Increasing the efficiency of a diesel engine running on biodiesel through butanol fumigation

A single-cylinder, direct-injection diesel engine was tested with regular diesel oil, neat Jatropha biodiesel, and biodiesel with butanol injection into the inlet manifold. An engine fueled with neat biodiesel showed 5% reduction of the fuel conversion efficiency and 17% increase in specific fuel consumption relative to diesel oil. With butanol injection at a rate of 25% of the total fuel consumption, the efficiency was equivalent to that of diesel oil and specific fuel consumption was less than that of neat biodiesel. Engine emissions with biofuel were improved except for carbon monoxide and unburned hydrocarbons. It was concluded that the diesel engine can operate on the neat biofuel (biodiesel plus alcohol) with the fuel conversion efficiency equivalent to that of the diesel oil.     

Synergistic effect of hydrogen induction with biofuel obtained from winery waste (grapeseed oil) for CI engine application

The purpose of this study is to experimentally investigate the use of grapeseed oil as a fuel substitute obtained from biomass waste from winery industry and the synergic effect of hydrogen addition for compression ignition engine application. The experiments were carried out in a single cylinder, four stroke diesel engine for various loads and energy share of hydrogen. Combustion, performance and emission characteristics of grapeseed biodiesel, neat grapeseed oil and diesel have been analysed and compared with the results obtained with hydrogen induction in the intake manifold in dual fuel mode. At full load, maximum brake thermal efficiency of the engine with diesel, grapeseed biodiesel and neat grapeseed oil has increased from 32.34%, 30.28% and 25.94% to 36.04%, 33.97% and 30.95% for a maximum hydrogen energy share of 14.46%, 14.1% and 12.8% respectively. Although there is an increasing trend in Nitric Oxide emission with hydrogen induction, smoke, brake specific hydrocarbon, carbon monoxide, and carbon dioxide emissions respectively, reduces. Nitric oxide emission of Grapeseed biodiesel with maximum hydrogen share at full load is higher by 43.61% and smoke emission lower by 19.73% compared to biodiesel operation without hydrogen induction.     

Effect of diethyl ether additive in Jatropha biodiesel-diesel fuel blends on the variable compression ratio diesel engine performance and emissions characteristics at different loads and compression ratios

An investigational analysis was performed to assess the effect of diethyl ether (DEE) that acts as an oxygenated additive in Jatropha biodiesel and diesel fuel blends on the performance enhancement and emission reduction of a variable compression ratio (CR) diesel engine. The DEE (10% vol) is added to different concentration levels of Jatropha biodiesel (B5, B10, and B20). The Jatropha biodiesel (JME) is prepared by the transesterification reaction and DEE is prepared through acid distillation of ethanol. The various tests were conducted by varying the loads at 25%, 50%, 75%, and 100% (3, 6, 9, and 12 kg). The DEE was entirely miscible with diesel and Jatropha biodiesel, the addition of DEE increases the cetane and calorific value, kinematic viscosity of the fuel blends compared with neat diesel or Jatropha biodiesel. The results illustrate that at higher loads and CRs, the engine performance parameters such as brake thermal efficiency enhances and reduces the brake-specific fuel consumption for DEE-Jatropha biodiesel-diesel fuel blends. Blend A3 (10% DEE + 20% JME + 70% diesel) demonstrated an overall improvement in the engine performance parameters and emission characteristics compared with A1, A2, and diesel fuel blends. It is concluded that the DEE-JME-diesel fuel blend is a promising source of fuel for diesel engine at maximum load.     

Effect of induction on exhaust gas recirculation and hydrogen gas in compression ignition engine with simarouba oil in dual fuel mode

Biofuels extracted from non-edible oil is sustainable and can be used as an alternative fuel for internal combustion engines. This study presents the performance, emission and combustion characteristic analysis by using simarouba oil (obtained from Simarouba seed) as an alternative fuel along with hydrogen and exhaust gas recirculation (EGR) in a compression ignition (CI) engine operating on dual fuel mode. Simarouba biofuel blend (B20) was prepared on volumetric basis by mixing simarouba oil and diesel in the proportion of 20% and 80% (v/v), respectively. Hydrogen gas was introduced at the flow rate of 2.67 kg/min, and EGR concentration was maintained at 30% of total air introduction. Performance, combustion and emission characteristics analysis were examined with biodiesel (B20), biodiesel with hydrogen substitution and biodiesel, hydrogen with EGR and were compared with neat diesel operation. Results indicate that BTE of the engine operating with biodiesel B20 was decreased when compared to neat diesel operation. However, introducing hydrogen along with B20 blend into the combustion chamber shows a slight increase in the BTE by 1%. NO_x emission was increased to 18.13% with the introduction of hydrogen than that of base fuel (diesel) operation. With the introduction of EGR, there is a significant reduction in NO_x emission due to decrease in in-cylinder temperature by 19.07%. A significant reduction in CO, CO_2, and smoke emissions were also noted with the introduction of both hydrogen and EGR. The ignition delay and combustion duration were increased with the introduction of hydrogen, EGR with biodiesel than neat diesel operation. Hence, the proposed biodiesel B20 with H₂ and EGR combination can be applied as an alternative fuel in CI engines.     

The effect of biodiesel oxidation on engine performance and emissions

Biodiesel is an alternative fuel consisting of the alkyl monoesters of fatty acids from vegetable oils or animal fats. Previous research has shown that biodiesel-fueled engines produce less carbon monoxide, unburned hydrocarbons, and particulate emissions compared to diesel fuel. One drawback of biodiesel is that it is more prone to oxidation than petroleum-based diesel fuel. In its advanced stages, this oxidation can cause the fuel to become acidic and to form insoluble gums and sediments that can plug fuel filters. The objective of this study was to evaluate the impact of oxidized biodiesel on engine performance and emissions. A John Deere 4276T turbocharged DI diesel engine was fueled with oxidized and unoxidized biodiesel and the performance and emissions were compared with No. 2 diesel fuel. The neat biodiesels, 20% blends, and the base fuel (No. 2 diesel) were tested at two different loads (100 and 20%) and three injection timings (3° advanced, standard; 3° retarded). The tests were performed at steady-state conditions at a single engine speed of 1400 rpm. The engine performance of the neat biodiesels and their blends was similar to that of No. 2 diesel fuel with the same thermal efficiency, but higher fuel consumption. Compared with unoxidized biodiesel, oxidized neat biodiesel produced 15 and 16% lower exhaust carbon monoxide and hydrocarbons, respectively. No statistically significant difference was found between the oxides of nitrogen and smoke emissions from oxidized and unoxidized biodiesel.     

A study on the performance and emission of a diesel engine fueled with Jatropha biodiesel oil and its blends

Biodiesel either in neat form or as a mixture with diesel fuel is widely investigated to solve the twin problem of depletion of fossil fuels and environmental degradation. The main objective of the present study is to compare performance, emission and combustion characteristics of biodiesel derived from non edible Jatropha oil in a dual fuel diesel engine with base line results of diesel fuel. The performance parameters evaluated were: brake thermal efficiency, brake specific fuel consumption, power output. As a part of combustion study, in-cylinder pressure, rate of pressure rise and heat release rates were evaluated. The emission parameters such as carbon monoxide, carbon dioxide, un-burnt hydrocarbon, oxides of nitrogen and smoke opacity with the different fuels were also measured and compared with base line results. The different properties of Jatropha oil after transestrification were within acceptable limits of standards as set by many countries. The brake thermal efficiency of Jatropha methyl ester and its blends with diesel were lower than diesel and brake specific energy consumption was found to be higher. However, HC, CO and CO₂ and smoke were found to be lower with Jatropha biodiesel fuel. NO_x emissions on Jatropha biodiesel and its blend were higher than Diesel. The results from the experiments suggest that biodiesel derived from non edible oil like Jatropha could be a good substitute to diesel fuel in diesel engine in the near future as far as decentralized energy production is concerned. In view of comparable engine performance and reduction in most of the engine emissions, it can be concluded and biodiesel derived from Jatropha and its blends could be used in a conventional diesel engine without any modification.     

Emission analysis of Botryococcus braunii algal biofuel using Ni-Doped ZnO nano additives for IC engines

Microalgae biodiesel has been considered ?as a clean renewable fuel for diesel marine engines. This is due to its optimistic characterizations such as ?rapid growth rate, high productivity, and its ability to convert CO₂ into fuel. In this study, the use of microalgae biodiesel, obtained from Botryococcus braunii, as an alternative fuel for diesel marine engines has been investigated. The diesel engine is verified experimentally using Ni-Doped ZnO nano additive blends with algae biodiesel and neat diesel fuel. The results showed that doped nano additive blends? produce less emission compared to B20.     

Evaluating combustion,performance and emission characteristics of diesel engine using karanja oil methyl ester biodiesel blends enriched with HHO gas

With a specific end goal to take care of the worldwide demand for energy, a broad research is done to create alternative and cost effective fuel. The fundamental goal of this examination is to investigate the combustion, performance and emission characteristics of diesel engine using biodiesel blends enriched with HHO gas. The biodiesel blends are gotten by blending KOME obtained from transesterification of karanja oil in various proportions with neat diesel. The HHO gas is produced by the electrolysis of water in the presence of sodium bicarbonate electrolyte. The constant flow of HHO gas accompanied with biodiesel guarantees lessened brake specific fuel consumption by 2.41% at no load and 17.53% at full load with increased the brake thermal efficiency by 2.61% at no load and 21.67% at full load contrasted with neat diesel operation. Noteworthy decline in unburned hydrocarbon, carbon monoxide, carbon-dioxide emissions and particulate matter with the exception of NO_x discharge is encountered. The addition of EGR controls this hike in NO_x with a slight decline in the performance characteristics. It is clear that the addition of HHO gas with biodiesel blends along with EGR in the test engine improved the overall characterization of engine.     

发动机燃用生物柴油的性能研究

通过对比研究了柴油机燃用餐饮废弃油炼制的生物柴油、柴油及B50时在高原地区的动力性、经济性及排放特性。研究结果表明：在柴油机不进行任何调整的情况下,全负荷时,燃用生物柴油的发动机动力性降低6.8%,B50降低3%;燃用生物柴油有效燃油消耗率升高了13.8%;燃用B50在高速高负荷时柴油机热效率提高2.5%;无论在全负荷还是在部分负荷工况下,燃用生物柴油均能大幅度降低柴油机烟度、CO和HC排放,但会引起NOx排放量的上升。     

Effects of oxyhydrogen on the CI engine fueled with the biodiesel blends: A performance,combustion and emission characteristics study

The main purpose of this study is to analyse the effects of oxy hydrogen (HHO) along with the Moringa oleifera biodiesel blend on engine performance, combustion and emission characteristics. HHO gases were generated using the typical electrolysis process using the potassium hydroxide solution. The experiments were performed under various engine loads of 25%, 50%, 75%, and 100% in a constant speed engine. Biodiesel from the M. oleifera was prepared by the transesterification process. Further, the procured biodiesel blends mixed with neat diesel at the concentration of 20% (B20) and 40% (B40). In addition to above, the HHO gas flow rate to the engine chamber maintained at the flow rate of 0.5 L^-1. The use of the 20% and 40% blends with HHO reported less BTE compared to the neat diesel. However, B20 reported marginal rise in the BTE due to the addition of the HHO gas. On the other hand, addition of HHO gas to the blends significantly dropped the brake specific fuel consumption. With regard to the emissions, addition of the biodiesel blends reduced the concentration of the CO, HC, and CO₂. Nevertheless, no reduction reported in the formation of the NO. However, adding the HHO to the biodiesel reduced the average NOx by 6%, which is a substantial effect. Overall, HHO enriching biodiesel blends are the potential replacement for the existing fossil fuels for its superior fuel properties compared to the conventional diesel.     

The effects of turbocharger on the performance and exhaust emissions of a diesel engine fuelled with biodiesel

This paper investigates the effects of turbocharger on the performance of a diesel engine using diesel fuel and biodiesel in terms of brake power, torque, brake specific consumption and thermal efficiency, as well as CO and NO_x emissions. For this aim, a naturally aspirated four-stroke direct injection diesel engine was tested with diesel fuel and neat biodiesel, which is rapeseed oil methyl ester, at full load conditions at the speeds between 1200 and 2400 rpm with intervals of 200 rpm. Then, a turbocharger system was installed on the engine and the tests were repeated for both fuel cases. The evaluation of experimental data showed that the brake thermal efficiency of biodiesel was slightly higher than that of diesel fuel in both naturally aspirated and turbocharged conditions, while biodiesel yielded slightly lower brake power and torque along with higher fuel consumption values. It was also observed that emissions of CO in the operations with biodiesel were lower than those in the operations with diesel fuel, whereas NO_x emission in biodiesel operation was higher. This study reveals that the use of biodiesel improves the performance parameters and decreases CO emissions of the turbocharged engine compared to diesel fuel.     

Environment effect of La2O3 nano-additives on microalgae-biodiesel fueled CRDI engine with conventional diesel

In this present work, corn oil biodiesel with La₂O₃ was used as an additive with neat diesel fuel and blends were prepared. La₂O₃ nanoparticles are dispersed in the emulsions with different dosage levels of 50, 75, and 100 ppm. A single-cylinder, four-stroke CRDI diesel engine is made to run on different fuel concentrations to study the effect of emission characteristics of the fuel. The test engine was operated under constant engine speed (1500 rpm) and different engine load test conditions. According to the experimental results, fuel blends with biodiesel fuel emission increases CO₂ and NOx and reduces the CO, HC, and smoke emissions compared with the B20 fuel.     

Influence of biodiesel on engine combustion and emission characteristics

This paper discusses the influence of biodiesel on the engine combustion characteristics. The considered fuel is neat biodiesel from rapeseed oil. The considered engine is a bus diesel engine with injection M system. The engine characteristics are obtained by experiments and numerical simulation. The results obtained with biodiesel are compared to those obtained with mineral diesel under various operating regimes. In this way, the influences of biodiesel usage on the injection pressure, injection timing, ignition delay, in-cylinder gas pressure and temperature, heat release rate, exhaust gas temperatures, harmful emissions, specific fuel consumption, and on engine power are analyzed. Furthermore, the relationships among fuel properties, injection and combustion characteristics, harmful emissions, and other engine performance are determined. Special attention is given to possible explanations of higher NO_x emission in spite of lower in-cylinder gas temperature.     

Effect of nanoparticle on emission and performance characteristics of a diesel engine fueled with cashew nut shell biodiesel

High-rise in the air pollution levels due to combustion of the fossil fuel gives us the opportunity to discover environmentally friendly and clean fuels for the engines. Biodiesel originated from cashew nut shell oil through transesterification process can be blended or used as a neat fuel in unmodified engines. This work investigates the effect of alumina nanoparticles on emission and performance characteristics of cashew nut shell biodiesel. Neat cashew nut shell biodiesel prepared by conventional transesterification is termed as BD100 and biodiesel prepared by modified transesterification with the addition of alumina nanoparticles is termed as BD100A. Experimental results on unmodified diesel engine revealed that emission parameters such as CO, HC, NOx, and smoke were decreased by 5.3%, 7.4%, 10.23%, and 16.1% for BD100% and 8.8%, 10.1%, 12.4%, and 18.4% for B100A, respectively, compared to diesel fuel. At full load conditions, compared to diesel fuel, the BTE dropped by 1.1% and 2.3%, whereas the BSFC increased by 3.8% and 5.1% for B100A and B100 correspondingly.     

非直喷式增压柴油机燃用生物柴油的性能与排放特性

研究了非直喷式增压柴油机燃用柴油一生物柴油混合燃料的性能和排放特性。未对原机作任何调整和改动，研究了不同生物柴油掺混比例的混合燃料对功率、油耗、烟度和NOx排放的影响。结果表明：非直喷式柴油机燃用生物柴油后柴油机功率略有下降，油耗有所上升，烟度大幅下降，NOx排放增加明显。油耗、烟度和NOx的变化均与生物柴油掺混比例呈线性关系，合适的生物柴油掺混比例即可以保持柴油机的性能，又可有效地降低碳烟排放，且不引起NOx排放的显著变化。对于该增压柴油机，掺混生物柴油对外特性下的排放影响最大，影响最小的为标定转速下的负荷特性。不论是全负荷还是部分负荷，燃用生物柴油时低速下的烟度降低和NOx上升幅度均比高速时大，而同转速下高负荷时烟度降低和NOx上升更为明显。     

Experimental investigations on combustion, performance and emissions characteristics of neat karanji biodiesel and its methanol blend in a diesel engine

The increased focus on alternative fuels research in the recent years are mainly driven by escalating crude oil prices, stringent emission norms and the concern on clean environment. The processed form of vegetable oil (biodiesel) has emerged as a potential substitute for diesel fuel on account of its renewable source and lesser emissions. The experimental work reported here has been carried out on a turbocharged, direct injection, multi-cylinder truck diesel engine fitted with mechanical distributor type fuel injection pump using biodiesel-methanol blend and neat karanji oil derived biodiesel under constant speed and varying load conditions without altering injection timings. The results of the experimental investigation indicate that the ignition delay for biodiesel-methanol blend is slightly higher as compared to neat biodiesel and the maximum increase is limited to 1 deg. CA. The maximum rate of pressure rise follow a trend of the ignition delay variations at these operating conditions. However, the peak cylinder pressure and peak energy release rate decreases for biodiesel-methanol blend. In general, a delayed start of combustion and lower combustion duration are observed for biodiesel-methanol blend compared to neat biodiesel fuel. A maximum thermal efficiency increase of 4.2% due to 10% methanol addition in the biodiesel is seen at 80% load and 16.67 s⁻¹ engine speed. The unburnt hydrocarbon and carbon monoxide emissions are slightly higher for the methanol blend compared to neat biodiesel at low load conditions whereas at higher load conditions unburnt hydrocarbon emissions are comparable for the two fuels and carbon monoxide emissions decrease significantly for the methanol blend. A significant reduction in nitric oxide and smoke emissions are observed with the biodiesel-methanol blend investigated.     

Performance and emission study on the effect of oxygenated additive in neat biodiesel fueled diesel engine

This work presents the effect of the Di-tetra-butyl-peroxide (DTBP) as an oxygenated additive on neat used mustard oil biodiesel (B100) to evaluate the emission and performance engine characteristics. Four fuels, namely, diesel, biodiesel (Mustard biodiesel), a blend of B100-10percentage, and 20% by volume of DTBP (BD90DTBP10 and BD80DTBP20) are prepared and tested on a single cylinder, constant speed diesel engine. Experimental outcomes revealed that 20% of DTBP reduces 7.3% CO, 5.1% HC, and 4.6% NOx and 3.2% smoke emissions of B100. From this study, further, it is inferred that BD80DTBP20 blend could be utilized as an alternative fuel for a CI engine with no modifications in engine design.     

Biodiesel fuel in diesel micro-turbine engines: Modelling and experimental evaluation

Many performance and emission tests have been carried out in reciprocating diesel engines that use biodiesel fuel over the past years and very few in gas turbine engines. This work aims at assessing the thermal performance and emissions at full and partial loads of a 30 kW diesel micro-turbine engine fed with diesel, biodiesel and their blends as fuel. A cycle simulation was performed using the Gate Cycle GE Enter software to evaluate the thermal performance of the 30 kW micro-turbine engine. Performance and emission tests were carried out on a 30 kW diesel micro-turbine engine installed in the NEST laboratories of the Federal University of Itajubá, and the performance results were compared with those of the simulation. There was a good agreement between the simulations and the experimental results from the full load down to about 50% of the load for diesel, biodiesel and their blends. The biodiesel and its blends used as fuel in micro-turbines led to no significant changes in the engine performance and behaviour compared to diesel fuel. The exhaust emissions were evaluated for pure biodiesel and its blends and conventional diesel. The results revealed that the use of biodiesel resulted in a slightly higher CO, lower NO_x and no SO₂ emissions.     

Hydrogen-enriched palm biodiesel as a potential alternative fuel for diesel engines: Investigating performance and emission characteristics and mitigation strategies for air pollutants

Palm biodiesel is one of the most suitable alternative fuels due to its capability to replace traditional fossil fuel usage in IC engines. Even as palm biodiesel (POBD) reduces harmful pollutant gases, the engine performance is not on an equal scale with neat diesel. To address this shortcoming, an investigation was carried out to examine the application of palm biodiesel (PBD) and hydrogen induction through the intake air at the flow rates of 6 and 8LPM (Litre Per Minute) in the compression ignition (CI) engine. The experimental study shows that POBD has poor engine performance and moderate pollution reduction compared with neat diesel. When compared to POBD and neat diesel, the higher calorific value and other H₂ characteristics improve combustion properties, resulting in higher engine performance and lower pollutant gases (except NOx). When compared to the palm biodiesel blend (BD 30), the results of BD30+8LPM reduced the Specific fuel consumption (SFC) by 0.0885kg/kWh and improved the brake thermal efficiency (BTE) by 6.67%. The Carbon monoxide (CO), hydro carbon (HC), and smoke opacity were reduced by 0.047% volume, 29.2 ppm, and 6.52% respectively. A marginal increase in NOx was seen as 297.6 ppm.     

Biodiesel from cotton seed oil and its effect on engine performance and exhaust emissions

The use of biodiesel is rapidly expanding around the world, making it imperative to fully understand the impacts of biodiesel on the diesel engine combustion process and pollutant formation. Biodiesel is known as the mono-alkyl-esters of long chain fatty acids derived from renewable feedstocks, such as, vegetable oils or animal fats, for use in compression ignition engines. Different parameters for the optimization of biodiesel production were investigated in the first phase of this study, while in the next phase of the study performance test of a diesel engine with neat diesel fuel and biodiesel mixtures were carried out. Biodiesel was made by the well known transesterification process. Cottonseed oil (CSO) was selected for biodiesel production. Cottonseed is non-edible oil, thus food versus fuel conflict will not arise if this is used for biodiesel production. The transesterification results showed that with the variation of catalyst, methanol or ethanol, variation of biodiesel production was realized. However, the optimum conditions for biodiesel production are suggested in this paper. A maximum of 77% biodiesel was produced with 20% methanol in presence of 0.5% sodium hydroxide. The engine experimental results showed that exhaust emissions including carbon monoxide (CO) particulate matter (PM) and smoke emissions were reduced for all biodiesel mixtures. However, a slight increase in oxides of nitrogen (NO_x) emission was experienced for biodiesel mixtures.