PP-g-MAH增容PP/PA 6的形态结构与流变性能

研究了用马来酸酐接枝聚丙烯（PP-g-MAH)来增容聚丙烯/聚酰胺6（PP/PA6）共混物的形态结构，探讨了PP-g-MAH增容PP/P6共混物的流动行为。结果表明，PP/PA6共混物为热力学不相容的海岛型两相结构，PP-g-MAH的加入改善了PA6与P宾相容性，使两相分散均匀。用PP-g-MAH为增容剂增容PP/PA6共混物，在加工成型温度下为非牛顿流体，在PP-g-MAH质量分数为10%，PP/PA6的配比为95：5-75：25，其流动行为可用T=1580γw^0.65模型描述。     

PP-g-MAH增容PP/玻纤增强PA6共混体系流变性能研究

采用毛细管流变仪,以聚丙烯接枝马来酸酐(PP-g-MAH)为增容剂,研究了PP-g-MAH对PP/玻纤增强聚酰胺6(PA6)共混体系流变性能的影响。结果表明:PP/玻纤增强PA6共混体系为典型的切力变型流体,共混体系的表观黏度均随着剪切速率的增大而降低;随增容剂用量的增加,共混体系的表观黏度提高,非牛顿指数n先增大后减小,黏流活化能ΔEη和结构黏度指数Δη先减小后增大;增容剂用量为5%时,共混体系的非牛顿指数出现极大值,黏流活化能和结构黏度指数出现极小值。     

PP-g-MAH和PP-g-GMA增容PP/PA6共混体系的研究

将自制的PP—g—MAH（聚丙烯接枝马来酸酐）及PP—g—GMA（聚丙烯接枝甲基丙烯酸缩水甘油酯）作为PP／PA6共混体系的相容剂，研究了加入聚丙烯接枝物后PP，PA6塑料合金的各种力学性能及形态结构。结果表明：在PP／PA6共混物中加入PP—g—MAH后，共混物的力学性能得到明显的提高．添加PP—g—MAH对不同比例PP／PA6共混物力学性能的影响不同；用PP—g—MAH和PP—g—GMA两种接枝物共同作为相容剂加入到PP／PA6共混物中比单独使用一种的效果要好。共混物的SEM照片表明。PP—g—MAH是PP／PA6共混物的有效增容剂。     

PP-g-MAH对PP/PA6共混物的增容作用

采用熔融接枝法,考察了单体和引发剂用量对聚丙烯(PP)/马来酸酐(MAH)接枝物接枝率的影响。将PP-g-MAH作为PP/尼龙6(PA6)共混物的增容剂,并利用SEM、XRD、DSC-TGA和万能试验机等测试手段对PP-g-MAH增容改性PP/PA6共混体系进行了研究。结果表明,PP-g-MAH接枝物对PP/PA6共混物具有良好的增容效果,PP结晶得到细化,共混物的力学性能和耐高温性能得到改善。     

PP-g-DBM增容PP/PA6共混物的性能研究

采用ＰＰ－ｇ－ＤＢＭ增容ＰＰ／ＰＡ６共混物,研究了增容共混物的力学性能和流变行为。结果表明,ＰＰ－ｇ－ＤＢＭ能改善ＰＰ／ＰＡ６共混物的相容性,显著提高共混物的力学性能;增容共混物的假塑性行为变强,粘流活化能增加熔体流动速率下降。     

聚丙烯接枝马来酸酐增容聚酰胺6／聚丙烯体系吸湿性能及力学性能的研究

以聚丙烯接枝马来酸酐(PP-g-MAH)为相容剂，利用其与聚酰胺6(PA6)在共混过程中的反应增容作用，实现了与聚丙烯(PP)之间的相容性共混，改变其用量，制备了系列具有不同组成的PA6／PP合金，研究了不同组成合金材料的吸湿性能及其在干态和充分吸湿状态时的冲击强度和拉伸性能。结果表明，向PA6／PP合金体系中加入相容剂PP-g-MAH后，可以改善合金的相界面，形成相容性的合金结构，明显降低合金材料的吸湿量及吸湿速率，但进一步增大相容剂PP-g-MAH的用量时，只能明显降低合金材料吸湿过程初期的吸湿速率，不能进一步显著降低合金材料的吸湿量。在相容剂PP-g-MAH用量一定时，随着PA6／PP合金体系中PA6组分含量的提高，合金在干、湿态条件下的冲击强度、拉伸强度、断裂伸长率均呈近似线性变化。对于具有相同基本组成的合金，随着相容剂PP-g-MAFI用量的增加，材料在干、湿态条件下的拉伸强度均有提高，杨氏模量则在干态时有所提高，在湿态时影响不显著，在干、湿态时断裂伸长率以及冲击强度均没有产生显著影响。     

弹性体接枝马来酸酐对PP/PA6 的增容作用

以4种弹性体接枝马来酸酐(MAH)共聚物作为聚丙烯/聚酰胺6(PP/PA6)共混体系的增容剂,从界面相互作用、形态结构和力学性能等方面比较了它们的增容作用。乙烯-辛烯共聚物接枝马来酸酐(POE-g-MAH)和乙丙三元共聚物接枝MAH(EPDM-g-MAH)使PP与PA6两相间的界面相互作用增强,增容效果较好;POE-g-MAH为增容剂时,PA6粒子分布较均匀,粒径约为1μm。POE-g-MAH能明显改善PP/PA6共混体系的韧性和强度,具有良好的增容作用。当w(POE-g-MAH)为10%时,w(PA6)为60%的共混体系拉伸强度最高,达到53.4MPa;适当增加PA6用量,可明显改善共混体系的流动性。     

PA6/PP合金的研制

以马来酸酐接枝聚丙烯(PP-g-MAH)为增容剂,制备了PA6/PP合金,研究了PA6/PP配比及PP-g-MAH用量对PA6/PP合金性能的影响。结果表明,加入一定量的PP-g-MAH能有效地改善PA6与PP之间的相容性,提高合金材料的各项性能指标。当PP-g-MAH用量为4份时,合金的力学性能最好;SEM分析显示,未加入PP-g-MAH时,PP在PA6基体中的分散不均匀、粒径大,当加入适量(4份)的PP-g-MAH时,PP在PA6中分散比较均匀,粒径尺寸明显减小;在PA6/PP(80/20)体系中加入4份PP-g-MAH制得合金的吸水率约为PA6的15%,缺口冲击强度分别比PA6、PP提高了72%和109%,热变形温度分别比PA6、PP提高了12℃和5.5℃。     

界面作用对PP/PA6共混体系相结构与力学性能的影响

研究了两种相容剂马来酸酐接枝聚丙烯(PP-g-MAH)、马来酸酐接枝乙烯-辛烯共聚物弹性体(POE-g-MAH)对聚丙烯/尼龙6(PP/PA6)共混体系力学性能的影响.通过扫描电子显微镜(SEM)、差示扫描量热仪(DSC)分析和力学性能测试,研究了相容剂POE-g-MAH和PP-g-MAH对PP/PA6共混物相容性、形态结构和力学性能的影响.研究结果表明:两种相容剂的加入都使PP/PA6体系的相容性增加,但PP-g-MAH的加入主要表现为增强效果,而POE-g-MAH的加入主要表现为增韧效果.     

相容剂对PP/PA6复合材料力学性能的影响

研究了2种相容荆PP—g-MAH（马来酸酐接枝聚丙烯）、POE—g—MAH（马来酸酐接枝乙烯辛烯共聚物）对PP／PA6（聚丙烯／聚酰胺6）共混体系力学性能的影响。研究结果表明，2种相容荆的加入都使PP／PA6体系的相容性增加，但PP—g—MAH的加入主要表现为增强效果，而POE-g-MAH的加入主要表现为增韧效果。     

Effects of compatibilization of oxidized polypropylene on PP blends of PP/PA6 and PP/talc

The influence of compatibilization on the dynamic mechanical properties of polypropylene (PP) binary blends with polyamide‐6 (PA6), Talc, and oxidized PP (OPP) was investigated. The oxidation of PP homopolymer was performed in a internal mixer by using air as a oxidizing agent (under atmospheric pressure) and dodecanol‐1 as an accelerator at 180°C for 6½ h [Abdouss, M.; Sharifi‐Sanjani, N.; Bataille, P. J Appl Polym Sci 1999, 36, 10]. In the blends, OPP was used as a blend component and compared with PP over the whole concentration range. Pressed film blends of PP/OPP, PP/OPP/Talc, and PP/OPP/PA6 were examined by dynamic mechanical analyzer, thermal gravimetry analysis, and scanning electron microscopy. Mechanical properties such as tensile strength, modulus of elasticity, elongation, melt flow index, and hardness of the blends were measured. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 2871–2883, 2004     

原位增容对反应挤出制备HDPE/PA6合金的影响

高密度聚乙烯(HDPE)/聚酰胺6(PA 6)合金挤出过程中的原位增容是通过马来酸酐(MAH)接枝HDPE(HDPE-g-MAH)引发己内酰胺(CL)聚合生成PA 6接枝HDPE(HDPE-g-PA 6)来实现的。通过改变HDPE-g-MAH含量,研究HDPE/PA 6合金反应挤出制备过程中,原位增容对合金的单体转化率和性能的影响。通过对合金中接枝物的提取和表征,可以确定在反应挤出过程中原位生成了接枝物HDPE-g-PA 6。通过场发射扫描电子显微镜和流变性能分析可知,随着HDPE-g-MAH含量增加,HDPE/PA 6合金中PA 6的尺寸减小,尺寸分布变窄;增加HDPE-g-MAH含量,原位生成的增容剂HDPE-g-PA 6数量增多,从而增强了界面结合力,改善了合金的相容性。     

Dynamic rheological properties of binary PP/PA and ternary PP/PA/GF blends

The dynamic rheological behavior was investigated for binary polypropylene (PP) - polyamide-6 (PA-6) and ternary PP-PA-6-glass fiber (GF) blends. The observed trends are related to the blend morphology and the partitioning of the GF within the three component blends. The dynamic and shear viscosity results show a good overlap for the PP homopolymer, within the shear rates studied. The addition of PA-6 and/or glass fibers to the PP causes significant deviations between the two rheological behaviors. This reflects the fibrillation of PA-6 and the orientation of glass fibers during shear rheometry, which reduce the blends' shear viscosity. The effect of PA-6 content on dynamic viscosity is less significant than for shear viscosity, owing to the absence of morphological structuring. The addition of PA-6 to PP increased the principal relaxation time of the binary blends. The addition of GF to these binary blends gave a further increase in the principal relaxation time.     

Morphology,thermal behavior,and mechanical properties of PA1010/PP and PA 1010/PP-g-GMA blends

The modification of polypropylene (PP) was accomplished by melt grafting glycidyl methacrylate (GMA) on its molecular chains. The resulting PP-g-GMA was used to prepare binary blends of polyamide 1010 (PA1010) and PP-g-GMA. Different blend morphologies were observed by scanning electron microscopy (SEM) according to the nature and content of PA1010 used. Comparing the PA1010/PP-g-GMA and PA1010/PP binary blends, the size of the domains of PP-g-GMA were much smaller than that of PP at the same compositions. It was found that mechanical properties of PA1010/PP-g-GMA blends were obviously better than that of PA1010/PP blends, and the mechanical properties were significantly influenced by wetting conditions for uncompatibilized and compatibilized blends. A different dependence of the flexural modulus on water was found for PA1010/PP and PA1010/PP-g-GMA. These behaviors could be attributed to the chemical interactions between the two components and good dispersion in PA1010/PP-g-GMA blends. Thermal and rheological analyses were performed to confirm the possible chemical reactions taking place during the blending process. © 1997 John Wiley & Sons, Inc. J Appl Polym Sci 64: 1489–1498, 1997     

PA 6/EPDM-g-MAH/HDPE三元共混物的形态与力学性能

制备了聚酰胺(PA)6/马来酸酐(MAH)接枝三元乙丙橡胶(EPDM)(EPDM-g-MAH)/高密度聚乙烯(HDPE)三元共混物,采用扫描电子显微镜观察了三元共混物的相形态,研究了注塑过程的二次剪切流动对该三元共混物相形态的影响,以及三元共混物相形态对其力学性能的影响。结果表明:二次剪切流动有利于PA 6/EPDM-g-MAH/HDPE体系向热力学最稳定的壳核结构发生转变。与PA 6/EPDM-g-MAH二元共混物相比,该三元共混物的力学性能得到较大改善,w(EPDM-g-MAH)为15%时,其Izod缺口冲击强度达85.83 kJ/m2,是纯PA 6的9倍,是同等橡胶含量的PA 6/EPDM-g-MAH二元共混物的2倍。     

Phase morphology and stability of co-continuous (PPE/PS)/PA6 and PS/PA6 blends: effect of rheology and reactive compatibilization

(PPE/PS)/PA6 and PS/PA6 blends were prepared by means of melt-extrusion. They were compatibilized using the reactive styrene-maleic anhydride copolymer with 2 wt% maleic anhydride (SMA2). The effect of compatibilization on the phase inversion and the stability of the resulting co-continuous blend structures were investigated using scanning electron microscopy, dissolution and extraction experiments. The onset of co-continuity shifted towards lower PA6 concentrations according to the change in blend viscosity ratio. The melting order of the components inside the extruder could result in a change in the observed co-continuity interval in slowly developing phase morphologies. The unmodified co-continuous blends were not stable and did break-up into a droplet/matrix type of morphology upon annealing in the melt depending on the blend composition. Although the stability of the threads during annealing improved upon compatibilization because of the lower resulting interfacial tension, the decreased possibility for recombination and coalescence during flow reduced the co-continuous region for the compatibilized blends. It is proposed that a dynamic equilibrium between break-up and recombination phenomena after the initial network formation is necessary to maintain the network structure.     

Improvement of mechanical properties for PP/PS blends by in situ compatibilization

The effect of the in situ compatibilization on the mechanical properties of PP/PS blends was investigated. The application of Friedel-Crafts alkylation reaction to the PP/PS-blend compatibilization was assessed. Styrene/AlCl₃ was used as catalyst system. The graft copolymer (PP-g-PS) formed at the interphase showed relatively high emulsifying strength. Scission reactions, occurring in parallel with grafting, were verified for PP and PS at high catalyst concentration, but no crosslinking reactions were detected. Tensile tests were performed on dog-bone specimens of the blends. Both elongation at break and toughness increased with catalyst concentration. At 0.7% AlCl₃, a maximum was reached, which amounted to five times the value of the property for the uncompatibilized blend. At higher catalyst concentrations these properties decreased along with the PP molecular weight due to chain-scission reactions. On the other hand, the tensile strength did not change with the catalyst concentration. The in situ compatibilized blends showed considerable improvement in mechanical properties, but were adversely affected by chain scissions at high catalyst contents.     

Effect of compatibilization on the properties of HIPS/PA1010 blends

Blends consisting of high‐impact polystyrene (HIPS) as the matrix and polyamide 1010 (PA1010) as the dispersed phase were prepared by mixing. The grafting copolymers of HIPS and maleic anhydride (MA), the compatibilizer precursors of the blends, were synthesized. The contents of the MA in the grafting copolymers are 4.7 wt % and 1.6 wt %, and were assigned as HAM and LMA, respectively. Different blend morphologies were observed by scanning electron microscopy (SEM); the domain size of the PA1010 dispersed phase in the HIPS matrix of compatibilized blends decreased comparing with that of uncompatibilized blends. For the blend with 25 wt % HIPS‐g‐MA component, the T_c of PA1010 shifts towards lower temperature, from 178 to 83°C. It is found that HIPS‐g‐MA used as the third component has profound effect on the mechanical properties of the resulting blends. This behavior has been attributed to the chemical reaction taking place in situ during the mixing between the two components of PA1010 and HIPS‐g‐MA. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 76: 799–806, 2000     

Effect of reactive compatibilisation on the phase morphology and tensile properties of PA12/PP blends

Both uncompatibilized and compatibilized blends based on polyamide 12 (PA12) and isotactic polypropylene (PP) were prepared in a Brabender Plastograph®. The compatibiliser used was maleic anhydride functionalized polypropylene (PP‐g‐MA). Phase morphology of the blends was inspected in scanning electron microscope (SEM) on cryogenically fractured etched surfaces of the specimens. PA12/PP blends possessed a nonuniform and unstable morphology owing to the incompatibility between their constituents. Addition of compatibiliser improved the interfacial characteristics of the blends by retarding the rate of coalescence. So, the phase morphology became more fine, uniform, and stable. Tensile properties of both uncompatibilized and compatibilized blends were measured as a function of blend composition and compatibiliser concentration. Uncompatibilized blends displayed inferior mechanical properties to compatibilized ones; especially for those containing 40–60 wt % of PP. Reactive compatibilisation of blends was found to be efficient and improved the tensile strength of the blends considerably. Addition of PP‐g‐MA improved the interfacial adhesion, decreased the interfacial tension, and thereby, enhanced the tensile strength by 85%. Finally, various models were adopted to describe the tensile strength of the blends. The experimental data exhibited a reasonably good fit with Nielsen's first power law model. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci, 2006     

PP-g-MAH增容PP/PA 6体系的分形理论分析

利用分形理论分析了聚丙烯(PP)与聚酰胺(PA) 6(质量比为80 : 20)增容共混体系.结果表明,马来酸酐接枝聚丙烯(PP-g-MAH)用量对体系分散相(PA 6)形状复杂程度的影响符合分形理论的无标度性(标度定律).在PP/PA 6增容共混体系中,分散相粒径在一定程度上随PP-g-MAH用量的增大而逐渐减小且形状趋于复杂化;分散相粒子分维数小于0.38时,提高分散相的形状复杂程度对提高材料力学性能有利.