Investigation of water transport through membrane in a PEM fuel cell by water balance experiments

Water balance in a polymer electrolyte membrane fuel cell (PEMFC) was investigated by measurements of the net drag coefficient under various conditions. The effects of water balance in the PEMFC on the cell performance were also investigated at different operating conditions. Experimental results reveal that the net drag coefficient of water through the membrane depended on current density and humidification of feed gases. It was found that the net drag coefficient (net number of water molecules transported per proton) ranged from −0.02 to 0.93, and was dependent on the operating conditions, the current load and the level of humidification. It was also found that the humidity of both anode and cathode inlet gases had a significant effect on the fuel cell performance. The resistance of the working fuel cell showed that the membrane resistance increased as the feed gas relative humidity (RH) decreased. The diffusion of water across Nafion membranes was also investigated by experimental water flux measurements. The electro-osmotic drag coefficient was evaluated from the experimental results of water balance and diffusion water flux measurements. The value of electro-osmotic drag coefficient, ranging from 1.5 to 2.6 under various operating conditions, was in agreement with literature values. The electro-osmotic drag coefficient, the net flux of water through the membrane and the effective drag as a function of operating conditions will also provide validation data for the fuel cell modeling and simulation efforts.     

Humidity of reactant fuel on the cell performance of PEM fuel cell with baffle-blocked flow field designs

The objective of this work is to examine the effects of humidity of reactant fuel at the inlet on the detailed gas transport and cell performance of the PEM fuel cell with baffle-blocked flow field designs. It is expected that, due to the water management problem, the effects of inlet humidity of reactant fuel gases on both anode and cathode sides on the cell performance are considerable. In addition, the effects of baffle numbers on the detailed transport phenomena of the PEM fuel cell with baffle-blocked flow field are examined. Due to the blockage effects in the presence of the baffles, more fuel gas in the flow channel can be forced into the gas diffuser layer (GDL) and catalyst layer (CL) to enhance the chemical reactions and then augment the performance of the PEMFC systems. Effect of liquid water formation on the reactant gas transport is taken into account in the numerical modeling. Predictions show that the local transport of the reactant gas, the local current density generation and the cell performance can be enhanced by the presence of the baffles. Physical interpretation for the difference in the inlet relative humidity (RH) effects at high and low operating voltages is presented. Results reveal that, at low voltage conditions, the liquid water effect is especially significant and should be considered in the modeling. The cell performance can be enhanced at a higher inlet relative humidity, by which the occurrence of the mass transport loss can be delayed with the limiting current density raised considerably.     

Water transport in the proton-exchange-membrane fuel cell: measurements of the effective drag coefficient

The water transport in proton-exchange-membrane fuel cells has been experimentally investigated by measurements of the effective or net drag coefficient. Results are presented for a wide range of operating conditions (current density, temperature, pressure, stoichiometry and humidity of the inlet gases), as well as for different types of membrane-electrode-assemblies. It was found that the humidity and the stoichiometry of the inlet gases had a large effect on the drag. Of the material properties investigated, the membrane thickness was found to be the most significant parameter. Inspection of the cell performances showed that drying of the cathode was much more detrimental for the cell performance than drying of the anode. This was ascribed to increased activation losses, which turned out to be extremely sensitive to the type of cathode used.     

Numerical study on PEMFC’s geometrical parameters under different humidifying conditions

Steady-state and three-dimensional simulations were carried out to study the influences of geometrical parameters on the performance of PEMFC under different hydrating conditions. Flow fields, species transport, transport of water in polymer membrane and movement of liquid water in cathode and anode porous layers were determined, in order to accomplish a complete estimation of ohmic and concentration losses of PEMFC power. The geometrical parameters were thickness of the polymer membrane, cathode catalyst layer as well as gas channel to rib width ratio. Every simulation was made under different relative humidities of inlet flows (50 and 100%) for every change of characteristic length. Results show that the influence of the geometrical parameters on ohmic and concentration losses is of considerable importance. The performance of PEMFC is seriously affected under dehydrating conditions. However, such performance may be considerably improved by using suitable geometrical parameters. Cathode and anode liquid saturation may not only affect the transport of species, but also the polymer electrolyte water content. These results show the importance of simultaneously calculating both the water absorption and desorption through the polymer electrolyte and the liquid saturation in the cathode and anode porous mediums to obtain an actual view of ohmic and concentration losses of the PEMFC performance.     

Effects of the humidity and the land ratio of channel and rib in the serpentine three‐dimensional PEMFC model

The construction of a reliable numerical model and the clarification of its operational conditions are necessary for maximizing fuel cell operation. Numerous operating factors, such as mole fractions of species, pressure distribution, overpotential, and inlet relative humidity, affect the performance of proton exchange membrane fuel cells (PEMFCs). Among these operational parameters, geometrical shape and relative humidity are investigated in this paper. Specifically, the land ratio of the gas channel and rib is an important parameter affecting PEMFC performance because current density distribution is influenced by this geometrical characteristic. Three main variables determine the current density distribution, namely, species concentration, pressure, and overpotential distributions. These distributions are considered simultaneously in assessing fuel cell performance with a given PEMFC cell‐operating voltage. In this paper, three different land ratio models are considered to obtain better PEMFC performance. Similarly, three different inlet relative humidity variations are studied to achieve an enhanced operating condition. A three‐dimensional numerical PEMFC model is developed to illustrate the current density distribution as the determining factor for PEMFC performance. Copyright © 2012 John Wiley & Sons, Ltd.     

Experimental analysis of cathode flow stoichiometry on the electrical performance of a PEMFC stack

The paper describes an experimental analysis on the effect of cathode flow stoichiometry on the electrical performance of a PEMFC stack. The electrical power output of a PEMFC stack is influenced by several independent variables (factors). In order to analyse their reciprocal influence, an experimental design methodology was adopted in a previous experimental session, to determine which factors deserve particular attention. In this work, a further experimental analysis has been carried out on a very significant factor: cathode stoichiometry. Its effects on the electrical power of the PEMFC stack have been investigated. The tests were performed on a 3.5 kW_el ZSW stack using the GreenLight GEN VI FC Test Station. The stack characteristics have been obtained running a predefined loading pattern. Some parameters were kept constant during the tests: anode and cathode inlet temperature, anode and cathode inlet relative humidity, anode stoichiometry and inlet temperature of the cooling water. The experimental analysis has shown that an increase in air stoichiometry causes a significant positive effect (increment) on electric power, especially at high-current density, and up to the value of 2 stoichs. These results have been connected to the cathode water flooding, and a discussion was performed concerning the influence of air stoichiometry on electrode flooding at different levels of current density operation.     

Experimental study on water transport coefficient in Proton Exchange Membrane Fuel Cell

Water transport within Proton Exchange Membrane Fuel Cell (PEMFC) is investigated by systematic measurements of the water transport coefficient, defined as the net water flux across the membrane divided by the water production. It is recorded for various operating conditions (current density, gas stoichiometry, air inlet relative humidity, temperature, pressure) in a fuel cell stack fed by dry hydrogen. The measurement of the water transport coefficient shows that a significant fraction of water is collected at the anode while water is produced or injected at the cathode. Moreover, in usual operating conditions, liquid water is present at the cell outlet not only in the cathode but also in the anode. Contrary to the electrical performances, ageing has no influence on the water transport coefficient, which allows the comparison between data collected at different periods of the fuel cell lifetime. From this comparison, it was found that the hydrogen flow rate, the amount of vapor injected at cathode inlet, and the temperature are the main parameters influencing the water transport coefficient. It is shown that air and hydrogen stoichiometry present significant effects on water transport but only through these parameters.     

Phase change in the cathode side of a proton exchange membrane fuel cell

A three-dimensional steady state two-phase non-isothermal model which highly couples the water and thermal management has been developed to numerically investigate the spatial distribution of the interfacial mass transfer phase-change rate in the cathode side of a proton exchange membrane fuel cell (PEMFC). A non-equilibrium evaporation-condensation phase change rate was incorporated in the model which allowed supersaturation and undersaturation take place. The most significant effects of phase-change rate on liquid saturation and temperature distributions are highlighted. A parametric study was also carried out to investigate the effects of operating conditions; namely as the channel inlet humidity, cell operating temperature, and inlet mass flow rate on the phase-change rate. It was also found that liquid phase assumption for produced water in the cathode catalyst layer (CL) changed the local distribution of phase-change rate. The maximum evaporation rate zone (above the channel near the CL) coincided with the maximum temperature zone and resulted in lowering the liquid saturation level. Furthermore, reduction of the channel inlet humidity and an increase of the operation temperature and inlet mass flow rate increased the evaporation rate and allowed for dehydration process of the gas diffusion layer (GDL) to take place faster.     

Effect of anisotropic thermal conductivity of the GDL and current collector rib width on two-phase transport in a PEM fuel cell

A two-dimensional two-phase model based on the classical two-fluid model is used to analyze electrochemical and thermal transport in a PEMFC. The model is extended to account for the dependence of interfacial area density on liquid volume fraction. At a given fixed voltage, the fuel cell generates maximum current density for low through-plane and high in-plane thermal conductivities at high humidity operating conditions. It is also predicted that for low humidity operating conditions, the fuel cell generates maximum current density if the GDL is tailored to have high through-plane thermal conductivity near the inlet and progressively decreasing through-plane thermal conductivity at distances away from the inlet. At fully humidified cathode inlet conditions, narrower current collector ribs generate higher current densities at all voltages by reducing the resistance to diffusion of reactants and products through the GDL. In order to maximize the current density at low humidities, ribs must be wider near the inlet and narrower away from the inlet. The proposed methodology for tailoring GDL through-plane thermal conductivities and rib widths reduces the risk of membrane dehydration near inlet and also reduces the possibility of excessive liquid accumulation in the region away form the inlet.     

Detailed analysis of polymer electrolyte membrane fuel cell with enhanced cross‐flow split serpentine flow field design

Most generally used flow channel designs in polymer electrolyte membrane fuel cells (PEMFCs) are serpentine flow designs as single channels or as multiple channels due to their advantages over parallel flow field designs. But these flow fields have inherent problems of high pressure drop, improper reactant distribution, and poor water management, especially near the U‐bends. The problem of inadequate water evacuation and improper reactant distribution become more severe and these designs become worse at higher current loads (low voltages). In the current work, a detailed performance study of enhanced cross‐flow split serpentine flow field (ECSSFF) design for PEMFC has been conducted using a three‐dimensional (3‐D) multiphase computational fluid dynamic (CFD) model. ECSSFF design is used for cathode part of the cell and parallel flow field on anode part of the cell. The performance of PEMFC with ECSSFF has been compared with the performance of triple serpentine flow design on cathode side by keeping all other parameters and anode side flow field design similar. The performance is evaluated in terms of their polarization curves. A parametric study is carried out by varying operating conditions, viz, cell temperature and inlet humidity on air and fuel side. The ECSSFF has shown superior performance over the triple serpentine design under all these conditions.     

Performance enhancement in a H2/O2 PEMFC with dual-ejector recirculation

Water management in various components of the proton exchange membrane fuel cell (PEMFC) is a significant and challenging issue affecting output performance. PEMFC utilizing dual ejector-based recirculation has been developed to evaluate and improve the performance and water transport properties. A detailed investigation into the effects of ejector operating conditions, such as primary flow pressure and secondary flow relative humidity, on the performance of PEMFC is conducted. The results show that significant performance improvement of PEMFC can be achieved by increasing the operating pressure. The power density can be increased by 37.8% and 86.5% with ejector primary flow pressures of 300 and 400 kPa, respectively. Furthermore, an optimization strategy integrating PEMFC operating condition is proposed to ensure the stability and lifespan of performance. The water management and integration optimization strategy obtained in this paper can provide valuable insight into options for improving the performance of PEMFC with dead-ended anode and cathode.     

Numerical study for in-plane gradient effects of cathode gas diffusion layer on PEMFC under low humidity condition

A numerical study about in-plane porosity and contact angle gradient effects of cathode gas diffusion layer (GDL) on polymer electrolyte membrane fuel cell (PEMFC) under low humidity condition below 50% relative humidity is performed in this work. Firstly, a numerical model for a fuel cell is developed, which considers mass transfer, electrochemical reaction, and water saturation in cathode GDL. For water saturation in cathode GDL, porosity and contact angle of GDL are also considered in developing the model. Secondly, current density distribution in PEMFC with uniform cathode GDL is scrutinized to design the gradient cathode GDL. Finally, current density distributions in PEMFC with gradient cathode GDL and uniform cathode GDL are compared. At the gas inlet side, the current density is higher in GDL with a gradient than GDL with high porosity and large contact angle. At the outlet side, the current density is higher in GDL with a gradient than GDL with low porosity and small contact angle. As a result, gradient cathode GDL increases the maximum power by 9% than GDL with low porosity and small contact angle. Moreover, gradient cathode GDL uniformizes the current density distribution by 4% than GDL with high porosity and large contact angle.     

Water management in a novel proton exchange membrane fuel cell stack with moisture coil cooling

Water flooding causes severe degradation of the performance and lifetime of proton exchange membrane fuel cell (PEMFC). In this study, a novel PEMFC stack with in-built moisture coil cooling was designed and the effects of moisture coil cooling on water management in the new PEMFC stack under various operating conditions were investigated. The result showed that the performance of the PEMFC stack was significantly improved due to the moisture condensation under high current density, high operating temperature, high relative humidity and high operating pressure. The output power was increases by 21.62% (525.71 W) at 1600·mA cm⁻² while the increased parasitic power was no more than 35W. Moreover, degradation of the cathode catalyst layer after 100 h operation was also reduced by using moisture coil cooling. Compared with the situation without moisture condensation, the maximum decay rate of the cathode catalyst layer thickness after 100 h operation was reduced by 13.01%. Accordingly, the novel design is valuable and can be widely used in the future design of PEMFC.     

A study of water transport as a function of the micro-porous layer arrangement in PEMFCs

Electrochemical losses as a function of the micro-porous layer (MPL) arrangement in Proton Exchange Membrane Fuel Cells (PEMFCs) are investigated by electrochemical impedance spectroscopy (EIS). Net water flux across the polymer membrane in PEMFCs is investigated for various arrangements of the MPL, namely with MPL on the cathode side alone, with MPL on both the cathode and the anode sides and without MPL. EIS and water transport are recorded for various operating conditions, such as the relative humidity of the hydrogen inlet and current density, in a PEMFC fed by fully-saturated air. The cell with an MPL on the cathode side alone has better performance than two other types of cells. Furthermore, the cell with an MPL on only the cathode increases the water flux from cathode to anode as compared to the cells with MPLs on both electrodes and cells without MPL. Oxygen-mass-transport resistances of cells in the presence of an MPL on the cathode are lower than the values for the other two cells, which indicates that the molar concentration of oxygen at the reaction surface of the catalyst layer is higher. This suggests that the MPL forces the liquid water from the cathode side to the anode side and decreases the liquid saturation in GDL at high current densities. Consequently, the MPL helps in maintaining the water content in the polymer membrane and decreases the cathode charge transfer and oxygen-mass transport resistances in PEMFCs, even when the hydrogen inlet has a low relative humidity.     

Novel in situ measurements of relative humidity in a polymer electrolyte membrane fuel cell

Miniature temperature/humidity sensors are incorporated into the graphite flowplates of a single cell polymer electrolyte membrane fuel cell (PEMFC) in order to measure the humidity profile along the serpentine channels of both anode and cathode in real time. The sensors show robust performance and importantly are able to recover after saturation. The key observation is a significant increase in relative humidity along the anode gas channel due to back diffusion of water from cathode to anode. Such measurements may be used to determine the water balance in the cell under a range of operating conditions to facilitate model validation and system optimisation.     

A theoretical study of inlet relative humidity control in PEM fuel cell

In this paper, the individual roles of inlet anode and cathode humidification, and their influences on PEM fuel cell’s electrical performance are discussed systematically by using a pseudo two-dimensional, two-phase PEM fuel cell model. It follows that the maximum power density point of a PEM fuel cell is strongly dependent on the combination of the inlet anode and cathode humidification conditions. Their influences, however, are predicted to be highly asymmetrical, with the anode and cathode humidification mainly affecting ohmic and concentration overpotential, respectively. The physical explanation to this asymmetry is given with the aid of a detailed set of simulation results. Finally, the developed understanding of their influences are employed to formulate two examples on the use of inlet relative humidity control as a simple and effective method for maximizing the volumetric power density and operating range of PEM fuel cell, respectively.     

Simultaneous direct visualisation of liquid water in the cathode and anode serpentine flow channels of proton exchange membrane (PEM) fuel cells

Water flooding is detrimental to the performance of the proton exchange membrane fuel cell (PEMFC) and therefore it has to be addressed. To better understand how liquid water affects the fuel cell performance, direct visualisation of liquid water in the flow channels of a transparent PEMFC is performed under different operating conditions. Two high-resolution digital cameras were simultaneously used for recording and capturing the images at the anode and cathode flow channels. A new parameter extracted from the captured images, namely the wetted bend ratio, has been introduced as an indicator of the amount of liquid water present at the flow channel. This parameter, along with another previously used parameter (wetted area ratio), has been used to explain the variation in the fuel cell performance as the operating conditions of flow rates, operating pressure and relative humidity change. The results have shown that, except for hydrogen flow rate, the wetted bend ratio strongly linked to the operating condition of the fuel cell; namely: the wetted bend ratio was found to increase with decreasing air flow rate, increasing operating pressure and increasing relative humidity. Also, the status of liquid water at the anode was found to be similar to that at the cathode for most of the cases and therefore the water dynamics at the anode side can also be used to explain the relationships between the fuel cell performance and the investigated operating conditions.     

Computational study of water transport in proton exchange membrane fuel cells

A computational fuel cell dynamics framework is used to develop a unified water transport equation for a proton exchange membrane fuel cell (PEMFC). Various modes of water transport, i.e., diffusion, convection and electro-osmotic drag, are incorporated in the unified water transport equation. The water transport model is then applied to elucidate water management in three-dimensional fuel cells with dry-to-low humidified inlet gases after its validation against available experimental data for dry oxidant and fuel streams. An internal circulation of water with the aid of counter-flow design is found to be of vital importance for low-humidity operation, for example, in the portable application of a PEMFC without an external humidifier. The general features of water transport in PEMFCs are discussed to show various water transport regimes of practical interest, such as anode water loss, cathode flooding, and the equilibrium condition of water at the channel outlets, particularly for limiting situations where anode and cathode water profiles acquire an equilibrium state. From the practical point of view, the effects of the flow arrangement, membrane thickness, and inlet gas humidity as important determinants of fuel cell performance are also analyzed to elucidate fuel cell water transport characteristics.     

Numerical investigation of liquid water distribution in the cathode side of proton exchange membrane fuel cell and its effects on cell performance

A three-dimensional unsteady two-phase model for the cathode side of proton exchange membrane fuel cell (PEMFC) consisting of gas diffusion layer (GDL) with hybrid structural model is developed to investigate liquid water behaviors under different operating and geometrical conditions and to quantitatively evaluate effects of liquid water distribution on reactant transport and current density distribution. Simulation results reveal that liquid water transport processes and distributions are significantly affected by inlet air velocity, wall wettability and water inlet position, which in turn play a prominent role on local reactant transport and cause considerable disturbances of the current density. Liquid water film spreading on the gas channel (GC) top wall is identified as the most desirable flow pattern in the GC based on overall evaluations of current density magnitude, uniformity of current density distribution and pressure drop in the GC. Modification to GDL structure is proposed to promote the formation of the desirable flow pattern.     

Effects of chlorides on the performance of proton exchange membrane fuel cells

This paper investigates the effects of cathode gases containing chloride ions on the proton exchange membrane fuel cell (PEMFC) performance. Chloride solutions are vaporized using an ultrasonic oscillator and mixed with oxygen/air. The salt concentration of the mixed gas in the cathode is set by varying the concentration of the chloride solution. Five-hour tests show that an increase in the concentration of sodium chloride did not significantly affect the cell performance of the PEMFC. It is found that variations in the concentration of chloride do not show significant influence on the cell performance at low current density operating condition. However, for high current density operating conditions and high calcium chloride concentrations, the chloride ion appears to have a considerable effect on cell performance. Experimental results of 108-h tests indicate that the fuel cell operating with air containing calcium chloride has a performance decay rate of 3.446 mV h⁻¹ under the operating condition of current density at 1 A/cm². From the measurements of the I-V polarization curves, it appears that the presence of calcium chloride in the cathode fuel gas affects the cell performance more than sodium chloride does.