废气再循环在柴油机中的应用

本文回顾了废气再循环（EGR）在减少排放，特别是减少NOx排放上的潜力以及限定这一技术的应用范围。详细分析了RGR装置对柴油机的排放和性能的影响，通过深入分析，发现在柴油机进气中引入废气再循环（EGR），相当如置换了部分吸入的空气，这种方式能充分减少NOx的排放。因此，废气再循环的使用是最有效改善尾气排放的技术措施之一。     

The effect of biodiesel and bioethanol blended diesel fuel on nanoparticles and exhaust emissions from CRDI diesel engine

Biofuel (biodiesel, bioethanol) is considered one of the most promising alternative fuels to petrol fuels. The objective of the work is to study the characteristics of the particle size distribution, the reaction characteristics of nanoparticles on the catalyst, and the exhaust emission characteristics when a common rail direct injection (CRDI) diesel engine is run on biofuel-blended diesel fuels. In this study, the engine performance, emission characteristics, and particle size distribution of a CRDI diesel engine that was equipped with a warm-up catalytic converters (WCC) or a catalyzed particulate filter (CPF) were examined in an ECE (Economic Commission Europe) R49 test and a European stationary cycle (ESC) test. The engine performance under a biofuel-blended diesel fuel was similar to that under D100 fuel, and the high fuel consumption was due to the lowered calorific value that ensued from mixing with biofuels. The use of a biodiesel–diesel blend fuel reduced the total hydrocarbon (THC) and carbon monoxide (CO) emissions but increased nitrogen oxide (NO_x) emissions due to the increased oxygen content in the fuel. The smoke emission was reduced by 50% with the use of the bioethanol–diesel blend. Emission conversion efficiencies in the WCC and CPF under biofuel-blended diesel fuels were similar to those under D100 fuel. The use of biofuel-blended diesel fuel reduced the total number of particles emitted from the engine; however, the use of biodiesel–diesel blends resulted in more emissions of particles that were smaller than 50 nm, when compared with the use of D100. The use of a mixed fuel of biodiesel and bioethanol (BD15E5) was much more effective for the reduction of the particle number and particle mass, when compared to the use of BD20 fuel.     

Impact of exhaust gas recirculation (EGR) on the oxidative reactivity of diesel engine soot

This paper expands the consideration of the factors affecting the nanostructure and oxidative reactivity of diesel soot to include the impact of exhaust gas recirculation (EGR). Past work showed that soot derived from oxygenated fuels such as biodiesel carries some surface oxygen functionality and thereby possesses higher reactivity than soot from conventional diesel fuel. In this work, results show that EGR exerts a strong influence on the physical properties of the soot which leads to enhanced oxidation rate. HRTEM images showed a dramatic difference between the burning modes of the soot generated under 0 and 20% EGR. The soot produced under 0% EGR strictly followed an external burning mode with no evidence of internal burning. In contrast, soot generated under 20% EGR exhibited dual burning modes: slow external burning and rapid internal burning. The results demonstrate clearly that highly reactive soot can be achieved by manipulating the physical properties of the soot via EGR.     

The effect of HRG gas addition on diesel engine combustion characteristics and exhaust emissions

Extensive studies have been dedicated in the last decade to the possibility to use hydrogen in the dual-fuel mode to improve combustion characteristics and emissions of a diesel engine. The results of these studies, using pure hydrogen or hydrogen containing gas produced through water electrolysis, are notably different.The present investigation was conducted on a tractor diesel engine running with small amounts of the gas—provided by a water electrolyzer—aspirated in the air stream inducted in the cylinder. The engine was operated at light and medium loads and various speeds.It was found that the addition of HRG gas has a slight negative impact, up to 2%, on the engine brake thermal efficiency. Smoke is significantly reduced, up to 30%, with HRG enrichment, while NO_x concentrations vary in both senses, up to 14%, depending on the engine operation mode. A relative small amount of HRG gas can be used with favorable effects on emissions and with a small penalty in thermal efficiency.     

Experimental study of engine performance and emissions for hydrogen diesel dual fuel engine with exhaust gas recirculation

With an alarming enlargement in vehicular density, there is a threat to the environment due to toxic emissions and depleting fossil fuel reserves across the globe. This has led to the perpetual exploration of clean energy resources to establish sustainable transportation. Researchers are continuously looking for the fuels with clean emission without compromising much on vehicular performance characteristics which has already been set by efficient diesel engines. Hydrogen seems to be a promising alternative fuel for its clean combustion, recyclability and enhanced engine performance. However, problems like high NOx emissions is seen as an exclusive threat to hydrogen fuelled engines. Exhaust gas recirculation (EGR), on the other hand, is known to overcome the aforementioned problem. Therefore, this study is conducted to study the combined effect of hydrogen addition and EGR on the dual fuelled compression ignition engine on a single cylinder diesel engine modified to incorporate manifold hydrogen injection and controlled EGR. The experiments are conducted for 25%, 50%, 75% and 100% loads with the hydrogen energy share (HES) of 0%, 10% and 30%. The EGR rate is controlled between 0%, 5% and 10%. With no substantial decrement in engine's brake thermal efficiency, high gains in terms of emissions are observed due to synergy between hydrogen addition and EGR. The cumulative reduction of 38.4%, 27.4%, 33.4%, 32.3% and 20% with 30% HES and 10% EGR is observed for NOx, CO2, CO, THC and PM, respectively. Hence, the combination of hydrogen addition and EGR is observed to be advantageous for overall emission reduction.     

Effect of exhaust gas recirculation (EGR) temperature for various EGR rates on heavy duty DI diesel engine performance and emissions

DI diesel engines are well established today as the main powertrain solution for trucks and other relevant heavy duty vehicles. At the same time emission legislation (mainly for NO_x and particulate matter) becomes stricter, reducing their limit to extremely low values. One efficient method to control NO_x in order to achieve future emissions limits is the use of rather high exhaust gas recirculation (EGR) rates accompanied by increased boost pressure to avoid the negative impact on soot emissions. The method is based on the reduction of gas temperature level and O₂ availability inside the combustion chamber, but unfortunately it has usually an adverse effect on soot emissions and brake specific fuel consumption (bsfc). The use of high EGR rates creates the need for EGR gas cooling in order to minimize its negative impact on soot emissions especially at high engine load were the EGR flow rate and exhaust temperature are high. For this reason in the present paper it is examined, using a multi-zone combustion model, the effect of cooled EGR gas temperature level for various EGR percentages on performance and emissions of a turbocharged DI heavy duty diesel engine operating at full load. Results reveal that the decrease of EGR gas temperature has a positive effect on bsfc, soot (lower values) while it has only a small positive effect on NO. As revealed, the effect of low EGR temperature is stronger at high EGR rates.     

Performance and emission characteristics of a diesel engine with Diesel Premixed Compression Ignition and exhaust gas recirculation

In the present work, diesel was used as a premixed fuel along with the conventional injection of diesel with a premixed ratio of 0.25. The premixed charge was burned in the cylinder along with the fuel directly injected into the cylinder by a conventional injection system. To control nitrogen oxide(s) (NO_x) emissions, Exhaust Gas Recirculation (EGR) was adopted and the exhaust gas was varied from 10% to 30% in steps of 10%. The performance and emission characteristics were compared with conventional 100% diesel injection in the main chamber. Based on the experiments conducted on a Compression Ignition Direct Injection (CIDI) engine, it was found that unburnt hydrocarbons, carbon monoxide, and soot emissions increase. Soot emission decreases with up to 20% EGR and increases when EGR was increased beyond 20%. Hence 20% EGR was found to be the optimum use for DPMCI mode with a premixed ratio of 0.25. Due to the lean operation, significant reduction in NO_x was achieved with the DPMCI combustion mode. Brake thermal efficiency was marginally decreased compared to CIDI mode.     

Particle-bound PAH emissions from a waste glycerine-derived fuel blend in a typical automotive diesel engine

Polynuclear or polycyclic aromatic hydrocarbons (PAH) are known to be one of the most dangerous types of compounds of their class due to their carcinogenic potential. Some atmospheric PAH are measured and regulated to quantify the air quality. However, in order to better understand the presence of these compounds in the atmosphere it is crucial to study the PAH emissions sources. In this work, we analyze the particulate-bound PAH emissions, as well as their carcinogenic potential, from a typical baseline diesel engine using a promising alternative fuel obtained from the glycerol surplus in the biodiesel production industry. This advanced biofuel (Mo.bio) is a ternary mixture of residual glycerine-derived fuel (FAGE), a conventional fatty acid methyl ester (FAME) and a diesel fuel. Two operating conditions representative of the conflicting scenarios when studying polluting emissions (speeds of 50 km/h and 70 km/h typical of urban and extra-urban driving conditions) are used. In addition, with the purpose of deepening the understanding of the behavior of this new fuel, tests are carried out modifying the Exhaust Gas Recirculation (EGR) ratio. The PAH samples are collected before the aftertreatment systems in order to assess the possible formation of PAH with this type of fuel and to evaluate the options of the aftertreatment devices. Sampling is carried out using fiber-glass filters, extracting the trapped PAH using Soxhlet method. The analytical procedure (liquid chromatography with fluorescence detection) allows to appreciate differences between the different fuels and modes of operation, observing higher emissions of benzo[a]pyrene (BaP) and dibenz[a,h]anthracene (DahA) for the diesel fuel than for the mixture containing residual glycerine-derived fuel. Therefore, it is concluded that the fossil fuel has a larger carcinogenic potential in these conditions, and that the Mo.Bio fuel may possibly expand the EGR ratio range without increasing the requirement of the particle filter.     

Investigating the effects of injection and induction modes of hydrogen addition in a CRDI pilot diesel-fuel engine with exhaust gas recirculation

This work compares the outcomes of different flow rates of hydrogen added by induction and injection methods in three different flow rates (3, 9, and 15 LPM) through the intake manifold of a constant speed CRDI diesel engine operated at 1500 rpm. The premixed air and hydrogen mixture was ignited by injecting diesel fuel at 23? bTDC. Hydrogen addition reduced CO, HC, and smoke in both the techniques, but efficiency was decreased at a higher percentage of hydrogen induction, whereas it increased with the injection technique. The higher calorific value and flame velocity helped proper combustion and improved brake thermal efficiency by 7%, and the brake-specific energy consumption was reduced by 10.7%. In addition, CO, UHC, and Smoke were decreased by 15.8, 29.7, and 15% compared with neat diesel at full BMEP. Nitrogen oxides decreased by 5.6% for 15 LPM of hydrogen injection compared to the induction method with the same flow rate but higher than diesel fuel by 35.9%. Three different EGR percentages (5, 7.5, and 10%) were used to reduce the higher NOx emission. Though the injection process was complex compared to the induction method, the injection process can provide promising results even at higher hydrogen flow rates.     

Experimental study of various effects of exhaust gas recirculation (EGR) on combustion and emissions of an automotive direct injection diesel engine

Cooled exhaust gas recirculation (EGR) is a common way to control in-cylinder NO_x production and is used on most modern high-speed direct injection (HSDI) diesel engines. However EGR has different effects on combustion and emissions production that are difficult to distinguish (increase of intake temperature, delay of rate of heat release (ROHR), decrease of peak heat release, decrease in O₂ concentration (and thus of global air/fuel ratio (AFR)) and flame temperature, increase of lift-off length, etc.), and thus the influence of EGR on NO_x and particulate matter (PM) emissions is not perfectly understood, especially under high EGR rates. An experimental study has been conducted on a 2.0 l HSDI automotive diesel engine under low-load and part load conditions in order to distinguish and quantify some effects of EGR on combustion and NO_x/PM emissions. The increase of inlet temperature with EGR has contrary effects on combustion and emissions, thus sometimes giving opposite tendencies as traditionally observed, as, for example, the reduction of NO_x emissions with increased inlet temperature. For a purely diffusion combustion the ROHR is unchanged when the AFR is maintained when changing in-cylinder ambient gas properties (temperature or EGR rate). At low-load conditions, use of high EGR rates at constant boost pressure is a way to drastically reduce NO_x and PM emissions but with an increase of brake-specific fuel consumption (BSFC) and other emissions (CO and hydrocarbon), whereas EGR at constant AFR may drastically reduce NO_x emissions without important penalty on BSFC and soot emissions but is limited by the turbocharging system.     

Effects of exhaust gas recirculation (EGR) on combustion and emissions during cold start of direct injection (DI) diesel engine

Through experiments conducted on a single cylinder direct injection (DI) diesel engine, effects of exhaust gas recirculatoin (EGR) on combustion and emission during cold start were investigated. Combustion of first firing cycle can be promoted significantly by introducing EGR. In experiments, when partially closed choking valve and partially or fully opened EGR valve, peak cylinder pressure of first firing cycle was about 45% higher than that under normal condition without EGR, and the start of combustion (SOC) was also much earlier. EGR also had effects on combustion stability. In the case, which kept 50% or 100% opening of EGR valve (OEV) and kept 100% opening of choking valve (OCV), more stable combustion process was achieved when common rail pressure decreased during cold start. However, excessive amount of EGR led to extreme unstable combustion and even misfiring. Opacity and NO emissions were also analyzed in detail. In the case with maximum EGR, the lowest average opacity, which was less than 4%, was achieved during initial several firing cycles of cold start. But in the later phase, excessive amount of EGR led to a great deal of white smoke emission. NO emission during initial phase of cold start is mainly affected by increase in fuel amount of injection. When combustion became stable gradually, EGR showed significant effect on NO reduction.     

Experimental investigations on a hydrogen diesel homogeneous charge compression ignition engine with exhaust gas recirculation

In this experimental study, hydrogen was inducted along with air and diesel was injected into the cylinder using a high pressure common rail system, in a single cylinder homogeneous charge compression ignition engine. An electronic controller was used to set the required injection timing of diesel for best thermal efficiency. The influences of hydrogen to diesel energy ratio, output of the engine and exhaust gas recirculation (EGR) on performance, emissions and combustion were studied in detail. An increase in the amount of hydrogen improved the thermal efficiency by retarding the combustion process. It also lowered the exhaust emissions. Large amounts of hydrogen and EGR were needed at high outputs for suppressing knock. The range of operation was brake mean effective pressures of 2–4 bar. The levels of HC and CO emitted were not significantly influenced by the amount of hydrogen that was used.     

The comparison of engine performance and exhaust emission characteristics of sesame oil–diesel fuel mixture with diesel fuel in a direct injection diesel engine

The use of vegetable oils as a fuel in diesel engines causes some problems due to their high viscosity compared with conventional diesel fuel. Various techniques and methods are used to solve the problems resulting from high viscosity. One of these techniques is fuel blending. In this study, a blend of 50% sesame oil and 50% diesel fuel was used as an alternative fuel in a direct injection diesel engine. Engine performance and exhaust emissions were investigated and compared with the ordinary diesel fuel in a diesel engine. The experimental results show that the engine power and torque of the mixture of sesame oil–diesel fuel are close to the values obtained from diesel fuel and the amounts of exhaust emissions are lower than those of diesel fuel. Hence, it is seen that blend of sesame oil and diesel fuel can be used as an alternative fuel successfully in a diesel engine without any modification and also it is an environmental friendly fuel in terms of emission parameters.     

The effects of hydrogen enriched natural gas under different engine loads in a diesel engine

Natural gas, which is among the alternative fuels, has become widespread in the transportation as it is both economical and environmentally friendly. While the use of natural gas is at a significant level in spark ignition engines, it has not yet been implemented in compression ignition engines (CI) as it worsens combustion due to ignition delay. In CI engines, however, the combustion properties of natural gas (NG) can be improved by adding hydrogen (H₂) to NG. This is one of the methods applied to use natural gas in CI engines. In this experimental study, two different volumetric rates of NG and NG/H₂ mixtures were added to the combustion air in a CI engine, and engine performance and emissions were examined under different engine loads. The experiments were performed at two different engine speeds, four different engine loads and no-load condition. An engine cylinder pressure of 59.16 bar, which is the closest value to the 59.39 bar obtained in the use of diesel fuel, was obtained at 1500 rpm for “Diesel + NG(500 g/h)” and 59.9 bar (highest values) was obtained for “Diesel + (500 g/h) [80%NG+20%H₂]" at 1750 rpm. For “Diesel + NG(250 g/h)” (Mix1) and “Diesel + NG(500 g/h)” (Mix2), as the engine speed increases, at the point where the maximum in-cylinder pressure is obtained occurs further to the right from top dead center (TDC). With the addition of 500 g/h NG, an increase of 4.5% was achieved in the cylinder pressure at full load, while an increase of 6.5% was achieved in the case of using “Diesel + (500 g/h) [80%NG+20%H₂]". Although the effect of the NG and NG/H₂ mixtures on in-cylinder pressure was small, the fuel consumption and thermal efficiency improved. Substantial improvements in hydrocarbon (HC) emissions were observed with the use of “Diesel + (250 g/h)[80%NG+20%H₂]”. Carbon dioxide (CO₂) emissions decreased with speed increase, but no significant differences in terms of CO₂ emissions were observed between the mixtures. There was a maximum difference of 15% between the diesel and the mixtures in CO₂ emissions. Although there was a decrease in nitrogen oxide (NO_x) levels with the increase in engine speed, the lowest NO_x emissions of 447.6 ppmvol was observed in “Diesel + NG(250 g/h)” (Mix1) at 1750 rpm at maximum load.     

The deconvolution of the thermal, dilution, and chemical effects of exhaust gas recirculation (EGR) on the reactivity of engine and flame soot

In a recent paper, we demonstrated that the exhaust gas recirculation (EGR) enhanced the oxidative reactivity of diesel engine soot. In this paper, we show that simulated EGR, via carbon dioxide (CO₂) addition to the intake air to an engine at concentrations of 0, 2, 4, and 8 vol.% and to the oxidizer stream of an ethylene diffusion flame at concentrations of 0, 5, and 10 vol.%, affects the reactivity of the soot in the same manner as actual EGR. Motivated by this fact, post-flame ethylene soot was produced from a co-flow laminar diffusion flame to better understand the mechanism by which the CO₂ affects soot reactivity. This objective was accomplished by successfully isolating and examining the thermal, dilution, and chemical effects of the CO₂ on soot reactivity. These three effects account for 45%, 35%, and 20% of the total reactivity of soot respectively, with the thermal effect being the most important factor governing the soot reactivity. The results showed that all of these effects account for a measurable increase in soot reactivity.     

The effect of biodiesel fuel obtained from waste frying oil on direct injection diesel engine performance and exhaust emissions

In this study, usage of methyl ester obtained from waste frying oil (WFO) is examined as an experimental material. A reactor was designed and installed for production of methyl ester from this kind of oil. Physical and chemical properties of methyl ester were determined in the laboratory. The methyl ester was tested in a diesel engine with turbocharged, four cylinders and direct injection. Gathered results were compared with No. 2 diesel fuel. Engine tests results obtained with the aim of comparison from the measures of torque, power; specific fuel consumptions are nearly the same. In addition, amount of emission such as CO, CO₂, NO_x, and smoke darkness of waste frying oils are less than No. 2 diesel fuel.     

The effect of reformer gas mixture on the performance and emissions of an HSDI diesel engine

Exhaust gas assisted fuel reforming is an attractive on-board hydrogen production method, which can open new frontiers in diesel engines. Apart from hydrogen, and depending on the reactions promoted, the reformate typically contains a significant amount of carbon monoxide, which is produced as a by-product. Moreover, admission of reformed gas into the engine, through the inlet pipe, leads to an increase of intake air nitrogen to oxygen ratio. It is therefore necessary to study how a mixture of syngas and nitrogen affects the performance and emissions of a diesel engine, in order to gain a better understanding of the effects of supplying fuel reformer products into the engine.     

An overview of physical and chemical features of diesel exhaust particles

Diesel exhaust particles have a negative impact on both human health and the ecosystem. An adequate understanding of the physical and chemical characteristics of diesel exhaust particles is essential for both minimizing particles formation and optimizing particles oxidation. This paper systematically reviews the physicochemical characteristics of diesel exhaust particles. Firstly, the approaches to studying the characteristics of diesel exhaust particles are described and the main features of particulate matter (PM) such as particle size distributions, microstructure of aggregate particles, nanostructure of primary particle, chemical compositions of diesel particles and oxidation reactivity of diesel particles are discussed in this paper. Then, the effects of operating parameters containing engine speed, engine load, injection pressure, injection timing and exhaust gas recirculation (EGR) on each PM feature are summarized and discussed in detail. Subsequently, the relationships between PM features and its oxidation reactivity are exclusively reviewed. It can be concluded that soot oxidation reactivity is influenced by the combination of multiple properties of the emitted PM. Finally, concluding remarks are presented and further research recommendations are listed.     

Effect of H2 addition on combustion and exhaust emissions in a heavy-duty diesel engine with EGR

The effect of the addition of hydrogen (H₂) on the combustion process and nitric oxide (NO) formation in a H₂-diesel dual fuel engine was numerically investigated. The model developed using AVL FIRE as a platform was validated against the cylinder pressure and heat release rate measured with the addition of up to 6% (vol.) H₂ into the intake mixture of a heavy-duty diesel engine with exhaust gas recirculation (EGR). The validated model was applied to further explore the effect of the addition of 6%–18% (vol.) H₂ on the combustion process and formation of NO in H₂-diesel dual fuel engines. When the engine was at N = 1200 rpm and 70% load, the simulation results showed that the addition of H₂ prolonged ignition delay, enhanced premixed combustion, and promoted diffusion combustion of the diesel fuel. The maximum peak cylinder pressure was observed with addition of 12% (vol.) H₂. In comparison, the maximum peak heat release rate was observed with the addition of 16% (vol.) H₂. The addition of H₂ was a crucial factor dominating the increased NO emissions. Meanwhile, the addition of H₂ reduced soot emissions substantially, which may be due to the reduced diesel fuel burned each cycle. Furthermore, proper combination of adding H₂ with EGR can improve combustion performance and reduce NO emissions.     

Analysis of combustion characteristics,engine performance and exhaust emissions of diesel engine fueled with upgraded waste source fuel

Utilization of the waste products as an alternative fuel could reduce the dependence on fossil fuel. The three types of upgraded waste source fuels discussed in this paper were tire derived fuel (TDF), waste plastic disposal fuel (WPD) and upgraded waste cooking oil (UWCO). The detailed combustion pressure showed that kinematic viscosity and cetane number played an important role in determining the combustion quality. TDF's high kinematic viscosity and low cetane number affected its fuel vaporization process; thus, lengthening its ignition delay. UWCO showed the 14% higher power and 13.8% higher torque compared to diesel fuel (DF). WPD produced the lowest NOx due to its low pressure curve during combustion. TDF had produced the highest exhaust emissions (CO, CO₂, NO and NOx). Particulate matter (PM) emissions by UWCO blends were lower than DF. UWCO's soot concentration was 40% lower than DF and increased to 62.5% from low to high engine speed operation.