Lithium ion impregnated calcium oxide as nano catalyst for the biodiesel production from karanja and jatropha oils

Lithium impregnated calcium oxide has been prepared by wet impregnation method in nano particle form as supported by powder X-ray diffraction and transmission electron microscopy. Basic strength of the same was measured by Hammett indicators. Calcium oxide impregnated with 1.75 wt% of lithium was used as solid catalyst for the transesterification karanja and jatropha oil, containing 3.4 and 8.3 wt% of free fatty acids, respectively. The reaction parameters, viz., reaction temperature, alcohol to oil molar ratio, free fatty acid contents, amount of catalyst and amount of impregnated lithium ion in calcium oxide support, have been studied to establish the most suitable condition for the transesterification reaction. The complete transesterification of karanja and jatropha oils was achieved in 1 and 2 h, respectively, at 65 °C, utilizing 12:1 molar ratio of methanol to oil and 5 wt% (catalyst/oil, w/w) of catalyst. Few physicochemical properties of the prepared biodiesel samples have been studied and compared with standard values.     

Alkaline-catalyzed transesterification of Silurus triostegus Heckel fish oil: Optimization of transesterification parameters

The present work reports the production of biodiesel from Silurus triostegus Heckel fish oil (STFO) through alkaline-catalyzed transesterification by using potassium hydroxide (KOH) as an alkaline catalyst with methanol. Chemical and physical properties of the extracted oil were determined. It was found that STFO has a low acid value (1.90 mg KOH/g oil); hence no pre-treatment such as acid esterification is required to produce the biodiesel. The influence of the experimental parameters such as KOH concentration (0.25–1.0% w/w of oil), methanol to oil molar ratio (3:1, 6:1, 9:1 and 12:1), reaction temperature (32, 45 and 60 °C), reaction duration (30, 60, 90 and 120 min), type of the catalyst (potassium or sodium hydroxide) and step multiplicity (single- and two-step transesterification) on the yield of the biodiesel were investigated. The maximum biodiesel yield (96%) was obtained under the optimized parameters of the transesterification (KOH 0.50% w/w, 6:1 methanol to oil, at 32 °C for 60 min). The properties of the produced biodiesel were found to conform with the ASTM standard, indicating its suitability for internal combustion engines. Blending of the produced biodiesel with petro diesel with various volume percentages was investigated as well.     

Biodiesel synthesis from Hevea brasiliensis oil employing carbon supported heterogeneous catalyst: Optimization by Taguchi method

The present work illustrates the parametric effects on biodiesel production from Hevea brasiliensis oil (HBO) using flamboyant pods derived carbonaceous heterogeneous catalyst. Activated carbon (AC) was prepared maintaining 500 °C for 1 h and steam activated at optimised values of activation time 1.5 h and temperature 350 °C. Carbonaceous support was impregnated with KOH at different AC/KOH ratios. The transesterification process was optimized and significant parameters affecting the biodiesel yield was identified by Taguchi method considering four parameters viz. reaction time, reaction temperature, methanol to oil ratio and catalyst loading. The physicochemical properties of Hevea brasiliensis methyl ester (HBME) were examined experimentally at optimised condition and found to meet the global American standards for testing and materials (ASTM). The optimum condition observed to yield 89.81% of biodiesel were: reaction time 60 min, reaction temperature 55 °C, catalyst loading 3.5wt% and methanol to oil ratio 15:1. Contribution factor revealed that among four parameters considered, catalyst loading and methanol to oil ratio have more prominent effect on biodiesel yield. The cost for preparing carbonaceous catalyst support was estimated and observed to be fairly impressive. Thus, Hevea brasiliensis oil (HBO) could be considered as suitable feedstock and flamboyant pods derived carbon as effective catalyst for production of biodiesel.     

A comparative study of KOH/Al2O3 and KOH/NaY catalysts for biodiesel production via transesterification from palm oil

The transesterification of palm oil to methyl esters (biodiesel) was studied using KOH loaded on Al₂O₃ and NaY zeolite supports as heterogeneous catalysts. Reaction parameters such as reaction time, wt% KOH loading, molar ratio of oil to methanol, and amount of catalyst were optimized for the production of biodiesel. The 25 wt% KOH/Al₂O₃ and 10 wt% KOH/NaY catalysts are suggested here to be the best formula due to their biodiesel yield of 91.07% at temperatures below 70 °C within 2–3 h at a 1:15 molar ratio of palm oil to methanol and a catalyst amount of 3–6 wt%. The leaching of potassium species in both spent catalysts was observed. The amount of leached potassium species of the KOH/Al₂O₃ was somewhat higher compared to that of the KOH/NaY catalyst. The prepared catalysts were characterized by using several techniques such as XRD, BET, TPD, and XRF.     

A bronsted basic ionic liquid as an efficient and environmentally benign catalyst for biodiesel synthesis from soybean oil and methanol

Morpholine basic ionic liquid was synthesized with N-methyl morpholine, N-butyl bromide, and KOH by two-step method and was used to catalyze the transesterification of soybean oil with methanol to biodiesel. The structure of the catalyst were examined by ¹H nuclear magnetic resonance. The effects of the molar ratio of methanol to oil, reaction temperature, and amount of catalyst on the biodiesel yield were investigated. Optimized biodiesel yield of 94.5% was achieved with catalyst amount of 3.0 wt%, and methanol to soybean oil molar ratio of 14:1 at reaction temperature of 60 °C for 6 h. The catalyst has maintained sustained activity after being employed to six cycles. The prepared biodiesel component was analyzed by gas chromatography-mass spectrometry (GC-MS) and the results showed that the biodiesel comprised of hexadecanoic acid methyl ester, 10, 13-octadecadienoic acid methyl ester, 9-octadecenoic acid methyl ester, and octadecanoic acid methyl ester, illustrating that fatty acids of soybean oil were converted completely.     

Biodiesel from different oil using fixed-bed and plug-flow reactors

In this study, a pilot scale of 100 t/year biodiesel production system, mainly consisting of a fixed-bed and a down-stream plug-flow reactors, was setup to test different feedstock oils, especially a kind of high-acidified oil, trap grease, for their feasibility as biodiesel feedstock in China. The tested oils include three kinds of typical oil from Guangdong Province, China: rapeseed oil, Chinese wood oil, and trap grease. At the same time the optimum residence time for a plug-flow reactor to perform transesterification reaction was investigated in this study. At the temperature of 65 °C, methanol/oil molar ratio of 6:1 and KOH load of 1.2 wt% of oil, the optimum residence time was found to be 19 min. A type of ion-exchange resin was used to fill in the fixed-bed reactor and used as the esterification catalyst for pretreating on the high-acidified oil. For the fresh catalyst, the acid value of trap grease could be reduced from 114 mg KOH/g to about 2 mg KOH/g after 13 h at temperature 75 °C, catalyst load of 15 wt% of oil, methanol addition of 20 wt% of oil. The lifetime test for the catalyst indicated that its life is over 30 days. The quality of biodiesel derived from three feedstock oils is compared with newly published China BD100 standard of GB/T20828-2007. A comparison of the results reveals that the biodiesel generated through this system could satisfactorily meet China BD100 standard. It indicates that the designed process in this system has a good adaptability for different kinds of oil.     

Manufacturing of zeolite based catalyst from zeolite tuft for biodiesel production from waste sunflower oil

In the present work, zeolite based catalyst was prepared from zeolite tuft by impregnation methods. The zeolite tuft was initially treated with hydrochloric acid (16%) and then several KOH/zeolite catalysts were prepared by impregnation in KOH solutions. Various solutions of KOH with different molarities (1–6 M) were used. Further modification for the catalyst was performed by a 2nd step impregnation treatment by heating and stirring the KOH/zeolite to 80 °C for 4 h. The zeolite tuft and the prepared catalysts were characterized by several analytical techniques in order to explore their physicochemical properties. These tests include: X-Ray Fluorescence (XRF), Scanning Electron Microscopy (SEM), Zero point of Charge (PHzpc), Fourier Transform Infrared (FT-IR), Energy-dispersive X-Ray analysis (EDX) and X-Ray Diffraction (XRD). The catalysts were then used for transesterification of waste sunflower vegetable oil in order to produce biodiesel. Among the different catalysts prepared, the 1–4M KOH/TZT catalyst provided the maximum biodiesel yield of 96.7% at 50 °C reaction temperature, methanol to oil molar ratio of 11.5:1, agitation speed of 800 rpm, 335 μm catalyst particle size and 2 h reaction time. The physicochemical properties of the produced biodiesel comply with the EN and ASTM standard specifications.     

Production of biodiesel from food processing waste using response surface methodology

The optimum conditions for biodiesel production by the transesterification of waste oil form the pork grilling process in the food factory in Udon Thani, Thailand, using NaOH and KOH as catalysts, has been investigated. A Box–Behnken Design (BBD) followed by a Response Surface Methodology (RSM) with 30 runs was used to assess the significance of three factors: the methanol to oil molar ratio, the amount of NaOH and KOH used, and the reaction time required to achieve the optimum percent fatty acid methyl ester (%FAME). The measured %FAME following transesterification using NaOH as a catalyst was an optimum 95.6% with a methanol to oil molar ratio of 12.2:1, a NaOH percentage mass fraction of 0.49% and a reaction time of 63 min. Using KOH as a catalyst, the %FAME was an optimum 93.0% with a methanol to oil molar ratio of 12:1, a KOH percentage mass fraction of 0.61% and a reaction time of 72 min. The coefficient of determination (R²) for regression equations were 98.55% and 93.99%, respectively. The probability value (P<0.05) demonstrated a very good significance for the regression model. The physicochemical properties of the biodiesel obtained from the waste oil met the ASTM 6751 biodiesel standard, illustrating that waste oil from the pork grilling process can be used as a raw material for biodiesel production by transesterification.     

Mixed and ground KBr-impregnated calcined snail shell and kaolin as solid base catalysts for biodiesel production

Mixed and ground activated snail shell and kaolin catalysts impregnated with KBr were investigated. The snail shell and kaolin were calcined, mixed, and ground prior to immersion with KBr solution and subsequent activation at 500 °C for 3 h. The precursor and catalysts were characterized by thermal gravimetric analysis, Fourier transform infrared spectroscopy, X-ray diffraction, X-ray photoelectron spectroscopy, scanning electron microscopy, and Brunauer–Emmett–Teller surface area. The catalytic performance of the prepared catalysts was evaluated by transesterification of soybean oil with methanol. The effects of various parameters on biodiesel yield were investigated. A biodiesel yield of 98.5% was achieved using the catalyst prepared by 40% KBr-immersed, mixed, and ground snail shell and kaolin, which were activated at 500 °C. The transesterification conditions were as follows: reaction temperature, 65 °C; reaction time, 2 h; methanol-to-soybean oil molar ratio, 6:1; and catalyst amount (relative to the weight of soybean oil), 2.0 wt%. The solid catalyst could be reused for four times, and biodiesel yield remained over 73.6% for the fourth time.     

Biodiesel from low cost feedstocks: The effects of process parameters on the biodiesel yield

Biofuel (e.g. biodiesel) has attracted increasing attention worldwide as blending component or direct replacement for fossil fuel in fuel energized engines. The substitution of petroleum-based diesel with biodiesel has already attained commercial value in many of the developed countries around the world. However, the use of biodiesel has not expanded in developing countries mostly due to the high production cost which is associated with the expensive high-quality virgin oil feedstocks. This research focuses on producing of biodiesel from low cost feedstocks such as used cooking oil (UCO) and animal fat (AF) via alkaline catalyzed transesterification process investigating the effects of process parameters, for example (i) molar ratio of feedstock to methanol (ii) catalyst concentration (iii) reaction temperature and (iv) reaction period on the biodiesel yield. The biodiesel was successfully produced via transesterification process from low cost feedstocks. It was also observed that the process parameters directly influenced the biodiesel yield. The optimum parameters for maximum biodiesel yields were found to be methanol/oil molar ratio of 6:1, catalyst concentration of 1.25 wt% of oil, reaction temperature of 65 °C, reaction period of 2 h and stirring speed of 150 rpm. The maximum biodiesel yields at the optimum conditions were 87.4%, 89% and 88.3% for beef fat, chicken fat and UCO, respectively. The results demonstrate high potential of producing economically viable biodiesel from low cost feedstocks with proper optimization of the process parameters.     

Optimization of heterogeneous biodiesel production from waste cooking palm oil via response surface methodology

Heterogeneous transesterification of waste cooking palm oil (WCPO) to biodiesel over Sr/ZrO₂ catalyst and the optimization of the process have been investigated. Response surface methodology (RSM) was employed to study the relationships of methanol to oil molar ratio, catalyst loading, reaction time, and reaction temperature on methyl ester yield and free fatty acid conversion. The experiments were designed using central composite by applying 2⁴ full factorial designs with two centre points. Transesterification of WCPO produced 79.7% maximum methyl ester yield at the optimum methanol to oil molar ratio = 29:1, catalyst loading = 2.7 wt%, reaction time = 87 min and reaction temperature = 115.5 °C.     

Activity of homogeneous and heterogeneous catalysts,spectroscopic and chromatographic characterization of biodiesel: A review

Biofuel has got tremendous attraction for the last decade as an alternative source of energy. Bioethanol and biodiesel are two main products of first generation biofuel. Biodiesel is chemically fatty acid methyl esters prepared from various edible and non-edible oils. It has been used as a substitute to mineral diesel during the last decade. This review is about generation, transesterification, factors affecting transesterification, catalysts (homogeneous and heterogeneous) and physico-chemical characterization of biodiesel by chromatographic and spectroscopic techniques. The alkaline homogeneous catalysts (NaOH or KOH) have been used on commercial scale for production of biodiesel because these are cheap and reaction occurs in less time. The heterogeneous catalysts such as metal oxides, e.g., CaO, MgO, SrO, ZnO, La₂O₃, Mg–Al hydrolalcite have been used for transesterification of vegetable oil due to their easy separation and reuse but these catalysts take more time for completion of reaction. The yield of biodiesel may be affected by alcohol/oil ratio, concentration of catalyst, time required for reaction, temperature free fatty acid moisture. The prepared biodiesel has been characterized by chromatographic techniques like gas chromatography, gas chromatography–mass spectroscopy, high performance liquid chromatography and spectroscopic techniques like nuclear magnetic resonance and infrared spectroscopy.     

Biodiesel production from soybean and Jatropha oils using cesium impregnated sodium zirconate as a heterogeneous base catalyst

Cesium modified sodium zirconate (Cs-Na₂ZrO₃) was prepared by ionic exchange from sodium zirconate (Na₂ZrO₃), which was synthesized via a solid state reaction. Both ceramics, i.e., pristine Na₂ZrO₃ and the Cs-Na₂ZrO₃, were used as basic heterogeneous catalysts in biodiesel production. Soybean and Jatropha oils were used as triglyceride sources for transesterification reactions. Parameters, such as catalyst concentration (between 0.5 and 3 wt%), reaction time, different methanol/vegetable oil molar ratios, and temperature of the reaction, were evaluated. The cesium cation influence was evaluated from the basic transesterification reactivity. The results showed that the introduction of cesium significantly modified the catalytic activity in biodiesel production. Cs enhanced the reaction kinetics in obtaining biodiesel and reduced the reaction time in comparison with pristine Na₂ZrO₃. The results showed that Cs-Na₂ZrO₃ as a basic heterogeneous catalyst exhibited the best fatty acid methyl esters (FAME) conversion for soybean oil (98.8%) at 1 wt%, 30:1 methanol/oil ratio, 65 °C, and 15 min. The best conditions for Jatropha oil (90.8%) were 3 wt%, 15:1 methanol/oil ratio, 65 °C, and 1 h. The impregnation of Na₂ZrO₃ with cesium represents a very exciting alternative heterogeneous base catalyst for biodiesel production.     

A comparative study of vegetable oil methyl esters (biodiesels)

In the present study, rubber seed oil, coconut oil and palm kernel oil, which are locally available especially in Kerala (India), are chosen and their transesterification processes have been investigated. The various process variables like temperature, catalyst concentration, amount of methanol and reaction time were optimized. Biodiesel from rubber seed oil (with high free fatty acid) was produced by employing two-step pretreatment process (acid esterification) to reduce acid value from 48 to 1.72 mg KOH/g with 0.40 and 0.35 v/v methanol-oil ratio and 1.0% v/v H₂SO₄ as catalyst at a temperature of 63(±2) °C with 1 h reaction time followed by transesterification using methanol-oil ratio of 0.30 v/v, 0.5 w/v KOH as alkaline catalyst at 55(±2) °C with 40 min reaction time to yield 98-99% biodiesel. Coconut oil and palm oil, being edible oils, transesterification with 0.25 v/v methanol-oil ratio, 0.50% w/v KOH as at 58(±2) °C, 20 min reaction time for coconut oil and 0.25% v/v methanol-oil ratio, 0.50% w/v KOH as alkaline catalyst at 60(±2) °C for palm kernel oil will convert them to 98-99% biodiesel. The brake thermal efficiency of palm oil biodiesel was higher with lower brake specific fuel consumption, but rubber seed oil biodiesel(ROB) showed less emission (CO and NO_x) compared to other biodiesels.     

Biodiesel production from refined sunflower vegetable oil over KOH/ZSM5 catalysts

ZSM5 zeolite was impregnated with different KOH loadings (15 wt.%, 25 wt.% and 35 wt.%) to prepare a series of KOH/ZSM5 catalysts. The catalysts were calcined at 500 °C for 3 h and then characterized by N₂ adsorption–desorption and X-ray diffraction (XRD) techniques. The catalysts were tested in the transesterification reaction in a batch reactor at 60 °C and under atmospheric pressure. It was found that KOH/ZSM5 with 35 wt.% loading showed the best catalytic performance. The best reaction conditions in the presence of KOH/ZSM5 (35 wt.%) were determined while modifying the catalyst to oil ratio and the reaction time. The highest methyl ester yield (>95%) was obtained for a reaction time of 24 h, a catalyst to oil ratio of 18 wt.%, and a methanol to oil molar ratio of 12:1. The properties of produced biodiesel complied with the ASTM specifications. The catalytic stability test showed that 35KOH/ZSM5 was stable for 3 consecutive runs. Characterization of the spent catalyst indicated that a slight deactivation might be due to the leaching of potassium oxides active sites.     

Biodiesel production using gel‐type cation exchange resin at different ionic forms

In this study, a strong acidic‐type cation exchange resin was used in the transesterification of corn oil to fatty acid methyl esters (FAME). The gel‐type cation exchange resin (Purolite‐PD206) was used in H⁺ and Na⁺ forms to utilize ion‐exchange resin as effective heterogeneous catalyst in the production of biodiesel. Effect of ionic forms of ion exchange resin on free fatty acid (FFA) conversion and composition was investigated by using different amounts of ion exchange resin (12, 16, and 20 wt%), various mole ratios of methanol to oil (1:6, 1:12, and 1:18 mol/mol), reaction temperatures (63, 65, and 67°C), and reaction time (24, 36, and 48 h) during transesterification reaction. The highest FFA conversions of 73.5% and 79.45% were obtained at conditions of 20 wt% of catalyst, 65°C of reaction temperature, 18:1 as methanol to oil ratio, and 48 h of reaction time for H⁺ and Na⁺ forms of ion exchange resin, respectively. These results were obtained from regression equations established by using analysis of variance (ANOVA) model according to the experimental results of selected parameters. Gas chromatography analysis revealed that FAME is mainly composed of C16:0 (palmitic), C18:1 (oleic), and C18:2 (linoleic) acids of methyl ester.     

Synthesis of fatty acid methyl esters via the transesterification of waste cooking oil by methanol with a barium-modified montmorillonite K10 catalyst

The transesterification of waste cooking oil (WCO) with methanol to produce fatty acid methyl esters (FAMEs) in the presence of barium-modified montmorillonite K10 (BMK10) catalyst was investigated in a batch reactor. The influence of the reaction parameters on the yield of FAME was investigated. The highest value of 83.38% was obtained with 3.5 wt% catalyst loading at 150 °C with a methanol: oil molar ratio of 12:1 during a reaction time of 5 h. BMK10 is a promising low-cost catalyst for the transesterification of WCO to produce FAME.     

Biodiesel production by transesterification of duck tallow with methanol on alkali catalysts

Duck tallow was employed as a feedstock for the production of biodiesel by transesterification with methanol. The content of fatty acid methyl ester (FAME) was evaluated on various alkali catalysts during transesterification. The composition and chemical properties of the FAME were investigated in the raw duck tallow and the biodiesel products. The major constituent in the biodiesel product was oleic acid. The FAME content was 97% on KOH catalyst in the reaction. It was acceptable for the limit of European biodiesel qualities for BD100. Acid value, density, and kinematic viscosity of the biodiesel products also came up to the biodiesel qualities.     

Biodiesel production from mixture of mahua and simarouba oils with high free fatty acids

A suitable process comprising acid pretreatment followed by main base transesterification reaction was developed to produce biodiesel from mixture of Mahua (M) and Simarouba (S) oils with high free fatty acids (FFA). The acid pretreatment reduced the high FFAs of the mixture of oils to around 1% which were then transesterified with methanol and KOH as catalyst at a reaction temperature of 60 °C. A genetic algorithm coupled with artificial neural network (ANN-GA) model to obtain the best pretreatment process parameters for bringing down the FFA level of individual vegetable oils to around 1% was modified to include the wide range of oils and validated for mixtures of M and S oils. The quality of biodiesel produced was analyzed by gas chromatography (GC), which indicated above 90% ester conversion. The fuel properties of biodiesel were found to be comparable to diesel and were conforming to the latest biodiesel standards.     

花椒籽油生物柴油制备工艺研究

以花椒籽油为原料,对KOH催化其与甲醇发生酯交换反应制备生物柴油进行研究。采用物理萃取法降低花椒籽油中游离脂肪酸的含量,三次萃取后酸值达到2 mgKOH/g以下。研究了花椒籽油和甲醇在氢氧化钾催化下的酯交换反应。进行了不同醇油摩尔比、催化剂用量、反应时间、反应温度等反应条件下对产率的影响,得到最佳反应条件为醇油物质的量之比为12∶1,催化剂添加量为油脂质量的1.2%,反应温度为60～65℃,反应时间为45 min。