Enhancement of oxygen storage capacity by reductive treatment of Al2O3 and CeO2–ZrO2 solid solution nanocomposite

Oxygen storage capacity (OSC) of CeO₂–ZrO₂ solid solution, Ce_xZr_(1−x)O₄, is one of the most contributing factors to control the performance of an automotive catalyst. To improve the OSC, heat treatments were employed on a nanoscaled composite of Al₂O₃ and CeZrO₄ (ACZ). Reductive treatments from 700 to 1000 °C significantly improved the complete oxygen storage capacity (OSC-c) of ACZ. In particular, the OSC-c measured at 300 °C reached the theoretical maximum with a sufficient specific surface area (SSA) (35 m²/g) after reductive treatment at 1000 °C. The introduced Al₂O₃ facilitated the regular rearrangement of Ce and Zr ions in CeZrO₄ as well as helped in maintaining the sufficient SSA. Reductive treatments also enhanced the oxygen release rate (OSC-r); however, the OSC-r variation against the evaluation temperature and the reduction temperature differed from that of OSC-c. OSC-r measured below 200 °C reached its maximum against the reduction temperature at 800 °C, while those evaluated at 300 °C increased with the reduction temperature in the same manner as OSC-c.     

Oxidation of CH4 over Pd supported on TiO2-doped SiO2: Effect of Ti(IV) loading and influence of SO2

Titania-modified silicas with different weight% of TiO₂ were prepared by sol–gel method and used as supports for Pd (1 wt%) catalysts. The obtained materials were tested in the oxidation of methane under lean conditions in absence and in presence of SO₂. Test reactions were consecutively performed in order to evaluate the thermal stability and poisoning reversibility. Increasing amounts of TiO₂ improved the catalytic activity, with an optimum of the performance for 10 wt% TiO₂ loading. Moreover, the titania-containing catalysts exhibited a superior tolerance towards SO₂ by either adding it to the reactants or feeding it as a pure pretreatment atmosphere at 350 °C. Catalysts were characterized by XPS, XRD, FT-IR and BET measurements. According to the structural and surface analyses, the mixed oxides contained Si–O–Ti linkages which were interpreted as being responsible for the enhanced intrinsic activity of supported PdO with respect to PdO on either pure SiO₂ or pure TiO₂. Moreover, the preferential interaction of the sulfur molecule with TiO₂ and the easy SO_x desorption from high surface area silica were the determining factors for the superior SO₂ tolerance of the TiO₂-doped catalysts.     

Rapid synthesis of Ti3AlC2/TiB2 composites by the spark plasma sintering (SPS) technique

Dense Ti₃AlC₂/TiB₂ composites were successfully fabricated from B₄C/TiC/Ti/Al powders by spark plasma sintering (SPS). The microstructure, flexural strength and fracture toughness of the composites were investigated. The experimental results indicate that the Vickers hardness increased with the increase in TiB₂ content. The maximum flexural strength (700 ± 10 MPa) and fracture toughness (7.0 ± 0.2 MPa m^1/2) were achieved through addition of 10 vol.% TiB₂, however, a slight decrease in the other mechanical properties was observed with TiB₂ addition higher than 10 vol.%, which is believed to be due to TiB₂ agglomeration.     

Meldola blue immobilized on a new SiO2/TiO2/graphite composite for electrocatalytic oxidation of NADH

Meldola blue immobilized on a new SiO₂/TiO₂/graphite composite was applied in the electrocatalytic oxidation of NADH. The materials were prepared by the sol-gel processing method and characterized by several techniques including scanning electronic microscopy coupled to energy dispersive spectroscopy (SEM-EDS), X-ray photoelectron spectroscopy (XPS) and high-resolution transmission electronic microscopy (HRTEM). Si and Ti mapping profiles on the surface showed a homogeneous distribution of the components. Ti2p binding energy peaks indicate that the formation of Si-O-Ti linkage is presumably the responsible for the high rigidity of the matrices. The good electrical conductivity presented by the composites (5 and 11 S cm⁻¹) can be related to a homogeneous distribution of graphite particles observed by TEM. After the materials characterization, a SiO₂/TiO₂/graphite electrode was prepared and some chemical modifications were performed on its surface to promote the adsorption of meldola blue. The resulting system presented electrocatalytic properties toward the oxidation of NADH, decreasing the oxidation potential to −120 mV. The proposed sensor showed a wide linear response range from 0.018 to 7.29 mmol l⁻¹ and limit of detection of 0.008 mmol l⁻¹. SiO₂/TiO₂/graphite has shown to be a promising material to be used as a suitable support in the construction of new electrochemical sensors.     

Effect of ceria on the structure and catalytic activity of V2O5/TiO2–ZrO2 for oxidehydrogenation of ethylbenzene to styrene utilizing CO2 as soft oxidant

The present study was undertaken to investigate the influence of ceria on the physicochemical and catalytic properties of V₂O₅/TiO₂–ZrO₂ for oxidative dehydrogenation of ethylbenzene to styrene utilizing CO₂ as a soft oxidant. Monolayer equivalents of ceria, vanadia and ceria–vanadia combination over TiO₂–ZrO₂ (TZ) support were impregnated by a coprecipitation and wet impregnation methods. Synthesized catalysts were characterized by using X-ray diffraction, Raman spectroscopy, X-ray photoelectron spectroscopy, temperature programmed reduction, transmission electron microscopy and BET surface area methods. The XRD profiles of 550 °C calcined samples revealed amorphous nature of the materials. Upon increasing calcination temperature to 750 °C, in addition to ZrTiO₄ peaks, few other lines due to ZrV₂O₇ and CeVO₄ were observed. The XPS V 2p results revealed the existence of V⁴⁺ and V⁵⁺ species at 550 and 750 °C calcinations temperatures, respectively. TEM analysis suggested the presence of nanosized (<7 nm) particles with narrow range distribution. Raman measurements confirmed the formation ZrTiO₄ under high temperature treatments. TPR measurements suggested a facile reduction of CeO₂–V₂O₅/TZ sample. Among various samples evaluated, the CeO₂–V₂O₅/TZ sample exhibited highest conversion and nearly 100% product selectivity. In particular, the addition of ceria to V₂O₅/TZ suppressed the coke deposition and allowed a stable and high catalytic activity.     

Decomposition of ozone on Ag/SiO2 catalyst for abatement of waste gases emissions

A silica-supported Ag system made by the incipient wetness impregnation method was investigated in the reaction of heterogeneous catalytic decomposition of ozone. It was established that the catalytic ozone decomposition on Ag/SiO₂ proceeded in the temperature interval −40 °C to 25 °C as a first order reaction with activation energy of 65 kJ/mol (pre-exponential factor 5.0 × 10¹⁴ s⁻¹). Based on the results from the instrumental methods (SEM, XRD, XPS, EPR, TPD) it can be concluded that in presence of ozone the silver is oxidized to a complicated mixture of Ag₂O₃ and AgO. Due to the high activity and stability of the Ag/SiO₂ catalyst, it is promising for neutralization of waste gases containing ozone.     

Low-temperature firing and microwave dielectric properties of 16CaO–9Li2O–12Sm2O3–63TiO2 ceramics with V2O5 addition

The sintering behaviors and microwave dielectric properties of the 16CaO–9Li₂O–12Sm₂O₃–63TiO₂ (abbreviated CLST) ceramics with different amounts of V₂O₅ addition had been investigated in this paper. The sintering temperature of the CLST ceramic had been efficiently decreased by nearly 100 °C. No secondary phase was observed in the CLST ceramics and complete solid solution of the complex perovskite phase was confirmed. The CLST ceramics with small amounts of V₂O₅ addition could be well sintered at 1200 °C for 3 h without much degradation in the microwave dielectric properties. Especially, the 0.75 wt.% V₂O₅-doped ceramics sintered at 1200 °C for 3 h have optimum microwave dielectric properties of Kr = 100.4, Q × f = 5600 GHz, and TCF = 7 ppm/°C. Obviously, V₂O₅ could be a suitable sintering aid that improves densification and microwave dielectric properties of the CLST ceramics.     

Structure and performance of a novel TiO2-phosphonate composite photocatalyst

An innovative SiO₂-PO₄³⁻-TiO₂ photocatalyst is presented which is able to bond TiO₂ to Raschig rings (RR). Evidence for the formation on the catalyst surface of PO stretching bands near 1200–1250 cm⁻¹ is presented by FTIR spectroscopy. The TiO₂ Degussa P25 on the catalyst surface (RR) was further characterized by high-resolution transmission electron microscopy (HRTEM), and X-ray diffraction showing that the composite catalyst prepared at 500 °C does not alter the particle size or crystallographic composition of the TiO₂ Degussa P25 particles. The Ti- and P-distribution of the catalyst surface overlayers was obtained by Ar-sputtering eroding up to 100 topmost catalyst layers. By atomic force microscopy (AFM) the root mean square roughness (Rq) or rugosity of 771 nm and an average height of the catalyst layer of 1.52 μm were found on the glass surface. The root mean square roughness Rq varies very little in value before and after the photocatalysis indicating that the sample porosity is conserved during 4-CP photodegradation. The disappearance kinetics of 4-chlorophenol (4-CP) on the SiO₂-PO₄³⁻-TiO₂ composite occurred within 15 min and was faster than the 45 min needed with suspensions of TiO₂ Degussa P25 (1 g L⁻¹). The SiO₂-PO₄³⁻-TiO₂ photocatalyst was able to degrade repetitively 4-CP solutions without loss of activity. The effect of the light intensity, oxidant concentration and 4-CP concentration on the photodegradation kinetics was investigated and is reported in this study.     

Impact of supercritical drying and heat treatment on physical properties of titania/silica aerogel monolithic and its applications

TiO₂–SiO₂ monolithic aerogels were homogeneously prepared using sol–gel method. Critical point of drying of TiO₂–SiO₂ gels with ethanol was studied for 30, 60, 90 and 120 min. Subsequently, the gels were dried with supercritical ethanol, resulting in amorphous aerogels that crystallized following heat treatment at 550 °C from 1 to 5 h. The TiO₂–SiO₂ aerogels were characterized using X-ray diffraction (XRD), scanning electron microscopy (SEM) and surface area measurements. The molar ratio of SiO₂:TiO₂ was 6 and the synthetic strategy revealed that TiO₂–SiO₂ aerogel, had a surface area 868 m²/g, particle size 40 nm, density 0.17 g/cm³ and 80% porosity. The finding indicated that from economic point of view, TiO₂–SiO₂ gel should be supercritical dried for 30 min and heat-treated for 5 h. The TiO₂–SiO₂ aerogel monoliths photocatalyst synthesized using sol–gel method provided insight into the characteristics that make a photocatalyst material well-suited for photodegradation of phenol and cyanide in an industrial waste stream containing Cl⁻, S²⁻ and NH₄⁺. Interestingly, after multiple reuse cycles (i.e. ≥7), photodegradation systems with regenerated photocatalyst showed a slightly decreasing of photoactivity 2–4%. The overall kinetics of photodegradation of either phenol or cyanide using TiO₂–SiO₂ aerogel photocatalyst was found to be of first order.     

Direct synthesis of mesoporous silicalite-1 supported TiO2–ZrO2 for the dehydrogenation of EB to styrene with CO2

Direct synthesis route was developed to support TiO₂–ZrO₂ binary metal oxide onto the carbon templated mesoporous silicalite-1 (CS-1). Metal hydroxide modified carbon particles could play a role as hard template and simultaneously support metal components on the mesopores during the crystallization of zeolites. Such supported TiO₂–ZrO₂ binary metal oxides (TZ/CS-1) showed better resistance to deactivation in the oxidative dehydrogenation of ethylbenzene (ODHEB) in the presence of CO₂. These catalysts were found to be active, selective and catalytically stable (10 h of time-on-stream) at 600 °C for the dehydrogenation of ethylbenzene (EB) to styrene (Sty).     

Facile preparation of Na-free anatase TiO2 film with highly photocatalytic activity on soda-lime glass

Na-free anatase TiO₂ film was prepared on soda-lime glass (SL-glass) from a TiF₄ aqueous solution upon addition of boric acid at 60 °C. It was found that the as-prepared TiO₂ film before calcination showed a higher photocatalytic activity than the calcined sample (500 °C). This could be attributed to the fact that the calcined TiO₂ film contained decent Na⁺ ions, which was diffused from the SL-glass substrate into the TiO₂ film during calcination, resulting in the decrease of photocatalytic activity.     

CO hydrogenation to iso-C4 hydrocarbons over CeO2–TiO2 catalysts

CeO₂–TiO₂ (Ce:Ti = 0.25–9, molar ratio) catalysts were synthesized by a sol–gel method and the catalytic performances were evaluated in the selective synthesis of isobutene and isobutane from CO hydrogenation under the reaction conditions of 673–748 K, 1–5 MPa and 720–3000 h⁻¹. The physical properties, such as specific surface area, cumulative pore volume, average pore diameter, crystal phase and size, of the catalysts were characterized by N₂ adsorption/desorption and XRD. All the CeO₂–TiO₂ composite oxides showed higher surface areas than pure TiO₂ and CeO₂. No TiO₂ phase was detected on the samples of CeO₂–TiO₂ in which TiO₂ contents were in the range of 10–50 mol%. Crystalline Ce₂O₃ was detected in CeO₂–TiO₂ (8:2). The reaction conditions, temperature, pressure and space velocity, had obvious influences on the CO conversion and distribution of the products over CeO₂–TiO₂ (8:2) catalyst.     

Electrical properties of V2O5–WO3/TiO2 EUROCAT catalysts evidence for redox process in selective catalytic reduction (SCR) deNOx reaction

Electrical conductivity measurements on EUROCAT V₂O₅–WO₃/TiO₂ catalyst and on its precursor without vanadia were performed at 300°C under pure oxygen to characterize the samples, under NO and under NH₃ to determine the mode of reactivity of these reactants and under two reaction mixtures ((i) 2000 ppm NO + 2000 ppm NH₃ without O₂, and (ii) 2000 ppm NO + 2000 ppm NH₃ + 500 ppm O₂) to put in evidence redox processes in SCR deNO_x reaction.It was first demonstrated that titania support contains certain amounts of dissolved W⁶⁺ and V⁵⁺ ions, whose dissolution in the lattice of titania creates an n-type doping effect. Electrical conductivity revealed that the so-called reference pure titania monolith was highly doped by heterovalent cations whose valency was higher than +4. Subsequent chemical analyses revealed that so-called pure titania reference catalyst was actually the WO₃/TiO₂ precursor of V₂O₅–WO₃/TiO₂ EUROCAT catalyst. It contained an average amount of 0.37 at.% W⁶⁺dissolved in titania, i.e. 1.07 × 10²⁰ W⁶⁺ cations dissolved/cm³ of titania. For the fresh catalyst, the mean amounts of W⁶⁺ and V⁵⁺ ions dissolved in titania were found to be equal to 1.07 × 10²⁰ and 4.47 × 10²⁰ cm⁻³, respectively. For the used catalyst, the mean amounts of W⁶⁺ and V⁵⁺ ions dissolved were found to be equal to 1.07 × 10²⁰ and 7.42 × 10²⁰ cm⁻³, respectively. Since fresh and used catalysts have similar compositions and similar catalytic behaviours, the only manifestation of ageing was a supplementary progressive dissolution of 2.9 × 10²⁰ additional V⁵⁺ cations in titania.After a prompt removal of oxygen, it appeared that NO alone has an electron acceptor character, linked to its possible ionosorption as NO⁻ and to the filling of anionic vacancies, mostly present on vanadia. Ammonia had a strong reducing behaviour with the formation of singly ionized vacancies. A subsequent introduction of NO indicated a donor character of this molecule, in opposition to its first adsorption. This was ascribed to its reaction with previously adsorbed ammonia strongly bound to acidic sites. Under NO + NH₃ reaction mixture in the absence of oxygen, the increase of electrical conductivity was ascribed to the formation of anionic vacancies, mainly on vanadia, created by dehydroxylation and dehydration of the surface. These anionic vacancies were initially subsequently filled by the oxygen atom of NO. N^o atoms, resulting from the dissociation of NO and from ammonia dehydrogenation, recombined into dinitrogen molecules. The reaction corresponded to

Full-size image

. In the presence of oxygen, NO did not exhibit anymore its electron acceptor character, since the filling of anionic vacancies was performed by oxygen from the gas phase. NO reacted directly with ammonia strongly bound on acidic sites. A tentative redox mechanism was proposed for both cases.     

A VOx/meso-TiO2 catalyst for methanol oxidation to dimethoxymethane

Mesoporous TiO₂ was prepared by simply controlling the hydrolysis of Ti(OBu)₄ with the help of acetic acid. The mesoporous TiO₂ had a well-crystallized anatase phase and a high surface area of 290 m² g⁻¹ with a pore size of about 4 nm. The anatase phase and the mesoporous structure were maintained in the VO_x/TiO₂ catalyst with a monolayer dispersion of V₂O₅, however, the surface area decreased to 126 m² g⁻¹. The catalyst was highly active and selective for methanol oxidation, giving about 55% conversion of methanol and 85% selectivity to dimethoxymethane at 423 K.     

Structural colors from TiO2/SiO2 multilayer flakes prepared by sol-gel process

Preparation of TiO₂/SiO₂ multilayer flakes and their application to decorative powders were investigated. In contrast to conventional products prepared through the multicoating of core platelets, the coreless TiO₂/SiO₂ multilayer flakes were prepared by detaching multilayer films from their substrates. These flakes exhibited structural colors, when the optical path length of both the TiO₂ and SiO₂ layers are adjusted to be one fourth of the wavelength of visible light. A multicoating of more than five layers resulted in the propagation of cracks, which prevented the preparation of thick flakes. Paint films fabricated using the multilayer flakes and acrylic resins showed reflectance spectra that were comparable with those obtained for multicoatings on substrates.     

Dielectric properties and microstructures of CaSiO3 ceramics with B2O3 addition

The effects of B₂O₃ additives on the sintering behavior, microstructure and dielectric properties of CaSiO₃ ceramics have been investigated. The B₂O₃ addition resulted in the emergence of CaO–B₂O₃–SiO₂ glass phase, which was advantageous to lower the synthesis temperature of CaSiO₃ crystal phase, and could effectively lower the densification temperature of CaSiO₃ ceramic to as low as 1100 °C. The 6 wt% B₂O₃-doped CaSiO₃ ceramic sintered at 1100 °C possessed good dielectric properties: _r = 6.84 and tan δ = 6.9 × 10⁻⁴ (1 MHz).     

Catalytic reduction of NH4NO3 by NO: Effects of solid acids and implications for low temperature DeNOx processes

Ammonium nitrate is thermally stable below 250 °C and could potentially deactivate low temperature NO_x reduction catalysts by blocking active sites. It is shown that NO reduces neat NH₄NO₃ above its 170 °C melting point, while acidic solids catalyze this reaction even at temperatures below 100 °C. NO₂, a product of the reduction, can dimerize and then dissociate in molten NH₄NO₃ to NO⁺ + NO₃⁻, and may be stabilized within the melt as either an adduct or as HNO₂ formed from the hydrolysis of NO⁺ or N₂O₄. The other product of reduction, NH₄NO₂, readily decomposes at ≤100 °C to N₂ and H₂O, the desired end products of DeNO_x catalysis. A mechanism for the acid catalyzed reduction of NH₄NO₃ by NO is proposed, with HNO₃ as an intermediate. These findings indicate that the use of acidic catalysts or promoters in DeNO_x systems could help mitigate catalyst deactivation at low operating temperatures (<150 °C).     

Preparation and electrochemical capacitance of RuO2/TiO2 nanotubes composites

In this paper, RuO₂/TiO₂ nanotubes composites were synthesized by loading various amounts of RuO₂ on TiO₂ nanotubes. The symmetric supercapacitors based on these nanocomposites were fabricated by using gel polymer PVA-H₃PO₄-H₂O as electrolyte. The electrochemical capacitance performance of the nanocomposites in these supercapacitors was investigated by current-potential responses, galvanostatic charge-discharge tests and electrochemical impedance spectroscopy. The results show that the three dimensional nanotube network of TiO₂ offers a solid support structure for active materials RuO₂, allows the active material to be readily accessible (available) for electrochemical reactions, and improves the efficiency of the active materials. A maximum specific capacitance of 1263 F/g was obtained for the RuO₂ which was loading on TiO₂ nanotubes.     

Nb2O5 as efficient and recyclable photocatalyst for indigo carmine degradation

Heterogeneous photocatalysis is a significant green technology for application in water purification. The application of Nb₂O₅ catalyst for the photodegradation of contaminants is few reported in the literature. Thus, the Nb₂O₅ catalyst was characterized by SEM, FTIR, surface area and charge surface density. This catalyst was applied to degrade indigo carmine dye, which was compared with degradation catalyzed by TiO₂ and ZnO. Almost 100% of dye degradation occurred at 20, 45 and 90 min for TiO₂, ZnO and Nb₂O₅, respectively. The effect of Nb₂O₅ catalyst concentration, pH and ionic strength (μ) was investigated. The Nb₂O₅ activity increased at 0.7 g/L and for higher catalyst concentrations the degradation was kept constant. Degradation of indigo carmine dye catalyzed by Nb₂O₅ was improved at pH < 4.0 and μ = 0.05 mol/L. TiO₂, ZnO and Nb₂O₅ were recovered and re-applied in other nine reaction cycles. While TiO₂ and ZnO have an abrupt loss of their catalytic activity, Nb₂O₅ maintained 85% of catalytic activity after 10 reaction cycles.     

Synthesis and reaction mechanism of Ti3SiC2 ternary compound by carbothermal reduction of TiO2 and SiO2 powder mixtures

The present study aims to investigate synthesis of Ti₃SiC₂ from TiO₂ and SiO₂ powder mixtures by carbothermal reduction method. Equilibrium TiO₂–SiO₂–C ternary phase diagram was used to predict the conditions for the formation of Ti₃SiC₂ at 1800 K under Ar atmosphere. A reactant mixture with a TiO₂:SiO₂ molar ratio of 1.5 and a C content of 68.75 mol% (26.86 wt%) was initially selected among the thermodynamically favorable reactant compositions for the experimental studies. Two different C sources, graphite flakes and pyrolytic C coating, were used to synthesize Ti₃SiC₂ at 1800 K under Ar atmosphere. When graphite flakes were used, the products contained a trace amount of Ti₃SiC₂ phase along with major TiC and minor SiC phases. Whereas, pyrolytic C coating on the oxide particles resulted in the products with much higher Ti₃SiC₂ contents owing to the close contact between the reactants. Optimal C concentration for the C coated oxide mixtures with a TiO₂:SiO₂ molar ratio of 1.5 was determined to be 30.05 wt% under the experimental conditions studied. Ti₃SiC₂ content of the products obtained from this reactant was observed to increase with reaction time to 31 wt% at 75 min beyond which it gradually decreased. XRD studies indicated that the product with the highest ternary carbide content also contained TiC and a trace amount of SiC. SEM-EDS analyses showed that this sample essentially consisted of spherical fine TiC particles and Ti₃SiC₂ nanolaminates. Equilibrium thermodynamic analysis of the TiO₂–SiO₂–C system suggested that the reaction of solid Ti₂O₃ with SiO and CO gases may play a dominant role in the formation of Ti₃SiC₂.