Blends of SBS triblock copolymer with poly(2,6‐dimethyl‐1,4‐phenylene oxide)/polystyrene mixture

Blends of styrene–butadiene–styrene (SBS) or styrene–ethylene/1‐butene–styrene (SEBS) triblock copolymers with a commercial mixture of polystyrene (PS) and poly(2,6‐dimethyl‐1,4‐phenylene oxide) (PPO) were prepared in the melt at different temperatures according to the chemical kind of the copolymer. Although solution‐cast SBS/PPO and SBS/PS blends were already known in the literature, a general and systematic study of the miscibility of the PS/PPO blend with a styrene‐based triblock copolymer in the melt was still missing. The thermal and mechanical behavior of SBS/(PPO/PS) blends was investigated by means of DSC and dynamic thermomechanical analysis (DMTA). The results were then compared to analogous SEBS/(PPO/PS) blends, for which the presence of a saturated olefinic block allowed processing at higher temperatures (220°C instead of 180°C). All the blends were further characterized by SEM and TGA to tentatively relate the observed properties with the blends' morphology and degradation temperature. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 88: 2698–2705, 2003     

Investigation on the miscibility of the blends of poly(methyl methacrylate) and poly(styrene‐co‐acrylonitrile)

The miscibility was investigated in blends of poly(methyl methacrylate) (PMMA) and styrene‐acrylonitrile (SAN) copolymers with different acrylonitrile (AN) contents. The 50/50 wt % blends of PMMA with the SAN copolymers containing 5, 35, and 50 wt % of AN were immiscible, while the blend with copolymer containing 25 wt % of AN was miscible. The morphologies of PMMA/SAN blends were characterized by virtue of scanning electron microscopy and transmission electron microscopy. It was found that the miscibility of PMMA/SAN blends were in consistence with the morphologies observed. Moreover, the different morphologies in blends of PMMA and SAN were also observed. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Optical transparency,thermal resistance,intermolecular interaction,and mechanical properties of poly(styrene‐butadiene‐styrene) copolymer‐based thermoplastic elastomers

The optical transparency, thermal resistance, intermolecular interaction, and mechanical properties of poly(styrene‐block‐butadiene‐block‐styrene) (SBS), which were modified by blending with crystalline polypropylene (PP) or amorphous polystyrene (PS), were analyzed. The dynamic mechanical test indicated that the PP exhibited an intermolecular interaction with SBS and PS was compatible with SBS. The optical properties indicated that the direction of the light was changed due to the difference between the refractive indices of SBS and the added modifiers. Additionally, refraction and reflection occurred at the interface, reducing the transparency of SBS. The thermal resistance of SBS clearly improved upon modification by the addition of crystalline PP polymer. The thermal treatment increased the tensile strength and the elongation at breakage of modified SBS by reducing the internal stress, which was generated during the blending process. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Fabrication of Damping Material over Broad Temperature Range: Blending Amorphous Styrene‐Butadiene‐Styrene Triblock Copolymer with Semi‐Crystalline Syndiotactic 1,2‐Polybutadiene

Broad‐temperature‐range (?85.4 to 96.2 °C) damping material was fabricated by blending amorphous styrene‐butadiene‐styrene triblock copolymer (SBS) with semicrystalline syndiotactic 1,2‐polybutadiene (s‐PB). According to dynamic mechanical thermal analysis (DMTA) analysis, SBS/s‐PB blends exhibited three consecutive damping peaks at ?85.4, 2.7, and 96.2 °C. The peaks at ?85.4 and 96.2 °C were associated with the glass transition of polybutadiene and polystyrene in SBS, and peak at 2.7 °C belonged to the glass transition of s‐PB. The analysis of rheological behavior and thermal properties showed that the mobility and thermal stability of SBS/s‐PB blends improved with the introduction of semi‐crystalline s‐PB. Moreover, regarding the results of DMTA, Fourier transform infrared spectroscopy (FTIR) and Scanning electron microscopy (SEM) measurements, SBS and s‐PB were compatible in the macroscopic scale while they were immiscible in thermodynamic scale. Wide‐angle X‐ray diffraction (WAXD) results present the crystal structure of blends were unchanged. Besides, with the introduction of s‐PB in blends, 100% tensile modulus increased from 3.2 to 5.8 MPa and tear strength increased from 49.2 to 84.2 kN/m. The Kerner–Uemura–Takayanagi model was employed to compare with experimental data. Thus, broad‐temperature‐range damping material was fabricated by blending SBS with s‐PB and the material combined with good processability, thermal stability, and mechanical properties. J. VINYL ADDIT. TECHNOL., 26:336–347, 2020. © 2019 Society of Plastics Engineers     

Miscibility and crystallization of biodegradable poly(3‐hydroxybutyrate‐co‐3‐hydroxyhexanoate)/poly(vinyl phenol) blends

Miscibility and crystallization of biodegradable poly (3‐hydroxybutyrate‐co‐3‐hydroxyhexanoate) (PHBHHx)/poly(vinyl phenol) (PVPh) blends were investigated in this work. PHBHHx is miscible with PVPh over the whole composition range as evidenced by the single composition dependent glass transition temperature and the depression of equilibrium melting point of PHBHHx in the blends. The overall crystallization rates decrease with increasing crystallization temperature for both neat PHBHHx and its blends with PVPh; moreover, the overall crystallization rates are slower in the PHBHHx/PVPh blends than in neat PHBHHx at the same crystallization temperature. Blending with PVPh may change the crystallization mechanism of PHBHHx in the blends compared with that of neat PHBHHx. Both neat PHBHHx and the PHBHHx/PVPh blends exhibit a crystallization regime II to III transition. The crystal structure of PHBHHx is not modified in the PHBHHx/PVPh blends; however, the values of crystal layer thickness, amorphous layer thickness, and long period all become larger with increasing PVPh content in the blends. POLYM. ENG. SCI., 2012. © 2011 Society of Plastics Engineers     

Influence of the tert‐dodecyl mercaptan content in poly(acrylonitrile‐butadiene‐styrene) on properties of chlorinated polyvinyl chloride/poly(acrylonitrile‐butadiene‐styrene) blends

A series of poly(acrylonitrile‐butadiene‐styrene) (ABS) grafting modifiers were synthesized by emulsion grafting poly(acrylonitrile‐styrene) (SAN) copolymer onto polybutadiene (PB) latex rubber particles. The chain transfer reagent tert‐dodecyl mercaptan (TDDM) was used to regulate the grafting degree of ABS and the molecular weight of SAN copolymers. By blending these ABS modifiers with Chlorinated polyvinyl chloride (CPVC) resin, a series of CPVC/ABS blends were obtained. The morphology, compatibility, and the mechanical properties of CPVC/ABS blends were investigated. The scanning electron microscope (SEM) studies showed that the ABS domain all uniformly dispersed in CPVC matrix. Dynamic mechanical analyses (DMA) results showed that the compatibility between CPVC and SAN became enhanced with the TDDM content. From the mechanical properties study of the CPVC/ABS blends, it was revealed that the impact strength first increases and then decreases with the TDDM content, which means that the compatibility between CPVC and the SAN was not the only requirement for maximizing toughness. The decreasing of tensile strength and the elongations might attribute to the lower entanglement between chains of CPVC and SAN. POLYM. ENG. SCI., 2011. © 2011 Society of Plastics Engineers     

Lamellar morphology of poly(trimethylene terephthalate)/poly(ether imide) blends studied via small‐angle X‐ray scattering

The lamellar morphology of a melt‐miscible blend consisting of poly(trimethylene terephthalate) (PTT) and poly(ether imide) (PEI) prepared by solution precipitation has been investigated by means of optical polarized microscopy (POM) and small angle X‐ray scattering (SAXS). From the observation under POM, it was suggested that PEI was predominantly segregated into the interlamellar and/or interfibrillar regions upon PTT crystallization since the PTT spherulitic morphologies of blends were volume‐filling. From results of SAXS data analysis, a larger amorphous layer thickness was identified in the blends, showing that some PEI was incorporated inside the interlamellar regions after crystallization. Despite the swelling of the amorphous layer, the amorphous layer thickness was relatively independent of the blend composition. It was concluded that amorphous PEI was located in the interlamellar regions of PTT as the weight fraction of PEI (w_PEI) [≤] 0.1, while amorphous PEI was predominantly segregated into the interfibrillar regions of PTT as w_PEI > 0.1, and the extent of interfibrillar segregation increased with increasing w_PEI. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci, 2006     

Crystallization behavior of PEO in blends of poly(ethylene oxide)/poly(2‐vinyl pyridine)‐b‐(ethylene oxide) block copolymer

The crystallization behavior of two molecular weight poly(ethylene oxide)s (PEO) and their blends with the block copolymer poly(2‐vinyl pyridine)‐b‐poly(ethylene oxide) (P2VP‐b‐PEO) was investigated by polarized optical microscopy, thermogravimetric analysis, differential scanning calorimetry, and atomic force microscopy (AFM). A sharp decreasing of the spherulite growth rate was observed with the increasing of the copolymer content in the blend. The addition of P2VP‐b‐PEO to PEO increases the degradation temperature becoming the thermal stability of the blend very similar to that of the block copolymer P2VP‐b‐PEO. Glass transition temperatures, T_g, for PEO/P2VP‐b‐PEO blends were intermediate between those of the pure components and the value increased as the content of PEO homopolymer decreased in the blend. AFM images showed spherulites with lamellar crystal morphology for the homopolymer PEO. Lamellar crystal morphology with sheaf‐like lamellar arrangement was observed for 80 wt% PEO(200M) and a lamellar crystal morphology with grain aggregation was observed for 50 and 20 wt% blends. The isothermal crystallization kinetics of PEO was progressively retarded as the copolymer content in the blend increased, since the copolymer hinders the molecular mobility in the miscible amorphous phase. POLYM. ENG. SCI., 2012. © 2011 Society of Plastics Engineers     

Enzymatic degradation of blends of poly(ε‐caprolactone) and poly(styrene‐co‐acrylonitrile) by Pseudomonas lipase

In polymer blends, the composition and microcrystalline structure of the blend near surfaces can be markedly different from the bulk properties. In this study, the enzymatic degradation of poly(ε‐caprolactone) (PCL) and its blends with poly(styrene‐co‐acrylonitrile) (SAN) was conducted in a phosphate buffer solution containing Pseudomonas lipase, and the degradation behavior was correlated with the surface properties and crystalline microstructure of the blends. The enzymatic degradation preferentially took place at the amorphous part of PCL film. The melt‐quenched PCL film with low crystallinity and small lamellar thickness showed a higher degradation rate compared with isothermally crystallized (at 36, 40, and 44°C) PCL films. Also, there was a vast difference in the enzymatic degradation behavior of pure PCL and PCL/SAN blends. The pure PCL showed 100% weight loss in a very short time (i.e., 72 h), whereas the PCL/SAN blend containing just 1% SAN showed ～50% weight loss and the degradation ceased, and the blend containing 40% SAN showed almost no weight loss. These results suggest that as degradation proceeds, the nondegradable SAN content increases at the surface of PCL/SAN films and prevents the lipase from attacking the biodegradable PCL chains. This phenomenon was observed even for a very high PCL content in the blend samples. In the blend with low PCL content, the inaccessibility of the amorphous interphase with high SAN content prevented the attack of lipase on the lamellae of PCL. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 83: 868–879, 2002     

Miscibility and thermal and mechanical properties of melt‐mixed poly(lactic acid)/poly(trimethylene terephthalate)/(methyl methacrylate)‐butadiene‐styrene copolymer blends

This study examined the miscibility and mechanical properties of melt‐mixed poly(lactic acid) (PLA), poly (trimethylene terephthalate) (PTT), and PLA/PTT blend with 5–10 phr of methyl methacrylate‐butadiene‐styrene copolymer (MBS). The isothermal crystallization kinetics of the PTT blends were analyzed by using the Avrami equation. The Differential Scanning Calorimetry (DSC) and scanning electron microscope results indicated that the miscibility of the PLA/PTT blends was improved by adding 5–10 phr of MBS. Although PLA, with the addition of 10 phr of MBS, had lower tensile strength at yield and higher breaking elongation and impact strength than pure PLA, no improvement in these mechanical properties could be observed in PLA/PTT blends. This result is explained by assuming that the crystallization of PTT at the interface favors the disentanglement of MBS from the PTT domain. J. VINYL ADDIT. TECHNOL., 2011. © 2011 Society of Plastics Engineers     

Morphology and mechanical properties of polypropylene and poly(ethylene‐co‐methyl acrylate) blends

The morphology and mechanical properties of isotactic polypropylene (iPP) and poly(ethylene‐co‐methyl acrylate) (EMA) blends were investigated. Various EMA copolymers with different methyl acrylate (MA) comonomer content were used. iPP and EMA formed immiscible blends over the composition range studied. The crystallization and melting reflected that of the individual components and the crystallinity was not greatly affected. The size of the iPP crystals was larger in the blends than those of pure iPP, indicating that EMA may have reduced the nucleation density of the iPP; however, the growth rate of the iPP crystals was found to remain constant. The tensile elongation at break was greatly increased by the presence of EMA, although the modulus remained approximately constant until the EMA composition was greater than 20%. EMA with a 9.0% MA content provided the optimum effect on the mechanical properties of the blends. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 175–185, 2003     

Improvement of microstructures and properties of poly(lactic acid)/poly(ε‐caprolactone) blends compatibilized with polyoxymethylene

Incompatibility of poly(lactic acid)/poly(?‐caprolactone) (PLA/PCL) (80:20) and (70:30) blends were modified by incorporation of a small amount of polyoxymethylene (POM) (≤3 phr). Impact of POM on microstructures and tensile property of the blends were investigated. It is found that the introduction of POM into the PLA/PCL blends significantly improves their tensile property. With increasing POM loading from zero to 3 phr, elongation at break increases from 93.2% for the PLA/PCL (70:30) sample to 334.8% for the PLA/PCL/POM (70:30:3) sample. A size reduction in PCL domains and reinforcement in interfacial adhesion with increasing POM loading are confirmed by SEM observations. The compatibilization effect of POM on PLA/PCL blends can be attributed to hydrogen bonding between methylene groups of POM and carbonyl groups of PLA and PCL. In addition, nonisothermal and isothermal crystallization behaviors of PLA/PCL/POM (70:30:x) samples were investigated by using differential scanning calorimetry and wide angle X‐ray diffraction measurements. The results indicate that the crystallization dynamic of PLA matrix increases with POM loadings. It can be attributed to the fact that POM crystals have a nucleating effect on PLA. While crystallization temperature is 100 °C, crystallization half‐time can reduce from 9.4 to 2.0 min with increasing POM loading from zero to 3 phr. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 46536.     

Influences of dicumyl peroxide on morphology and mechanical properties of polypropylene/poly(styrene‐b‐butadiene‐b‐styrene) blends via vane‐extruder

Polypropylene (PP) and poly(styrene‐b‐butadiene‐b‐styrene) block copolymer (SBS) were melt‐blended in the presence of initiator system. Dicumyl peroxide (DCP)/Triallyl isocyanurate (TAIC) via self‐deigned VE, aiming at in situ reactive compatibilization of toughed PP/SBS blend. The reactivity, morphology and mechanical properties of PP/SBS/DCP/TAIC blends were studied. Online torque detection was conducted to monitor changes in viscosities of reactive compatibilized blends, which could give proof of the interfacial grafted reaction induced by DCP/TAIC system. The effect of reactive compatibilization on the dispersed particles sizes and interfacial adhesion was studied by scanning electron microscopy. Analysis on mechanical performance revealed the impact strength improved after treated by initiator system, moreover, the impact‐fractured surface observation showed, the failure mode changed from debonding mechanism of neat 50PP/50SBS blend to plastic deformation mechanism of blend containing 3.0 phr initiator system. With improved interfacial adhesion, compatibilized blends not only were toughened but also exhibited enhanced tensile strength and thermal stability. Dynamic mechanical analysis showed a reduction of between PP phase and the PB segments in SBS phase, indicating reactive compatibilization of the blend was achieved. In the final part, a brief discussion was given about the dominant effects from chain scission of PP matrix to intergrafting reactions of PP and SBS, under different content of DCP/TAIC initiator system. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41543.     

Morphology and rheological behavior of maltene–polymer blends. I. Effect of partial hydrogenation of poly(styrene‐block‐butadiene‐block‐styrene‐block)‐type copolymers

Because of the importance of the maltene–polymer interaction for the better performance of polymer‐modified asphalts, this article reports the effects of the molecular characteristics of two commercial poly(styrene‐block‐butadiene‐block‐styrene‐block) (SBS) polymers and their partially hydrogenated derivatives [poly{styrene‐block[(butadiene)_1?x–(ethylene‐co‐butylene)_x]‐block‐styrene‐block} (SBEBS)] on the morphology and rheological behavior of maltene–polymer blends (MPBs) with polymer concentrations of 3 and 10% (w/w). Each SBEBS and its parent SBS had the same molecular weight and polystyrene block size, but they differed from each other in the composition of the elastomeric block, which exhibited the semicrystalline characteristics of SBEBS. Maltenes were obtained from Ac‐20 asphalt (Pemex, Salamanca, Mexico), and the blends were prepared by a hot‐mixing procedure. Fluorescence microscopy images indicated that all the blends were heterogeneous, with polymer‐rich and maltene‐rich phases. The rheological behavior of the blends was determined from oscillatory shear flow data. An analysis of the storage modulus, loss modulus, complex modulus, and phase angle as a function of the oscillatory frequency at various temperatures allowed us to conclude that the maltenes behaved as pseudohomogeneous viscoelastic materials that could dissipate stress without presenting structural changes; moreover, all the MPBs were more viscoelastic than the neat maltenes, and this depended on both the characteristics and amount of the polymer. The MPBs prepared with SBEBS were more viscoelastic and possessed higher elasticity than those prepared with SBS. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Transparent,fluorescent, and mechanical enhanced elastomeric composites formed with poly (styrene‐butadiene‐styrene) and SiO2‐hybridized CdTe quantum dots

Transparent poly(styrene‐butadiene‐styrene) (SBS)‐quantum dots (QDs) composites (SBS/CdTe QDs) that simultaneously possess strong photoluminescence (PL) and enhanced mechanical properties are presented for the first time based on the facile blending of SiO₂‐hybridized CdTe QDs with SBS. UV–vis spectrum and fluorescence measurement show that SBS/CdTe QDs composites exhibit good optical properties. The results of transmission electron microscopy show good dispersion of CdTe QDs in the SBS matrix. The results of dynamic mechanical thermal analysis indicate that the micro‐phase separated structure of the SBS is exist in the composites, and the presence of CdTe QDs can lead to an decrease of glass transition temperatures of polybutadiene (PB) and polystyrene(PS) domains. In addition, mechanical tests reveal that the addition of CdTe QDs is a useful approach to improve the mechanical properties of SBS. Meanwhile, the fluorescent photographs taken under ultraviolet light prove that SBS/CdTe QDs composites possess strong PL. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011.     

Polyoxymethylene/ethylene butylacrylate copolymer/ethylene‐methyl acrylate‐glycidyl methacrylate ternary blends

Blends of compatibilized polyoxymethylene (POM)/ethylene butylacrylate copolymer (EBA)/ethylene‐methyl acrylate‐glycidyl methacrylate copolymer (EMA‐GMA) and uncompatibilized POM/EBA were investigated. The notched impact strength of the compatibilized blends was higher than that of their uncompatibilized counterparts. The toughness of the POM blends was improved obviously with relatively low loading of EBA. Fourier transform infrared spectroscopy (FTIR) spectra of EMA‐GMA, pure POM, and POM/EBA/EMA‐GMA blends indicated that epoxy groups of EMA‐GMA reacted with terminal hydroxyl groups of POM molecular chains. The glass‐transition temperature (T_g) values of the POM matrix and the EBA phase were observed shifted to each other in the presence of EMA‐GMA compatibilizer indicating that the compatibilized blends had better compatibility than their uncompatibilized counterparts. With the addition of EBA to POM, both the compatibilized and uncompatibilized blends showed higher onset degradation temperature (T_d) than that of pure POM and the T_d values of the compatibilized blends were higher than those of their uncompatibilized counterparts. The scanning electron microscopy showed better EBA particles distribution state in the compatibilized system than in the uncompatibilized one. The compatibilized blend with an obvious rougher impact fracture surface indicated the ductile fracture mode. POLYM. ENG. SCI., 58:1127–1134, 2018. © 2017 Society of Plastics Engineers     

Miscibility and rheology behaviors of poly(3‐hydroxybutyrate)/poly(p‐vinylphenol) blends with homogeneous amorphous compositions

The miscibility and rheology behaviors of poly(3‐hydroxybutyrate) (PHB) and Poly(p‐vinylphenol) (PVPh) blends were studied in this work. It was evidenced that the miscible amorphous system of the PHB/PVPh blends was formed when the PHB content was less than 40%(wt). Linear dynamic viscoelasticity of the blends in the amorphous condition was studied through oscillatory shear measurements. Time‐temperature superposition principle (TTS) was applicable in the experimental window. The Han plots (log G′ versus log G″) were temperature independent, but the curvatures in the terminal region were much less than 2 and became smaller with increasing of the PVPh. It was considered that this phenomenon might come from the presence of the change of the whole hydrogen bonding (self‐associated and the hydrogen bonding between hydroxyl group and ester group) in the blends. The Fourier transform infrared spectroscopy analysis supported this conclusion. It was found that the rubber plateau modulus for this blend system did not follow Wu's and Tsenoglou's model. This result was also caused by the presence of the hydrogen bonding. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011.     

Dynamic Mechanical Properties of Poly(propylene) Blends with Poly[ethylene‐co‐(methyl acrylate)]

Summary: Blends of poly(propylene) (PP) were prepared with poly[ethylene‐co‐(methyl acrylate)] (EMA) having 9.0 and 21.5% methyl acrylate comonomer. A similar series of blends were compatibilized by using maleic anhydride grafted PP. The morphology and mechanical properties of the blends were investigated using differential scanning calorimetry (DSC) and dynamic mechanical analysis (DMA) in tensile mode. The DMA method and conditions were optimized for polymer film specimens and are discussed in the experimental section. The DSC results showed separate melting that is indicative of phase‐separated blends, analogous to other PP‐polyethylene blends but with the added polarity of methyl acrylate pendant side groups that may be beneficial for chemical resistance. Heterogeneous nucleation of PP was decreased in the blends because of migration of nuclei into the more polar EMA phase. The crystallinity and peak‐melting temperature did not vary significantly, although the width of the melting endotherm increased in the blends indicating a change had occurred to the crystals. DMA analysis showed the crystal‐crystal slip transition and glass transition (T_g) for PP as well as a T_g of the EMA copolymer occurring chronologically toward lower temperatures. The storage modulus of PP and the blends was generally greater with annealing at 150 °C compared with isothermal crystallization at 130 °C. The storage modulus of the blends for isothermally crystallized PP increased with 5% EMA, then decreased for higher amounts of EMA. Annealing caused a decrease with increasing copolymer content. The extent of the trend was greater for the compatibilized blends. The T_g of the blends varied over a small range, although this change was less for the compatibilized blends.

Storage modulus for PP and EMA9.0 blends annealed at 150 °C.     

Molecular simulation of miscibility of poly(2,6‐dimethyl‐1,4‐phenylene ether)/poly(styrene‐co‐acrylonitrile) blend with the compatibilizer triblock terpolymer SBM

Polymer blend of poly(2,6‐dimethyl‐1,4‐phenylene ether) (PPE) and poly(styrene‐co‐acrylonitrile) (SAN), which has broad commercial interest, has limited miscibility. A triblock terpolymer, polystyrene‐block‐polybutadiene‐block‐poly(methyl methacrylate) (SBM), is often used as compatibilizer to improve the miscibility of PPE/SAN. In this work, dissipative particle dynamics and molecular dynamics of Material Studio were used to study the essentials that influence miscibility of the blend systems, and then Flory–Huggins parameter χ, radial distribution function (RDF) and morphologies are analyzed. It shows that the blends with more content of styrene in SAN (above 90 wt%), whose mass percentage is 60%, are best miscible. For the systems of PPE/SAN added with SBM, the miscibility increases and then decreases with the increase of SBM content. A longer chain of styrene (S) in SBM leads to wrapped structure of PMMA by PB, wrapped by PS, resulting in decrease of the miscibility. From studies and simulation of χ and RDF, the best blend system for commercial and industrial use is the one with mass ratio of PPE/SAN/SBM 36/54/10, in which S content in SAN is above 90 wt%. For SBM, the ratio of chain length styrene (S)/butadiene (B) is lessthan 1, while B and M are the same in chain length. POLYM. COMPOS., 2011. © 2011 Society of Plastics Engineers     

Polyacetal/poly(tetrafluoroethylene) blends,I. The effect of Na-treated poly(tetrafluoroethylene) on polyacetal

The various properties of the blends of polyacetal (POM) with up to 20 wt.-% chemically surface-treated poly(tetrafluoroethylene) (CPTFE) were investigated and compared with those of POM/PTFE blends. The PTFE is added to POM to improve the wear properties, however, the mechanical properties of POM/PTFE blends decrease with increasing PTFE content, but tensile strength and Young's modulus of POM/CPTFE blends are more than 2 times higher than that of the POM/PTFE blends. SEM shows that the size of inherent agglomerative PTFE is in the range of 30 to 100 μm. The particle size of major CPTFE dispersed in POM is smaller than 1 μm.