Effect of methyl methacrylate on the properties of transparent flame retardant unsaturated phosphate ester copolymer

The effect of methyl methacrylate (MMA) on the properties of transparent flame retardant unsaturated phosphate ester copolymer (poly[UPE‐co‐MMA]) prepared by bulk polymerization technique was investigated. Fourier transform infrared spectra, gel fraction (G) test, and dynamic mechanical analysis revealed the structure and crosslinking density of poly(UPE‐co‐MMA) copolymers. The thermal degradation and flame retardancy of copolymers were indicated by thermogravimetric analysis, limiting oxygen index (LOI), and microscale combustion calorimeter (MCC) test. Besides, the mechanical properties and transparency were tested with testing machines and solid ultraviolet absorption spectra. As the MMA content increased to 50%, the copolymer contained 50 wt% MMA showed the maximal G (88.93%) and transmittance was up to 91.72%. From the poly(UPE‐co‐MMA) copolymers, the tensile strength increased from 14.62 to 26.95 MPa, assigned to the increase of crosslinking density of copolymers. The char yield of poly(UPE‐co‐MMA) was up to 21.18 wt%, which was a result of decomposition of phosphate groups, producing a phosphorus‐rich layer that increased the thermal stability of the residues. LOI and MCC results confirm that the introduction of MMA can retain the flame retardancy of copolymer remarkably. POLYM. ENG. SCI., 59:2103–2109, 2019. © 2019 Society of Plastics Engineers     

Studies on blends of LLDPE and polar polymers compatibilized by a random copolymer

Compatibilization of blends of linear low‐density polyethylene (LLDPE)–poly(methyl methacrylate) (PMMA) and LLDPE–copolymer of methyl methacrylate (MMA) and 4‐vinylpyridine (poly(MMA‐co‐4VP) with poly(ethylene‐co‐methacrylic acid) (EMAA) have been studied. Mechanical properties of the LLDPE–PMMA blends increase upon addition of EMAA. In order to further improve interfacial adhesion of LLDPE and PMMA, 4‐vinyl pyridine units are introduced into PMMA chains, or poly(MMA‐co‐4VP) is used as the polar polymer. In LLDPE–poly(MMA‐co‐4VP)–EMAA blends, interaction of MAA in EMAA with 4VP of poly(MMA‐co‐4VP) causes a band shift in the infrared (IR) spectra. Chemical shifts of N_1s binding energy in X‐ray photoelectronic spectroscopy (XPS) experiments indicate a transfer of proton from MAA to 4VP. Scanning electron microscopy (SEM) pictures show that the morphology of the blends were improved upon addition of EMAA. Nonradiative energy transfer (NRET) fluorescence results attest that there exists interdiffusion of chromophore‐labeled LLDPE chains and chromophore‐labeled poly(MMA‐co‐4VP) chains in the interface. Based on experimental results, the mechanism of compatibilization is studied in detail. Compatibilization is realized through the interaction between MAA in EMAA with 4VP in poly(MMA‐co‐4VP). © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 71: 967–973, 1999     

Effect of surface functionalization on the physicomechanical properties of a novel biofunctional copolymer

The physicomechanical properties of functionally active poly(hydroxyethyl methacrylate‐co‐methyl methacrylate) [poly(HEMA‐co‐MMA)] are evaluated. It has been reported that the surface phosphorylated poly(HEMA‐co‐MMA) is capable of eliciting direct bone bonding when implanted in vivo. Hence, it is important to examine the physicomechanical property of the copolymer as a function of surface modification. The properties assessed are differential scanning calorimetry (DSC), thermogravimetric analysis (TGA), equilibrium swelling, compressive strength, and dynamic mechanical analysis. According to the DSC data, the glass transition temperature, T_g of poly(HEMA‐co‐MMA) is not significantly altered by surface phosphorylation. The TGA results demonstrated that unmodified and surface phosphorylated copolymers have similar degradation profile. The differential thermal analysis further supports the data. The equilibrium swelling of functionalized poly(HEMA‐co‐MMA) in phosphate buffer saline ascertained that surface phosphorylation significantly increased the hydrophilicity of the copolymer. The study further illustrated that the percentage of equilibrium swelling appreciably increases with increase in HEMA content in the copolymer and reached a plateau after 100 h. Both compressive strength and compressive modulus of poly (HEMA‐co‐MMA) decreased due to surface phosphorylation while dynamic storage modulus value was not altered. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Poly(N‐isopropylacrylamide) grafted to a strongly charged backbone: Thermoresponsive behavior in aqueous solution

The thermoresponsive properties in aqueous solution of the graft copolymer poly(acrylic acid‐co‐2‐acrylamido‐2‐methyl propane sulfonic acid)‐g‐poly(N‐isopropylacrylamide) [P(AA‐co‐AMPSA)‐g‐PNIPAM] were studied and compared to the corresponding behavior of the poly(acrylic acid)‐g‐poly(N‐isopropylacrylamide) (PAA‐g‐PNIPAM) graft product. Both products contain about 40% (w/w) of PNIPAM, whereas the backbone, P(AA‐co‐AMPSA), of the first copolymer contains about 40% of AMPSA mole units. The strongly charged P(AA‐co‐AMPSA)‐g‐PNIPAM graft copolymer was water soluble over the whole pH range, whereas the PAA‐g‐PNIPAM copolymer precipitated out from water at pH < 4. As a result, the first product exhibited a temperature‐sensitive behavior in a wide pH range, extended in the acidic region, whereas in semidilute aqueous solutions, an important thermothickening behavior was observed, even at low pH (pH = 3.0). © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 3466–3470, 2004     

Effect of the MMA content on the emulsion polymerization process and adhesive properties of poly(BA‐co‐MMA‐co‐AA) latexes

In the past work, the shear resistance of pure poly(n‐butyl acrylate) was low, even incorporation of inorganic filler, silica in the composition. It is well‐known that the copolymerization of n‐butyl acrylate (BA) with methyl methacrylate (MMA) will increase the glass transition temperature, and enhance the shear resistance of acrylic polymers. In the current work, the preparation of a series of acrylic water‐borne pressure‐sensitive adhesives (PSAs) with the controlled composition and structure for the copolymerization of BA and acrylic acid (AA) with different MMA contents, poly(BA‐co‐MMA‐co‐AA) was reported and its effects on adhesive properties of the latices were investigated. The latices of poly(BA‐co‐MMA‐co‐AA) were prepared at a solid content of 50% by two‐stage sequential emulsion polymerization, and this process consisted of a batch seed stage giving a particle diameter of 111 nm, which was then grown by the semicontinuous addition of monomers to final diameter of 303 nm. Dynamic light scattering (DLS) was used to monitor the particle diameters and proved that no new nucleation occurred during the growth stage. Copolymerization of BA with MMA raised the glass transition temperature (T_g) of the soft acrylic polymers, and had the effect of improving shear resistance, while the loop tack and peel adhesion kept relatively high. The relationship between pressure‐sensitive properties and molecular parameters, such as gel content and molecular weight, was evaluated. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Preparation and thermal response behavior of poly(N‐isopropylacrylamide‐co‐a crylic acid) microgels via soap‐free emulsion polymerization based on AIBN initiator

Poly(N‐isopropylacrylamide‐co‐acrylic acid) (poly(NIPAM‐co‐AA)) microgels with different copolymer compositions were prepared through soap‐free emulsion polymerization at 80°C, and 2, 2′‐azobisisobutyronitrile (AIBN) was used as initiator. Scanning electron microscope (SEM) characterization shows that the prepared microgels are regular and smooth and not easy to distort. Result of ¹H‐NMR characterization shows that with increasing of the initial concentration of AA (AA in feed), the AA content in polymer chains increases. The thermal response of microgels latex was investigated by UV‐3010 spectrophometer through detecting the transmittance of the latex at different temperature in the range of 190–900 nm. The thermal response of the poly(NIPAM‐co‐AA) microgels was tested by dynamic light scattering (DLS). The results show that with the increase of AA content in polymer chains, the low critical solution temperature (LCST) of microgels latex first decreases and then increases. Still, with increasing of AA in poly(NIPAM‐co‐AA) microgels, the LCST of microgels first increases and then decreases. The basic reasons causing the changes of LCST of microgels latex and microgels are interpreted clearly in this article from the perspective of hydrogen bonding interaction. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Synthesis and characterization of binary copolymers of methyl methacrylate with glycidyl methacrylate and 2‐hydroxy ethyl methacrylate as carriers for cellulase

Cellulase was immobilized directly on methyl methacrylate‐glycidyl methacrylate copolymer (MMA‐co‐GMA) and methyl methacrylate‐2‐hydroxy ethyl methacrylate copolymer (MMA‐co‐HEMA) by covalent attachment and crosslinking methods. The properties of the immobilized cellulase were investigated and compared with those of the free one. For the assays carried out through crosslinking method at 25°C and pH 7, the retained activities were found to be 91.92% and 74.63%, respectively, for MMA‐co‐GMA and MMA‐co‐HEMA crosslinked with 0.1% of 1‐cyclohexyl‐3‐(2‐morpholino‐ethyl) carbodiimide metho‐p‐toluenesulfonate (CMCT), respectively. The immobilized cellulase had better stability and higher retained activities with respect to pH, temperature, and storage stability than the free one. In the repeated use experiments, the immobilized cellulase using (MMA‐co‐GMA)‐CMCT (0.1%) and (MMA‐co‐HEMA)‐CMCT (0.1%) did not change after 10 and eight times of repeated use and maintained 67% and 62% from their original activities after 25 times, respectively. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Synthesis and characterization of poly(HEMA‐co‐MMA)‐g‐POSS nanocomposites by combination of reversible addition fragmentation chain transfer polymerization and click chemistry

New hybrid poly(hydroxyethyl methacrylate‐co‐methyl methacrylate)‐g‐polyhedral oligosilsesquioxane [poly(HEMA‐co‐MMA)‐g‐POSS] nanocomposites were synthesized by the combination of reversible addition fragmentation chain transfer (RAFT) polymerization and click chemistry using a grafting to protocol. Initially, the random copolymer poly(HEMA‐co‐MMA) was prepared by RAFT polymerization of HEMA and MMA. Alkynyl side groups were introduced onto the polymeric backbones by esterification reaction between 4‐pentynoic acid and the hydroxyl groups on poly(HEMA‐co‐MMA). Azide‐substituted POSS (POSS? N₃) was prepared by the reaction of chloropropyl‐heptaisobutyl‐substituted POSS with NaN₃. The click reaction of poly(HEMA‐co‐MMA)‐alkyne and POSS? N₃ using CuBr/PMDEATA as a catalyst afforded poly(HEMA‐co‐MMA)‐g‐POSS. The structure of the organic/inorganic hybrid material was investigated by Fourier transformed infrared, ¹H‐NMR, and ²⁹Si‐NMR. The elemental mapping analysis of the hybrid using X‐ray photoelectron spectroscopy and EDX also suggest the formation of poly(HEMA‐co‐MMA)‐anchored POSS nanocomposites. The XRD spectrum of the nanocomposites gives evidence that the incorporation of POSS moiety leads to a hybrid physical structure. The morphological feature of the hybrid nanocomposites as captured by field emission scanning electron microscopy and transmission electron microscopic analyses indicate that a thick layer of polymer brushes was immobilized on the POSS cubic nanostructures. The gel permeation chromatography analysis of poly(HEMA‐co‐MMA) and poly(HEMA‐co‐MMA)‐g‐POSS further suggests the preparation of nanocomposites by the combination of RAFT and click chemistry. The thermogravimetric analysis revealed that the thermal property of the poly(HEMA‐co‐MMA) copolymer was significantly improved by the inclusion of POSS in the copolymer matrix. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Preparation and characterization of photoreactive copolymers containing curable pendants for positive photoresist

tert‐Butyl methacrylate (TBMA) was copolymerized with various comonomers that were selected from methyl methacrylate (MMA), n‐butyl acrylate (NBA), acrylic acid (AA), and 2‐hydroxyethyl methacrylate (HEMA). From film physical properties, poly(TBMA‐co‐HEMA) and poly(TBMA‐co‐AA‐co‐NBA), were selected as resin binders. To introduce unsaturated double bonds onto the side chain of copolymers, they were further functionalized with acryloyl chloride and glycidyl methacrylate. Copolymers synthesized in this investigation were all identified by using FTIR and NMR. The thermal decomposition temperature of functionalized poly(TBMA‐co‐HEMA) showed obvious difference before and after crosslinking. Adding a small amount of EGDMA as the crosslinking agent could increase the degree of crosslinking and obviously improve the physical properties. Functionalized poly(TBMA‐co‐HEMA) was used as a binder resin and composed with a photoacid generator for positive photoresists. From exposure characteristics, the optimal lithographic condition was achieved when exposed for 90 s, PEB at 100°C for 2.5 min, and developed in 10 wt % Na₂CO₃ developer for 30 s. After completing the lithography process, the residual pattern of positive photoresist was further treated at 140°C for 30 min to cure the pendant unsaturated groups. The resolution of the positive photoresist was analyzed by an optical microscope and SEM technique. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 80: 328–333, 2001     

Star graft copolymer via grafting‐onto strategy using a comb!ination of reversible addition–fragmentation chain transfer arm‐first technique and aldehyde–aminooxy click reaction

A facile synthetic pathway to a multi‐arm star graft polymer has been developed via a grafting‐onto strategy using a combination of a reversible addition–fragmentation chain transfer (RAFT) arm‐first technique and aldehyde–aminooxy click reaction. A star backbone bearing aldehyde groups was prepared by the RAFT copolymerization of acrolein (Ac), an existing commercial aldehyde‐bearing monomer, with styrene (St), followed by crosslinking of the resultant poly(St‐co‐Ac) macro‐RAFT agent using divinylbenzene. The aldehyde groups on the star backbone were then used as clickable sites to attach poly(ethylene glycol) (PEG) side chains via the click reaction between the aldehyde groups and aminooxy‐terminated PEG, leading to a structurally well‐defined star graft copolymer with arms consisting of poly(St‐co‐Ac) as backbone and PEG as side chains. Crystalline morphology and self‐assembly in water of the obtained star graft copolymer were also investigated. Opportunities are open for the star graft copolymer to form either multimolecular micelles or unimolecular micelles via control of the number of grafted PEG side chains. © 2013 Society of Chemical Industry     

Preparation of a structured acrylic impact modifier and its application in toughening polyamide 6

A series of poly(n‐butyl acrylate)/poly(methyl methacrylate‐co‐acrylic acid), i.e., poly(BA/MMA‐co‐AA), core‐shell structured modifiers with different contents of crosslinking agent allyl methacrylate and functional monomer were prepared, and its effects on mechanical properties of polyamide 6 (PA 6) blends were investigated. The modifiers were prepared at a solid content of 50 wt% by a seeded emulsion polymerization. Dynamic light scattering measurement showed that the particle grew without significant secondary nucleation occurring. The morphology was confirmed by means of transmission electron microscopy. Scanning electron microscopy was used to observe the morphology of the fractured surfaces. The dynamic mechanical analysis measurements indicated that the appearance of two merged transition peaks and the magnitude of the loss peak of PA 6 matrix with the addition of PBMA core‐shell modifier in the PA 6/PBMA blends were responsible for the improvement of PA 6 toughness. POLYM. ENG. SCI., 2012. © 2011 Society of Plastics Engineers     

Synthesis of an acrylate elastomer with UV stabilization and its application in polyoxymethylene

In this study, an acrylate elastomer with light‐stable functional groups was synthesized by methyl methacrylate (MMA), butyl acrylate (BA), and a polymerizable UV stabilizer 2‐hydroxy‐4‐(3‐methacryloxy‐2‐hydroxylproroxy) benzophenone (BPMA) via emulsion polymerization, and the product was poly[methyl methacrylate‐co‐butyl acrylate‐co‐2‐hydroxy‐4‐(3‐methacryloxy‐2‐hydroxylproroxy) benzophenone] [poly(MMA‐co‐BA‐co‐BPMA)]. The composition and characteristics of poly (MMA‐co‐BA‐co‐BPMA) were determined by using Fourier transform infrared spectroscopy (FTIR), proton nuclear magnetic resonance (¹H‐NMR), and ultraviolet–visible absorption spectroscopy (UV–vis). Further, the obtained poly(MMA‐co‐BA‐co‐BPMA) was blended with polyoxymethylene (POM) to modify its photostabilization, as well as the mechanical properties of POM composite were tested before and after UV irradiation. The result showed that poly(MMA‐co‐BA‐co‐BPMA) can be dispersed well in the POM matrix, which could play a role of improving compatibility with and toughening for POM, and its light‐stable functional groups could increase the UV resistance of POM composite. Mechanical properties of modified POM were kept well with higher impact strength and elongation at break than pure POM after UV irradiation. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

One‐pot synthesized poly(vinyl pyrrolidone‐co‐methyl methacrylate‐co‐acrylic acid) blended with poly(ether sulfone) to prepare blood‐compatible membranes

In this study, a random copolymer of poly(vinyl pyrrolidone‐co‐methyl methacrylate‐co‐acrylic acid) was synthesized via a one‐pot reaction with the reversible addition–fragmentation chain‐transfer method and was then blended with poly(ether sulfone) (PES) to prepare flat‐sheet membranes that were expected to have anticoagulant and antifouling properties. The synthesized copolymer was characterized by Fourier transform infrared (FTIR) and NMR spectroscopy. The molecular weights and molecular weight distributions were determined by gel permeation chromatography. Elemental analysis was used to calculate the molar ratios of vinyl pyrrolidone (VP), methyl methacrylate (MMA), and acrylic acid (AA) in the copolymer. A liquid–liquid phase‐inversion technique was used to prepare the copolymer‐blended PES membranes. X‐ray photoelectron spectroscopy and attenuated total reflectance–FTIR spectroscopy were used to investigate the copolymer on the membrane surfaces. Compared with the pristine PES membrane, the modified PES membranes showed improved hydrophilicity, low hemolysis ratios, decreased protein adsorption, and suppressed platelet adhesion. Furthermore, the thrombin time and activated partial thromboplastin time indicated that the blood compatibility of the modified PES membranes were improved. The results of the 3‐(4,5‐Dimethylthiazol‐2‐yl)‐2,5‐diphenyltetrazolium bromide (MTT) assay and the cell morphology suggested that the cytocompatibility increased. In addition, the modified membranes showed good protein antifouling properties. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 130: 4284–4298, 2013     

Morphologies of polybutylacrylate/poly(styrene‐co‐methyl methacrylate) latex prepared by starved emulsion polymerization Part I. Thermodynamics equilibrium morphology

Heterogeneous latexes were prepared by a semicontinuous seeded emulsion polymerization process under monomer starved conditions at 80 °C using potassium persulfate as the initiator and sodium dodecyl sulfate as the emulsifier. Poly(butyl acrylate) latexes were used as seeds. The second‐stage polymer was poly(styrene‐co‐methyl methacrylate). By varying the amounts of methyl methacrylate (MMA) in the second‐stage copolymer, the polarity of the copolymer phase could be controlled. Phase separation towards the thermodynamic equilibrium morphology was accelerated either by ageing the composite latex at 80 °C or by adding a chain‐transfer agent during polymerization. The morphologies of the latex particles were examined by transmission electron microscopy (TEM). The morphology distributions of latex particles were described by a statistical method. It was found that the latex particles displayed different equilibrium morphologies depending on the composition of the second‐stage copolymers. This series of equilibrium morphologies of [poly(butyl acrylate)/poly(styrene‐co‐methyl methacrylate)] (PBA/P(St‐co‐MMA)) system provides experimental verification for quantitative simulation. Under limiting conditions, the equilibrium morphologies of PBA/P(St‐co‐MMA) were predicted according to the minimum surface free energy change principle. The particle morphology observed by TEM was in good agreement with the predictions of the thermodynamic model. Therefore, the morphology theory for homopolymer/homopolymer composite systems was extended to homopolymer/copolymer systems. © 2002 Society of Chemical Industry     

HEMA‐Modified Expandable P(MMA‐AA) Bone Cement with Dual Water Absorption Networks

Although the shrinkage of polymethyl methacrylate (PMMA) bone cement has been tackled by the poly(methyl methacrylate‐co‐acrylic acid) [P(MMA‐AA)] bone cement due to the expandable P(MMA‐AA) copolymer in the solid phase, the hydrophobicity of PMMA and its solidification restrict simulated body fluid (SBF) diffusion and expansion properties. In this research, hydroxyethyl methacrylate (HEMA)‐modified P(MMA‐AA) bone cement (HMBC) is obtained by introducing HEMA into the liquid phase of P(MMA‐AA) bone cement. It is assumed that the dual water absorption networks can promote the SBF absorption capacity, thus resulting in the increased expansion behavior. The results demonstrate that the introduction of HEMA improves the hydrophilicity of the bulk. SBF absorption efficiency and swelling efficiency are promoted in the primary step of expansion. The porous structure of HMBC contributes to the increased SBF absorption and swelling in the second step of expansion behavior. Meanwhile, the remarkable absorption ratio and expansion ratio reach 88.5% and 97.4%, respectively. Furthermore, enhanced biocompatibility and osteogenesis activity provide HMBC as a promising biomaterial in the clinical setting.     

Investigation for surface morphology and mechanical property variations of single polymer particles

Monodisperse polymer particles were prepared via one‐step seeded polymerization using polystyrene, poly(methyl methacrylate), or styrene/methyl methacrylate copolymer [poly(ST‐co‐MMA)] as seed particles and 1,6‐hexanedioldiacrylate or divinylbenzene as crosslinking monomer. For the study, the effects of the combination of seed polymer and crosslinking monomer, the ratio of the absorbed monomer to the seed polymer particles (swelling ratio: S/R), and the seeded polymerization rate on the variation of surface morphology and mechanical properties of polymer particles, such as recovery rate, K‐values, breaking strength, and breaking displacement were investigated by using microcompression test. It was observed that the surface morphology could be controlled by changing polymerization rate or combination of seed polymer and crosslinking monomer, and it had a great influence on mechanical properties, especially the breaking strength. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 104: 2350–2360, 2007     

Blends of poly(vinyl chloride) (PVC)/natural rubber‐g‐(styrene‐co‐methyl methacrylate) for improved impact resistance of PVC

To improve the mechanical properties of poly(vinyl chloride) (PVC), the possibility of combining PVC with elastomers was considered. Modification of natural rubber (NR) by graft copolymerization with methyl methacrylate (MMA) and styrene (St) was carried out by emulsion polymerization by using redox initiator to provide an impact modifier for PVC. The impact resistance, dynamic mechanical analysis (DMA), and scanning electron microscopy (SEM) of St and MMA grafted NR [NR‐g‐(St‐co‐MMA)]/PVC (graft copolymer product contents of 5, 10, and 15%) blends were investigated as a function of the amount of graft copolymer product. It was found that the impact strength of blends was increased with an increase of the graft copolymer product content. DMA studies showed that NR‐g‐(St‐co‐MMA) has partial compatibility with PVC. SEM confirmed a shift from brittle failure to ductility with an increase graft copolymer content in the blends. The mechanical properties showed that NR‐g‐(St‐co‐MMA) interacts well with PVC and can also be used as an impact modifier for PVC. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 93: 1666–1672, 2004     

Synthesis,effectiveness, and working mechanism of humic acid‐{sodium 2‐acrylamido‐2‐methylpropane sulfonate‐co‐N,N‐dimethyl acrylamide‐co‐acrylic acid} graft copolymer as high‐temperature fluid loss additive in oil well cementing

Monomers of 2‐acrylamido‐2‐methylpropane sulfonic acid (AMPS®), N,N–dimethyl acrylamide (NNDMA) and acrylic acid (AA) were grafted on humic acid as backbone by aqueous free radical copolymerization in such a manner that a graft copolymer possessing lateral terpolymer chains was obtained. Molar ratios between AMPS®, NNDMA, and AA were found to be 1 : 1.54 : 0.02 and the ratio between backbone and graft chain was 20 : 80 wt %. The synthesized fluid loss additive (FLA) was characterized by size exclusion chromatography (SEC), charge titration, and Brookfield viscometry. Thermogravimetric and SEC analysis revealed stretched backbone worm architecture for the polymer whereby humic acid constitutes the backbone decorated with lateral graft chains. Grafting was confirmed by SEC data (R_g) and by ineffectiveness of a blend of AMPS®‐NNDMA‐AA copolymer with humic acid. Their performance as high temperature FLA was studied at 150°C by measuring static filtration properties of oil well cement slurries containing 35% bwoc of silica fume and 1.2% bwoc AMPS®‐co‐itaconic acid retarder. At this temperature, 1.0% bwoc graft copolymer achieves API fluid loss value of 40 mL, thus confirming high effectiveness. The graft copolymer viscosifies cement slurries less than other common synthetic FLAs. The working mechanism of the graft copolymer was found to rely on adsorption onto surface of hydrating cement, as was evidenced by adsorption and zeta potential measurements. Adsorption is hardly affected by temperature and results in constriction of the filter cake pores. The study provides insight into performance of cement additives under the harsh conditions of high temperature and high pressure. © 2012 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Synthesis and characterization of acrylamide‐based aluminum flocculant for turbidity reduction in wastewater

Polymeric flocculants of aluminum hydroxide‐poly[acrylamide‐co‐(acrylic acid)], AHAMAA, were prepared by solution polymerization using aluminum hydroxide as a coagulant in the presence of acrylamide (AM) and acrylic acid (AA) as a comonomer pair with N,N′‐methylenebisacrylamide as a crosslinking agent. The crosslinking was initiated by ammonium persulfate with N,N,N′,N′‐tetramethylethylenediamine as an initiator. The water absorbency of crosslinked poly[AM‐co‐AA] was always higher than that of AHAMAA and was found to be correlated to the storage modulus of the polymers, which was higher for AHAMAA than that of crosslinked poly[AM‐co‐AA]. The residual aluminum concentration of AHAMAA (0.09–0.2 mg L^?1) indicated the stability of the polymer flocculant which was in good agreement with the observed tan δ and the higher G′′ and G′ values. Both the crosslinked poly[AM‐co‐AA] and AHAMAA satisfactorily reduced the turbidity of kaolin suspensions, but the latter gave a better reduction performance. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Preparation and biodegradation of hydroxyl terminated poly(fumaric acid‐co‐diethylene glycol) and its segmented polyurethane

Hydroxyl terminated poly(fumaric acid‐co‐diethylene glycol), poly(FA‐co‐DEG) was prepared by melt polycondensation. The resultant unsaturated aliphatic polyester was characterized by Fourier transform infrared (FTIR) spectroscopy, hydroxyl value, acid value, and intrinsic viscosity. Its enzymatic degradation and crosslinking behavior as well as the effect of crosslinking degree on enzymatic degradation were also investigated. The crosslinking degree and reduction of carbon–carbon double bonds revealed excellent self‐crosslinking nature of poly(FA‐co‐DEG) at high temperature. The results of enzymatic degradation showed that poly(FA‐co‐DEG) has excellent biodegradability and that the biodegradation can be controlled by the crosslinking degree. Polyurethane was prepared by the reaction of poly(FA‐co‐DEG), 2,4‐toluene diisocyanate (TDI), and 1,4‐butanediol (BD). It was found that the biodegradation of the obtained polyurethane was slower than that of the original unsaturated aliphatic polyester poly(FA‐co‐DEG). The peeling strength of the polyurethane was very high, supporting better adhesion property with enhanced crosslinking. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011