The effect of irradiation on morphology and properties of the PET/HDPE blends with trimethylol propane trimethacrylate (TMPTA)

The mechanical properties of poly(ethylene terephthalate)/high-density poly(ethylene) (PET/HDPE) blends were improved by γ-ray irradiation combined with using a cross-linking agent—trimethylol propane trimethacrylate (TMPTA). The effect of the weight ratio of PET/HDPE, the content of TMPTA and the absorbed dose on the phase morphology and the mechanical properties of the PET/HDPE blends were investigated through scanning electron microscopy (SEM), gel fraction, Fourier transform infrared spectroscopy (FTIR), tensile and impact tests. SEM images showed that the phase structure changed significantly as TMPTA coexistence. The results of tensile and impact tests indicated that their mechanical properties depended on their structures. FTIR spectra suggested that a new structure of HDPE-g-PET was generated. When the weight ratio of PET/HDPE blend was 80/20, the content of TMPTA was 1 wt% and the absorbed dose was 30 kGy, the tensile strength, elongation at break and impact strength of irradiated blends were improved greatly compared with non-irradiated blends.     

Crosslinking of polyvinyl chloride by electron beam irradiation in the presence of ethylene–vinyl acetate copolymer

Electron beam (EB) irradiation of polyvinyl chloride (PVC) was carried out in the presence of three different ethylene–vinyl acetate copolymers (EVA). The mechanical properties of the original and irradiated blends were tested. The gel content measurement, chlorine loss upon electron irradiation, and gel permeation chromatograph (GPC) were used to characterize the effect of EVA on the irradiation behavior of PVC/EVA blends. The content and the chemical structure of EVA in the blends had considerable effects on the mechanical properties and gel content of the blends. The incorporation of EVA into PVC blend can increase the gel content and reduce chlorine loss of the blends. The GPC analysis of the soluble part in the irradiated PVC samples showed that the addition of EVA into the PVC blend lowered the polydispersity of molecular weight of PVC. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 91: 1571–1575, 2004     

Effect of electron beam irradiation and vinyl acetate content on the physicochemical properties of LDPE/EVA blends

The radiation‐induced crosslinking, compatibility, and surface modification of low density polyethylene/ethylene vinyl acetate blends (LDPE/EVA) were investigated. The structural and physical properties were characterized in terms of gel content, hot set, mechanical properties, contact angle, and surface free energy. The highest crosslink density was obtained at 20 wt % of EVA. Gel content of LDPE/EVA blends was increased with increasing irradiation dose, vinyl acetate (VA), and EVA contents. The hot set results are consistent with the gel content data. Mechanical testing showed that the tensile strength of samples increased with increasing irradiation dose up to 180 kGy, whereas the elongation at break was decreased with increasing irradiation dose. Contact angle measurements showed that the surface hydrophillicity of LDPE blend was increased with increasing irradiation dose and contents of both VA and EVA. The surface free energy was greatly dependent on irradiation dose and content of both VA and EVA. The total surface free energies of different LDPE formulations were in the range 17.25–32.51 mN/m, in which the polar (^pσ) and disperse (^dσ_s) values were within the range 16.52–26.6 and 0.9–5.91 mN/m, respectively. In conclusion, electron beam irradiation and blending LDPE with EVA improved the wettability or adhesion properties of LDPE/EVA blends. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

Effect of trimethylolpropane triacrylate (TMPTA) on the properties of irradiated epoxidized natural rubber (ENR‐50), ethylene‐(vinyl acetate) copolymer (EVA), and an ENR‐50/EVA blend

The effect of trimethylolpropane triacrylate (TMPTA) monomer on the tensile properties, dynamic mechanical properties, and morphology of irradiated epoxidized natural rubber (ENR‐50), ethylene‐(vinyl acetate) copolymer (EVA), and an ENR‐50/EVA blend was investigated. The ENR‐50, EVA, and ENR‐50/EVA blend were irradiated by using a 3.0‐MeV electron‐beam apparatus at doses ranging from 20 to 100 kGy. The improvement of tensile properties and morphology with irradiation indicated the advantage of having irradiation‐induced crosslinks in these materials. Observation of the properties studied confirmed that TMPTA was efficient in enhancing the irradiation‐induced crosslinking of ENR‐50, EVA, and the ENR‐50/EVA blend. Addition of TMPTA improved the adhesion between the ENR‐50/EVA blend phases by forcing grafting and crosslinking at a higher irradiation dose (100 kGy). J. VINYL ADDIT. TECHNOL., 2009. © 2009 Society of Plastics Engineers.     

Mechanical,Thermal and Electrical Properties of Ethylene Vinyl Acetate Irradiated by an Electron-Beam

The effects of electron beam irradiation of (ethylene vinyl acetate) EVA containing 18% vinyl acetate was studied. The EVA sample was then irradiated by using 3 MeV electron beam machine at doses ranging from 120 to 360 kGy in air at room temperature and analyzed for mechanical, thermal and electrical properties. It was revealed by DSC analysis that the crystallinity of the electron-beam radiated EVA decreased slightly as verified by a marginal reduction in the densities and heats of melting. Thermal degradation of EVA occurred through two steps as shown by the thermogravimetric curve with maximum rates of 350 and 450°C, respectively. The results obtained from both gel content and hot set tests showed that under the irradiation conditions employed, the EVA sample cross-linked by the electron beam irradiation, and the degree of cross-linking in the amorphous regions was dependent on the irradiation dose. A significant improvement in the tensile strength of the neat EVA samples was obtained upon electron-beam radiation up to 210 kGy with a concomitant decline in elongation of break. Various electrical properties of EVA such as surface and volume resistance, breakdown voltage and dielectric constant were studied as a function of radiation dose. It was revealed that the surface resistance and volume resistivity of the EVA reaches a maximum at a 190 kGy dose of radiation. No considerable change of breakdown voltage and dielectric constant was observed with increasing irradiation dose. These studies suggest that radiation-cured EVA is more thermally and mechanically stable than pure EVA. Similarly, the results from the electrical properties revealed that surface and volume resistance are higher than pure EVA.     

Effect of electron beam radiation on mechanical and electrical properties of poly(ethylene-co-vinyl acetate)

Ethylene-vinyl acetate (EVA) copolymer (12% vinyl acetate content) is subjected to electron beam irradiation using trimethylolpropane trimethacrylate (TMPTMA) as a radiation sensitizer. Mechanical and electrical studies of these irradiated samples show that the strength properties (tensile strength, elongation at break) are increased with radiation dosage up to an optimum radiation dose and sensitizer level above which the properties begin to deteriorate. Crosslinking of the polymer takes place on irradiation which is attributed to an increased gel content with increasing radiation dose. Compared to the original samples both dielectric constant and dielectric loss factor decrease for samples subjected to irradiation.     

Investigation of radiation-crosslinked foam of LDPE/EVA blends

Low-density polyethylene/ethylene–vinyl acetate copolymer (LDPE/EVA) blend was irradiated by γ-ray and then expanded by heat as a foamed material. The EVA content in the LDPE/EVA blend was benefited to form a gel. The gel fraction values of LDPE/EVA blend with 30% EVA content were higher than those of other blends in a same given dose; its gel fraction value was 1.7 times as those values of the LDPE without EVA. The gel fractions of the LDPE/EVA blend were increased with radiation dose in oxygen, in air, and in nitrogen, and the formation of gel was limited by oxygen. The oxidation products of the foam of the LDPE/EVA blend were observed in nitrogen, in oxygen by Fourier transform IR spectra. The LDPE/EVA blend system has no protection effect from oxidation in comparison with the LDPE system without EVA, which has less oxidation product than those without EVA in a same given gel fraction. The gel fraction of the LDPE/EVA blend around 25–35%, radiation dose 25±5 kGy, irradiated by γ-ray in air or in nitrogen, with higher expansion ratio (19), smaller cell diameter (0.175 mm), lower apparent density (0.042 g/cm³), higher tensile strength (0.40 MPa), and longer elongation at break (290–360%) foam of the LDPE/EVA blend were selected. These were optimum condition for application in this system. The relations among gel fraction of the LDPE/EVA blend, expansion ratio, apparent density, average cell diameter, and mechanical properties of the foam were discussed. © 1996 John Wiley & Sons, Inc.     

The effect of trimethylol propane tetraacrylate (TMPTA) and organoclay loading on the properties of electron beam irradiated ethylene vinyl acetate (EVA)/natural rubber (SMR L)/organoclay nanocomposites

Ethylene vinyl acetate (EVA)/natural rubber (SMR L)/organoclay nanocomposites were prepared by melt blending technique with 0–10 phr organoclay loading and 3 phr TMPTA. Electron beam initiated crosslinking on these samples was carried out using a 3.0 MeV electron beam machine with doses ranging from 50 to 200 kGy. XRD results proved that dispersion of organoclay in the nanocomposites was slightly improved by irradiation with TMPTA. This was further supported by transmission electron microscopy images, where the nanoscale dispersion of organoclay was more homogenous throughout the irradiated polymer matrix compared to nonirradiated samples. TMPTA also increased the gel fraction yield, tensile properties and thermal stability of the irradiated neat EVA/SMR L and its nanocomposites. TMPTA was found to act as a crosslink initiator, which promotes crosslink bridges via free radical mechanism in EVA/SMR L matrix. SEM observation shows that the fracture behavior of the irradiated neat EVA/SMR L and its nanocomposites with TMPTA is significantly different compared to the fracture behavior of the nonirradiated neat EVA/SMR L. The distinct failure surface structure formed in the irradiated samples with TMPTA explains the overall higher value of tensile properties. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Effect of surfactant and electron treatment on the electrical and thermal conductivity as well as thermal and mechanical properties of ethylene vinyl acetate/expanded graphite composites

This study presents an investigation of the electrical and thermal conductivities of composites based on an ethylene vinyl acetate (EVA) copolymer matrix and nanostructured expanded graphite (EG). To improve the EG dispersion in EVA, EG sheets were modified by treating them with the anionic surfactant sodium dodecyl sulphate (SDS) in water. The modified SDS‐EG platelets, after being filtered and dried, were melt‐mixed with EVA to prepare the composites. Finally, both EVA/EG and EVA/SDS‐EG composites were subjected to 50 kGy electron beam (EB) irradiation. SEM images confirm that the irradiated EVA/EG samples had improved interfacial adhesion, while the irradiated EVA/SDS‐EG samples showed even better interfacial adhesion. The gel contents of the irradiated samples without and with SDS treatment increased with increase in EG loading. The EVA/EG composites exhibited a sharp transition from an insulator to a conductor at an electrical percolation threshold of 8 wt %, but with SDS‐EG the electrical conductivity was extremely low, showing no percolation up to 10 wt % of filler. The EB irradiation had no influence on electrical conductivity. The thermal conductivity linearly increased with EG content, and this increase was more pronounced in the case of SDS‐EG, but decreased after EB irradiation. The thermal properties were little influenced by EB irradiation, while better polymer–filler interaction and better filler dispersion as a result of SDS treatment, and the EB irradiation initiated formation of a cross‐linked network, had a positive effect on the tensile properties. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42396.     

Effects of High-Energy Electron Beam Irradiation on the Properties of Flame-Retardant HDPE/EVA/Mg(OH)2 Composites

The mechanical properties of flame-retardant high-density polyethylene/ethylene vinyl-acetate copolymer/magnesium hydroxide (HDPE/EVA/Mg(OH)₂) composites for cable materials are usually poor due to the high loading of the filler. In this study, high-energy electron beam irradiation was applied to HDPE/EVA/Mg(OH)₂ composites in the presence of triallylisocyanurate, an irradiation sensitizer. The effects of high-energy electron beam irradiation on the properties of irradiated HDPE/EVA/Mg(OH)₂ composites were investigated through the measurements of gel content, limiting oxygen index, tensile testing, thermogravimetric analysis, and scanning electron microscope. The results showed that the thermal, mechanical and flame-retardant properties of the HDPE/EVA/Mg(OH)₂ composites were improved by using high-energy electron beam irradiation.     

Vinyl acetate content and electron beam irradiation directed alteration of structure,morphology, and associated properties of EVA/EPDM blends

A series of ethylene vinyl acetate/ethylene–propylene diene elastomer (EVA/EPDM) blends with four types of EVAs with various vinyl acetate (VA) content, are prepared without and with crosslinker, trimethylol propane triacrylate (TMPTA). These are irradiated by electron beam (EB). As the VA content increases, the gel content, i.e., degree of crosslinking of EVA/EPDM blends, is increased. With increase in VA content, the modulus and tensile strength are decreased but elongation at break is increased due to increase in amorphousness. On EB irradiation, modulus and tensile strengths are increased but at the cost of elongation at break. Crystallinities of all blends are decreased with increase in VA and EB crosslinking. The thermal stability of EVA/EPDM blend is decreased with increase in VA content but increased after EB irradiation. Scanning electron microscopy (SEM) and Fourier transform infrared spectroscopy (FTIR) show that with increase in VA content the miscibility of two polymers keeps on increasing, which even become more after EB irradiation. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43468.     

电子束辐照和氢氧化铝对LLDPE/EVA共混物凝胶含量和力学性能的影响

研究了电子束辐照剂量和氢氧化铝(ATH)的含量对线性低密度聚乙烯(LLDPE)/乙烯-醋酸乙烯酯(EVA)共混物凝胶含量和力学性能的影响。辐照剂量是影响LLDPE/EVA/ATH阻燃体系凝胶含量的主要因素,而ATH对其凝胶含量的影响较小。随着ATH含量的增加,LLDPE/EVA共混物的拉伸强度逐步增加,断裂伸长率迅速下降。所有阻燃体系的拉伸强度均是随着辐照剂量的增加而逐步增大,但辐照剂量对这些阻燃体系的断裂伸长率的影响却比较复杂。     

Effect of electron beam irradiation on (waste tire dust)‐filled ethylene vinyl acetate in the presence of bisphenol a diglycidyl ether

The effect of bisphenol A diglycidyl ether (BADGE) and electron beam (EB) irradiation on the properties of waste tire dust (WTD) ‐filled ethylene vinyl acetate (EVA) has been studied. The EVA/WTD ratio was fixed to 80:20, whereas the BADGE concentration varied from 1 to 5 wt%. The samples were then irradiated using a 3.0‐MeV EB machine at 50 kGy to 200 kGy at increments of 50 kGy. All the samples were subjected to various mechanical, physical, and thermal tests. Prior to irradiation, the mechanical properties of the composites show a gradual decrease with increasing BADGE concentration. Such observation is attributed to the plasticizing effect of the BADGE, as indicated by the reduction in mixing torque and a 14% increase in the elongation at break with the addition of 5 wt% BADGE. Results of gel fraction indicated that BADGE did not accelerate the irradiation‐induced crosslinking of EVA/WTD composites. The scanning electron micrographs and tan δ curves of EVA/WTD composites showed evidence that the addition of BADGE and EB irradiation of the EVA/WTD improves the compatibility of the composite. The overall results revealed that the irradiated EVA/WTD composite without BADGE gives a better enhancement in mechanical properties compared with the composites incorporated with the BADGE. J. VINYL ADDIT. TECHNOL., 23:172–180, 2017. © 2015 Society of Plastics Engineers     

Influence of Electron Beam Irradiation on High‐Temperature Mechanical Properties of Ethylene Vinyl Acetate/Carbon Fibers Composites

The purpose of this study was to investigate the effect of carbon fiber (CF) and electron‐beam (EB) radiation on high‐temperature mechanical properties of ethylene‐vinyl acetate (EVA). Polymer composites were prepared by mixing on a two‐roll mill. After compression molding, the samples were irradiated between 60 and 180 kGy, and dynamic mechanical analysis (DMA) was used to characterize physical properties. The effects of filler content and radiation level on the mechanical properties of EVA/CF were evaluated. The shear stress and modulus were observed to increase with increasing of the filler level. However, there was a dramatic decrease in creep compliance. It was also shown that introduction of irradiation on EVA composite increases the shear stress and the real part of the dynamic shear modulus G' due to the increase in molecular weight and cross‐linking of the polymer after irradiation. J. VINYL ADDIT. TECHNOL., 26:325–335, 2020. © 2019 Society of Plastics Engineers     

Effect of ambient‐temperature and high‐temperature electron‐beam radiation on the structural,thermal, mechanical,and dynamic mechanical properties of injection‐molded polyamide‐6,6

Electron‐beam irradiation of injection‐molded specimens of polyiminohexamethyleneiminoadipoyl (better known as polyamide‐6,6) was carried out in air at ambient temperature (303 K) and a high temperature (393 K). Most of the irradiated specimens were tensile dumbbells, although a few were cylinders for compressive stress relaxation testing. A few representative samples were dipped in triallyl cyanurate (TAC) solution before ambient‐temperature irradiation. The gel content of the specimens increased with radiation dose and the temperature of irradiation. Moreover, the TAC‐treated specimens showed an increase in gel content over the neat specimens irradiated at the same dose levels. Wide‐angle X‐ray scattering and differential scanning calorimetry studies revealed that the crystallinity decreased with increasing radiation dose. Irradiation at the high temperature and treatment with TAC further decreased the crystallinity compared to irradiation at ambient temperature. As determined from compressive stress relaxation and mechanical and dynamic mechanical properties, the optimized radiation dose for ambient‐temperature radiation was 200 kGy. The gels had a stiffening effect, and the rate of relaxation decreased significantly. The water‐uptake characteristics of the tensile specimens were investigated; this revealed a decrease in the water absorption tendency with increasing gel content. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 99: 1633–1644, 2006     

辐射交联LDPE/EVA混合体系泡沫片材性能的研究

辐射交联LDPE/EVA混合体系泡沫片材表观光滑、柔软,手感好,表观密度较小,材料具有优异的力学性能,较高的拉伸强度、断裂伸长率和撕裂强度。进一步研究了产生宏观性能差异的原因是辐射交联LDPE/EVA混合体系泡沫片材制备成型工艺的特殊性,体系的交联度对制品性能影响很大。通过凝胶分析知道交联度与辐照剂量、LDPE树脂的物理性能和EVA树脂在混合体系的含量有关。此外,LDPE树脂的物理性能和EVA在混合体系的含量对材料宏观性能也有影响。     

Photocrosslinking of halogen‐free flame‐retarded ethylene‐vinyl acetate copolymer by phosphorous‐nitrogen compound NP28

The photoinitiated crosslinking of halogen‐free flame‐retarded ethylene‐vinyl acetate copolymer (EVA) by the phosphorous‐nitrogen compound NP28 in the presence of photoinitiator and crosslinker and characterization of the related properties have been investigated by gel determination, heat extension test, thermogravimetric analysis (TGA), mechanical measurement, and thermal aging test. The photocrosslinking efficiency of EVA/NP28 blend and various factors affecting the crosslinking process, such as photoinitiator, crosslinker, NP28 content, and irradiation temperature, were studied in detail and optimized by comparison of gel content. The results show that the EVA/NP28 blend filled with 28.2 wt % NP28 with a thickness of 1.6 mm is homogeneously photocrosslinked to a gel content of above 80 wt % with 4.8 s UV‐irradiation under optimum conditions. The data from TGA, mechanical measurement, and thermal aging test give evidence that the thermal stability and mechanical properties of photocrosslinked EVA/NP28 blend are much better than those of the unphotocrosslinked one.© 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Effects of peroxide crosslinking on the mechanical and morphological properties of poly(ethylene‐co‐vinyl acetate)/zeolite composites

Uncrosslinked and chemically crosslinked ethylene‐vinyl acetate copolymers (EVAs) with 5–25 volume percentages of zeolite were prepared in a melt‐mixing process and then compression‐molded on a hot‐press machine according to standard test specifications. The mechanical properties measured by tensile test showed a reduction in tensile strength and elongation at break with increasing zeolite content. However, an increasing trend was observed for tensile modulus with addition of zeolite. Experimental results for ultimate stress were compared with those from Pukanszky equation. The experimental data showed a good fit to the Pukanszky model. The improvement in the interfacial interaction for crosslinked composites was also confirmed by this model. Morphological changes of EVA/zeolite composites were analyzed by scanning electron microscopy (SEM). The fractured surface of the composites indicated more complex morphology at higher zeolite loading. The influence of crosslinking induced by 2 wt% of dicumyl peroxide on the properties of EVA/zeolite composites was also investigated. The crosslinked composites showed better tensile properties than the uncrosslinked ones, a result which might be an indication of enhanced interaction between the EVA and zeolite. Density measurements, gel content determinations, and Fourier transform infrared analyses were also performed to evaluate the crosslink content of the composites. The changes in the properties of chemically crosslinked EVA/zeolite composites were observed. Meanwhile, SEM micrographs of the crosslinked EVA/zeolite composites showed better interfacial strength between zeolite and the EVA matrix as compared to that of the uncrosslinked composites. J. VINYL ADDIT. TECHNOL., 2012. © 2012 Society of Plastics Engineers     

Effect of the electron beam irradiation on the properties of epoxidized natural rubber (ENR 50) compatibilized linear low‐density polyethylene/soya powder blends

Linear low‐density polyethylene/soya powder blends were prepared by using an internal mixer at 150°C. The soya powder content ranged from 5 to 40 wt %. Epoxidized natural rubber with 50 mol % epoxidation (ENR 50) was added as a compatibilizer. The blends were irradiated by electron beam (EB) at a constant dose of 30 kGy. The changes in gel fraction, tensile properties, morphological and thermal properties of the samples were investigated. The gel content increased after EB irradiation. However, the increment of gel content was hindered by increasing soya powder content. The tensile strength and Young's modulus of the blends were increased by EB whereas the elongation at break decreased. The tensile fracture surface also support the reduction of elongation at break by EB irradiation. Further analysis on the irradiated blends using Fourier transform infrared spectra indicated an increase of oxygenated product after undergoing EB irradiation. The differential scanning calorimetry result indicated that the melting temperature of the blends decreased after EB irradiation whereas the crystallinity increased. EB irradiation also enhanced the thermal stability of the blends as indicated by thermogravimetric analysis. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Effect of electron beam irradiation on the properties of ethylene‐(vinyl acetate) copolymer/natural rubber/organoclay nanocomposites

The effects of electron beam (EB) irradiation on the morphology, crosslink density, and tensile properties of EVA/SMR L (Standard Malaysian Rubber)/organoclay nanocomposites prepared by a melt‐blending technique were investigated. All the samples were irradiated by using a 3.0‐MeV EB apparatus with doses ranging from 50 to 200 kGy. Organoclay loading was varied from 0 to 10 phr (parts by weight per hundred parts of resin). X‐ray diffraction results and transmission electron microscopy images proved that the dispersion of organoclay in the nanocomposites was slightly improved by EB irradiation. The gel fraction yield for the nanocomposites increased with irradiation dose but decreased with organoclay loading. However, at 200 kGy, the gel fraction yield was almost the same at all organoclay loadings. Tensile strength and stress at 100% elongation increased proportionally with the irradiation dose. Elongation at break of the nanocomposites increased up to 100 kGy but then decreased at higher irradiation doses. The intercalation and exfoliation of the organoclay, the barrier effect, and the Hofmann degradation of the modification agent are the three major factors leading to the improvement of the properties of the irradiated nanocomposites. J. VINYL ADDIT. TECHNOL., 2009. © 2009 Society of Plastics Engineers