Morphology and rheological behavior of maltene–polymer blends. I. Effect of partial hydrogenation of poly(styrene‐block‐butadiene‐block‐styrene‐block)‐type copolymers

Because of the importance of the maltene–polymer interaction for the better performance of polymer‐modified asphalts, this article reports the effects of the molecular characteristics of two commercial poly(styrene‐block‐butadiene‐block‐styrene‐block) (SBS) polymers and their partially hydrogenated derivatives [poly{styrene‐block[(butadiene)_1?x–(ethylene‐co‐butylene)_x]‐block‐styrene‐block} (SBEBS)] on the morphology and rheological behavior of maltene–polymer blends (MPBs) with polymer concentrations of 3 and 10% (w/w). Each SBEBS and its parent SBS had the same molecular weight and polystyrene block size, but they differed from each other in the composition of the elastomeric block, which exhibited the semicrystalline characteristics of SBEBS. Maltenes were obtained from Ac‐20 asphalt (Pemex, Salamanca, Mexico), and the blends were prepared by a hot‐mixing procedure. Fluorescence microscopy images indicated that all the blends were heterogeneous, with polymer‐rich and maltene‐rich phases. The rheological behavior of the blends was determined from oscillatory shear flow data. An analysis of the storage modulus, loss modulus, complex modulus, and phase angle as a function of the oscillatory frequency at various temperatures allowed us to conclude that the maltenes behaved as pseudohomogeneous viscoelastic materials that could dissipate stress without presenting structural changes; moreover, all the MPBs were more viscoelastic than the neat maltenes, and this depended on both the characteristics and amount of the polymer. The MPBs prepared with SBEBS were more viscoelastic and possessed higher elasticity than those prepared with SBS. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Rheological study of crosslinking and gelation in bismaleimide/cyanate ester interpenetrating polymer network

In searching for high performance polymer resins that have a combination of low dielectric constant and loss, high temperature resistance, ease of being processed, and other desirable properties, an interpenetrating polymer network (IPN) based on cyanate ester (CE) and 2,2′‐diallylbisphenol A (DBA) modified bismaleimide resin (BMI) was prepared via prepolymerization followed by thermal curing. This work discusses the use of multiple waveform rheological technique to investigate the crosslinking and gelation behavior of this resin system at various temperatures. The gel point can be accurately determined from a single experiment using this technique. At the point of gelation, both the storage modulus (G′) and loss modulus (G″) of the IPN follow a similar power law equation with oscillation frequency used in the rheological measurement. Both the relaxation exponent n, a viscoelastic parameter related to the cluster size of the gel, and gel strength S, related to the mobility of the crosslinked chain segments, were determined via a curve fitting method. Both n and S were found to be temperature dependent in this BMI/DBA–CE IPN system. The apparent activation energy of gelation or curing reaction was found to be approximately 47.6 kJ/mol. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 80: 2437–2445, 2001     

Viscoelastic sol–gel state of the chitosan and alginate solution mixture

The rheological behavior of chitosan/alginate solutions was investigated in relation to gelation and polyelectrolyte complex (PEC) formation. Before mixing, the chitosan and the alginate solutions were both homogeneous fluids. However, heterogeneity developed after mixing, accompanied by a serious increase of viscosity. To determine the sol–gel state of the solutions, the viscoelastic variables, such as the dynamic storage modulus (G′) and loss modulus (G″), the loss tangent, and the viscoelastic exponents for G′ and G″, were obtained. Depending on the concentration, the chitosan/alginate solutions revealed unexpected rheological behavior. At a polymer concentration of 1.0 wt %, the chitosan/alginate solution was in a viscoelastic gel state, whereas, at higher concentrations, viscoelastic sol properties were dominant. A viscoelastic gel state for the chitosan/alginate solution was induced based on the weak formation of fiber‐shaped precipitates of a PEC at a low polymer concentration. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 104: 1408–1414, 2007     

Melt rheology and properties of compatibilized recycled poly(ethylene terephthalate)/(styrene‐ethylene‐ethylene‐propylene‐styrene) block copolymer blends

Blends of recycled poly(ethylene terephthalate) (R‐PET) and (styrene‐ethylene‐ethylene‐propylene‐styrene) block copolymer (SEEPS) compatibilized with (maleic anhydride)‐grafted‐styrene‐ethylene‐butylene‐styrene (SEBS‐g‐MAH) were prepared by melt blending. The compatibilizing effects of SEBS‐g‐MAH were investigated systematically by study of the morphology, linear viscoelastic behavior, and thermal and mechanical properties of the blends. The results show that there is good agreement between the results obtained by rheological measurement and morphological analysis. The rheological test shows that the melt elasticity and melt strength of the blends increase with the addition of SEBS‐g‐MAH. The Cole‐Cole plots and van Gurp‐Palmen plots confirm the compatibilizing effect of SEBS‐g‐MAH. However, the Palierne model fails to predict the linear viscoelastic properties of the blends. The morphology observation shows that all blends exhibit a droplet‐matrix morphology. In addition, the SEEPS particle size in the (R‐PET)/SEEPS blends is significantly decreased and dispersed uniformly by the addition of SEBS‐g‐MAH. Differential scanning calorimeter analysis shows that the crystallization behavior of R‐PET is restricted by the incorporation of SEEPS, whereas the addition of SEBS‐g‐MAH improves the crystallization behavior of R‐PET compared with that of uncompatibilized (R‐PET)/SEEPS blends. The Charpy impact strength of the blends shows the highest value at SEBS‐g‐MAH content of 10%, which is about 210% higher than that of pure R‐PET. J. VINYL ADDIT. TECHNOL., 22:342–349, 2016. © 2014 Society of Plastics Engineers     

Use of rheological compatibility criteria to study SBS modified asphalts

Polymer‐modified asphalts (PMAs) were prepared using Bachaquero asphalt and styrene–butadiene–styrene (SBS) type copolymers. Their rheological behavior was compared to that of unmodified asphalt and of a compatible commercial PMA. Materials were submitted to frequency sweeps between 10^?1 and 10² rad/s from 0 to 50°C. Storage stability tests were performed for 72 h at 160°C. Ring and ball softening points from the top and the bottom of the blends were compared and were used along with fluorescence microscopy to evaluate stability. Samples prepared with styrene–ethylene–butylene–styrene (SEBS) showed improved compatibility and stability as compared with SBS‐modified asphalts, probably because of a higher stability to thermal degradation from the absence of double bonds. An additional improvement in stability and compatibility was observed for SEBS functionalized with maleic anhydride (SEBS‐g‐MAH)–modified blends. Better compatibility, however, did not improve rheological behavior at low temperatures. The systems studied are so complex from a chemical point of view that the rheological criteria normally used to predict compatibility of polyblends did not give enough information regarding the compatibility of the modified asphalts. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 1772–1782, 2003     

Morphology and rheology relationships of epoxy/core‐shell particle blends

The morphological and rheological behaviors of toughened epoxy resins modified with core‐shell rubber particles (CSR) were studied. These rubber particles were based on a poly (butadiene‐co‐styrene) core and a crosslinked poly (methyl methacrylate) shell. The effect of functionalized groups was performed on two types of CSR particles: first, those containing carboxyl‐functionalized groups (CSf), and second, particles containing no carboxyl‐functionalized groups (CSnf) in the PMMA‐shell. For these blends, the correlations between the morphology, particle dispersion state and their rheological behaviors before curing were investigated. Preliminary work using TEM micrographs indicated that the blends modified with CSf and CSnf exhibited the same particle size but differed with respect to the dispersion state. Rheological behavior of these blends was assessed in steady shear flow and dynamic viscoelastic experiments. Yield viscosity near‐zero shear rate occurred in the DGEBA/CSf blend presenting non‐Newtonian behavior at the particle volume fraction of 20% vol. The rheological behavior was clearly related to the state of particle dispersion and analyzed taking into account interactions between the particles‐particles and the particles‐matrix. The Williams‐Landel‐Ferry (WLF) shift procedure was used to construct modulus master curves G′ and G″ from the elastic solid state to molten polymers. A secondary plateau existed at low frequencies and was related to the presence of interactions leading to a physical network‐type structure. The deviation between theoretical G′ (Paleirne's model) and experimental G′ values was evaluated and exhibited high elasticity at the terminal zone, which correlated well with available literature.     

The linear viscoelastic behaviors of Nylon1212 blends toughened with elastomer

The linear viscoelastic behaviors of nylon1212 blends toughened with (styrene‐[ethylene‐(ethylene‐propylene)]‐styrene block copolymer) (SEEPS) elastomer were carried out. The results show that dynamic storage modulus (G′) curves of the blends are located between those of virgin nylon and SEEPS within the frequency (ω) tested, and the G′ of blends increases with increasing of the SEEPS content. Moreover, the predictive results of Palierne emulsion model show that it is unsuitable for describing the viscoelastic behaviors of the double phase systems toughened with elastomer, especially for the system with high content of elastomer. The positive deviation in the plots of G′ vs. blend composition demonstrates that the blends are immiscible. From the point of phase transition, the phase inversion region for these blends was predicted to be in the range of 30–50 wt % of SEEPS, which agrees with the morphology analysis of nylon1212/SEEPS blends. In addition, “Cole–Cole” plots of modulus at different temperatures show that the microstructures of blends are unstable in the phase transition region. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Structure and properties of heat‐resistant ABS resins innovated by NSM random copolymer

N‐phenylmaleimide(NPMI)‐styrene(St)‐maleic anhydride (MAH) copolymer was synthesized in xylene solution by one‐step free radical copolymerization, using di‐tert‐butyl diperoxyterephthalate as initiator. The resulting heat‐resistant NPMI‐St‐MAH (NSM) copolymer was characterized by Fourier transform infrared spectroscopy (FTIR), gel permeation chromatography, differential scanning calorimetry, elemental analysis, and nuclear magnetic resonance spectroscopy (¹H‐NMR and ¹³C‐NMR). The results show that NPMI‐St‐MAH exhibits a random sequence distribution with a NPMI: St: MAH weight ratio of 47:51:2. The glass transition temperature (T_g) is about 190.0°C. Blends of acrylonitrile‐butadiene‐styrene (ABS) with various contents of NSM were prepared using a twin‐screw extruder, and the effects of NSM content on the thermal and mechanical properties of ABS blends were investigated. It was found that the Vicat softening point, tensile strength, flexural strength, flexural modulus, and Rockwell hardness of the ABS/NSM blends were all significantly enhanced with increasing NSM content, whereas the impact strength shows the opposite trend. The impact fracture surface morphology was characterized by scanning electron microscope. It was revealed that cavitation and cavity coalescence resulted in the toughening of the material, which well accounts for the decrease of impact strength with increasing NSM content. In addition, the rheological properties of the blends were examined using a capillary rheometer. The blends present excellent processing property and are suitable for injection molding, although a pseudoplastic behavior was observed in all cases. POLYM. COMPOS., 34:920–928, 2013. © 2013 Society of Plastics Engineers     

Investigation on the correlation between rheology and morphology of PA6/ABS blends using ethylene acrylate terpolymer as compatibilizer

Phase morphology and rheological behavior of polyamide 6 (PA6)/acrylonitrile butadiene styrene (ABS) polymers blends was studied using scanning electron microscopy and rheometry. The results showed that the phase morphology and rheological properties depends on blend composition. We evaluated the effect of addition of ABS as dispersed phase and EnBACO‐MAH (ethylene n‐butyl acrylate carbon monoxide maleic anhydride) as a compatibilizer on the morphological and rheological behaviors of PA6/ABS blends. It was concluded that there is a good agreement between the results obtained from rheological and morphological studies. As a consequence, addition of the ABS and compatibilizer weight percent led to a significant change in morphological structure and a great mounting in the viscosity as well as the elasticity. The rheological properties results demonstrate that adding compatibilizer to polymer blends led to increasing the crossover point, which shows a transition from a high viscous to a considerably more elastic behavior. Also, the slow transition of relaxation time peak from the peak of the PA6 to the peak of the ABS implies increasing the miscibility of the PA6/ABS blend components by increasing compatibilizer content. In addition, the Carreau–Yasuda model was used to extract information on rheological properties (zero shear viscosity and relaxation time) for PA6/ABS/EnBACO‐MAH blends by fitting the experimental data with this model. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Compatibilizing effect of ethylene–propylene–diene grafted maleic anhydride terpolymer on the blend of polyamide 66 and thermal liquid crystalline polymer

Polyamide 66–thermal liquid crystalline polymer (PA66/TLCP) composites containing 10 wt% TLCP was compatibilized by ethylene–propylene–diene‐grafted maleic anhydride terpolymer (MAH‐g‐EPDM). The blending was performed on a twin‐screw extrusion, followed by an injection molding. The rheological, dynamic mechanical analysis (DMA), thermal, mechanical properties, as well as the morphology and FTIR spectra, of the blends were investigated and discussed. Rheological, DMA, and FTIR spectra results showed that MAH‐g‐EPDM is an effective compatibilizer for PA66/TLCP blends. The mechanical test indicated that the tensile strength, tensile elongation, and the bending strength of the blends were improved with the increase of the content of MAH‐g‐EPDM, which implied that the blends probably have a great frictional shear force, resulting from strong adhesion at the interface between the matrix and the dispersion phase; while the bending modulus was weakened with the increase of MAH‐g‐EPDM content, which is attributed to the development of the crystalline phase of PA66 hampered by adding MAH‐g‐EPDM. POLYM. COMPOS., 27:608–613, 2006. © 2006 Society of Plastics Engineers     

Properties of new nanocomposite triblock copolymer gels based on expandable graphite

In this work, we investigated the effect of expandable graphite (EG) on the property of triblock copolymer prepared from a poly(styrene‐b‐(ethylene‐co‐butylene)‐b‐styrene) (SEBS) imbibed with an EB‐compatible hydrocarbon oil. The rheological properties showed that at a temperature between 30 and 40°C below the gel point, the triblock copolymer gels had a dynamic storage modulus (G′) greater than loss modulus (G‵), thereby indicating that at ambient temperature, a physical network is still present in spite of the addition of nanoparticles. Dynamic rheological measurements of the resultant nanocomposite triblock copolymer gels confirmed that the addition of EG affects the linear viscoelastic properties and maximum operating temperature of the parent triblock copolymer gels. The mechanical properties showed only marginal increase, which can be attributed to the poor dispersion that leads to agglomeration of particle into micrometer size stacks, and thus the particles behave only as inorganic fillers. The morphology and X‐ray diffraction revealed that the EG used to generate nanocomposite triblock copolymer gels is dispersed generally within the swollen copolymer and/or solvent. POLYM. ENG. SCI., 2008. © 2008 Society of Plastics Engineers     

Rheological properties of syndiotacticity-rich ultrahigh molecular weight poly(vinyl alcohol) dilute solution

Viscoelastic behavior of the dilute solution of ultrahigh molecular weight syndiotactic poly(vinyl alcohol) (UHMW s-PVA)/dimethyl sulfoxide (DMSO)/water was investigated through rheological response. Below a critical temperature, the dynamic storage modulus (G′) of the solution became greater than the dynamic loss modulus (G″) and the viscoelastic exponent for G′ became smaller than that for G″ before macroscopic gelation, which indicates the evolution of viscoelastic solid properties at the sol state. Also, the loss tangent (tan δ) of the solution below the critical temperature increased with increasing frequency. Consequently, the dilute solution of UHMW s-PVA/DMSO/water showed the rheological behaviors as can be observed in general chemical or physical gel systems below the critical temperature. These results suggest that solid-like heterogeneity prevailed in the solution before macroscopic gelation with decreasing temperature. Such heterogeneity was considered as phase-separated domains attributed to spinodal decomposition. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 82: 569–576, 2001     

Gelation studies on acrylic acid‐based hydrogels via in situ photo‐crosslinking and rheology

The gelation characteristics of acrylic acid (AA)‐based hydrogels were investigated using real time in situ photocrosslinking and rheological measurements. The gel point and gelation times were established using Winter–Chambon criteria. Frequency independence of tan δ was observed in all cases, such that G′ and G″ scaled as ～ωⁿ. The Flory–Stockmayer theory was used alongside other indices in order to probe the gelation and the post‐gelation characteristics of the critical gels and the fully formed hydrogels. Network relaxation exponents (n) were influenced by the concentrations of AA and methylene bis‐acrylamide. The gel stiffness (S) decreased with an increase in the concentration of the monomer and of the concentration of the crosslinker, while network branching decreased (lower fractal dimensions) at the gel point. The conversion at the gel point was found to be iso‐conversion with respect to the intensity of the UV irradiance used in the photocrosslinking reactions (1–20 mW/cm²). Thus, network clusters and the crosslinking reaction mechanism were the same irrespective of radiation intensity, although the rates of the reactions were affected. Having sufficient amounts of reactive species at the time of cure drive the crosslinking reactions beyond the gel point to greater crosslink density and smaller mesh sizes. The effects of auto‐acceleration and free‐volume were observed and shown to have key effects on the gelation mechanisms and the branching topographies of the network, when the concentration of the known polyacrylamide medium were not controlled. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 46691.     

Rheological behavior of noncompatibilized and compatibilized PP/PET blends with SEBS‐g‐MA

The rheological behaviors of noncompatibilized and compatibilized polypropylene/polyethylene terephthalate blends (80/20) in relation with their morphology were studied at two constant levels using maleic anhydride‐modified styrene‐ethylene‐butylene‐styrene polymer. By scanning electron microscopy of cryofractured surfaces, the morphology of the blends was examined after etching. The frequency sweep and step strain experiments were carried out for the blends. The frequency sweep results indicated that increasing the compatibilizer causes behavioral changes of the rheological properties, which could be related to the aggregation of the dispersed particles with rubbery shell. Also, the frequency sweep and step strain experiments in linear region, after cessation of simple steady shear flow with various preshear rates (higher shear stress values than G′_p), were done on compatibilized blend. The results showed that the morphology characteristics, defined by the aggregation of the dispersed particles based on rheological experimental data, were destroyed and replaced by an alignment in the flow direction for present imposed shear rates. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Viscoelastic properties of blends of poly(methyl methacrylate) and poly(styrene‐co‐acrylonitrile) having various acrylonitrile contents

Dynamic viscoelastic properties of blends of poly(methyl methacrylate) (PMMA) and poly(styrene‐co‐acrylonitrile) (SAN) with various AN contents were measured to evaluate the influence of SAN composition, consequently χ parameter, upon the melt rheology. PMMA/SAN blends were miscible and exhibited a terminal flow region characterized by Newtonian flow, when the acrylonitrile (AN) content of SAN ranges from 10 to 27 wt %. Whereas, PMMA/SAN blends were immiscible and exhibited a long time relaxation, when the AN content in SAN is less than several wt % or greater than 30 wt %. Correspondingly, melt rheology of the blends was characterized by the plots of storage modulus G′ against loss modulus G″. Log G′ versus log G″ plots exhibited a straight line of slope 2 for the miscible blends, but did not show a straight line for the immiscible blends because of their long time relaxation mechanism. The plateau modulus, determined as the storage modulus G′ in the plateau zone at the frequency where tan δ is at maximum, varied linearly with the AN content of SAN irrespective of blend miscibility. This result indicates that the additivity rule holds well for the entanglement molecular weights in miscible PMMA/SAN blends. However, the entanglement molecular weights in immiscible blends should have “apparent” values, because the above method to determine the plateau modulus is not applicable for the immiscible blends. Effect of χ parameter on the plateau modulus of the miscible blends could not be found. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Effects of addition of functionalized SEBS on rheological,mechanical, and tribological properties of polyamide 6 nanocomposites

The effects of the addition of styrene‐ethylene/butylene‐styrene copolymer (SEBS) with various functionalized groups on the rheological, mechanical, and tribological properties on polyamide 6 nanocomposite filled with layered silicate (PA6/Clay) were investigated. Four types of SEBS: unmodified SEBS (SEBS), maleic anhydride grafted SEBS (SEBS‐g‐MA), amine group grafted SEBS (SEBS‐g‐NH₂), and carboxyl group grafted SEBS (SEBS‐g‐COOH) were added with PA6/Clay nanocomposite to prepare various polymer blends. These polymer blends were extruded by a twin screw extruder and injection molded. Dynamic viscoelastic properties of these blends in the molten state and their tensile, impact, and tribological properties were evaluated. The viscoelastic properties were found to increase with the addition of SEBS and were highly influenced by the types of functionalized groups contained. Influence of the addition of SEBS on the mechanical properties of these systems differed for each mechanical property. Although the tensile properties decreased with SEBS, Izod impact properties improved with the addition of various functionalized SEBS. These mechanical properties and viscoelastic properties correlated closely with the size of dispersed SEBS particles and interparticle distance. The tribological properties also improved with the addition of SEBS, and the influence of the amount added was higher than the type of SEBS used. POLYM. ENG. SCI., 2010. © 2009 Society of Plastics Engineers     

Evaluation of mechanical properties of polypropylene/polycarbonate/SEBS ternary polymer blends using Taguchi experimental analysis

In this work, ternary polymer blends based on polypropylene (PP)/polycarbonate (PC)/poly(styrene‐b‐(ethylene‐co‐butylene)‐b‐styrene) (SEBS) triblock copolymer and a reactive maleic anhydride grafted SEBS (SEBS‐g‐MAH) at fixed compositions are prepared using twin‐screw extruder at different levels of die temperature (235‐245‐255°C), screw speed (70‐100‐130 rpm), and blending sequence (M1‐M2‐M3). In M₁ procedure, all of the components are dry blended and extruded simultaneously using Brabender twin‐screw extruder, whereas in M₂ procedure, PC, SEBS, and SEBS‐g‐MAH minor phases are first preblended in twin‐screw extruder and after granulating are added to PP continuous phase in twin‐screw extruder. Consequently, in M₃ procedure, PP and SEBS‐g‐MAH are first preblended and then are extruded with other components. The influence of these parameters as processing conditions on mechanical properties of PP/PC/SEBS ternary blends is investigated using L9 Taguchi experimental design. The responding variables are impact strength and tensile properties (Young's modulus and yield stress), which are influenced by the morphology of ternary blend, and the results are used to perform the analysis of mean effect as well. It is shown that the resulted morphology, tensile properties, and impact strength are influenced by extrusion variables. Additionally, the optimum processing conditions of ternary PP/PC/SEBS blends were achieved via Taguchi analysis. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Melt linear viscoelastic rheological analysis to assess the microstructure of polyamide 6–acrylonitrile butadiene styrene terpolymer immiscible blends via the application of fractional Zener and Coran models

In this study, the melt linear viscoelastic rheological properties of polyamide 6 (PA6)–acrylonitrile butadiene styrene terpolymer (ABS) immiscible blends were analyzed with the help of Coran and fractional Zener models (FZMs) to assess the microstructure of the blends. For this purpose, dynamic shear flow experiments and scanning electron microscopy investigations were performed. The nonzero value of the elastic modulus of the spring element (G_e) of the FZM for ABS‐rich blends was explained by the formation of a networklike structure because of the agglomeration of the rubber phases of the ABS matrix, whereas for the PA6‐rich blends with a high content of ABS, the interactions and/or interconnectivity of the ABS dispersed phase led to a nonzero value of G_e. The value of the fitting parameter of the Coran model (f) was near to 0.5 for the 50/50 blend; this was fully in agreement with the formed cocontinuous morphology for this blend composition. On the other hand, the f value for the blends with a matrix–droplet‐type morphology was near to zero for the PA6‐rich blends; this indicated the lower continuity of the ABS dispersed phase as a harder phase compared to the PA6 soft matrix, whereas the f value was near to 1 for ABS‐rich blends. This confirmed the formation of an interconnected networklike structure for this series of blends. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 45423.     

Viscoelastic properties and structure of poly(acrylonitrile‐co‐methacrylic acid) polymer solutions for gel spinning at long aging times

The objective of the research is to obtain a more complete understanding of how aging affects the viscoelastic properties of polymer solutions to be used as starting materials for gel spinning of polymer fibers. Specifically, poly(acrylonitrile‐co‐methacrylic acid) solutions were prepared and characterized using rheological measurements and nuclear magnetic resonance spectroscopy. The results indicate that elastic character increased with increasing polymer concentration and that gelation of these solutions continued up to aging times of several weeks. Additionally, comparing the results from the two characterization methods show that while gelation continues to occur, the viscoelastic properties decrease after a critical time point suggesting that a chemical change occurs in the solutions at long times. However, these changes impact the solution dynamics minimally as the effective network properties were similar at the aging times studied here, but considerations for long‐term storage of polymer solutions for gel spinning are warranted. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 39821.     

Memory functions in polymer modified asphalts

The viscoelastic nonlinear behavior of several base and polymer modified asphalts (PMA) has been studied in step‐strain experiments. The polymers were poly(styrene‐b‐butadiene‐b‐styrene), poly(styrene‐b‐ethylene‐co‐butylene‐b‐styrene), poly(ethylene‐r‐vinylacetate) copolymers, and a linear low density poly(ethylene), which were chosen as representatives of the main categories of asphalt modifiers. Because of the complexity of the morphological structure of these materials, the relaxation modulus has only partial and qualitative similarities with that of melt or high concentrated solutions of entangled polymeric liquids. No time strain separability can be applied, and the relaxation experiments are conveniently described by means of the memory functions. These have been calculated both via a parametric fitting procedure and by interpolation algorithms. Results are presented, and a correlation between the PMA structure and the corresponding memory function is proposed for the investigated materials. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 104: 2330–2340, 2007