The experimental results and simulation of temperature dependence of brittle‐ductile transition in PVC/CPE blends and PVC/CPE/nano‐CaCO3 composites

The effect of chlorinated polyethylene (CPE) content and test temperature on the notched Izod impact strength and brittle‐ductile transition behaviors for polyvinylchloride (PVC)/CPE blends and PVC/CPE/nano‐CaCO₃ ternary composites is studied. The CPE content and the test temperature regions are from 0–50 phr and 243–363 K, respectively. It is found that the optimum nano‐CaCO₃ content is 15 phr for PVC/CPE/nano‐CaCO₃ ternary composites. For both PVC/CPE blends and PVC/CPE/nano‐CaCO₃ ternary composites, the impact strength is improved remarkably when the CPE content or test temperature is higher than the critical value, that is, brittle‐ductile transition content (C_BD) or brittle‐ductile transition temperature (T_BD). The T_BD is closely related to the CPE content, the higher the CPE content, the lower the T_BD. The temperature dependence of impact strength for PVC/CPE blends and PVC/CPE/nano‐CaCO₃ ternary composites can be well simulated with a logistic fitting model, and the simulation results can be illustrated with the percolation model proposed by Wu and Jiang. DMA results reveal that both PVC and CPE can affect the T_BD of PVC/CPE blends and PVC/CPE/nano‐CaCO₃ composites. When the CPE content is enough (20 phr), the CPE is more important than PVC for determining the T_BD of PVC/CPE blends and PVC/CPE/nano‐CaCO₃ composites. Scanning electron microscopy (SEM) observations reveal that the impact fractured mechanism can change from brittle to ductile with increasing test temperature for these PVC systems. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Preparation and characterization of polyamide 6/liquid natural rubber blends

This study presents a new approach to toughen Polyamide 6 (PA6) by using a low‐molecular weight liquid natural rubber (LNR). The LNR is prepared by mastication of pale latex crepe in the presence of 0.5 phr Peptizol 7. The PA6/LNR blend samples are characterized in terms melt flow index, hardness, abrasion resistance, impact strength, flexural strength, tensile strength, and thermal properties. The impact strength of PA6 increases by about 67% upon addition of 10% LNR. The percolation model is applied to study of brittle to ductile transition. The percolation threshold for the brittle to ductile transition of the blend was found to be 14.5 wt % LNR, corresponding to the critical volume fraction of the stress volume, V_sc = 0.58, which is consistent with the calculated value of ≈ π/6. The PA6/LNR blends exhibit cavitation and matrix shear yielding, which would be the main contribution to the increases impact strength. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 39750.     

Compatibilization of polypropylene/Poly(acrylonitrile‐butadiene‐styrene) blends by polypropylene‐graft‐cardanol

The polypropylene‐graft‐cardanol (PP‐g‐cardanol) was prepared by reactive extrusion with polypropylene (PP) and natural renewable cardanol which could increase the interfacial energy of PP and inhibit the degradation of PP during the process of reactive extrusion and usage. In this article, PP‐g‐cardanol and polypropylene‐graft‐maleic anhydride (PP‐g‐MAH) were used as compatibilizers of the polypropylene (PP)/poly(acrylonitrile‐butadiene‐styrene) (ABS) blends. PP/ABS (70/30, wt %) blends with PP‐g‐cardanol and PP‐g‐MAH were prepared by a corotating twin‐screw extruder. From the results of morphological studies, the droplet size of ABS was minimized to 1.93 and 2.01 μm when the content of PP‐g‐cardanol and PP‐g‐MAH up to 5 and 7 phr, respectively. The results of mechanical testing showed that the tensile strength, impact strength and flexural strength of PP/ABS (70/30) blends increase with the increasing of PP‐g‐cardanol content up to 5 phr. The complex viscosity of PP/ABS (70/30) blends with 5 phr PP‐g‐cardanol showed the highest value. Moreover, the change of impact strength and tensile strength of PP/ABS (70/30) blends were investigated by accelerated degradation testing. After 4 accelerated degradation cycles, the impact strength of the PP/ABS (70/30) blends with 5 phr PP‐g‐cardanol decrease less than 6%, but PP/ABS (70/30) blends with 5 phr PP‐g‐MAH and without compatibilizer decrease as much as 12% and 32%, respectively. The tensile strength of PP/ABS (70/30) blends has a similar tendency to that of impact strength. The above results indicated that PP‐g‐cardanol could be used as an impact modifier and a good compatibilizer, which also exhibited better stability performance during accelerated degradation testing. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41315.     

Super‐toughed polymer blends derived from polypropylene random copolymer and ethylene/styrene interpolymer

In this article, blends of polypropylene random copolymer (PP‐R) with a novel impact modifier, namely ethylene/styrene interpolymer (ESI), were prepared to evaluate the effectiveness of ESI in toughening PP‐R and the influence of ESI content on the mechanical, thermal, and rheological properties of polymer blends. Results showed that super‐toughened PP‐R/ESI blends (ca. Izod impact strength ≥ 500 J/m) were readily achieved with only 5 wt % ESI. The blends exhibited significant improvement in both impact strength and elongation, while small loss in tensile strength and elastic modulus when increasing ESI content. ESI had a nucleating effect that caused PP matrix to crystallize at higher temperatures, whereas PP‐R/ESI blends presented lower melting temperatures (T_m) than PP‐R matrix and T_m decreased with the increment of ESI content. Rheology study indicated that both PP‐R matrix and PP‐R/ESI blends presented shear thinning behaviors during melt processing. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Low density polyethylene-polypropylene blends: Part 1 - Ductility and tensile properties

Abstract

The composition-property relationships of LDPE-PP binary blends have been investigated. Young's modulus, yield strength and flexural strength of the blends varied monotonically with composition, whereas the elongation at failure and the true ultimate tensile strength for the blends with 30-50 wt-% PP exhibited synergetic effects. These blends showed strong cold draw hardening, and their elongations at failure and the true ultimate tensile strengths were much higher than those of the neat components. Meanwhile, impact strength showed an abrupt reduction with increasing PP content and the failure mode changed from ductile to brittle in the composition range of 30-50 wt-% PP. Failure mechanisms are discussed, addressing interfacial adhesion between LDPE and PP and the non-uniform shrinkage of the component domains upon cooling.     

PP/LLDPE交联共混物的力学性能研究

采用两步交联加工法制备出具有优良力学性能的PP／LLDPE共混物。实验表明：当m(PP)／m(LLDPE)／m(SBS)／m(交联剂)为80／20／10／3时，交联共混物的冲击强度、拉伸强度和断裂伸长率分别达到466．3J／m、27．1MPa和715．1％，比未交联的共混物分别提高262％、8．28％和115％；交联作用的存在使共混物的脆韧转变点明显提前；随交联剂用量的增加，共混物的力学性能不断提高，但增大趋势逐渐变小。     

Poly(butylene terephthalate)/poly(ethylene glycol) blends with compatibilizers

Polymer blend systems offer a versatile approach for tailoring the properties of polymer materials for specific applications. In this study, we investigated the compatibility of polybutylene terephthalate (PBT) and poly(ethylene glycol) (PEG) blends processed using a twin-screw extruder, with the aim of enhancing their compatibility. Phthalic anhydride (PAn) and phthalic acid (PAc) were used as potential compatibilizers at different concentrations to improve interfacial interactions between PBT and PEG. Blend morphologies were characterized using scanning electron microscopy, which revealed improved interfacial compatibility and reduced phase separation with the incorporation of small amounts of PAn and PAc. Differential scanning calorimetry analysis indicated changes in the melting temperature (T_m) and glass transition temperature (T_g) of the blends owing to the compatibilizing effects of PAn and PAc. Dynamic mechanical analysis further corroborated the influence of the compatibilizers on the T_g and viscoelastic behavior. Thermogravimetric analysis demonstrated enhanced thermal stability with the addition of either PAn or PAc. Rheological measurements indicated an increase in complex viscosity with increasing compatibilizer content, indicating improved compatibility. The degradation point (T_d) of PBT/PEG blend increased from 158 to 200 and 319°C with the incorporation of 5 phr PAn and 2 phr PAc, respectively. Mechanical properties, including tensile strength, Young's modulus, and Izod impact strength, were evaluated. For instance, the tensile strength of PBT/PEG blend was enhanced from 43.5 to 48.7 and 49.7 MPa by incorporating 5 phr PAn and 2 phr PAc, respectively. However, the impact strength of PBT/PEG blend increased from 3.0 to 4.3 and 4.2 kJ/m² with the addition of 1 phr PAn and 1 phr PAc, respectively. The findings demonstrated that adding 5 phr PAn or 2 phr PAc to the PBT/PEG blends was advantageous, achieving a harmony of performance benefits and compromises. Rheological observations contributed significantly to the mechanical and thermal properties. Overall, the study highlights the significance of utilizing PAn and PAc as effective compatibilizers for enhancing the properties of PBT/PEG blends, making them potential candidates for various applications.     

Mechanical and Morphological Properties of PP/LLPDE/NR Blends—Effects of Polyoctenamer

In this study, impact-modified polypropylene (PP) ternary blends based on PP/natural rubber (NR)/linear low-density polyethylene (LLDPE) with ratios of 72/10/18 and 64/20/16 were produced by a twin-screw extruder with polyoctenamer (TOR) as the compatibilizer. The mechanical properties of the blends were determined on injection-molded specimens in tensile, flexural, and impact testing. The impact strength and elongation at break of the blend increased significantly while the flexural modulus and tensile strength decreased slightly with increasing TOR content. The impact strength improved with the increasing TOR due the increase of interfacial adhesion resulting in finer dispersion of the rubbery minor phase in the PP matrix. The improvement in compatibility with the addition of TOR into PP/NR/LLDPE blends is being supported by both scanning electron microscopy (SEM) and dynamic mechanical analysis (DMA).     

Fabrication of polypropylene blends with excellent low‐temperature toughness and balanced toughness‐rigidity by a combination of EPR and SEEPS

To overcome serious rigidity depression of rubber‐toughened plastics and fabricate a rigidity‐toughness balanced thermoplastic, a combination of styrene‐[ethylene‐(ethylene‐propylene)]‐styrene block copolymer (SEEPS) and ethylene‐propylene rubber (EPR) was used to toughen polypropylene. The dynamic mechanical properties, crystallization and melting behavior, and mechanical properties of polypropylene (PP)/EPR/SEEPS blends were studied in detail. The results show that the combination of SEEPS and EPR can achieve the tremendous improvement of low‐temperature toughness without significant strength and rigidity loss. Dynamic mechanical properties and phase morphology results demonstrate that there is a good interfacial strength and increased loss of compound rubber phase comprised of EPR component and EP domain of SEEPS. Compared with PP/EPR binary blends, although neither glass transition temperature (T_g) of the rubber phase nor T_g of PP matrix in PP/EPR/SEEPS blends decreases, the brittle‐tough transition temperature (T_bd) of PP/EPR/SEEPS blends decreases, indicating that the increased interfacial interaction between PP matrix and compound rubber phase is also an effective approach to decrease T_bd of the blends so as to improve low‐temperature toughness. The balance between rigidity and toughness of PP/EPR/SEEPS blends is ascribed to the synergistic effect of EPR and SEEPS on toughening PP. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 45714.     

Dynamically cured polypropylene/Novolac blends compatibilized with maleic anhydride‐g‐polypropylene

In this article, the dynamic vulcanization process was applied to polypropylene (PP)/Novolac blends compatibilized with maleic anhydride‐grafted PP (MAH‐g‐PP). The influences of dynamic cure, content of MAH‐g‐PP, Novolac, and curing agent on mechanical properties of the PP/Novolac blends were investigated. The results showed that the dynamically cured PP/MAH‐g‐PP/Novolac blend had the best mechanical properties among all PP/Novolac blends. The dynamic cure of Novolac improved the modulus and stiffness of the PP/Novolac blends. The addition of MAH‐g‐PP into dynamically cured PP/Novolac blend further enhanced the mechanical properties. With increasing Novolac content, tensile strength, flexural modulus, and flexural strength increased significantly, while the elongation at break dramatically deceased. Those blends with hexamethylenetetramine (HMTA) as a curing agent had good mechanical properties at HMTA content of 10 wt %. Scanning electron microscopy (SEM) analysis showed that dynamically cured PP/MAH‐g‐PP/Novolac blends had finer domains than the PP/MAH‐g‐PP/Novolac blends. Thermogravimetric analysis (TGA) results indicated that the incorporation of Novolac into PP could improve the thermal stability of PP. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2007     

Mechanical and thermal properties of SEBS‐g‐MA compatibilized halloysite nanotubes reinforced polyethylene terephthalate/polycarbonate/nanocomposites

In this study, the effect of maleic anhydride grafted styrene‐ethylene‐butylene‐styrene (SEBS‐g‐MA) content on mechanical, thermal, and morphological properties of polyethylene terephthalate/polycarbonate/halloysite nanotubes (PET/PC/HNTs) nanocomposites has been investigated. Nanocomposites of PET/PC (70 : 30) with 2 phr of HNTs were compounded using the counter rotating twin screw extruder. A series of formulations were prepared by adding 5–20 phr SEBS‐g‐MA to the composites. Incorporation of 5 phr SEBS‐g‐MA into the nanocomposites resulted in the highest tensile and flexural strength. Maximum improvement in the impact strength which is 245% was achieved at 10 phr SEBS‐g‐MA content. The elongation at break increased proportionately with the SEBS‐g‐MA content. However, the tensile and flexural moduli decreased with increasing SEBS‐g‐MA content. Scanning electron microscopy revealed a transition from a brittle fracture to ductile fracture morphology with increasing amount of SEBS‐g‐MA. Transmission electron microscopy showed that the addition of SEBS‐g‐MA into the nanocomposites promoted a better dispersion of HNTs in the matrix. A single glass transition temperature was observed from the differential scanning calorimetry test for compatibilized nanocomposites. Thermogravimetric analysis of PET/PC/HNTs nanocomposites showed high thermal stability at 15 phr SEBS‐g‐MA content. However, on further addition of SEBS‐g‐MA up to 20 phr, thermal stability of the nanocomposites decreased due to the excess amount of SEBS‐g‐MA. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42608.     

Boiling water aging of polycarbonate and polycarbonate/acrylonitrile–butadiene–styrene resin and polycarbonate/low‐density polyester blends

The effects of boiling water on the mechanical and thermal properties and morphologies of polycarbonate (PC), PC/acrylonitrile–butadiene–styrene resin (PC/ABS), and PC/low‐density polyester (PC/LDPE) blends (compositions of PC/ABS and PC/LDPE blends were 80/20) were studied. PC and the PC/ABS blend had a transition from ductile to brittle materials after boiling water aging. The PC/LDPE blend was more resistant to boiling water aging than PC and the PC/ABS blend. The thermal properties of glass‐transition temperature (T_g) and melting temperature (T_m) in PC and the blends were measured by DSC. The T_g of PC and PC in the PC/ABS and PC/LDPE blends decreased after aging. The T_g of the ABS component in the PC/ABS blend did not change after aging. The supersaturated water in PC clustered around impurities or air bubbles leading to the formation of microcracks, which was the primary reason for the ductile–brittle transition in PC, and the microcracks could not recover after PC was treated at 160°C for 6 h. The PC/ABS blend showed slightly higher resistance to boiling water than did PC. The highest resistance to boiling water of the PC/LDPE blend may be attributed to its special structural morphology. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 89: 589–595, 2003     

The effect of poly(ethylene glycol) as plasticizer in blends of poly(lactic acid) and poly(butylene succinate)

The effect of polyethylene glycol (PEG) on the mechanical and thermal properties of poly(lactic acid) (PLA)/poly(butylene succinate) (PBS) blends was examined. Overall, it was found that PEG acted as an effective plasticizer for the PLA phase in these microphase‐separated blends, increasing the elongation at break in all blends and decreasing the T_g of the PLA phase. Significant effects on other properties were also observed. The tensile strength and Young's modulus both decreased with increasing PEG content in the blends. In contrast, the elongation at break increased with the addition of PEG, suggesting that PEG acted as a plasticizer in the polymer blends. Scanning electron microscope images showed that the fracture mode of PLA changed from brittle to ductile with the addition of PEG in the polymer blends. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43044.     

Fracture and impact properties of polycarbonates and MBS elastomer-modified polycarbonates

Mechanical properties of polycarbonates (PCs) and elastomer-modified polycarbonates with various molecular weights (MW) are investigated. Higher MW PCs show slightly lower density, yield stress, and modulus. The ductile–brittle transition temperature (DBTT) of the notched impact strength decreases with the increase of PC MW and with the increase of elastomer content. The elastomer-modified PC has higher impact strength than does the unmodified counterpart if the failure is in the brittle mode, but has lower impact strength if the failure is in the ductile mode. The critical strain energy release rate (G_c) measured at ?30°C decreases with the decrease of PC MW. The extrapolated zero fracture energy was found at M_n = 6800 or MFR = 135. The G_c of the elastomer-modified PC (MFR = 15, 5% elastomer) is about twice that of thee unmodified one. The presence of elastomer in the PC matrix promotes the plane–strain localized shear yielding to greater extents and thus increases the impact strength and G_c in a typically brittle fracture. Two separate modes, localized and mass shear yielding, work simultaneously in the elastomer-toughening mechanism. The plane–strain localized shear yielding dominates the toughening mechanism at lower temperatures and brittle failure, while the plane–stress mass shear yielding dominates at higher temperatures and ductile failure. For the elastomer-modified PC (10% elastomer), the estimated extension ratio of the yielding zone of the fractured surface is 2 for the ductile failure and 5 for the brittle crack. A criterion for shifting from brittle to ductile failure based on precrack critical plastic-zone volume is proposed.     

Probing toughness of polycarbonate (PC: ductile and brittle)/polypropylene (PP) blends and talc-triggered PC/PP brittle composites with diverse impact fracture parameters

Polycarbonates (PCs) are commonly used as a blend and a composite to achieve pecuniary advantages and dimensional stability. While the toughness of a homogeneous PC matrix has been extensively investigated, examination for the toughness of heterogeneous blend systems such as PC/polypropylene (PP) blends has been limited. Furthermore, recent interest in highly flowable PCs (low-molecular-weight PCs with low ductility) has surfaced due to the large and geometrically complex plastic parts. Herein, the toughness for PC/PP blends and PC/PP/talc composites in a ductile and a brittle PC matrix was explored by using various toughness measurements such as notched Izod impact strength, falling dart impact, boss quasi-static energy/impact energy, and tensile toughness tests. In a ductile PC matrix [melt flow index (MFI) = 8], the incorporation of PP gradually reduced the toughness. On the other hand, the toughness was improved by 450% at 2 wt % PP in a brittle PC matrix (MFI = 19). Similarly, in the talc-induced brittle PC matrix, the toughness was enhanced at the PP loading from 2 to 10 wt %. The density of PC/PP blends was gradually reduced from 1.19 to 1.10 g cm⁻³ with increasing PP concentration from 0 to 20 wt %. Degradation, density, thermal behaviors, and morphology were also investigated. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2019 , 136, 47110.     

Development of nanofibrous morphology in LDPE/LLDPE/PP blends and its effect on mechanical properties of blend films

Nanofibrous morphology has been observed in ternary blends of low density polyethylene (LDPE), linear low density polyethylene (LLDPE), and isotactic polypropylene (PP) when these were melt‐extruded via slit die followed by hot stretching. The morphology was dependent on the concentration of the component polymers in ternary blend LDPE/LLDPE/PP. The films were characterized by wide angle X‐ray diffraction (XRD), scanning electron microscopy (SEM), and testing of mechanical properties. The XRD patterns reveal that the β phase of PP is obtained in the as‐stretched nanofibrillar composites, whose concentration decreases with the increase of LLDPE concentration. The presence of PP nanofibrils shows significant nucleation ability for crystallization of LDPE/LLDPE blend. The SEM observations of etched samples show an isotropic blend of LDPE and LLDPE reinforced with more or less randomly distributed and well‐defined nanofibrils of PP, which were generated in situ. The tensile modulus and strength of LDPE/LLDPE/PP blends were significantly enhanced in the machine direction than in the transverse direction with increasing LLDPE concentration. The ultimate elongation increased with increasing LLDPE concentration, and there was a critical LLDPE concentration above which it increased considerably. There was a dramatic increase in the falling dart impact strength for films obtained by blow extrusion of these blends. These impressive mechanical properties of extruded samples can be explained on the basis of the formation of PP nanofibrils with high aspect ratio (at least 10), which imparted reinforcement to the LDPE/LLDPE blend. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Polypropylene blends with a phenoxy

Polypropylene (PP) blends with a phenoxy have been prepared in various compositions using a Brabender Plasticorder. Scanning electron microscopy (SEM) micrographs showed a clean two-phase morphology. The domains were larger when PP formed the dispersed phase, probably due to the greater melt viscosity of PP. The melting peak temperature (T_m) of PP decreased marginally, whereas the glass transition temperature (T_g) of phenoxy increased by 5-10°C, in the blends. X-ray diffraction measurements indicated that PP crystallizes in a hexagonal β-form in 50/50 and 30/70 (PP/phenoxy) blends. Mechanical properties of the blends generally showed negative deviation from the additivity rule, perhaps due to the inherently immiscible nature of the blends. © 1996 John Wiley & Sons, Inc.     

Dynamic Mechanical Properties of Poly(propylene) Blends with Poly[ethylene‐co‐(methyl acrylate)]

Summary: Blends of poly(propylene) (PP) were prepared with poly[ethylene‐co‐(methyl acrylate)] (EMA) having 9.0 and 21.5% methyl acrylate comonomer. A similar series of blends were compatibilized by using maleic anhydride grafted PP. The morphology and mechanical properties of the blends were investigated using differential scanning calorimetry (DSC) and dynamic mechanical analysis (DMA) in tensile mode. The DMA method and conditions were optimized for polymer film specimens and are discussed in the experimental section. The DSC results showed separate melting that is indicative of phase‐separated blends, analogous to other PP‐polyethylene blends but with the added polarity of methyl acrylate pendant side groups that may be beneficial for chemical resistance. Heterogeneous nucleation of PP was decreased in the blends because of migration of nuclei into the more polar EMA phase. The crystallinity and peak‐melting temperature did not vary significantly, although the width of the melting endotherm increased in the blends indicating a change had occurred to the crystals. DMA analysis showed the crystal‐crystal slip transition and glass transition (T_g) for PP as well as a T_g of the EMA copolymer occurring chronologically toward lower temperatures. The storage modulus of PP and the blends was generally greater with annealing at 150 °C compared with isothermal crystallization at 130 °C. The storage modulus of the blends for isothermally crystallized PP increased with 5% EMA, then decreased for higher amounts of EMA. Annealing caused a decrease with increasing copolymer content. The extent of the trend was greater for the compatibilized blends. The T_g of the blends varied over a small range, although this change was less for the compatibilized blends.

Storage modulus for PP and EMA9.0 blends annealed at 150 °C.     

Influence of oil contents in dynamically cured natural rubber and polypropylene blends

Mechanical, dynamic, thermal, and morphological properties of dynamically cured 60/40 NR/PP TPVs with various loading levels of paraffinic oil were investigated. It was found that stiffness, hardness, tensile strength, storage shear modulus, complex viscosity, glass transition temperature (T_g) of the vulcanized rubber phase, degree of crystallinity and crystalline melting temperature (T_m) of the polypropylene (PP) phase decreased with increasing loading levels of oil. This is attributed to distribution of oil into the PP and vulcanized rubber domains causing oil‐swollen amorphous phase and vulcanized rubber domains. An increasing trend of elastic response in terms of tension set and damping factor was observed in the TPVs with loading levels of oil in a range of 0–20 phr. It is supposed that a major proportion of oil was first preferably migrated into the PP phase and caused an abrupt decreasing trend of degree of crystallinity and T_m of the PP phase. The dispersed vulcanized rubber domains remained small as particles with a low degree of swelling. Increasing loading levels of oil higher than 20 phr caused a decreasing trend of elongation at break and elastomeric properties. Saturation of oil in the PP phase was expected and the excess oil was transferred to the rubber phase which thereafter caused larger swollen vulcanized rubber domains. The remaining amount of oil was able to separate as submicron pools distributed in the PP matrix. This caused lowering of T_g, T_m, crystallinity of PP phase as well as strength, elastomeric, and dynamic properties of the TPVs. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Studies of poly(2,6-dimethyl-1,4-phenylene oxide) blends: 2. Poly(4-methylstyrene)

Blends of poly(2,6-dimethyl-1,4-phenylene oxide) (PMMPO) and poly(4-methylstyrene) (P4MS) were found to be compatible from a variety of experimental methods including calorimetric, density, and mechanical property measurements. Blend property behavior was similar to that widely reported for PMMPO/polystyrene (PS) blends. For each blend composition studied, a single glass transition temperature (T_g) was detected by differential scanning calorimetry. The compositional dependence of blend T_g was equally well represented by the empirical inverse rule of mixtures or by the Couchman thermodynamic expression. Density measurements of molded films suggested a mild excess volume of mixing that was slightly smaller than that observed for blends of PMMPO and PS. As in the case for PMMPO/PS, densification in the solid state may be associated with the observed mechanical property behavior of the PMMPO/P4MS blends. Initial modulus at each blend composition was larger than would be predicted by a simple weighted average of component polymer values. Tensile deformation changed from a ductile to a brittle mode of failure with increasing P4MS composition. The yield stress for ductile compositions and ultimate stress of brittle samples were both higher than found for the corresponding unblended polymers and higher than would be predicted from a simple additive relationship of weighted component properties. Blend impact strength determined by small strain rate tensile tests rapidly decreased to low levels with increasing P4MS composition. This drop in impact strength became more composition sensitive at higher loading rates during multiaxial deformation in an instrumented dart impact tester.