Effects of wide‐range γ‐irradiation doses on the structures and properties of 4,4′‐dicyclohexyl methane diisocyanate based poly(carbonate urethane)s

For medical applications, 4,4′‐dicyclohexyl methane diisocyanate (HMDI)‐based poly(carbonate urethane)s were synthesized from HMDI and 1,4‐butanediol as hard segments and poly(carbonate diol) (number‐average molecular weight = 2000 g/mol) as soft segments. The effects of wide‐range γ irradiation on the samples were examined through a series of analytical techniques. Scanning electron microscopy revealed that γ irradiation etched and roughened the surfaces of the irradiated samples. The gel content and crosslinking density measurements confirmed that crosslinking occurred along with degradation at all of the investigated irradiation doses and the degree of both crosslinking and degradation increased with increasing irradiation dose. Fourier transform infrared spectroscopy demonstrated that chain scission in the γ‐irradiated samples occurred at the carbonate and urethane bonds. The decreasing molecular weight and tensile strength indicated that the degradation increased with the γ‐irradiation dose. Differential scanning calorimetry and dynamic mechanical thermal analysis indicated that γ irradiation had no significant effect on the phase‐separation structures. There was a slight reduction in the contact angle. An evaluation of the cytotoxicity demonstrated the nontoxicity of the nonirradiated and irradiated polyurethanes. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 41049.     

Molecular weight studies of the γ‐irradiation degradation of poly(methyl methacrylate) doped with poly(p‐sulfanilamide)

The protection of some poly(methyl methacrylate) (PMMA) samples against γ rays was investigated in the absence and presence of poly(p‐sulfanilamide). Pure PMMA (without additives) and PMMA–poly(p‐sulfanilamide) blend samples were irradiated with γ rays for different exposure doses (5, 15, 25, 35, 50, 75, and 100 kGy). The viscosity‐average molecular weights were determined and thin‐layer chromatography measurements were carried out after each irradiation dose. The maximum protection against γ rays was found when 1% poly(p‐sulfanilamide) was used. The radiation chemical yield for main scission (G_s) was calculated and had lower values in the case of 1% poly(p‐sulfanilamide). The energy absorption per scission was maximum for 1% poly(p‐sulfanilamide), and this confirmed the obtained G_s data. From thin‐layer chromatography studies, it was observed that both the retention factor (R_f) values and polydispersity of the PMMA samples increased with an increasing exposure dose. The effect of γ irradiation on PMMA films doped with 1% poly(p‐sulfanilamide) was investigated with UV spectroscopy after the extraction of the additives. A change in the intensity of the absorption bands with an increasing irradiation dose was recorded. It is suggested that PMMA films doped with this type of polymer can be used as dosimeters. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

Molecular structure and physical properties of E‐beam crosslinked low‐density polyethylene for wire and cable insulation applications

Crosslinking of homemade low‐density polyethylene (LDPE) was performed by electron‐beam (EB) irradiation. The gel content of the EB‐exposed LDPE was determined by the solvent‐extraction method. The degree of crosslinking was also evaluated by a hot set measuring test. The results obtained from both the gel–sol and the hot set methods showed that the degree of crosslinking was dependent on the deposited energy in LDPE samples. Increasing the absorbed dose increased the degree of network formation. The LDPE with higher molecular weight yielded higher efficiency of crosslinking at the same irradiation dose. The effect of irradiation dose on the molecular weight between crosslinks (M_c), glass‐transition temperature, and free volume were calculated. Mechanical test results showed that the tensile strength of the samples increased with increase in the irradiation dose up to 150 kGy and then slightly decreased with further increasing the deposited energy. The elongation at break decreased with increasing the absorbed dose. The results obtained from differential scanning calorimetry exhibited a small reduction in the melting point and the degree of crystallinity of the EB‐exposed LDPE samples compared to those of the untreated samples. The effect of crosslinking on the electrical properties of the irradiated samples was insignificant. The dielectric constant of the treated samples remained nearly constant within the irradiation dose range, although the dissipation factor increased slightly with increasing the absorbed dose. The results obtained from characterizing the EB‐induced crosslinking of homemade polyethylene, including LH0030 and LH0075, showed the higher molecular weight polyethylene (LH0030) as a preferred option for wire and cable insulation. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 86: 1959–1969, 2002     

Degradation of poly(D,L‐lactic acid)‐b‐poly(ethylene glycol)‐b‐poly(D,L‐lactic acid) copolymer by electron beam radiation

This article investigates the effects of electron beam (EB) radiation on poly(D ,L ‐lactic acid)‐b‐poly (ethylene glycol) copolymer (PLA‐b‐PEG‐b‐PLA). The copolymer films were EB irradiated at doses from 0 to 100 kGy. The degradation of these films was studied by measuring the changes in their molecular weight, mechanical and thermal properties. The dominant effect of EB radiation on PLA‐b‐PEG‐b‐PLA is chain‐scission. With increasing irradiation dose, recombination reactions or partial crosslinking may occur in addition to chain scission. The degree of chain scission G_s and crosslinking G_x of sample are calculated to be 0.213 and 0.043, respectively. A linear relationship is also established between the decreases in molecular weight with increasing irradiation dose. Elongation at break of the irradiated sample decreases significantly, whereas its tensile strength decreases slightly. The glass transition temperature (T_g) is basically invariant as a function of irradiation dose. Thermogravimetric analysis shows that its thermal stability decreases with increasing dose. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Thermal analysis of poly(3‐hydroxybutyrate‐co‐3‐hydroxyvalerate) irradiated under vacuum

Poly(3‐hydroxybutyrate‐co‐3‐hydroxyvalerate) (PHBV) was irradiated by ⁶⁰Co γ‐rays (doses of 50, 100 and 200 kGy) under vacuum. The thermal analysis of control and irradiated PHBV, under vacuum was carried out by thermogravimetric analysis (TGA) and differential scanning calorimetry (DSC). The tensile properties of control and irradiated PHBV were examined by using an Instron tensile testing machine. In the thermal degradation of control and irradiated PHBV, a one‐step weight loss was observed. The derivative thermogravimetric curves of control and irradiated PHBV confirmed only one weight‐loss step change. The onset degradation temperature (T_o) and the temperature of maximum weight‐loss rate (T_p) of control and irradiated PHBV were in line with the heating rate (°C min^?1). T_o and T_P of PHBV decreased with increasing radiation dose at the same heating rate. The DSC results showed that ⁶⁰Co γ‐radiation significantly affected the thermal properties of PHBV. With increasing radiation dose, the melting temperature (T_m) of PHBV shifted to a lower value, due to the decrease in crystal size. The tensile strength and fracture strain of the irradiated PHBV decreased, hence indicating an increased brittleness. Copyright © 2004 Society of Chemical Industry     

Dielectric properties of γ‐irradiated POE highly filled with aluminum hydroxide

The influence of γ irradiation on the dielectric and physicochemical properties of polyethylene‐octene elastomer (POE) containing 120 phr aluminum hydroxide (Al(OH)₃) as fillers has been investigated. The dielectric properties of the γ‐irradiated POE highly filled with Al(OH)₃ have been measured over a wide range of frequencies (70 kHz–3 MHz). It was found that γ irradiation strongly influences the dielectric properties of the POE composite in the dose range 0–250 kGy. POLYM. ENG. SCI. 46:1721–1727, 2006. © 2006 Society of Plastics Engineers     

13C‐NMR, 1H‐NMR,and FT‐Raman study of radiation‐induced modifications in radiation dosimetry polymer gels

¹H‐ and ¹³C‐NMR spectroscopy and FT‐Raman spectroscopy are used to investigate the properties of a polymer gel dosimeter post‐irradiation. The polymer gel (PAG) is composed of acrylamide, N,N′‐methylene‐bisacrylamide, gelatin, and water. The formation of a polyacrylamide network within the gelatin matrix follows a dose dependence nonlinearly correlated to the disappearance of the double bonds from the dissolved monomers within the absorbed dose range of 0–50 Gy. The signal from the gelatin remains constant with irradiation. We show that the NMR spin–spin relaxation times (T₂) of PAGs irradiated to up to 50 Gy measured in a NMR spectrometer and a clinical magnetic resonance imaging scanner can be modeled using the spectroscopic intensity of the growing polymer network. More specifically, we show that the nonlinear T₂ dependence against dose can be understood in terms of the fraction of protons in three different proton pools. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 79: 1572–1581, 2001     

The effect of 60Co γ‐rays on the crystal structure,melting and crystallization behavior of poly(butylene succinate)

The results obtained for poly(butylene succinate) (PBS) after ⁶⁰Co γ‐ray irradiation, studied by wide‐angle X‐ray diffraction (WAXD), differential scanning calorimeter (DSC) and polarizing optical microscopy (POM), revealed that the degree of crystallinity, melting temperature and enthalpy decreased with increasing irradiation dose, but that the crystal structure of PBS did not vary when compared to non‐irradiated PBS. By using Scherrer equation, small changes occurred in the crystal sizes of L₀₂₀, L₁₁₀ and L₁₁₁. The spherulitic morphology of PBS was strongly dependent on irradiation dose and changed significantly at higher irradiation dosages. The crystallization kinetics of PBS indicated that the Avrami exponent (n) for irradiated PBS was reduced to 2.3, when compared to non‐irradiated PBS (3.3). Copyright © 2004 Society of Chemical Industry     

Effect of γ‐radiation on the thermal and mechanical properties of a commercial poly(butylene adipate‐co‐terephthalate)

BACKGROUND: Poly(butylene adipate‐co‐terephthalate) (PBAT) has attracted wide interest as a biodegradable polymer. However, its use is restricted in certain applications due to its low melting point. RESULTS: PBAT was treated using γ‐radiation. The radiation features were analyzed using Soxhlet extraction, and the ratio of chain scission and crosslinking and gelation dose were determined using the classical Charlesby–Pinner equation. The results showed that PBAT is a radiation‐crosslinkable polymer. The degree of crosslinking increased with increasing radiation dose; the relation between sol fraction and dose followed the Charlesby–Pinner equation. Differential scanning calorimetry analyses showed that the melting temperature (T_m) and the heat of fusion (ΔH_m) of PBAT exhibited almost no change in the first scan. The second scan, however, showed a decrease in T_m and ΔH_m. The glass transition temperature of irradiated PBAT increased with increasing radiation dose. The weight loss of control and irradiated PBAT resulting from thermal degradation was a one‐step process. Moreover, the tensile strength and elongation at break decreased with an increase in radiation dose. However, the Young's modulus and stress at yield were not greatly affected by γ‐radiation. CONCLUSION: PBAT can be crosslinked using γ‐radiation. The crosslinking efficiency is relatively low. The thermal and mechanical properties of PBAT are affected by γ‐radiation. Copyright © 2009 Society of Chemical Industry     

Enhancement of the mechanical properties and interfacial interaction of a novel chitin‐fiber‐reinforced poly(ϵ‐caprolactone) composite by irradiation treatment

The effects of the fiber reinforcement of a novel bioabsorbable chitin‐fiber‐reinforced poly(?‐caprolactone) (PCL) composite were improved by irradiation treatment. The tensile strength and tensile modulus of the treated specimens were enhanced with respect to those of the untreated specimens. An increase in the fiber content (C_f) resulted in an increase in this enhancement tendency until C_f was 45%. A further increase in C_f increased the tensile modulus but decreased the strength. The flexural strength and flexural modulus were increased for the irradiation‐treated specimens in the same way as the tensile test. The microstructure of the tensile fracture showed an improvement in interfacial bonding for the irradiated specimens. The glass‐transition temperature (T_g) of the composite increased with an increase in C_f for the irradiation‐treated specimens, but there was no change in T_g for the untreated specimens with various values of C_f. This indicated that, for the composites with irradiation treatment, the fiber intensively affected the molecular segmental motion of PCL and thereby enhanced the interfacial interaction between the matrices and fibers. The same slope of the storage modulus (G′) versus the loss modulus (G″) for the irradiated specimens suggested an increase in the compatibility of the composite in comparison with the decrease in the slope with increasing C_f for the untreated specimens. All this demonstrated that there was some interfacial reaction between the fiber and matrix that resulted in the presence of an interfacial phase and improved the mechanical properties of the materials. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 84: 486–492, 2002; DOI 10.1002/app.10149     

Molecular weight development in emulsion copolymerization of n‐butyl acrylate and styrene

The seeded emulsion copolymerization of n‐butyl acrylate and styrene in a weight ratio of 50/50 was investigated. The effect of the type of process (batch vs. semicontinuous) and the amounts of initiator and emulsifier charged into the reactor on the time evolution of the fractional conversion, number of polymer particles, and weight‐average molecular weight (M_w) was analyzed. It was found that the M_w depends to a slight extent on the type of process and the emulsifier concentration and to a larger extent on the initiator concentration. The molecular weight distributions (MWDs) and the gel content of the final latexes were also analyzed. In the absence of chain transfer agents (CTAs), the fraction of gel was higher in the semicontinuous processes. It was also found that the gel content increased with increasing initiator concentration in the recipe. The addition of 1 wt % CTA avoided gel formation and led to an important reduction of the M_w. Nevertheless, the MWDs presented a shoulder or even a second peak at high molecular weights that was due to reactions of chain transfer to the polymer. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 87: 1918–1926, 2003     

Properties of biodegradable hydrogels prepared by γ irradiation of microbial poly(ϵ-lysine) aqueous solutions

Poly(?-lysine) (PL) hydrogels have been prepared by means of γ irradiation of PL produced by Streptomyces albulus in aqueous solutions. When the dosage of γ irradiation was 70 kGy or more and the concentration of PL in water was 1–7 wt %, transparent hydrogels (opaque hydrogels for 1–3 wt % PL concentration) could be produced. In the case of 70 kGy of γ irradiation and 5 wt % PL concentration, the specific water content (wt of absorbed water/wt of dry hydrogel) of the PL hydrogel was approximately 160. Specific water contents of PL hydrogels decreased markedly with an increase in the dosage of γ irradiation. The specific water contents were increased with an increase in PL concentration in the irradiated solution. This result indicates the presence of a radical scavenger in the PL solution. Swelling equilibria of PL hydrogels were measured in water or in aqueous solutions of various pHs or concentrations of NaCl, Na₂SO₄, and CaCl₂. Under acid conditions, the PL hydrogel swelled due to the ionic repulsion of the protonated amino groups in the PL molecules. The degree of deswelling in electrolyte solution was smaller than that of other ionic hydrogels [poly(γ-glutamic acid), poly(acrylic acid) etc.]. In addition, the enzymatic degradations of PL hydrogel were studied at 40°C and pH 7.0 in an aqueous solution of the neutral protease [Protease A (Amano)] produced from Aspergillus oryzae. The rate of enzymatic degradation of the respective PL hydrogels was much faster than the rate of simple hydrolytic degradation. The rate of enzymatic degradation decreased with the increase in γ-irradiation dose during preparation of the PL hydrogel. © 1995 John Wiley & Sons, Inc.     

Thermal,structural, and optical properties of γ‐irradiated poly(vinyl alcohol)/poly(ethylene glycol) thin film

Poly(vinyl alcohol)/poly(ethylene glycol) (PVA/PEG) copolymer was prepared using casting technique. The obtained PVA/PEG thin films have been irradiated with gamma rays with doses ranging from 1.5 to 20 Gy. The resultant effect of gamma irradiation on the thermal properties of PVA/PEG has been investigated using thermogravimetric analysis (TGA) and differential thermal analysis (DTA). The onset temperature of decomposition T_o and activation energy of thermal decomposition E_a were calculated, results indicating that the PVA/PEG thin film decomposes in one main weight loss stage. Also, the gamma irradiation in dose range 4–12 Gy led to a more compact structure of PVA/PEG copolymer, which resulted in an improvement in its thermal stability with an increase in the activation energy of thermal decomposition. The variation of transition temperatures with gamma dose has been determined using DTA. The PVA/PEG thermograms were characterized by the appearance of an endothermic peak due to melting of crystalline phase. In addition, structural property studies using X‐ray diffraction and infrared spectroscopy were performed on both nonirradiated and irradiated samples. Furthermore, the transmission of the PVA/PEG samples and any color changes were studied. The color intensity (E was greatly increased with increasing the gamma dose and was accompanied by a significant increase in the blue and green color components. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Effects of various ester groups in γ-radiation degradation of syndiotactic poly(methacrylate)s

The γ irradiation of poly(methacrylate)s with various ester groups at room temperature was investigated by gel permeation chromatography and NMR techniques. The G values for scission and crosslinking for each of the polymers were estimated from the changes in the molecular weights and molecular weight distributions. The new structures formed during γ irradiation were examined by ¹H-NMR spectroscopy. All of the investigated poly(alkanemethacrylate)s were found to produce the alkane formates during γ irradiation, and for poly(2-methyl heptyl methacrylate) G(S) was less than 4G(X), indicating gel formation in this polymer. In the investigation of poly(benzyl methacrylate), no formate ester was found, but some small molecule compounds formed from the benzyl radical were detected. The benzyl group was also found to stabilize the polymer against radiation damage. © 1996 John Wiley & Sons, Inc.     

Synthesis and swelling characteristics of poly(4‐vinylpyridine) gels crosslinked by irradiation

The effect of irradiation under vacuum on thermal properties and swelling behavior on poly(4‐vinylpyridine) (P4VP) was investigated. The gel percentage in the irradiated P4VP films was determined by Soxhlet extraction. UV spectroscopy was also used to determine sol percentage, which decreased as the radiation dose increased. The changes in thermal properties, such as glass‐transition temperature (T_g), were followed by differential scanning calorimetry before and after Soxhlet extraction. The gels prepared after irradiation were characterized with respect to their swelling properties and network structures. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 81: 2609–2614, 2001     

Influence of radiation structures on positive‐temperature‐coefficient and negative‐temperature‐coefficient effects of irradiated low‐density polyethylene/carbon black composites

The electrical‐resistivity/temperature behaviors of low‐density polyethylene (LDPE)/carbon black (CB) composites irradiated with ⁶⁰Co γ rays were studied. The experimental results showed that the irradiated composites could be separated into insoluble crosslinking networks with CB (gel) and soluble components (sol) by solvent‐extraction techniques. When the sol of an irradiated LDPE/CB composite was extracted, the electrical conductivity of the system increased. The positive‐temperature‐coefficient (PTC) and negative‐temperature‐coefficient (NTC) intensities of the gels of the irradiated composites became extremely small and independent of the radiation dose. The sols and gels of the irradiated LDPE/CB composites, which had different thermal behaviors, played important roles in the appearances of the PTC and NTC effects. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 95: 700–704, 2005     

Influence of two‐stage drawing conditions on ultradrawing behavior of gel films of ultrahigh‐molecular‐weight polyethylene and low‐molecular‐weight polyethylene blends

The influence of two‐stage drawing conditions on the ultradrawing behavior of the gel films of ultrahigh‐molecular‐weight polyethylene/low‐molecular‐weight polyethylene blends is reported in this article. The critical draw ratios (λ_c) of the gel films prepared near their critical concentrations were found to depend significantly on the draw ratio attained in the first drawing stage (D_1r) and on the temperature utilized in the second drawing stage (T_sec). After drawing the gel films to a fixed draw ratio in the first drawing stage, each two‐stage drawn gel film was made to exhibit a maximum λ_c (λ_cmax) by drawing the drawn gel film at its corresponding optimum T_sec. In addition, the optimum T_sec was found to increase significantly with the D_1r value of the drawn gel films. It is worth noting, on the other hand, that the λ_cmax of two‐stage drawn gel films increased consistently with an increasing D_1r until its value reached an optimum value of 160. These results clearly suggest that, as T_sec and D_1r are increased to their optimum values, the λ_cmax of the two‐stage drawn gel films can be improved further so as to be higher than those of the corresponding one‐stage drawn gel films. These interesting phenomena were investigated in terms of reduced viscosities of the solutions and by an analysis of the thermal, birefringence, and tensile properties of the drawn gel films. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 79: 1890–1901, 2001     

Improving properties of superabsorbent composite induced by using alkaline protease hydrolyzed‐sericin (APh‐sericin)

A series of superabsorbent polymer composites based on sericin hydrolyzed with alkaline protease (AP) were prepared by grafting with acrylic acid (AA) and acrylamide (AM). The properties of the superabsorbent polymers (SAP) by using hydrolyzed sericin with different amount of alkaline protease (nAPh‐sericin) were compared. It was found that the polymer prepared from 5APh‐sericin (the mass ratio of AP to sericin was 5.0 mg g⁻¹) showed the highest graft percentage and water absorbency, this phenomenon may be attributed to the change of molecular weight of resulting sericin molecules. The molecular structure of the grafted polymers was proved by thermal gravimetric analysis (TGA) and Fourier transform infrared spectroscopy (FTIR) measurements. Comparing with PAA‐AM (poly AA‐co‐AM) and 0APh‐sericin/PAA‐AM polymer, 5APh‐sericin/PAA‐AM polymer had the most excellent water retention capacity and enzyme degradability. The morphological features of the polymers with different drying methods were evidenced by SEM images. The water absorbencies of 5APh‐sericin/PAA‐AM polymer prepared with freeze‐drying were 896 g g⁻¹ in deionized water, 424 g g⁻¹ in tap water, and 83 g g⁻¹ in 0.9 wt% aqueous NaCl solution. POLYM. COMPOS., 35:509–515, 2014. © 2013 Society of Plastics Engineers     

γ Irradiation effects on optical,thermal, and mechanical properties of polysulfone/MWCNT nanocomposites in argon atmosphere

Polymer‐based composites find use in many nuclear and space application for their ease of fabrication, tailor made properties and light weight. Certain polymers like PTFE, unfilled polyesters and polyamides are prone to degradation in presence of high energy radiation while polymers like epoxies, polyimides, and poly‐ether ether ketone have good stability to ionizing radiation. Incorporation of fillers like carbon nanotubes (CNTs) is likely to improve the radiation resistance of the polymers. In this work, polysulfone (PSU)‐based nanocomposites were fabricated using multiwalled carbon nanotube (MWCNT) by solution mixing process. The morphology of the PSU/ MWCNT nanocomposites films were studied using Field Emission Scanning Electron Microscopy (FESEM). The prepared films were subjected to γ radiation in an argon environment (to avoid the effect of air/oxygen). Different techniques were used to understand the radiation‐induced changes. Gel Permeation Chromatography (GPC) traces of neat PSU before and after exposure to radiation shows a decrease in molecular weight. Infrared spectroscopy shows changes in chemical structure. Differential Scanning Calorimetry (DSC) thermograms reveal dose‐related changes. For neat PSU, a decrease in T_g was observed with increase in dose. For PSU/ MWCNT nanocomposites, the increase in MWCNT content and dose (up to 1.5 MGy) increased the T_g. Thermo Gravimetric Analysis (TGA) showed a marginal decrease in thermal stability for pristine PSU as well as PSU/MWCNT nanocomposites with irradiation. Tensile strength increased with increasing MWCNT content but decreased with dose. Elongation at break decreased with MWCNT content as well as radiation dose. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42017.     

Electrical and thermal properties of γ‐irradiated nitrile rubber/rice husk ash composites

The effects of both the rice husk ash (RHA) loading and fumed silica (FS) loading on the structure, thermal stability, and electrical properties of acrylonitrile–butadiene rubber (NBR) composites were studied. The filler loading were chosen to be 5 and 20 phr for RHA and 5 and 30 phr for silica. Also, the effect of the γ‐irradiation dose (25 kGy) on these parameters was investigated. The structure and thermal stability were studied with X‐ray diffraction and thermogravimetric analysis techniques. Furthermore, some electrical parameters, such as the direct‐current electrical conductivity (σ_dc), activation energy (E_a), dielectric constant (?′), and dielectric loss (?″), were determined. The incorporation of both RHA and FS resulted in improved thermal stability after γ irradiation at 25 kGy. The loading of FS on NBR was shown to decrease σ_dc, ?′, and ?″ and increase E_a. On the other hand, the loading of RHA showed the opposite trend. Finally, γ irradiation of NBR composites filled with both fillers decreased the values of σ_dc, ?′, and ?″ for all the samples, which followed the trend for the unirradiated composites. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2010