurements are difficult to quantify, largely because the instrument sensitivities to different chemical species in mixed ambient aerosols are unknown. In this paper, we develop a field-based approach for determining ATOFMS instrument sensitivities to ammonium and nitrate in size-segregated atmospheric aerosols, using tandem ATOFMS-impactor sampling. ATOFMS measurements are compared with collocated impactor measurements taken at Riverside, CA, in September 1996, August 1997, and October 1997. This is the first comparison of ion signal intensities from a single-particle instrument with quantitative measurements of atmospheric aerosol chemical composition. The comparison reveals that ATOFMS instrument sensitvities to both NH4+ and NO3- decline with increasing particle aerodynamic diameter over a 0.32-1.8 microm calibration range. The stability of this particle size dependence is tested overthe broad range of fine particle concentrations (PM1.8) = 17.6 +/- 2.0-127.8 +/- 1.8 microg m(-3)), ambient temperatures (23-35 degrees C), and relative humidity conditions (21-69%), encountered during the field experiments. This paper describes a potentially generalizable methodology for increasing the temporal and size resolution of atmospheric aerosol chemical composition measurements, using tandem ATOFMS-impactor sampling.     

Concentration and distribution of heavy metals in urban airborne particulate matter in Frankfurt am Main, Germany

Heavy metal concentrations were measured in airborne dust collected at three sites with different traffic densities from August 2001 to July 2002 in the Frankfurt am Main area. Bulk samples of particulate matter (PM) with an aerodynamic equivalent diameter of <22 microm were collected on cellulose nitrate filters using air filtration devices. Fractionated samples of PM with an aerodynamic equivalent diameter of <10 microm were collected using an eight-stage Andersen impactor. Pb, Cd, Mn, Ni, Zn, V, As, Sb, Cu, Cr, Co, and Ce were determined by inductively coupled plasma sector field mass spectrometry, Pt and Rh were determined by adsorptive voltammetry, and Pd was determined by total reflection X-ray fluorescence analysis. The results show that the highest airborne heavy metal concentrations occurred at the main street with a large volume of traffic. With the exception of Co, V, Ce, and Mn, the heavy metals had an elevated enrichment factor compared to their concentrations in the continental crust. The main street site was especially contaminated with Sb, Zn, Cu, V, and Ni. Motor vehicles are the likely source of emissions. With the exception of Cr, Cu, and Zn, most of the airborne heavy metal concentrations determined for impactor samples deviate slightly from the results for total airborne dust. Heavy metal particle size distributions can be divided into three groups. For metals such as As, Cd, Pb, and V, the main fraction can be found in fine particles with a diameter of <2.1 microm, whereas Ce, Cr, Co, and Ni occur mainly in coarse particles with a diameter of >2.1 microm. Cu, Mn, Sb, Zn, Pt, Pd, and Rh occur in high concentrations in the medium range of the impactor stages (particle diameters of 1.1-4.7 microm). Metal concentrations in fine dust particles are needed to assess the human health risks of their inhalation.     

Trace metals in ambient air: Hourly size-segregated mass concentrations determined by synchrotron-XRF

Trace metals are ubiquitous in urban ambient air, with mass concentrations in the range of a few microg/m3 down to less than 100 pg/m3. To measure such low concentrations represents a challenge for chemical and physical analysis. In this study, ambient aerosol was collected in Zürich (Switzerland) in 1-h intervals and three size fractions (aerodynamic diameters 0.1-1 microm, 1-2.5 microm, and 2.5-10 microm), using a three-stage rotating drum impactor (RDI). The samples were analyzed by energy-dispersive Synchrotron radiation X-ray fluorescence spectrometry (SR-XRF) to obtain size-segregated hourly elemental aerosol mass concentrations for Cr, Mn, Fe, Cu, Zn, Br, and Pb, along with S, Cl, and Ca under the selected experimental conditions. The high sensitivity of SR-XRF allowed for detection limits of <50 pg/m3 for most of the above elements, with a net analysis time of only 15 s per sample. The data obtained with this technique illustrate that there is a considerable gain of relevant information when time resolution for measurements is increased from 1 day to 1 h. The individual size fractions of a specific element may show significantly different short-term patterns.     

Characterization of saccharides in size-fractionated ambient particulate matter and aerosol sources: the contribution of primary biological aerosol particles (PBAPs) and soil to ambient particulate matter

Size-fractionated (equivalent to ambient PM2.5 and PM10) local soil, plant, and spore samples were collected in the Sonoran Desert near Phoenix, AZ and measured for saccharide content with the goal of characterizing ambient particulate matter sources including soil and primary biological aerosol particles (PBAPs) from plants and fungi. Different saccharide compositions were observed among soil, plant, and spore samples and between PM2.5 and PM10 fractions. The total measured nonlevoglucosan saccharide content relative to PM mass in ambient aerosols collected in a Phoenix suburb (Higley) was much higher compared to the local soil samples but much lower compared to the PBAP. The enrichment of saccharides from two saccharide-dominated PM source factors resolved by a positive matrix factorization model is also higher than the saccharide content in the size-fractionated local soil samples, but lower than that measured in the size-segregated PBAP samples. This indicates that ambient concentration of particulate saccharides at Higley was dominated by contributions from PBAPs directly injected into the atmosphere from plants and spores rather than from soil and associated biota. Our results also suggest the contribution to the fine size fraction of ambient PM from the primary biologically derived sources may be greater than previously acknowledged.     

Emissions of air pollutants from household stoves: honeycomb coal versus coal cake

Domestic coal combustion can emit various air pollutants. In the present study, we measured emissions of particulate matter (PM) and gaseous pollutants from burning a specially formulated honeycomb coal (H-coal) and a coal cake (C-coal). Flue gas samples for PM2.5, PM coarse (PM2.5-10), and TSP were collected isokinetically using a cascade impactor; PM mass concentrations were determined gravimetrically. Concentrations of SO2, NOx, and ionic Cr(VI) in PM were analyzed using spectrometric methods. Fluoride concentrations were measured using a specific ion electrode method. PM elemental components were analyzed using an X-ray fluorescence technique. Total (gas and particle phase) benzo[a]pyrene (BaP) concentration was determined using an HPLC/fluorescence method. Elemental and organic carbon contents of PM were analyzed using a thermal/optical reflectance technique. The compositional and structural differences between the H-coal and C-coal resulted in different emission characteristics. In generating 1 MJ of delivered energy, the H-coal resulted in a significant reduction in emissions of SO2 (by 68%), NOx (by 47%), and TSP (by 56%) as compared to the C-coal, whereas the emissions of PM2.5 and total BaP from the H-coal combustion were 2-3-fold higher, indicating that improvements are needed to further reduce emissions of these pollutants in developing future honeycomb coals. Although the H-coal and the C-coal had similar emission factors for gas-phase fluoride, the H-coal had a particle-phase fluoride emission factor that was only half that of the C-coal. The H-coal had lower energy-based emissions of all the measured toxic elements in TSP but higher emissions of Cd and Ni in PM2.5.     

Airborne brake wear debris: size distributions, composition, and a comparison of dynamometer and vehicle tests

Particle size distributions of light-duty vehicle brake wear debris are reported with careful attention paid to avoid sampling biases. Electrical low-pressure impactor and micro-orifice uniform deposit impactor measurements yield consistent size distributions, and the net particulate matter mass from each method is in good agreement with gravimetric filter measurements. The mass mean diameter of wear debris from braking events representative of urban driving is 6 microm, and the number-weighted mean is 1-2 microm for three currently used classes of lining materials: low metallic, semimetallic, and non-asbestos organic (NAO). In contrast, the wear rates are very material dependent, both in number and mass of particles, with 3-4 times higher emissions observed from the low metallic linings as compared to the semimetallic and NAO linings. Wind tunnel and test track measurements demonstrate the appearance of micron size particles that correlate with braking events, with approximately 50% of the wear debris being airborne for the test vehicle in this study. Elemental analysis of the wear debris reveals a consistent presence of the elements Fe, Cu, and Ba in both dynamometer and test track samples.     

Emission factors for carbonaceous particles and polycyclic aromatic hydrocarbons from residential coal combustion in China

Emission factors of carbonaceous particles, including black carbon (BC) and organic carbon (OC), and polycyclic aromatic hydrocarbons (PAHs) were determined for five coals, which ranged in maturity from sub-bituminous to anthracite. They were burned in the form of honeycomb briquettes in a residential coalstove, one of the most common fuel/stove combinations in China. Smoke samples were taken through dilution sampling equipment, with a high volume sampler that could simultaneously collect emissions in both particulate and gaseous phases, and a cascade impactor that could segregate particles into six fractions. Particulate BC and OC were analyzed by a thermal-optical method, and PAHs in emissions of both phases were analyzed by GC-MS. Burning of bituminous coals produced the highest emission factors of particulate matter (12.91 g/kg), BC (0.28 g/kg), OC (7.82 g/kg), and 20 PAHs (210.6 mg/kg) on the basis of burned dry ash-free (daf) coal, while the anthracite honeycomb-briquette was the cleanest household coal fuel. The size-segregated results show that more than 94% of the particles were submicron, and calculated mass median aerodynamic diameters (MMAD) of all particles were under 0.3 microm. Based on the coal consumption in the residential sector of China, 290.24 Gg (gigagrams) of particulate matter, 5.36 Gg of BC, 170.33 Gg of OC, and 4.72 Gg of 20 PAHs mass were emitted annually from household honeycomb-briquette burning during 2000. Anthracite coal should be selected preferentially and more advanced burning conditions should be applied in domestic combustion, from the viewpoint of both climate change and adverse health effects.     

Variability of apparent particle density of an urban aerosol

The day to day and diurnal variation of apparent particle density was studied using highly time-resolved measurements of particle number distribution and fine-particle mass concentration. The study was conducted in Erfurt, Germany, from January 1, 1999, to November 22, 2000. A setup consisting of a differential mobility particle spectrometer and a laser aerosol spectrometer was used for particle number distribution measurements. PM2.5 particle mass was measured in parallel on an hourly basis using a tapered element oscillating microbalance (TEOM) and on daily base by using a Harvard marple impactor (HI). For the estimation of the mean apparent density of particles, number size distributions were converted into volume size distributions, assuming that the particles were spherically shaped. The volume size distributions were integrated over the range of 10 nm to 2.03 microm Stokes equivalent diameter to obtain volume concentrations. Mean apparent particle density was calculated as ratio of mass concentration and volume concentration. The mean apparent particle density, determined from HI and number size distribution on a daily basis was 1.6 +/- 0.5 g cm(-3). We found a strong day-to-day variation of apparent density ranging from 1.0 to 2.5 g cm(-3) (5th and 95th percentile). Furthermore, the apparent density showed pronounced diurnal pattern both in summer and in winter and also on weekdays and weekends. The apparent density was lowest in the morning and highest in the afternoon. The mean apparent density on an hourly basis was 1.4 +/- 0.5 and 1.5 +/- 0.5 g cm(-3) for PM2.5TEOM and corrected PM2.5TEOM using regression equation between daily mass concentration of HI and TEOM, respectively. The strong diurnal variation of apparent particle density was associated predominantly with the vertical temperature inversion and with traffic intensity. Thus, the apparent particle density depends on the physical particle properties and might be related to chemical composition of the sampled particle.     

The effects of the catalytic converter and fuel sulfur level on motor vehicle particulate matter emissions: gasoline vehicles

Scanning mobility and electrical low-pressure impactor particle size measurements conducted during chassis dynamometer testing reveal that neither the catalytic converter nor the fuel sulfur content has a significant effect on gasoline vehicle tailpipe particulate matter (PM) emissions. For current technology, port fuel injection, gasoline engines, particle number emissions are < or = 2 times higher from vehicles equipped with blank monoliths as compared to active catalysts, insignificant in contrast to the 90+% removal of hydrocarbons. PM mass emission rates derived from the size distributions are equal within the experimental uncertainty of 50-100%. Gravimetric measurements exhibit a 3-10-fold PM mass increase when the active catalyst is omitted, which is attributed to gaseous hydrocarbons adsorbing onto the filter medium. Both particle number and gravimetric measurements show that gasoline vehicle tailpipe PM emissions are independent (within 2 mg/mi) of fuel sulfur content over the 30-990 ppm concentration range. Nuclei mode sulfate aerosol is not observed in either test cell measurements or during wind tunnel testing. For three-way catalyst equipped vehicles, the principal sulfur emission is SO2; however a sulfur balance is not obtained over the drive cycle. Instead, sulfur is stored on the catalyst during moderate driving and then partially removed during high speed/load operation.     

Real-world emission factors of fine and ultrafine aerosol particles for different traffic situations in Switzerland

Extended field measurements of particle number (size distribution of particle diameters, D, in the range between 18 nm and 10 microm), surface area concentrations, and PM1 and PM10 mass concentrations were performed in Switzerland to determine traffic emissions using a comprehensive set of instruments. Measurements took place at roads with representative traffic regimes: at the kerbside of a motorway (120 km h(-1)), a highway (80-100 km h(-1)), and in an urban area with stop-and-go traffic (0-50 km h(-1)) regulated by light signals. Mean diurnal variations showed that the highest pollutant concentrations were during the morning rush hours, especially of the number density in the nanoparticle size range (D <50 nm). From the differences between up- and downwind concentrations (or differences between kerbside and background concentrations for the urban site), "real-life" emission factors were derived using NOx concentrations to calculate dilution factors. Particle number and volume emission factors of different size ranges (18-50 nm, 18-100 nm, and 18-300 nm) were derived for the total vehicle fleet and separated into a light-duty (LDV) and a heavy-duty vehicle (HDV) contribution. The total particle number emissions per vehicle were found to be about 11.7-13.5 x 10(14) particles km(-1) for constant speed (80-120 km h(-1) and 3.9 x 10(14) particles km(-1) for urban driving conditions. LDVs showed higher emission factors at constant high speed than under urban disturbed traffic flow. In contrast, HDVs emitted more air pollutants during deceleration and acceleration processes in stop-and-go traffic than with constant speed of about 80 km h(-1). On average, one HDV emits a 10-30 times higher amount of particulate air pollutants (in terms of both number and volume) than one LDV.     

Indoor particulate matter of outdoor origin: importance of size-dependent removal mechanisms

Adverse human health effects have been observed to correlate with levels of outdoor particulate matter (PM), even though most human exposure to PM of outdoor origin occurs indoors. In this study, we apply a model and empirical data to explore the indoor PM levels of outdoor origin for two major building types: offices and residences. Typical ventilation rates for each building type are obtained from the literature. Published data are combined with theoretical analyses to develop representative particle penetration coefficients, deposition loss rates, and ventilation-system filter efficiencies for a broad particle size range (i.e., 0.001-10 microm). We apply archetypal outdoor number, surface area, and mass PM size distributions for both urban and rural airsheds. We also use data on mass-weighted size distributions for specific chemical constituents of PM: sulfate and elemental carbon. Predictions of the size-resolved indoor proportion of outdoor particles (IPOP) for various conditions and ambient particle distributions are then computed. The IPOP depends strongly on the ambient particle size distribution, building type and operational parameters, and PM metric. We conclude that an accurate determination of exposure to particles of ambient origin requires explicit consideration of how removal processes in buildings vary with particle size.     

Size-resolved emissions of organic tracers from light- and heavy-duty vehicles measured in a California roadway tunnel

Individual organic compounds found in particulate emissions from vehicles have proven useful in source apportionment of ambient particulate matter. Species of interest include the hopanes, originating in lube oil, and selected PAHs generated via combustion. Most efforts to date have focused on emissions and apportionment PM10 or PM2.5 However, examining how these compounds are segregated by particle size in both emissions and ambient samples will help efforts to apportion size-resolved PM, especially ultrafine particles which have been shown to be more potent toxicologically. To this end, high volume size-resolved (coarse, accumulation, and ultrafine) PM samples were collected inside the Caldecott tunnel in Orinda, California to determine the relative emission factors for these compounds in different size ranges. Sampling occurred in two bores, one off-limits to heavy-duty diesel vehicles, which allows determination of the different emissions profiles for diesel and gasoline vehicles. Although tunnel measurements do not measure emissions over a full engine duty cycle, they do provide an average emissions profile over thousands of vehicles that can be considered characteristic of "freeway" emissions. Results include size-fractionated emission rates for hopanes, PAHs, elemental carbon, and other potential organic markers apportioned to diesel and gasoline vehicles. The results are compared to previously conducted PM2.5 emissions testing using dynamometer facilities and othertunnel environments.     

Particulate and trace gas emissions from open burning of wheat straw and corn stover in China

Field measurements were conducted to determine particulate emissions and trace gas emissions, including CO2, CO, CH4, NMHCs, NOx, NH3, N2O, and SO2, from open burning of wheat straw and maize stover, two major agricultural residues in China. The headfire ignition technique was adopted, and sampling was performed downwind from the agricultural fire. Particulate matter (PM) and gas emission factors were determined using the carbon mass-balance method. Particle mass size distributions show a prominent accumulation mode peak at 0.26-0.38 microm. Submicron particles dominate PM emissions. Most measured chemical species measured show a similar size distribution as PM. Chemical composition analysis indicates that PM2.5 is largely composed of carbon, K, and Cl. PM2.5 emission factors of wheat straw and maize stover are 7.6 +/- 4.1 g/kg and 11.7 +/- 1.0 g/kg, respectively, It also indicates that 12.1-24.2% of N in biomass is released as nitrogen-based trace gases and 11.0-24.9% of fuel S is emitted as SO2.     

Fine (PM2.5) and coarse (PM2.5-10) particulate matter on a heavily trafficked London highway: sources and processes

A large dataset for PM2.5 and PMcoarse (PM2.5-10) concentrations monitored near a busy London highway (Marylebone Road) has been analyzed to define the factors that lead to high concentrations. The following have been highlighted as major influencing parameters: wind speed, prevailing wind direction (because of its role on the microscale dispersion within the street), the daily cycle of the atmospheric boundary layer (stable during the night/ convective and mixed during the day), and traffic density. The mainly diesel heavy-duty vehicles are the main source of fine particulate matter at Marylebone Road. In particular, lorries (trucks) dominate PM10 exhaust emissions which are mainly in the fine (<2.5 microm) size range. A strong correlation with PMcoarse suggests that the heavy-duty traffic is largely responsible for this component also. Substantial local increments in PM2.5 and PMcoarse due to traffic have been estimated and a large part of the increment in PMcoarse concentrations is inferred to arise from resuspended road dust emissions since the contribution of abrasion processes estimated from emission factors is modest. Despite the strong influence of traffic on PM concentrations measured at Marylebone Road the analysis of factors leading to the highest 5% of hourly concentrations of PM10 at Marylebone Road reveals that almost half of these events were due to building works. The other events occurred when all or most of the key factors occurred simultaneously (heavy traffic, poor dispersion, etc.). Some episodes of high PM2.5 concentrations were associated with long-range transport in which the regional PM2.5 constituted most of the local concentrations.     

Concentration and distribution of platinum group elements (Pt, Pd, Rh) in airborne particulate matter in Frankfurt am Main, Germany

The concentrations and distribution of platinum group elements (Pt, Pd, Rh) in airborne particulate matter were studied in a period of one year from August 2001 to July 2002 in urban and in nonurban areas. Airborne dust samples were collected as a total amount (particles with an aerodynamic diameter <22 microm) and classified using an eight-stage Andersen impactor (<10 microm) at three locations with different traffic density roads in the Frankfurt am Main and nonurban areas. Sampling at the three locations was performed simultaneously for total airborne dust and fractionated airborne dust. Pd was determined by total reflection X-ray fluorescence after Hg coprecipitation. Pt and Rh were analyzed by adsorptive striping voltammetry after HPA digestion. The results show that the PGE concentrations in airborne samples depend on the traffic density. The highest PGE concentrations in air were found in the vicinity of major roads with heavy traffic, and the lowest ones were found in the nonurban area. The presence of PGE at the sampling station relatively free of traffic in a nonurban area hints to a transport of some of the emitted PGE from the city to this station by wind. At all three sampling locations, a heterogeneous distribution of the Pd, Pt, and Rh concentrations during the sampling year can be observed. The sum of PGE concentrations in total airborne dust is comparable with the sum of impactor samples. However, the concentration of Pt and Rh in total airborne dust (<22 microm) is on average higher than in impactor samples (<10 microm). On the contrary, Pd concentration is higher in impactor samples in most cases. The airborne PGE distribution is dominated by Pt, followed by Pd and Rh. The impactor samples are dominated by Pd, followed by Pt and Rh. This fact indicates that palladium occurs mainly in relatively fine airborne particles. The main fraction of PGE is found on average in particle sizes between 1.1 and 4.7 microm. Knowledge of the size distribution of particles containing PGE is important with respect to risk assessment of human inhalation.     

PAHs, PAH-induced carcinogenic potency, and particle-extract-Induced cytotoxicity of traffic-related nano/ultrafine particles

Polycyclic aromatic hydrocarbons (PAHs) bound in nano/ ultrafine particles from vehicle emissions may cause adverse health effects. However, little is known about the characteristics of the nanoparticle-bound PAHs and the PAH-associated carcinogenic potency/cytotoxicity; therefore, traffic-related nano/ultrafine particles were collected in this study using a microorifice uniform deposition impactor(MOUDI) and a nano-MOUDI. For PM0.056--18, the difference in size-distribution of particulate total-PAHs between non-after-rain and after-rain samples was statistically significant at alpha = 0.05; however, this difference was not significant for PM0.01--0.056. The PAH correlation between PM0.01--0.1 and PM0.1--1.8 was lower for the after-rain samples than forthe non-after-rain samples. The average particulate total-PAHs in five samplings displayed a trimodal distribution with a major peak in the Aitken mode (0.032--0.056 microm). About half of the particulate total-PAHs were in the ultrafine size range. The BaPeq sums of BaP, IND, and DBA (with toxic equivalence factors > or = 0.1) accounted for approximately 90% of the total-BaPeq in the nano/ultrafine particles, although these three compounds contributed little to the mass of the sampled particles. The mean content of the particle-bound total-PAHs/-BaPeqs and the PAH/BaPeq-derived carcinogenic potency followed the order nano > ultrafine > fine > coarse. For a sunny day sample, the cytotoxicity of particle extracts (using 1:1 (v/v) n-hexane/dichloromethane) was significantly higher (p < 0.05) for the nano (particularly the 10-18 nm)/ultrafine particles than for the coarser particles and bleomycin. Therefore, traffic-related nano and ultrafine particles are possibly cytotoxic.     

Fingerprinting metals in urban street dust of Beijing, Shanghai, and Hong Kong

Street dust samples were taken between July and December 2005 at 25 locations in Shanghai, Beijing, and Hong Kong and sieved to 63 microm particle size before elemental analyses by CHN analyzer, XRF and ICP-MS. About 60% of the particles from the Beijing and Shanghai sieved samples were < 10 microm mean diameter, and approximately 20% were < 2 microm mean diameter, so that they are readily resuspendable and respirable with increased risk of adverse health impacts. The optical size distributions determined by electron microscopy were reasonably similar to the mass size distributions of total suspended particulate matter (TSP) at these two megacities. Hong Kong street dust particles were coarser with only about 3% of the sieved samples being < 10 microm. The elemental composition profile of Hong Kong street dust differs considerably from those of Beijing and Shanghai, being more abundant in C, S, Cr, Cu, Ce, and Zn due to higher traffic density. In particular, the vehicle contribution to Hong Kong street dust is shown by order-of-magnitude relative enhancements of Fe and Cr compared with those in TSP sampled nearby, attributed to vehicle iron and stainless-steel wear and tear and rusting contributing to street dust in the street canyons. The concentrations of Cr in Hong Kong street dust, measured from 52Cr and 53Cr by ICP-DRC-MS after a modified three-stage microwave-assisted acid digestion, are higher than those reported elsewhere.     

Particulate oxidative burden associated with firework activity

Firework events are capable of inducing particulate matter (PM) episodes that lead to exceedances of regulatory limit values. As short-term peaks in ambient PM concentration have been associated with negative impacts on respiratory and cardiovascular health, we performed a detailed study of the consequences of firework events in London on ambient air quality and PM composition. These changes were further related to the oxidative activity of daily PM samples by assessing their capacity to drive the oxidation of physiologically important lung antioxidants including ascorbate, glutathione and urate (oxidative potential, OP). Twenty-four hour ambient PM samples were collected at the Marylebone Road sampling site in Central London over a three week period, including two major festivals celebrated with pyrotechnic events: Guy Fawkes Night and Diwali. Pyrotechnic combustion events were characterized by increased gas phase pollutants levels (NO(x) and SO(2)), elevated PM mass concentrations, and trace metal concentrations (specifically Sr, Mg, K, Ba, and Pb). Relationships between NO(x), benzene, and PM(10) were used to apportion firework and traffic source fractions. A positive significant relationship was found between PM oxidative burden and individual trace metals associated with each of these apportioned source fractions. The level of exposure to each source fraction was significantly associated with the total OP. The firework contribution to PM total OP, on a unit mass basis, was greater than that associated with traffic sources: a 1 μg elevation in firework and traffic PM fraction concentration was associated with a 6.5 ± 1.5 OP(T) μg(-1) and 5.2 ± 1.4 OP(T) μg(-1) increase, respectively. In the case of glutathione depletion, firework particulate OP (3.5 ± 0.8 OP(GSH) μg(-1)) considerably exceeded that due to traffic particles (2.2 ± 0.8 OP(GSH) μg(-1)). Therefore, in light of the elevated PM concentrations caused by firework activity and the increased oxidative activity of this PM source, there is value in examining if firework derived PM is related to acute respiratory outcomes.     

Physical and chemical characterization of residential oil boiler emissions

The toxicity of emissions from the combustion of home heating oil coupled with the regional proximity and seasonal use of residential oil boilers (ROB) is an important public health concern. Yet scant physical and chemical information about the emissions from this source is available for climate and air quality modeling and for improving our understanding of aerosol-related human health effects. The gas- and particle-phase emissions from an active ROB firing distillate fuel oil (commonly known as diesel fuel) were evaluated to address this deficiency. Ion chromatography of impactor samples showed that the ultrafine ROB aerosol emissions were approximately 45% (w/w) sulfate. Gas chromatography-mass spectrometry detected various n-alkanes at trace levels, sometimes in accumulation mode particles, and out of phase with the size distributions of aerosol mass and sulfate. The carbonaceous matter in the ROB aerosol was primarily light-adsorbing elemental carbon. Gas chromatography-atomic emission spectroscopy measured a previously unrecognized organosulfur compound group in the ROB aerosol emissions. High-resolution transmission electron microscopy of ROB soot indicated the presence of a highly ordered primary particle nanostructure embedded in larger aggregates. Organic gas emissions were measured using EPA Methods TO-15 and TO-11A. The ROB emitted volatile oxygenates (8 mg/(kg of oil burned)) and olefins (5 mg/(kg of oil burned)) mostly unrelated to the base fuel composition. In the final analysis, the ROB tested was a source of numerous hazardous air pollutants as defined in the Clean Air Act Amendments. Approximations conducted using emissions data from the ROB tests show relatively low contributions to a regional-level anthropogenic emissions inventory for volitile organic compounds, PM2.5, and SO2 mass.     

Size distribution of particle-phase molecular markers during a severe winter pollution episode

Airborne particulate matter was collected using filter samplers and cascade impactors in six size fractions below 1.8 microm during a severe winter air pollution event at three sites in the Central Valley of California. The smallest size fraction analyzed was 0.056 < Dp <0.1 microm particle diameter, which accounts for the majority of the mass in the ultrafine (PM0.1) size range. Separate samples were collected during the daytime (10 a.m. to 6 p.m. PST) and nighttime (8 p.m. to 8 a.m. PST) to characterize diurnal patterns. Each sample was extracted with organic solvents and analyzed using gas chromatography mass spectrometry for molecular markers that can be used for size-resolved source apportionment calculations. Colocated impactor and filter measurements were highly correlated (R8 > 0.8) for retene, benzo[ghi]flouranthene, chrysene, benzo[b]fluoranthene, benzo[k]fluoranthene, benzo[e]pyrene, benzo[a]pyrene, perylene, indeno[1,2,3-cd]pyrene, benzo[ghi]perylene, coronene, MW302 polycyclic aromatic hydrocarbon (PAHs), 17beta(H)-21alpha(H)-30-norhopane, 17alpha(H)-21beta(H)-hopane, alphabetabeta-20R-C29-ethylcholestane, levoglucosan, and cholesterol. Of these compounds, levoglucosan was present in the highest concentration (60-2080 ng m(-3)) followed by cholesterol (6-35 ng m(-3)), PAHs (2-38 ng m(-3)), and hopanes and steranes (0-2 ng m(-3)). Nighttime concentrations were higher than daytime concentrations in all cases. Organic compound size distributions were generally similar to the total carbon size distributions during the nighttime but showed greater variability during the daytime. This may reflect the dominance of fresh emission in the stagnant surface layer during the evening hours and the presence of aged organic aerosol at the surface during the daytime when the atmosphere is better mixed. All of the measured organic compound particle size distributions had a single mode that peaked somewhere between 0.18 and 0.56 microm, but the width of each distribution varied by compound. Cholesterol generally had the broadest particle size distribution, while benzo[ghi]perylene and 17alpha(H)-21beta(H)-29-norhopane generally had sharper peaks. The difference between the size distributions of the various particle-phase organic compounds reflects the fact that these compounds exist in particles emitted from different sources. The results of the current study will prove useful for size-resolved source apportionment exercises.