Effects of the oxidation temperature on the structure and properties of polyacrylonitrile‐based activated carbon hollow fiber

Polyacrylonitrile (PAN) hollow fibers were pretreated with ammonium dibasic phosphate, oxidized in air, carbonized in nitrogen, and activated with carbon dioxide. The effects of the oxidation temperature of the PAN hollow fiber precursor on the microstructure, specific surface, pore size distribution, and adsorption properties of PAN‐based activated carbon hollow fiber (PAN‐ACHF) were studied. When PAN hollow fibers were oxidized at 270°C, because of drastic oxidation, chain scission occurred, and the number of pores within and on the surface of the resultant PAN‐ACHF increased, but the pores were just in the thinner region of the skin of PAN‐ACHF. The surface area of PAN‐ACHF reached a maximum when the oxidation temperature was 270°C. The adsorption ratios to creatinine were all higher than 90% at all oxidation temperatures, and the adsorption ratio to VB₁₂ reached a maximum (97%) at 230°C. The dominant pore sizes of the mesopores in PAN‐ACHF ranged from 2 to 5 nm. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 98: 203–207, 2005     

Effect of hypochlorite concentration on properties of posttreated outer‐skin ultrafiltration membranes spun from cellulose acetate/poly(vinyl pyrrolidone) blends

An outer‐skin hollow‐fiber ultrafiltration (UF) membrane was spun from a new dope solution containing cellulose acetate (CA)/poly(vinyl pyrrolidone) (PVP 360K)/N‐methyl‐2‐pyrrolidone (NMP)/water using a wet‐spinning technique. The as‐spun fibers were posttreated with a hypochlorite solution over a range of concentrations for a fixed period of 24 h. The experimental results showed that the pure water flux of the treated membrane increased with increasing hypochlorite concentration. The treated membrane experienced an increased fouling tendency with increasing hypochlorite concentration because the hydrophilicity of the treated membrane decreased as a result of the removal of PVP contents in the membrane matrix after hypochlorite treatment. SEM images revealed that the membrane had an outer dense skin, a porous inner surface, and a spongelike structure, which confirmed that addition of PVP favored the suppression of macrovoids in the membrane. The membrane pore size could be significantly increased when the hypochlorite concentration reached 200 mg/L. It was concluded that hypochlorite treatment provided an additional option to easily alter the pore size of UF membranes. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 97: 227–231, 2005     

Effect of polyvinylpyrrolidone molecular weights on morphology,oil/water separation,mechanical and thermal properties of polyetherimide/polyvinylpyrrolidone hollow fiber membranes

We prepared polyetherimide (PEI) hollow fiber membranes using polyvinylpyrrolidones (PVP) with different molecular weights (PVP 10,000, PVP 40,000, and PVP 1,300,000) as additives for oil/water separation. Asymmetric hollow fiber membranes were fabricated by wet phase inversion technique from 25 wt % or 30 wt % solids of 20 : 5 : 75 or 20 : 10 : 70 (weight ratio) PEI/PVP/N‐metyl‐2‐pyrrolidone (NMP) solutions and a 95 : 5 NMP/water solution was used as bore fluid to eliminate resistance on the internal surface. Effects of PVP molecular weights on morphology, oil‐surfactant‐water separation characteristics, mechanical, and thermal properties of PEI/PVP hollow fiber membranes were investigated. It was found that an increase in PVP molecular weight and percentage in PEI/PVP dope solution resulted in the membrane morphology change from the finger‐like structure to the spongy structure. Without sodium hypochlorite posttreatment, hollow fiber membranes with higher PVP molecular weights had a higher rejection but with a lower water flux. For oil‐surfactant‐water emulsion systems (1600 ppm surfactant of sodium dodecylbenzenesulfonate and 2500 ppm oil of n‐decane), experimental results illustrated that the rejection rates for surfactant, total organic carbon, and oil were 76.1 ≈ 79.8%, 91.0 ≈ 93.0%, and more than 99%, respectively. Based on the glass transition temperature values, PVP existed in hollow fiber membranes and resulted in the hydrophilicity of membranes. In addition, using NaOCl as a posttreatment agent for membranes showed a significant improvement in membrane permeability for PVP with a molecular weight of 1300 K, whereas the elongation at break of the treated hollow fiber membranes decreased significantly. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 74: 2220–2233, 1999     

Stability of acrylic acid grafted poly(vinylidene fluoride) hollow fiber membrane prepared by high‐energy electron beam

In this article, poly(vinylidene fluoride) (PVDF) hollow fiber membrane and acrylic acid (AA) were co‐irradiated by high‐energy electron beam to introduce hydrophilic carboxylic groups on the membrane surface. Thermal capability, mechanical performance, pore size, and permeation property were investigated to determine the stability of the membrane pore structure before and after irradiation polymerization. The decomposition temperature, melting point, glass transition temperature, and breaking force of the PVDF‐g‐AA membrane increased slightly because of irradiation grafting polymerization. After 15 months of storage, the pore size distribution of the PVDF‐g‐AA membrane became smaller and more dispersive. The pure water flux and the rejection to bovine serum albumin of the PVDF‐g‐AA membrane increased significantly with the increase in hydrophilicity and decrease in pore size. The results indicated that the structure and properties of the PVDF hollow fiber membrane were stable after high‐energy electron beam irradiation grafting polymerization, even after 15 months of storage. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 41165.     

多孔涤纶的制备工艺及性能

为获得具有孔隙结构的涤纶,利用碱处理的方法将具有中空结构的涤纶浸入NaOH溶液中,通过NaOH对涤纶的水解作用在中空涤纶的表面产生刻蚀,从而形成多孔的纤维结构.分别考察了不同质量浓度、温度及浸渍时间条件下,所形成多孔纤维的形貌特征、孔隙率、力学性能及所制备织物的亲水性.结果 表明,采用碱处理法能够有效地制备多孔涤纶,孔...     

Effect of fiber surface morphology on the hydrophilicity modification of cold plasma‐treated polypropylene nonwoven fabrics

Cold oxygen plasma was employed to give hydrophilicity modification to polypropylene (PP) nonwoven fabric (NWF). It was found that, after plasma treatment, PP NWF made from fibers with smooth surfaces can only keep its hydrophilicity for a short time and then shows a quick hydrophobic recovery at room temperature. However, this hydrophilic property can last for a long time in the case of the PP NWF made from fibers with rough surfaces. To prove the contribution of the rough surface to the long‐term hydrophilicity, this PP NWF was treated in an organic solvent to smooth the fiber surface. The hydrophilic feature of this PP NWF no longer lasts for a long time after the same plasma treatment. This observation strongly supports our opinion that the fiber surface morphology of PP NWF is a critical factor for long‐term hydrophilicity improvement after plasma treatment, which gives a positive solution to overcoming the aging effect of hydrophilicity modification often found in this technique. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Effects of oxidation time on the structure and properties of polyacrylonitrile‐based activated carbon hollow fiber

Polyacrylonitrile (PAN) hollow fibers were pretreated with ammonium dibasic phosphate, then further oxidized in air, carbonized in nitrogen, and activated with carbon dioxide. The effects of oxidation time of PAN hollow fiber precursor on the microstructure, specific surface, pore size distribution, and adsorption properties of PAN‐based activated carbon hollow fiber (PAN‐ACHF) were studied in this work. Both of specific surface area and adsorption ratio to VB₁₂ reach maximums when PAN hollow fibers are oxidized for 5 h in air. The adsorption ratios for creatinine are all higher than 90% over all oxidation time. After 5 h of oxidation, the number of pores on the surface obviously increases, and the pore size is uniform. After 7 h of oxidation, the number of macropores in PAN‐ACHF increases. The dominant pore sizes of mesopores in PAN‐ACHF range from 2 to 5 nm. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2007     

Enzyme‐mediated grafting of acrylamide to ultrahigh molecular weight polyethylene fiber: A novel radical initiation system

The enzyme‐mediated grafting of acrylamide (AM) to ultrahigh molecular weight polyethylene (UHMWPE) fibers using horseradish peroxidase (HRP) was demonstrated. To optimize the reaction condition, the concentrations of monomer, H₂O₂, the initiator, and time were varied. The grafting results were discussed and a reaction mechanism was proposed. Function groups and structural change of the graft copolymer were determined by FTIR spectroscopic and scanning electron microscopy micrographs for proof of grafting and the results were discussed. Results show that the surface of treated fiber becomes rougher than the untreated surface. Compared to unmodified fiber, modified fiber surface had significantly increased the interfacial shear strength, and carbonyl‐stretching regions in the IR spectra. The interfacial shear strength of the UHMWPE fiber increased, clearly indicating that enzymatic‐grafted acrylamide could significantly increase the hydrophilicity of the surfaces of UHMWPE fibers. Moreover, the hydrophilicity of treated fiber depends on the monomer concentration, the initiator concentration, and oxidizing agent concentration as well as the time of the reaction. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 96: 1011–1016, 2005     

Poly(vinylidene fluoride‐co‐hexafluoropropylene) (PVDF‐co‐HFP) hollow fiber membranes prepared from PVDF‐co‐HFP/PEG‐600Mw/DMAC solution for membrane distillation

Poly(vinylidene fluoride‐co‐hexafluoropropylene) (PVDF‐co‐HFP) hollow fiber membranes were prepared by using the phase inversion method. The effect of polyethylene glycol (PEG‐600Mw) with different concentrations (i.e., 0, 5, 7, 10, 12, 15, 18, and 20 wt %) as a pore former on the preparation and characterization of PVDF‐co‐HFP hollow fibers was investigated. The hollow fiber membranes were characterized using scanning electron microscopy, atomic force microscopy, and porosity measurement. It was found that there is no significant effect of the PEG concentration on the dimensions of the hollow fibers, whereas the porosity of the hollow fibers increases with increase of PEG concentration. The cross‐sectional structure changed from a sponge‐like structure of the hollow fiber prepared from pure PVDF‐co‐HFP to a finger‐like structure with small sponge‐like layer in the middle of the cross section with increase of PEG concentration. A remarkable undescribed shape of the nodules with different sizes in the outer surfaces, which are denoted as “twisted rope nodules,” was observed. The mean surface roughness of the hollow fiber membranes decreased with an increase of PEG concentration in the polymer solution. The mean pore size of the hollow fibers gradually increased from 99.12 to 368.91 nm with increase of PEG concentration in polymer solution. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Investigation on the effect of spinning conditions on the properties of hollow fiber membrane for hemodialysis application

Polyethersulfone (PES) hollow fiber membranes were fabricated via the dry‐wet phase inversion spinning technique, aiming to produce an asymmetric, micro porous ultrafiltration hollow‐fiber specifically for hemodialysis membrane. The objective of this study is to investigate the effect of spinning conditions on the morphological and permeation properties of the fabricated membrane. Among the parameters that were studied in this work are air gap distance, dope extrusion rate, bore fluid flow rate, and the take‐up speed. The contact angle was measured to determine the hydrophilicity of the fibers. Membrane with sufficient hydrophilicity properties is desired for hemodialysis application to avoid fouling and increase its biocompatibility. The influences of the hollow fiber's morphology (i.e., diameter and wall thickness) on the performance of the membranes were evaluated by pure water flux and BSA rejection. The experimental results showed that the dope extrusion rate to bore fluid flow rate ratio should be maintained at 1:1 ratio to produce a perfectly rounded asymmetric hollow fiber membrane. Moreover, the flux of the hollow fiber spun at higher air gap distance had better flux than the one spun at lower air gap distance. Furthermore, spinning asymmetric hollow fiber membranes at high air gap distance helps to produce a thin and porous skin layer, leading to a better flux but a relatively low percentage of rejection for BSA separation. Findings from this study would serve as primary data which will be a useful guide for fabricating a high performance hemodialysis hollow fiber membrane. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43633.     

添加剂和凝结剂温度对用无溶剂致相位分离法生产高性能PVDF/聚醚F127混合中空光纤膜的影响(英文)

Poly(vinylidene fluoride)(PVDF) has become one of the most popular materials for membrane prepara-tion via nonsolvent induced phase separation(NIPS) process.In this study,an amphiphilic block copolymer,Plu-ronic F127,has been used as both a pore-former and a surface-modifier in the fabrication of PVDF hollow fiber membranes to enhance the membrane permeability and hydrophilicity.The effects of 2nd additive and coagulant temperature on the formation of PVDF/Pluronic F127 membranes have also been investigated.The as-spun hollow fibers were characterized in terms of cross-sectional morphology,pure water permeation(PWP),relative molecular mass cut-off(MWCO),membrane chemistry,and hydrophilicity.It was observed that the addition of Pluronic F127 significantly increased the PWP of as-spun fibers,while the membrane contact angle was reduced.However,the size of macrovoids in the membranes was undesirably large.The addition of a 2nd additive,including lithium chlo-ride(LiCl) and water,or an increase in coagulant temperature was found to effectively suppress the macrovoid for-mation in the Pluronic-containing membranes.In addition,the use of LiCl as a 2nd additive also further enhanced the PWP and hydrophilicity of the membranes,while the surface pore size became smaller.PVDF hollow fiber with a PWP as high as 2530 L?m?2?h?1?MPa?1,a MWCO of 53000 and a contact angle of 71° was successfully fabricated with 3%(by mass) of Pluronic F127 and 3%(by mass) of LiCl at a coagulant temperature of 25 °C,which shows better performance as compared with most of PVDF hollow fiber membranes made by NIPS method.     

The effects of carbonization temperature on the properties and structure of PAN‐based activated carbon hollow fiber

Polyacrylonitrile (PAN) hollow fibers were pretreated with ammonium dibasic phosphate and then further oxidized in air, carbonized in nitrogen, and activated with carbon dioxide. The effects of carbonization temperature of PAN hollow fiber precursor on the microstructure, specific surface, pore‐size distribution, and adsorption properties of PAN‐based carbon hollow fiber (PAN‐CHF) and PAN‐based activated carbon hollow fibers (PAN‐ACHF) were studied in this work. After the activation process, the surface area of the PAN‐ACHF increased very remarkably, reaching 900 m² g^?1 when carbonization is 1000°C, and the adsorption ratios to creatinine and VB₁₂ of ACHF were much higher than those of CHF, especially to VB₁₂. The different adsorption ratios to two adsorbates including creatinine and VB₁₂ reflect the number of micropores and mesopores in PAN‐ACHF. The dominant pore sizes of mesopores in PAN‐ACHF are from 2 to 5 nm. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 97: 2155–2160, 2005     

Improving bonding strength between a hydrophilic coating layer and poly(ethylene terephthalate) braid for preparing mechanically stable braid‐reinforced hollow fiber membranes

A braid‐reinforced hollow fiber membrane with mechanically stable coating layer was prepared by coating a blended polymer dope solution on an alkaline‐treated poly(ethylene terephthalate) (PET) braid. The alkaline treatment was carried out to endow the PET braid surface with more polar groups and better hydrophilicity. The results showed that the bonding strength between the hydrophilic coating layer and modified PET braid was about two times as great as that between the coating layer and original PET braid, while the pure water permeability (PWP) of the membrane remained unchanged when the PET braid was simply treated in 3 wt % potassium hydroxide (KOH) solution at 90 °C for 1 h or 1 wt % KOH solution for 6 h. The proposed modification approach proved to be a facile, low‐cost, and effective method to improve bonding strength between the coating layer and the braid, while other properties, such as PWP and morphology of the coating layer, of the braid‐reinforced hollow fiber membranes were not altered, indicating promising potential in membrane engineering. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 46104     

Grafting modification of electrospun polystyrene fibrous membranes via an entrapped initiator in an acrylic acid aqueous solution

Ultrafine electrospun polymer fibers, with their large specific surface areas, have not found wide applications partly because the fiber surfaces usually carry an insufficient quantity of active groups. The electrospinning and surface‐grafting copolymerization of polystyrene fibrous membranes were carried out via the embedded radical initiator approach. The results from X‐ray photoelectron spectroscopy show that the initiator added to the polystyrene dope was deliberately expelled onto the fiber surfaces. The microstructure and hydrophilicity of the grafted membranes were investigated with Fourier transform infrared spectroscopy, scanning electron microscopy, and water contact angle and water uptake capacity measurements. An increase in the initiator dosages led to decreases in the grafting rate, water uptake, and hydrophilicity of the grafted membranes; the opposite was true for increases in the neutralization of acrylic acid (AA). However, the grafting, water uptake, and hydrophilicity of the grafted membranes presented nonlinear relationships with the concentration of AA. The initiator emigration technique will provide a facile and feasible platform for the surface‐grafting modification of electrospun membranes. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Effect of the preparation conditions on the morphology and performance of poly(imide) hollow fiber membranes

Poly(imide) (PI) hollow fiber membranes were prepared by using classical phase inversion process. Effects of different external coagulation bath temperatures (ECBT) and various bore flow rates (BFR) on the morphology and separation performance of the membranes were studied. Cross‐section, inner and outer structures were characterized by using scanning electron microscope and atomic force microscopy (AFM). Mean pore size, pore size distribution, and mean roughness of the PI hollow fibers surfaces were estimated by AFM. It was found that the hollow fibers morphology composed of sponge‐like and finger‐like structures with different ECBT and BFR. A circular shape of the nodules with different sizes was observed in the outer surface of the PI hollow fibers. Mean pore size of the outer surface increases with increasing ECBT and BFR. The important result observed in this study is that the ECBT clearly has the largest effect on hollow fiber PI membrane roughness compared with the BFR. Pure water permeability of the PI hollow fibers was improved with increase of ECBT and BFR. The solute rejection (R%) was reduced when the ECBT and BFR was increased. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40428.     

Chemical grafting of curcumin at polyethylene terephthalate woven fabric surface using a prior surface activation with ultraviolet excimer lamp

Durable curcumin‐treated antibacterial polyethylene terephthalate (PET) fabrics (against Staphylococcus aureus) were produced by dyeing with curcumin after surface activation using vacuum ultraviolet excimer lamp at 172 nm. Surface change properties of the exposed fabrics were characterized by surface analysis methods such as wettability, atomic force microscopy, and X‐ray photoelectron spectroscopy. Results show an increase in surface hydrophilicity with a water contact angle of the PET fabric reaching 24° after 10 min excimer irradiation, which could be attributed to an increase in carboxyl group formation as confirmed by X‐ray photoelectron spectroscopy measurements. Varying concentrations of curcumin were immobilized onto untreated and vacuum ultraviolet‐irradiated PET samples using diffusion method at 90°C, and the treated fabrics characterized using K/S (color strength) values at 440 nm. K/S values increased when the PET surface was subjected to a prior excimer irradiation, because of grafting of curcumin at the PET surface. Increased excimer irradiation time increased grafting of curcumin because the inner fabric fiber surfaces were also more thoroughly treated. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Hydrophilic modification of poly(vinylidene fluoride) membrane with poly(vinyl pyrrolidone) via a cross‐linking reaction

A highly hydrophilic hollow fiber poly(vinylidene fluoride) (PVDF) membrane [PVDF‐cl‐poly(vinyl pyrrolidone) (PVP) membrane] was prepared by a cross‐linking reaction with the hydrophilic PVP, which was immobilized firmly on the outer surface and cross‐section of the PVDF hollow fiber membrane via a simple immersion process. The cross‐linking between PVDF and PVP was firstly verified via nuclear magnetic resonance measurement on PVP solution after cross‐linking. The hydrophilic stability of the modified PVDF membrane was evaluated by measuring the pure water flux after different times of immersion and drying. The anti‐fouling properties were estimated by cyclic filtration of protein solution. When the cross‐linking time was as long as 6 hr and the PVP content reached 5 wt %, the pure water flux (J_v) was constant as ～ 600 L m^?2 hr^?1. The hydrophilicity of the PVDF‐cl‐PVP membrane was significantly enhanced and exhibited a good stability. The PVDF‐cl‐PVP membrane showed an excellent anti‐protein‐fouling performance during the cyclic filtration of bovine serum albumin solution. Therefore, a highly hydrophilic and anti‐protein‐fouling PVDF hollow fiber membrane with a long‐term stability can be prepared by a simple and economical cross‐linking process with PVP. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Studies on high‐speed melt spinning of noncircular cross‐section fibers. II. On‐line measurement of the spin line,including change in cross‐sectional shape

On‐line measurement was performed in the high‐speed spinning of flat, hollow, and circular fibers of poly(ethylene terephthalate), paying particular attention to the change in cross‐sectional shape along the spin line. The diameter profiles of hollow and circular fibers were essentially identical, whereas the deformation of flat fiber shifted to the region closer to the spinneret. The necklike deformation of hollow and circular fibers started at the takeup velocity of 5 km/min. In the case of flat fibers, presence of the necklike deformation was confirmed at 4 km/min, and extremely steep diameter attenuation was observed at 5 km/min. The spin‐line tension of the flat fiber was also larger than that of circular fibers. Combined measurements of fiber velocity and thickness enabled us to evaluate the aspect ratio of the flat fiber and hollow ratio of the hollow fiber in the spin line. These two factors were found to decrease steeply near the spinneret. Accordingly, the thinning of the spin line and the change in cross‐sectional shape appeared to proceed independently. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 80: 1582–1588, 2001     

Temperature‐sensitive PVDF hollow fiber membrane fabricated at different air gap lengths

This article describes preparation of temperature‐sensitive poly(vinylidene fluoride) hollow fiber membranes using the dry‐wet spinning technique and investigates effects of air gap length on the structures and performances. In spinning these hollow fibers, N,N‐dimethyl formamide and poly(ethylene glycol) (10,000) were used as the solvent and pore‐forming agent, respectively. The prepared fiber membranes were characterized by scanning electron microscopy, pore size measurement, filtration experiments of pure water flux, and solutes with different molecular weights. The fiber membranes exhibit a quite asymmetric structures consisting of double skin layers situated on the fiber walls, two finger‐like layers near skin layers as well as macrovoids and sponge‐like structures at the center of the fiber cross‐sections. Remarkable changes of pure water flux and retention of solute are observed around 32°C, indicating an excellent temperature‐sensitive permeability. As the air gap length increases, the pore size of fiber membrane decreases, which results in decrease of pure water flux and allows small molecules to permeate through the fiber membrane. POLYM. ENG. SCI., 53:2519–2526, 2013. © 2013 Society of Plastics Engineers     

Influence of the cross‐sectional shape on the structure and properties of polyester fibers

The effects of the fiber cross‐sectional shape on the structure and properties of polyester fibers were investigated. Fully drawn yarn (FDY) polyester fibers (167 dtex and 48 filaments) were produced under the same spinning conditions used in a spinning plant. The only difference between the fibers was their cross‐sectional shapes. Four different cross‐sectional shapes were chosen for the experimental work: round, hollow‐round, trilobal, and hollow‐trilobal. The crystallinity and values of the maximum stress, maximum strain, modulus, yield stress, shrinkage in boiling water, and unevenness of the fibers were determined. The difference in the cross‐sectional shapes influenced the modulus, maximum strain, yield stress, and shrinkage in boiling water. No effects on the crystallinity and maximum stress were observed. The results suggested that the hollow fibers had higher amorphous orientation than the full fibers. The hollow‐round fiber had the highest unevenness value. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 103: 2615–2621, 2007