Synthesis,photo‐, and electroluminescent properties of the soluble poly[(2,5‐diphenylene‐1,3,4‐oxadiazole)‐ 4,4′‐vinylene]

A novel soluble conjugated polymer, poly[(2,5‐diphenylene‐1,3,4‐oxadiazole)‐4,4′‐vinylene] (O‐PPV), containing an electron‐transporting group on the main chain of PPV, was synthesized according to HORNER mechanism. The oligo‐polymer with M_w = 1000 and T_d = 270°C is soluble in chloroform and tetrahydrofuran. The photoluminescent (PL) properties were investigated using different concentrations of solid‐state O‐PPV/PEO blends absorption and selective excitation measurements. The results show that PL arises from interchain charge‐transfer states in solid‐state O‐PPV. Compared with the analogous single‐layer device constructed with PPV (ITO/PPV/Al), which emits two peaks at λ = 520 nm and 550 nm (shoulder), the electroluminescence (EL) spectrum of the device [ITO/O‐PPV (80 nm)/Al] is a broad peak at λ_max = 509 nm. The quantum efficiency (0.13%) of the device ITO/O‐PPV/Al is much higher than that of the device ITO/PPV/Al, due to the introduction of the electron‐transporting group–oxadiazole units in the main chain of PPV. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 74: 3535–3540, 1999     

Effect of layer thickness on the electrical parameters and conduction mechanisms of conjugated polymer‐based heterojunction diode

In this study, thickness‐dependent current density–voltage (J–V) characteristics obtained for poly{(9,9‐dioctylfluorene)?2,7‐diyl‐(4,7‐bis(thien‐2‐yl) 2‐dodecyl‐benzo[1,2,3] triazole)} (PFTBT) conjugated copolymer based heterojunction diode fabricated on ITO were investigated in terms of electrical characteristics. In order to analyze J –V plots with ITO/PEDOT:PSS/PFTBT:PC₆₁BM/LiF/Al configuration, the thickness‐dependent J–V measurements were applied in the thickness range between 90 and 200 nm. The effect of PFTBT:PC₆₁BM layer thickness on the forward J –V characteristics were investigated by evaluating electrical parameters such as zero bias barrier height (Φ_Bo), ideality factor (n ), shunt resistance (R _sh), series resistance (R_s ), the interface states density (N _ss), and space‐charge limited mobility. The results show that at PFTBT:PC₆₁BM layer thickness of 90 and 200 nm, ideality factor for ITO/PEDOT:PSS/PFTBT:PC₆₁BM/LiF/Al heterojunction diodes ranged from 2.726 to 3.121 and the thermionic emission over the heterojunction diodes is crucial at low current densities and the intrinsic thermally generated charge carriers controlled the forward current this region of the heterojunction diode. At relatively higher voltage, the current mechanism of ITO/PFTBT:PC₆₁BM/PEDOT:PSS/LiF/Al heterojunction diodes were found to obey a space charge limited (SCLC) conduction mechanism. The values of N_ss and R_s in heterojunction diodes increase with increasing PFTBT:PC₆₁BM layer thickness and effect the main electrical parameters of diodes. In addition, the leakage current of heterojunction diodes are taken and interpreted via Poole‐Frenkel emission and Schottky emission. The leakage current was controlled in ITO/PEDOT:PSS/PFTBT:PC₆₁BM/LiF/Al heterojunction diodes by Poole‐Frenkel emission above 140 nm and by Schottky emission under 140 nm. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134 , 44817.     

Resistive switching characteristics of polyimides derived from 2,2′‐aryl substituents tetracarboxylic dianhydrides

2,2′‐Position aryl‐substituted tetracarboxylic dianhydrides including 2,2′‐bis(biphenyl)‐4,4′,5,5′‐biphenyl tetracarboxylic dianhydride and 2,2′‐bis[4‐(naphthalen‐1‐yl)phenyl)]‐4,4′,5,5′‐biphenyl tetracarboxylic dianhydride were synthesized. A new series of aromatic polyimides (PIs) were synthesized via a two‐step procedure from 3,3′,4,4′‐biphenyl tetracarboxylic dianhydride and the newly synthesized tetracarboxylic dianhydrides monomers reacting with 2,2′‐bis[4′‐(3″,4″,5″‐trifluorophenyl)phenyl]‐4,4′‐biphenyl diamine. The resulting polymers exhibited excellent organosolubility and thermal properties associated with T_g at 264 °C and high initial thermal decomposition temperatures (T_5%) exceeding 500 °C in argon. Moreover, the fabricated sandwich structured memory devices of Al/PI‐a/ITO was determined to present a flash‐type memory behaviour, while Al/PI‐b/ITO and Al/PI‐c/ITO exhibited write‐once read‐many‐times memory capability with different threshold voltages. In addition, Al/polymer/ITO devices showed high stability under a constant stress or continuous read pulse voltage of ? 1.0 V. Copyright © 2011 Society of Chemical Industry     

Electrical characterization of the boron trifluoride doped poly(3‐aminoacetophenone)/p‐Si junction

Electrical and interface state properties of the borontrifluoride doped poly(3‐aminoacetophenone)/p‐Si junction have been investigated by current‐voltage and impedance spectroscopy methods. Al/p‐Si/P₃APBF₃/Aldiode indicates a nonideal behavior with electrical parameters (n = 3.53, ?_B = 0.82 eV, and R_s = 1.48 kΩ), which result from the interfacial layer, series resistance, and resistance of the organic semiconductor. The obtained barrier height value of the Al/p‐Si/P₃APBF₃/Aldiode is higher than that of the conventional Al/p‐Si (?_B = 0.58 eV) Schottky diode. The interface state density of the diode was of the order of 1.05× 10¹² eV^?1 cm^?2. It is evaluated that the barrier height and interface state density values of the diode are modified using the boron trifluoride doped poly (3‐aminoacetophenone) organic semiconductor. POLYM. ENG. SCI., 2010. © 2009 Society of Plastics Engineers     

Highly transparent and organosoluble polyimides derived from 2,2′‐disubstituted‐4,4′‐oxydianilines

Polypyrrole (PPy) and Polypyrrole‐ZnO (PPy‐ZnO) nanocomposites were electrodeposited on mild steel and its corrosion protection ability was studied by Tafel and Impedance techniques in 3.5% NaCl solution. Pure Polypyrrole film was not found to protect the mild steel perfectly but the coating with nano‐sized ZnO (PPy‐ZnO) has dramatically increased the corrosion resistance of mild steel. Electrochemical Impedance Spectroscopy (EIS) measurements indicated that the coating resistance (R_coat) and corrosion resistance (R_corr) values for the PPy‐ZnO nanocomposite coating was much higher than that of pure PPy coated electrode. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Preparation of organo‐soluble poly[(2,2′‐m‐phenylene)‐5,5′‐bibenzimidazole] with high yield by homogeneous nitration reaction

To prepare organo‐soluble poly[(2,2,′‐m‐phenylene)‐5,5′‐bibenzimidazole] (PBI) with high yield, a homogeneous nitration of PBI was attempted. Nitro‐substituted PBI (NO₂‐PBI) was synthesized through the homogeneous reaction of the PBI powder with nitric acid in sulfuric acid. The degree of substitution (DS) of this NO₂‐PBI is higher than that of the NO₂‐PBI prepared through the heterogeneous reaction of the PBI fiber. The viscosity of the NO₂‐PBI prepared through the homogeneous reaction decreased with increasing amount of nitric acid added. The DS of the NO₂‐PBI reached the maximum value of 2. The substitution efficiency of nitro groups decreased as the amount of nitric acid added increased. When a small quantity of nitric acid was added, the substitution of the sulfonic acid group was confirmed as well as that of the nitro group. The solubility of the NO₂‐PBI depended strongly on the DS. The NO₂‐PBI having the DS of about 2 was completely soluble in dimethylacetamide and almost soluble in N‐methylpyrrolidone. At an elevated temperature, it was also soluble in other polar aprotic solvents such as dimethylformamide and dimethylsulfoxide. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 78: 438–445, 2000     

N‐Oligo(3‐hydroxybutyrate)‐functionalized polypyrroles: towards bio‐erodible conducting copolymers

New copolymer materials have been prepared by chemical grafting of oligomeric 3‐hydroxybutyric acid (OHB) onto polypyrrole (PPy) derivatives. The influence of grafting density and molecular weight of OHB brushes on the physicochemical properties of prepared copolymers was investigated. PPy substrates were prepared by FeCl₃‐driven oxidative homopolymerization of N‐(2‐carboxyethyl)pyrrole or its copolymerization with pyrrole. The grafting method employed involved controlled anionic polymerization of β‐butyrolactone on pyrrole‐tethered potassium carboxylate active sites. Obtained PPy‐g‐OHB copolymers of varying grafting density and pendant polyester chain length were characterized and the observed structure–property relationships discussed. The impact of real time exposure to phosphate‐buffered saline environment was investigated and the residue products were characterized. Cross‐correlation of spectroscopic, thermal, electrical and elemental analysis data afforded comprehensive evaluation of the structure of prepared materials and their behaviour in hydrolytic medium. Erosion and degradation pathways have been identified, indicating ways to consciously tailor the physicochemical properties of these new biomimetic materials. © 2016 Society of Chemical Industry     

Synthesis and light‐emitting properties of a novel π‐conjugated poly[di(p‐phenyleneethynylene)‐alt‐ (p‐phenylenecyanovinylene)] containing n‐octyloxy side branches

A novel π‐conjugated poly[di(p‐phenyleneethynylene)‐alt‐(p‐phenylenecyanovinylene)] having n‐octyloxy side chains (PPE‐C₈PPE‐PPV) was prepared by polymerization of the monomer DEDB with BCN. Chemical structure of the polymer obtained was confirmed by ¹H NMR, FTIR, and EA. PPE‐C₈PPE‐PPV had a molecular weight enough to fabricate the electroluminescent (EL) device, and showed a good organosolubility, excellent thermal stability, and film‐forming property. In UV absorption and PL spectra in film it showed a maximum at 430 and 543 nm, respectively, which appeared 5 and 41 nm longer wavelengths than that of the solution, respectively. HOMO, LUMO energy levels and band gap were determined to be ?5.70, ?3.29, and 2.41 eV, respectively. Two EL devices with low‐work function cathodes were fabricated with the structures of ITO/PEDOT/PPE‐C₈PPE‐PPV/cathodes (LiF/Al and Mg:Ag/Ag). The both devices exhibited a bright green light emission at 545 nm and the maximum luminescence of 197 cd/cm² (LiF/Al) and 158 cd/cm² (Mg:Ag/Ag). © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Structural features and thermoelectric properties of Al‐doped (ZnO)5In2O3 homologous phases

In this work, we investigated the influence of Al doping on the structure of the (ZnO)₅In₂O₃ homologous phase and the thermoelectric characteristics of (ZnO)₅(In_1?xAl_x)₂O₃ ceramics for x=0, 0.01, 0.03, 0.05, 0.1, and 0.2, prepared using a classic ceramic procedure and sintering at 1500°C for 2 hours. The Al substituted for In on both the primary sites in the Zn₅(In_1?xAl_x)₂O₈ homologous phase, the octahedral sites in the basal‐plane inversion boundaries and the trigonal bi‐pyramidal sites in the zig‐zag inversion boundaries, which resulted in a uniformly increased shrinkage of the unit cell with the additions of Al. The a and c parameters were reduced for x=0.2 by a maximum 0.8%. All the samples had similar microstructures, so the differences in the TE characteristics mainly resulted from the effects of the substitution of Al for In, decreasing the charge‐carrier concentration and affecting their mobility. Slightly improved TE characteristics were only observed for Al additions with x=0.01‐0.05, while larger additions of Al only resulted in a reduced electrical conductivity and decreased ZT values in comparison to the un‐doped composition.     

CuBr2‐induced charge screening on photoactive nanocolloidal polypyrrole:poly(styrene sulfonate) composite multilayer thin‐film counter electrodes for high‐efficiency dye‐sensitized solar cells

Nanocolloidal polypyrrole (PPy):poly(styrene sulfonate) (PSS) particles were synthesized by chemical oxidative polymerization using 15 wt% of PSS. The highly processable polymer composite (PPy:PSS) was spin‐coated at 4000 rpm on fluorine‐doped tin oxide glass and subsequently employed as a counter electrode (CE) for dye‐sensitized solar cells (DSCs). PPy:PSS multilayer (one, three, five) CEs were treated with CuBr₂ salt, which enhances the efficiency of the DSCs. Optical studies reveal that a bulkier counterion hinders interchain interactions of PPy which on salt treatment shows a moderate redshift in absorption maxima. Salt‐treated PPy:PSS films exhibit lower charge transfer resistance, higher surface roughness and better catalytic performance for the reduction of I₃^?, when compared with untreated films. The improved catalytic performance of salt‐treated PPy:PSS multilayer films is attributed to charge screening and conformational change of PPy, along with the removal of excess PSS. Under standard AM 1.5 sunlight illumination, salt treatment is shown to boost the efficiency of multilayer PPy:PSS composite film‐based DSCs, leading to enhanced power conversion efficiency of 6.18, 6.33 and 6.37% for one, three and five layers, respectively. These values are significantly higher (ca 50%) than those for corresponding devices without CuBr₂ salt treatment (3.48, 2.90 and 2.01%, respectively). © 2016 Society of Chemical Industry     

Effects of solution processing on the photovoltaic response of poly(n‐vinyl carbazole) films

The effects of solution processing on the photovoltaic response of poly(n‐vinyl carbazole) (PVK) films were investigated. PVK films were formed by spincasting onto glass coated with indium tin oxide (ITO) and poly(3,4‐ethylenedioxythiophene) (PEDOT)–polystyrenesulfonate (PSS). Some of the PVK films were redissolved in chlorobenzene and redried in the absence or presence of an electric field. Illuminated current–voltage characteristics were measured for an ITO/PEDOT:PSS/PVK/Ca:Al device. Films spincast from a 50 mg/mL solution, redissolved, and dried in the absence of the electric field exhibited a 26% higher charge collection efficiency than films dried in the presence of the electric field. The increased charge collection efficiency was attributed to changes in the molecular configuration of the PVK films. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Investigations of the electrical conduction mechanisms of polyaniline‐DBSA/poly(acrylonitrile‐butadiene styrene) blends

The electrical properties of Al/PANI‐DBSA/ABS/Au blend with PANI (5%) w/w have been investigated by using of current‐voltage (I‐V) measurements, in a temperature range of 100–313 K. The analysis of I‐V characteristics in the forward direction was based on thermionic emission mechanism for applied electrical field till ～3 × 10² V/cm. The thickness dependence of the current‐voltage relationship, clearly demonstrates that the electrical current for larger fields is space charge limited current (SCLC). Temperature dependences of the ideality factor, barrier height, and series resistance have been calculated. The mobility of carriers which is temperature dependent was calculated using the trap free SCLC as 1.53 × 10^?4 cm² V^?1 s^?1 at room temperature. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40688.     

Synthesis and characterization of the soluble fluorescent poly[2‐decyloxy‐5‐(2′‐(6′‐dodecyloxy)naphthyl)‐1,4‐phenylenevinylene]

A new soluble fluorescent polymer, poly[2‐decyloxy‐5‐(2′‐(6′‐dodecyl‐oxy)naphthyl)‐1,4‐phenylenevinylene] (DDN‐PPV), with no tolane‐bisbenzyl (TBB) structure defects is prepared by the dehydrohalogenation of 1,4‐bis(bromomethyl)‐2‐decyloxy‐5‐(2′‐(6′‐dodecyloxy)naphthyl)benzene (as monomer) in this study. The aforementioned monomer is synthesized via such chemical reactions as alkylation, bromination, and Suzuki coupling reactions. The structure and properties of the DDN‐PPV are examined by ¹H NMR, FTIR, UV/vis, TGA, photoluminescence (PL), and electroluminescence (EL) analyses. The two asymmetric decyloxy and 6′‐dodecyloxynaphthyl substituents on the phenylene ring make the DDN‐PPV soluble in organic solvents and eliminate the TBB structure defects. With the DDN‐PPV acting as a light‐emitting polymer, a device is fabricated with a sequential lamination of ITO/PEDOT/DDN‐PPV/Ca/Ag. The EL spectrum of the device shows a maximum emission at 538 nm. The turn on voltage of the device is about 16.6 V. Its maximum brightness is 14 cd/m² at a voltage of 18.2 V. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 103: 2734–2741, 2007     

New organic semiconductor materials: electrical conductivity,thermal properties and application of voltage‐controlled negative resistance device of poly[(2‐acrylamido‐2‐methyl‐1‐propanesulfonic acid)‐co‐(maleic acid)]

BACKGROUND: Electrical conductivity, photoconductivity, voltage‐controlled negative resistance and thermal properties of copolymers of 2‐acrylamido‐2‐methyl‐1‐propanesulfonic acid and maleic acid were investigated in order to obtain new organic semiconductors. RESULTS: The room temperature conductivity of three different copolymers was found to be in the range 1.28 × 10^?8 ? 1.20 × 10^?7 S cm^?1. The dark‐ and photo‐current‐voltage characteristics indicate that the copolymers exhibit voltage‐controlled differential negative resistance behaviour. The electrical conductivity of the polymers increases by photo‐illumination, suggesting that the polymers exhibit photoconductivity. The width of the exponential tail in the forbidden band gap of the three polymers was determined via the transient photocurrent technique and E₀ values were in the range 34.4–36.49 meV. CONCLUSION: The results suggest that the copolymers could be used as organic semiconductor materials. Copyright © 2007 Society of Chemical Industry     

Synthesis and characterization of poly(1,4‐phenylenevinylene) derivatives containing liquid crystalline oxadiazole groups

Two novel poly(1,4‐phenylenevinylene) (PPV) derivatives containing liquid crystalline oxadiazole side chains were prepared by a dehydrochlorination process. The homopolymer poly(2‐methoxy‐5‐((2‐methoxy‐phenyl)‐5‐hexyloxy‐phenyloxy‐1,3,4‐oxadiazole)‐1,4‐phenylenevinylene) (HO–PE₆) is insoluble in common solvents, whereas the copolymer poly(2‐methoxy‐5‐((2‐methoxy‐phenyl)‐5‐hexyloxy‐phenyloxy‐1,3,4‐oxadiazole))‐(2‐methoxy‐5‐(2′‐ethylhexyloxy))‐1,4‐phenylenevinylene) (CO–PE₆) is soluble in common solvents such as chloroform, THF, and p‐xylene. The molecular structure of CO–PE₆ was confirmed by FTIR, ¹H‐NMR, UV–vis spectroscopy, and polarized light microscopy. CO–PE₆ showed a maximum emission at 556 nm in chloroform and at 564 nm in solid film, when excited at 450 nm. The maximum electroluminescence emission of the device indium–tin oxide (ITO)CO–PE₆/Al is at 555 nm. The turn‐on voltage of LEDs based on CO–PE₆ and MEH–PPV is 6.5 and 8.5 V, respectively. The electron mobility of CO–PE₆ is higher than that of MEH–PPV based on the results of current–voltage and electrochemical behavior of both MEH–PPV and CO–PE₆. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 91: 396–403, 2004     

Electrical response of polypyrrole films doped with dodecylbenzene sulfonic acid to acetone vapor

Measurements of current‐voltage curves at room temperature, in nitrogen and nitrogen‐acetone atmospheres have clearly demonstrated the rectifying behavior of the Al/PPy‐DBSA/Au structure. For this structure, the values of 0.82 eV and 2.31, for the barrier height and ideality factor, respectively, have been obtained in nitrogen atmosphere, while at concentration of 120 ppm of acetone, the corresponding values were 0.74 eV and 2.07. The barrier height value obtained from I–V characteristic is lower than the barrier height value obtained from C‐V measurements. The discrepancy can be due to the existence of an interfacial oxide layer between the semiconductor and Schottky contact metal. The density distribution curves of the interface states vary in the range (0.55–E_V) to (0.84–E_V) for pure nitrogen, and (0.45–E_V) to (0.60–E_V) in atmosphere with acetone. The interface state density has an exponential rise with bias from the midgap towards the top of the valence band of the PPy‐DBSA. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Synthesis and light‐emitting properties of new poly(p‐phenylenevinylene) derivatives containing oxadiazole moiety

Two new poly(p‐phenylenevinylene) (PPV) derivatives containing oxadiazole moiety (OXA‐PPV1 and OXA‐PPV2) were synthesized by the Wittig condensation polymerization reaction. Their thermal and light‐emitting properties were investigated. The single‐ and triple‐layer electroluminescent (EL) devices with configurations of ITO/polymer/Al and ITO/polymer/OXD‐7/Alq₃/Al were fabricated. They exhibited blue emission at 470 nm for OXA‐PPV1 and green emission at 560 nm for OXA‐PPV2. The turn‐on voltages of triple‐layer device were 11 V for OXA‐PPV1 and 8 V for OXA‐PPV2. The triple‐layer EL devices showed much better performance than did the single‐layer devices. The spectra indicated energy transfer occurred from segments of side chain to polymer backbone. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 85: 422–428, 2002     

Greatly enhanced photocurrent in inorganic perovskite [KNbO3]0.9[BaNi0.5Nb0.5O3‐σ]0.1 ferroelectric thin‐film solar cell

Inorganic perovskite [KNbO₃]_0.9[BaNi_0.5Nb_0.5O_3‐σ]_0.1 (KBNNO) ferroelectric thin films with narrow band gap (1.83 eV) and high room‐temperature remnant polarization (Pr = 0.54 μC/cm²) was grown successfully on the Pt(111)/Ti/SiO₂/Si(100) substrates by pulsed laser deposition. Ferroelectric solar cells with a basic structure of ITO/KBNNO/Pt were further prepared based on these thin films, which exhibited obvious external‐poling dependent photovoltaic effects. When the devices were negatively poled, the short‐circuit current and open‐circuit voltage were both significantly higher than those of the devices poled positively. This is attributed to enhanced charge separation under the depolarization field induced by the negative poling, which is superimposed with the built‐in field induced by the Schottky barriers at the interfaces between KBNNO and the two electrodes. When a poling voltage of ‐1 V was applied, the device showed a short‐circuit current as high as 27.3 μA/cm², which was by two orders of magnitude larger than that of the KBNNO thick‐film (20 μm) devices reported previously. This work may inspire further exploration for lead‐free inorganic perovskite ferroelectric photovoltaic devices.     

Grain‐Boundary and Thermally Stimulated Current Characteristics of Y2O3‐Doped ZnO Varistor

The doping of rare‐earth oxides can greatly improve the electrical characteristics of ZnO varistors. Thermally stimulated current (TSC) characteristic test, capacitance voltage (C–V) characteristic test, scanning electron microscope (SEM) test, and voltage current (V–I) test were carried out to study the influence of Y₂O₃ content on the electrical properties of ZnO varistors in this study. The results show that the grain size decreases while the voltage gradient increases as the Y₂O₃ content is increased. The reaction of Y₂O₃ with other additives leads to the decrease in grain‐boundary defects, which accounts for the decrement of barrier height, donor density, and surface state density. The trap level and trapped charge of ZnO varistors decrease as the Y₂O₃ content is increased from 0.3 to 0.9 mol%, which means the shallow traps inside ZnO varistors reduce, and the Y₂O₃ additive can greatly improve the TSC characteristic of ZnO varistors.     

siRNA Modified with 2′‐Deoxy‐2′‐C‐methylpyrimidine Nucleosides

(2′S)‐2′‐Deoxy‐2′‐C‐methyluridine and (2′R)‐2′‐deoxy‐2′‐C‐methyluridine were incorporated in the 3′‐overhang region of the sense and antisense strands and in positions 2 and 5 of the seed region of siRNA duplexes directed against Renilla luciferase, whereas (2′S)‐2′‐deoxy‐2′‐C‐methylcytidine was incorporated in the 6‐position of the seed region of the same constructions. A dual luciferase reporter assay in transfected HeLa cells was used as a model system to measure the IC₅₀ values of 24 different modified duplexes. The best results were obtained by the substitution of one thymidine unit in the antisense 3′‐overhang region by (2′S)‐ or (2′R)‐2′‐deoxy‐2′‐C‐methyluridine, reducing IC₅₀ to half of the value observed for the natural control. The selectivity of the modified siRNA was measured, it being found that modifications in positions 5 and 6 of the seed region had a positive effect on the ON/OFF activity.