Perfluorosulfonic acid—Tetraethoxysilane/polyacrylonitrile (PFSA‐TEOS/PAN) hollow fiber composite membranes prepared for pervaporation dehydration of ethyl acetate–water solutions

Preparation of organic‐inorganic composite membranes and their pervaporation (PV) permeation and separation characteristics for the aqueous solution of ethyl acetate were described. Polyacrylonitrile (PAN) hollow fiber ultrafiltration membrane as support membrane, the mixtures of perfluorosulfonic acid (PFSA) and tetraethoxysilane (TEOS) by the sol‐gel reaction as the coating solution, the PFSA‐TEOS/PAN hollow fiber composite membranes by the different annealing conditions were prepared. The swelling of PFSA in ethyl acetate aqueous solutions was inhibited with addition of TEOS. The PFSA‐TEOS/PAN composite membranes containing up to 30 wt % TEOS in coating solution exhibited high selectivity towards water, then the selectivity decreased and permeation flux increased with increasing the TEOS concentration more than 30 wt %. When the PFSA‐TEOS/PAN composite membranes were annealed, the separation factor increased with increasing annealing temperature and time. Higher annealing temperature and longer annealing time promoted the crosslinking reaction between PFSA and TEOS in PFSA‐TEOS/PAN composite membranes, leading to the enhanced selectivity towards water. For the PFSA/PAN and PFSA‐TEOS/PAN composite membrane with 5 and 30 wt % TEOS annealed at 90°C for 12 h, their PV performance of aqueous solution 98 wt % ethyl acetate were as follows: the separation factors were 30.8, 254 and 496, while their permeation flux were 1430, 513 and 205 g/m² h at 40°C, respectively. In addition, the PV performance of PFSA‐TEOS/PAN composite membranes was investigated at different feed solution temperature and concentration. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Pervaporation dehydration of water/ethanol/ethyl acetate mixtures using poly(vinyl alcohol)–silica hybrid membranes

The novel organic–inorganic hybrid membranes were prepared from poly(vinyl alcohol) (PVA) and vinyltriethoxysilane (VTES). They were characterized using Fourier transform infrared (FTIR), X‐ray diffraction (XRD), scanning electron microscopy (SEM), atomic force microscopy (AFM), thermogravimetric analysis (TGA), and contact angle metering. The as‐prepared membranes are formed at a molecular scale at a low VTES content. Aggregations in the surface of the as‐prepared membranes were clearly evident above 18.43 wt % VTES loading. The introduction of VTES into the PVA matrix resulted in a decrease in the crystalline and an increase in compactness and thermal stability of the as‐prepared membranes. Silica hybridization reduced the swelling of the as‐prepared membranes in water/ethanol/ethyl acetate mixtures, decreased the permeation flux, and remarkably enhanced water permselectivity in pervaporation dehydration of ethanol/ethyl acetate aqueous solution. The hybrid membrane with 24.04 wt % VTES has the highest separation factor of 1079 and permeation flux of 540 g m^?2 h^?1. © 2012 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Pervaporation separation of water/isopropanol mixtures through crosslinked carboxymethyl chitosan/polysulfone hollow‐fiber composite membranes

Carboxymethyl chitosan (CMCS)/polysulfone (PS) hollow‐fiber composite membranes were prepared through glutaraldehyde (GA) as the crosslinking agent and PS hollow‐fiber ultrafiltration membrane as the support. The permeation and separation characteristics for dehydration of isopropanol were investigated by the pervaporation method. Pure chitosan, carboxymethyl chitosan, and crosslinked carboxymethyl chitosan membranes were characterized by Fourier transform infrared (FT‐IR) spectroscopy and X‐ray diffraction (XRD) to study the crosslinking reaction mechanism and degree of crystallinity, respectively. The effects of feed composition, crosslinking agent, membrane thickness, and feed temperature on membrane performance were investigated. The results show that the crosslinked CMCS/PS hollow‐fiber composite membranes possess high selectivity and promising permeability. The permeation flux and separation factor for isopropanol/water is 38.6 g/m²h and 3238.5, using 87.5 wt % isopropanol concentration at 45°C, respectively. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 103: 1959–1965, 2007     

Positively charged composite nanofiltration membrane prepared by poly(N,N‐dimethylaminoethyl methacrylate)/polysulfone

Poly(N,N‐dimethylaminoethyl methacrylate) (PDMAEMA) can be crosslinked by quaternization to develop a positively charged dense network structure. According to this mechanism, PDMAEMA/polysulfone (PSF) positively charged nanofiltration membrane was developed by interfacial crosslinking polymerization using PSF plate microfiltration membrane as support layer, PDMAEMA aqueous solution as coating solution, and p‐xylylene dichloride/n‐heptane as crosslinking agent. Technique and condition of developing membrane such as concentration of coating solution, coating time, pH value of coating solution, content of low molecular weight additive in coating solution, concentration of crosslinking agent, crosslinking time, and number of coatings were studied. FTIR, SEM, and X‐ray photoelectron spectroscopy were used to characterize the structure of membranes. This membrane had rejection to inorganic salts in water solution, the rejection rate to MgSO₄ (1 g/L water solution at 0.8 MPa and 30°C) was about 90%, and permeation flux was about 10–20 L m^?2 h^?1. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 91: 2721–2728, 2004     

Solvent and pH resistance of surface crosslinked chitosan/poly(acrylonitrile) composite nanofiltration membranes

The resistance of novel surface crosslinked Chitosan/poly(acrylonitrile) (PAN) composite nanofiltration (NF) membranes to pH and organic solvents was studied with respect to the effects of crosslinking parameters, namely, glutaraldehyde concentration and crosslinking time. The pH resistance was determined by permeation of aqueous acidic (pH 2.5) and basic (pH 11) solutions as well as swelling studies in the pH range of 2.5–11. The solvent resistance was determined by swelling, immersion, and permeation studies with several industrially important organic solvents, namely methanol, ethanol, iso‐propanol, methyl ethyl ketone, ethyl acetate and hexane. It was observed that the crosslinked composite membranes maintain the permeate fluxes for test solvents for 2 h of continuous operation without any significant change in flux. SEM studies on membrane samples after immersion as well as permeation with the above‐mentioned solvents indicated that the membrane morphology was maintained. The results are explained in terms of solvent–membrane polar and hydrophobic interactions, using solubility parameters of membrane and solvents and dielectric constants of solvents. Pure water flux and polyethylene glycol transmission data indicated that at pH 2.5 and 11, the membrane stability increased with increasing glutaraldehyde concentration and was much better at pH 11 than at pH 2.5. All surface crosslinked membranes showed reduced swelling between pH 4–10. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 77: 1782–1793, 2000     

Synthesis and characterization of poly(ether‐block‐amide) membranes for the pervaporation of organic/aqueous mixtures

We made poly(ether‐block‐amide) membranes by casting a solution on a nonsolvent surface. The effects of the solvent ratio (n‐butanol/isopropyl alcohol), temperature, and polymer concentration on the quality of the membranes were studied. The results show that the film quality was enhanced with increasing isopropyl alcohol ratio in the solvent. This behavior was related to the reduction of the solution surface tension and the interfacial tension between the solution and nonsolvent. Uniform films were made at a temperature range of 70–80°C and a polymer concentration of 4–7 wt %. The morphology of the membranes was investigated with scanning electron microscopy. The qualities of the films improved with increasing isopropyl alcohol ratio in the solvent. With these membranes, the pervaporation of ethyl butyrate (ETB)/water and isopropyl alcohol/water mixtures was studied, and high separation performance was achieved. For ETB/water mixtures, with increasing ETB content, both the permeation flux and separation factor increased. However, for isopropyl alcohol/water mixtures, with increasing isopropyl alcohol content, the permeation flux increased, but the separation factor was diminished. Increasing temperature in a limited range resulted in a decreasing separation factor and an increasing permeation flux. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Preparation of PFSA‐PVA/PSf hollow fiber membrane for IPA/H2O pervaporation process

Using Na⁺ form of perfluorosulfonic acid (PFSA) and poly(vinyl alcohol) (PVA) as coating materials, polysulfone (PSf) hollow fiber ultrafiltration membrane as a substrate membrane, PFSA‐PVA/PSf hollow fiber composite membrane was fabricated by dip‐coating method. The membranes were post‐treated by two methods of heat treatment and by both heat treatment and chemical crosslinking. Maleic anhydride (MAC) aqueous solution was used as chemical crosslinking agent using 0.5 wt % H₂SO₄ as a catalyst. PFSA‐PVA/PSf hollow fiber composite membranes were used for the pervaporation (PV) separation of isopropanol (IPA)/H₂O mixture. Based on the experimental results, PFSA‐PVA/PSf hollow fiber composite membrane is suitable for the PV dehydration of IPA/H₂O solution. With the increment of heat treatment temperature, the separation factor increased and the total permeation flux decreased. The addition of PVA in PFSA‐PVA coating solution was favorable for the improvement of the separation factor of the composite membranes post‐treated by heat treatment. Compared with the membranes by heat treatment, the separation factors of the composite membranes post‐treated by both heat treatment and chemical crosslinking were evidently improved and reached to be about 520 for 95/5 IPA/water. The membranes post‐treated by heat had some cracks which disappeared after chemical crosslinking for a proper time. Effects of feed temperature on PV performance had some differences for the membranes with different composition of coating layer. The composite membranes with the higher mass fraction of PVA in PFSA‐PVA coating solution were more sensitive to temperature. It was concluded that the proper preparation conditions for the composite membranes were as follows: firstly, heated at 160°C for 1 h, then chemical crosslinking at 40°C for 3 h in 4% MAC aqueous solution. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Vapor permeation of ethyl acetate,propyl acetate,and butyl acetate with hydrophobic inorganic membrane

This study is focused on the permeation characteristics of ester compounds from aqueous solutions through hydrophobic membrane; ethyl acetate (EA), propyl acetate (PA) and butyl acetate (BA). A surface-modified tube-type alumina membrane (Al₂O₃) was used for ester compounds recovery by vapor permeation. Experiments were performed to evaluate the effects of the feed concentration (0.15–0.60 wt.%) and feed temperature (30–50 °C) on the separation of EA, PA, and BA from dilute aqueous solutions. It was found that the permeation flux increased with increasing feed ester concentration and operating temperature. The fluxes of EA, PA, and BA at 0.60 wt.% feed concentration and 40 °C were 282, 526, 661 g/m² h, which were much higher than those of polymer membranes. The separation factors for the 0.15–0.60 wt.% feed solution of EA, PA, and BA at 40 °C were in the range of 28.1–93.9, 83.6–129.4, and 190.7–209.9, respectively. The membrane tested showed high flux and high selectivity.     

Pervaporation characteristics and structure of poly(vinyl alcohol)/poly(ethylene glycol)/tetraethoxysilane hybrid membranes

Poly(vinyl alcohol) (PVA) blended with poly(ethylene glycol) (PEG) was crosslinked with tetraethoxysilane (TEOS) to prepare organic–inorganic PVA/PEG/TEOS hybrid membranes. The membranes were then used for the dehydration of ethanol by pervaporation (PV). The physicochemical structure of the hybrid membranes was studied with Fourier transform infrared spectra (FT‐IR), wide‐angle X‐ray diffraction WXRD, and scanning electron microscopy (SEM). PVA and PEG were crosslinked with TEOS, and the crosslinking density increased with increases in the TEOS content, annealing temperature, and time. The water permselectivity of the hybrid membranes increased with increasing annealing temperature or time; however, the permeation fluxes decreased at the same time. SEM pictures showed that phase separation took place in the hybrid membranes when the TEOS content was greater than 15 wt %. The water permselectivity increased with the addition of TEOS and reached the maximum at 10 wt % TEOS. The water permselectivity decreased, whereas the permeation flux increased, with an increase in the feed water content or feed temperature. The hybrid membrane that was annealed at 130°C for 12 h exhibited high permselectivity with a separation factor of 300 and a permeation flux of 0.046 kg m^?2 h^?1 in PV of 15 wt % water in ethanol. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

Pervaporation of chlorinated hydrocarbon-acetone mixtures through poly(ethylene-co-vinyl acetate) membranes

Crosslinked and uncrosslinked ethylene-vinyl acetate copolymer membranes were prepared. The permeation characteristics in the pervaporation process were examined using carbon tetrachloride-acetone mixtures. Modified membranes exhibit carbon tetrachloride permselectivity, but unmodified membranes did not display the permselectivity of crosslinked polymer. Furthermore, membranes modified with dicumyl peroxide (DCP) showed a higher flux and selectivity than those of benzoyl peroxide (BP) modified ones. The effects of feed concentration, molecular size, and polarity of the permeating species on pervaporation were analyzed. The influence of crosslinking density of the membranes on pervaporation was also analyzed. The maximum separation and flux were found to be associated with an optimum amount of crosslinking agent in the membrane. A mixture of chloroform and acetone having a composition near the azeotropic region was also separated by the pervaporation technique. © 1996 John Wiley & Sons, Inc.     

响应面优化法在PDMS/PVDF膜制膜条件优化中的应用

用响应面优化法优化了乙烯基封端PDMS/PVDF渗透汽化透醇膜的制膜条件,研究了硅橡胶浓度、B/A质量比、交联温度和交联时间对膜性能的影响,拟合了分离因子、渗透通量与四因素之间的回归方程,并用方差分析法考察了四因素的主效应、二次效应以及相互作用效应对复合膜的分离因子与渗透通量的影响。研究发现,硅橡胶浓度对膜的分离因子与渗透通量的影响最为显著,交联时间对分离因子几乎没有影响。通过对回归方程的优化分析得知,在料液乙醇浓度为10%(wt),操作温度40℃条件下,当硅橡胶浓度为93%(wt),B/A质量比为0.08,交联温度为100℃,交联时间为13.83 h时,膜的综合分离性能达到最佳,此时分离因子与渗透通量预测值分别为9.47、77.57 g(m2 h)1,渗透侧乙醇浓度达到51.3%(wt)。回归方程的验证实验结果表明,回归方程的估计值与实验值较为吻合,可用于乙烯基封端的PDMS/PVDF复合膜的渗透汽化性能的预测与优化。     

Modified poly(vinyl alcohol)/chitosan blended membranes for isopropanol dehydration via pervaporation: Synthesis optimization and modeling by response surface methodology

Box–Behnken (BB) design of response surface methodology (RSM) was effectively applied to optimize fabrication conditions of modified poly(vinyl alcohol) (PVA) and chitosan (CS) blended pervaporation (PV) membranes. The PVA/CS membranes were crosslinked either by chemical reaction with glutaraldehyde (GA) or by heat‐treating at different temperatures. The main objectives were to determine the optimal levels of fabricating parameters and also to investigate interactions among the variables. CS content in the blended membranes, concentration of crosslinking agent and heat‐treating temperature were the fabrication parameters, the main effects and interaction effects of which on membrane structure and PV performance toward isopropanol (IPA)/water dehydration were investigated, and for which regression models were established. The modified PVA/CS blended membranes were characterized by means of scanning electron microscopy (SEM), Fourier transform infrared spectroscopy (FTIR) as well as X‐ray diffraction (XRD). It was found that the CS content is the most significant factor influencing flux and separation factor among the three studied variables and the experimental results are in excellent accordance with predicted values from the developed RSM regression models. The RSM results indicated that under preparation conditions of 80 wt % CS in the blended membrane, 0.58 wt % GA concentration, and 77 °C heat‐treating temperature, the maximum separation factor of 5222.8 and the normalized flux of 9.407 kg µm/m²h can be acquired with feed content of 85 wt % IPA at 25 °C, showing that the prepared membrane is highly efficient for PV dehydration of IPA. The models were satisfactorily validated against experimental data. Furthermore, the optimum membrane presents excellent separation performance at different feed compositions and temperatures. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 44587.     

Preparation and properties of a salt‐resistant superabsorbent polymer

Crosslinked sodium polyacrylate was prepared by solution polymerization with N,N‐methylene‐bisacrylamide (bisAM) as crosslinking agent; it was subsequently surface‐crosslinked by ethylene glycol diglycidyl ether (EGDE) and then was modified with inorganic salt to obtain a superabsorbent with water absorbency in 0.9 wt % NaCl aqueous solution at atmosphere and applied pressure (P ≈ 2 × 10³ Pa) of 55 and 20 g.g^?1, respectively. Moreover, it also had excellent hydrogel strength. The effects of reaction temperature, reaction time, neutralization degree (ND) of acrylic acid, amount of initiator, crosslinking agent, and surface‐crosslinking agent, mass ratio of inorganic salt to initial superabsorbent, molar ratio of sodium aluminate (NaAlO₂) to potassium dihydrogen hyphosphate (KH₂PO₄) on water absorbency (WA) in 0.9 wt % NaCl aqueous, and the hydrogel modulus were investigated and optimized. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 93: 2532–2541, 2004     

Blend membranes of chitosan and poly(vinyl alcohol) in pervaporation dehydration of isopropanol and tetrahydrofuran

Blend membranes of a natural polymer, chitosan, with a synthetic polymer, poly(vinyl alcohol) (PVA), were prepared by solution casting and crosslinked with a urea formaldehyde/sulfuric acid (UFS) mixture. Chitosan was used as the base component in the blend system, whereas PVA concentration was varied from 20 to 60 wt %. Blend compatibility was studied by differential scanning calorimetry, and Fourier transform infrared spectroscopy was used to study membrane crosslinking. Membranes were tested for pervaporation dehydration of isopropanol and tetrahydrofuran (THF) at 30°C in close proximity to their azeotropic compositions. Membrane performance was assessed by calculating flux and selectivity. Swelling experiments performed in water + organic mixtures at 30°C were used to explain the pervaporation results. The blend membrane containing 20 wt % PVA when tested for 5 and 10 wt % water–containing THF and isopropanol feeds exhibited selectivity of 4203 and 17,991, respectively. Flux increased with increasing concentration of water in the feed. Selectivity was highest for the 20 wt % PVA‐containing blend membrane. The results of this study are unique in the sense that the crosslinking agent used—the UFS mixture—was novel. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 103: 1918–1926, 2007     

Construction of efficient desalting layer on a cellulose acetate membrane by acetalized surface crosslinking treatment

For the purpose of enhancing the desalination performance, a desalting layer was successfully constructed on a cellulose acetate (CA) virgin membrane via acetalized surface crosslinking treatment. The acetalization crosslinking reaction consists of two hydroxyl groups reacting with one aldehyde group to remove one molecule of water. Results showed that the reaction occurred on the surface of the CA membrane, as measured by Fourier‐transform infrared (FTIR), differential scanning calorimeter (DSC), X‐ray photoelectron spectroscopy (XPS), and scanning electron microscope (SEM). The water flux and desalination performance were compared before and after crosslinking, and the formation of the desalting layer greatly improved the desalination performance of the membrane. In addition, the crosslinking temperature, crosslinking time, and formaldehyde solution mass fraction of the CA membrane structure and performance were explored. It was observed that the CA flat membrane showed better desalination performance, with a salt rejection rate of 98.55% and a water flux of 9.88 L/(m²·h), under a processing temperature of 100 °C 11% formaldehyde solution mass fraction and a crosslinking time of 60 min. POLYM. ENG. SCI., 59:913–918, 2019. © 2018 Society of Plastics Engineers     

γ-(2,3环氧丙氧)丙基三甲氧基硅烷改性壳聚糖渗透蒸发杂化膜的制备及乙醇脱水性能研究

通过γ-缩水甘油醚氧丙基三甲氧基硅(KH-560)对壳聚糖进行交联改性制备乙醇脱水渗透蒸发杂化膜.实验结果表明偶联剂的加入能有效提高壳聚糖膜的分离效果,随着偶联剂含量的增加,杂化膜的对水的选择性先增加后下降,在2％(质量分数)时有最好的选择性.膜的分离因子随着进料温度的增大而降低,随着乙醇浓度的增大而增大;通量随着进料温度的增大而增大,随着乙醇浓度增大而减小.硅烷偶联剂/壳聚糖杂化膜呈现出良好的渗透蒸发分离性能,当进料乙醇浓度为95％(质量分数),温度为35℃时,通量和分离因子分别为134g/(h·m2)和97214.     

Properties of modified poly(vinyl alcohol) membranes prepared by the grafting of new polyelectrolyte copolymers for water–ethanol mixture separation

For the preparation of a water‐selective membrane for the pervaporation separation of an azeotropic solution, a series of grafted copolymers were synthesized by the reaction of poly(vinyl alcohol) (PVA) with poly(sodium salt styrene sulfonic acid‐co‐maleic acid) (PSStSA‐co‐MA). The esterification was performed between the hydroxyl groups of PVA and the carboxylic groups of the copolymer with a heat treatment. PSStSA‐co‐MA was prepared with sodium salt styrene sulfonic acid and maleic anhydride copolymerization in dimethyl sulfoxide with azobisisobutyronitrile as an initiator. The reaction mechanism and resultant structure were confirmed with IR spectra. The effect of the heat‐treatment time on the gel content was investigated. The permeation flux decreased and the separation factor increased as the crosslinking agent content rose. A membrane containing 15 wt % PSStSA‐co‐MA was used for water–ethanol azeotropic solution pervaporation at 30°C, and a flux of 0.43 kg/m² h and a separation factor of 190 were obtained. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 86: 2854–2859, 2002     

EC-AHBPE渗透汽化膜的研究

为研究超支化聚合物在渗透汽化分离膜中的应用,该文以三羟甲基丙烷为核、二羟甲基丙酸为单体,用准一步法合成了端羟基超支化聚酯(HBPE),并以丙烯酸对其进行了端基改性,得到端丙烯酸酯基超支化聚酯(AHBPE)。将AHBPE作为大分子交联剂,对乙基纤维素(EC)进行紫外光引发交联改性,得到了EC-AHBPE膜。以苯/环己烷体系为考察对象,对EC-AHBPE膜的吸附溶胀行为和渗透汽化性能进行了考察,并与小分子交联剂乙二醇二丙烯酸酯交联EC膜进行了比较。结果表明:与小分子交联剂乙二醇二丙烯酸酯(EGDM)相比,AHBPE交联膜具有更高的平衡吸附量和吸附选择性。当AHBPE在膜内质量分数为40%、交联时间为30 min、二苯甲酮质量分数为10%时,对于苯质量分数为10%的混合溶液,EC-AHBPE膜的渗透通量可达42.5 kg.μm/(m2.h),分离因子为7.02。     

Synthesis,Evaluation, and Gelation Mechanism of Organic Chromium

Since the launching of tertiary oil recovery, the performance requirements of polymer solution increasing, the polymer solution is more difficult to meet the needs of the scene. It could solve poor profile control, salt‐tolerant, and poor performance that crosslinking agent was added to polymer solution. Therefore, chromium acetate crosslinker was synthesized, and the synthesis conditions were optimized, and the performance of crosslinking agent was evaluated. Through optimization, the optimum conditions of chromium acetate synthesis was: reaction time 10 h, reaction temperature 80°C, the molar ratio of acetic acid and potassium dichromate than or equal to 24 : 1. Performance evaluation showed that adding crosslinking agent could significantly increase the viscosity of the polymer solution, could significantly improve the resistance coefficient and residual resistance of the polymer solution, and could play a good role profile flooding. Studies showed that when salinity and ion content changed, the crosslinking mechanism of changed. Through the study of molecule coil size at room temperature, the molecule coil size would slightly decline after 1 h, suggesting that crosslinking mechanism was intramolecular crosslinking reaction occurs at first, and then intermolecular crosslinking reaction. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

PDMS/PVDF microporous membrane with semi‐interpenetrating polymer networks for vacuum membrane distillation

In this article, using the non‐solvent induced phase separation process, a new microporous membrane with the semi‐interpenetrating polymer network (semi‐IPN) structure was produced. For this membrane, polydimethylsiloxane (PDMS) polymer is crosslinking and poly(vinylidene fluoride) (PVDF) polymer is linear, by changing the mass ratio of PDMS/PVDF, the structure and the performance of the prepared membranes were studied. The membranes were also investigated by attenuated total reflection‐Fourier transform infrared (ATR‐FTIR), scanning electron microscopy–energy‐dispersive X‐ray spectroscopy, X‐ray diffraction, thermogravimetric analysis, and water contact angle, etc. ATR‐FTIR spectroscopy confirmed the formation of semi‐IPN; compared with the PDMS/PVDF polymer without semi‐IPNs structure, the viscosity of the semi‐IPNs structured casting solution increased, membrane mechanical property increased but its hydrophobicity decreased. Using the resulting membranes for the vacuum membrane distillation desalt of the NaCl solution (30 g/L), 99.9% salt rejection and reasonable flux were obtained. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 45792.