Deactivation mechanism of Pd supported on ordered and non-ordered mesoporous silica in the direct H2O2 synthesis using CO2-expanded methanol

The deactivation mechanism of Pd supported on silica and mesoporous silica (SBA-15) using CO₂-expanded methanol as solvent was studied in the direct synthesis of H₂O₂ in batch and semi-continuous batch reactor tests as well as its hydrogenolysis. Fresh and used catalysts were characterized by TPR and CO chemisorption. The results evidence the presence of deactivation, which can be correlated to the loss of accessible active metal surface area due to sintering of Pd, but there is also an effect of the presence of the ordered mesoporous structure and of the reaction conditions. The higher concentration of H₂ in solution in semi-continuous batch reactor tests with respect to batch reactor tests leads to a more relevant deactivation in Pd-SiO₂ with respect to Pd-SBA-15, but a higher initial activity, due to the fact that H₂ accelerates the reduction of the Pd species which are less reducible in Pd-SiO₂ than in Pd-SBA-15. Pd-SBA-15 shows a higher H₂O₂ selectivity and productivity with respect to Pd-SiO₂ in batch reactor tests, related to the presence of easier reducible Pd species. Another difference is related to the different mechanism of sintering. On the SBA-15 support, due to the presence of the ordered mesoporosity, the Pd particles migrate into the SBA-15 channels forming elongated 1D-type particles. In Pd-SiO₂ catalyst, instead, the sintering of the Pd particles leads to large aggregates of Pd particles in the range of 20-25 nm.     

Study of ruthenium supported on Ta2O5–ZrO2 and Nb2O5–ZrO2 as catalysts for the partial oxidation of methane

Ru-based catalysts supported on Ta₂O₅–ZrO₂ and Nb₂O₅–ZrO₂ are studied in the partial oxidation of methane at 673–873 K. Supports with different Ta₂O₅ or Nb₂O₅ content were prepared by a sol–gel method, and RuCl₃ and RuNO(NO₃)₃ were used as precursors to prepare the catalysts (ca. 2 wt.% Ru). At 673 K high selectivity to CO₂ was found. An increase of temperature up to 773 K produced an increase in the selectivity to syngas (H₂/CO = 2.2–3.1), and this is related with the transformation of RuO₂ to metallic Ru as was determined from XRD and XPS results. At 873 K and with co-fed CO₂ an increase of the catalytic activity and CO selectivity was found. A TOF value of 5.7 s⁻¹ and H₂/CO ratio ca. 1 was achieved over Ru(Cl)/6TaZr. Catalytic results are discussed as a function of the support composition and characteristics of Ru-based phases.     

Preparation, characterization and photocatalytic activity of TiO2 impregnated with the heteropolyacid H3PW12O40: Photo-assisted degradation of 2-propanol in gas–solid regime

Both commercial and home prepared TiO₂ samples impregnated with tungstophosphoric acid (H₃PW₁₂O₄₀) were prepared and used for the photo-assisted degradation of 2-propanol in gas–solid regime. The characterization results evidenced a good coverage of the polyoxometalate (POM) onto the surface of both types of TiO₂ samples along with a marginal effect of the presence of ethanol or HCl during the POM impregnation step on the specific surface area, porosity, morphology, crystallinity and acidity of the samples. Propene was the main intermediate product found in 2-propanol photocatalytic degradation by using the samples containing POM as the photocatalyst, whereas propanone was mainly obtained when the photocatalyst was bare TiO₂. Acetaldehyde was also an intermediate product and its amount was always significantly smaller with respect to propanone and propene (when formed). Carbon dioxide and water were the ultimate oxidation products. The selectivity to propene has been attributed to the acidity of the POM supported samples.     

Direct formation of H2O2 from H2 and O2 and decomposition/hydrogenation of H2O2 in aqueous acidic reaction medium over halide-containing Pd/SiO2 catalytic system

Formation of H₂O₂ from H₂ and O₂ and decomposition/hydrogenation of H₂O₂ have been studied in aqueous acidic medium over Pd/SiO₂ catalyst in presence of different halide ions (viz. F⁻, Cl⁻ and Br⁻). The halide ions were introduced in the catalytic system via incorporating them in the catalyst or by adding into the reaction medium. The nature of the halide ions present in the catalytic system showed profound influence on the H₂O₂ formation selectivity in the H₂ to H₂O₂ oxidation over the catalyst. The H₂O₂ destruction via catalytic decomposition and by hydrogenation (in presence of hydrogen) was also found to be strongly dependent upon the nature of the halide ions present in the catalytic system. Among the different halides, Br⁻ was found to selectivity promote the conversion of H₂ to H₂O₂ by significantly reducing the H₂O₂ decomposition and hydrogenation over the catalyst. The other halides, on the other hand, showed a negative influence on the H₂O₂ formation by promoting the H₂ combustion to water and/or by increasing the rate of decomposition/hydrogenation of H₂O₂ over the catalyst. An optimum concentration of Br⁻ ions in the reaction medium or in the catalyst was found to be crucial for obtaining the higher H₂O₂ yield in the direct synthesis.     

Partial oxidation of ethanol over Pd/CeO2 and Pd/Y2O3 catalysts

The effect of the support nature on the performance of Pd catalysts during partial oxidation of ethanol was studied. H₂, CO₂ and acetaldehyde formation was favored on Pd/CeO₂, whereas CO production was facilitated over Pd/Y₂O₃ catalyst. According to the reaction mechanism, determined by DRIFTS analyses, some reaction pathways are favored depending on the support nature, which can explain the differences observed on products distribution. On Pd/Y₂O₃ catalyst, the production of acetate species was promoted, which explain the higher CO formation, since acetate species can be decomposed to CH₄ and CO at high temperatures. On Pd/CeO₂ catalyst, the acetaldehyde preferentially desorbs and/or decomposes to H₂, CH₄ and CO. The CO formed is further oxidized to CO₂, which seems to be promoted on Pd/CeO₂ catalyst.     

Comparison of the photocatalytic degradation of 2-propanol in gas–solid and liquid–solid systems by using TiO2–LnPc2 hybrid powders

Photocatalytic degradation of 2-propanol was carried out as a probe reaction both in gas–solid and in liquid–solid systems in the presence of TiO₂ both bare and impregnated with lanthanide (Sm, Gd, Ho) bis-phthalocyanines (LnPc₂) used as sensitizers. Continuous and batch photo-reactors, irradiated with an equal flux of photons, were used in gas–solid and in liquid–solid systems, respectively. Propanone and acetaldehyde were the main intermediates found in both systems during 2-propanol oxidation, whereas carbon dioxide and water were the final oxidation products exclusively in the gas–solid regime. The photocatalysts exhibited significantly higher activity in the liquid–solid system than in the gas–solid one. Samples impregnated with the sensitizers were apparently more photoactive than bare TiO₂. The highest photoactivity was shown by the 1.85 HoPc₂–TiO₂ sample.     

Preparation of Pdshell–Aucore/SiO2 catalyst and catalytic activity for acetylene hydrogenation

Various Pd shell thicknesses (0.12–1.5 nm) were synthesized on preformed Au particles of 5 nm size by seeded growth technique (15–80 at% Pd) using sodium citrate and tannic acid. The sols were characterized by UV–vis spectroscopy, TEM and high-resolution TEM (HRTEM) measurements. HRTEM confirmed the pseudomorphic growth of the Pd shell on the Au core. The Au/Pd core/shell particles were fixed onto SiO₂ (Aerosil 200) support by PDDA polycation. The catalytic activity in acetylene hydrogenation and selectivity of competition between acetylene and propene were tested after O₂ and H₂ pretreatment. The samples even in “as prepared” state hydrogenated acetylene. The thin Pd layer (15–30 at% Pd) on Au provided higher hydrogenation activity than the thick Pd shell. However, thermal treatment of the samples in H₂ stream causing Au/Pd intermixing shifted the activity maximum to higher Pd concentration (68–80 at% Pd). Comparison of the TOF (1/s) and selectivity values allowed us to conclude that the homogenized particle with 68–80 at% Pd shows better hydrogenation activity and selectivity than the thin Pd shell (15–30 at% Pd) on the Au core.     

The synthesis of Li(Ni1/3Co1/3Mn1/3)O2 using eutectic mixed lithium salt LiNO3–LiOH

A lithium-ion battery cathode material, Li(Ni_1/3Co_1/3Mn_1/3)O₂, with excellent electrochemical properties was prepared via two-step isothermal sintering, using eutectic lithium salts (0.38LiOH·H₂O–0.62LiNO₃) mixed with Co, Ni, or Mn hydroxides. Based on analysis using X-ray diffraction (XRD), scanning electron microscopy (SEM), a thermogravimetric-differential scanning calorimetric (TG–DSC) analyzer, and Fourier-transform Infrared (FT-IR), this synthetic process consists of procedures including lithium salt melting, permeation, reaction, crystalline transformation, and crystallization. Due to the lower melting point of the eutectic molten salts compared with that of the single lithium salt, a relatively mild synthetic condition (low temperature) is needed, and the product can be highly crystallized with low cation mixing, which facilitates maintenance of the precursor morphology. The electrochemical properties of the product were investigated by constant current discharge–charge and cyclic voltammetry. The results show that the initial discharge capacity is 160 mhA g⁻¹, with excellent cycling stability even after 50 cycles. We conclude that this novel eutectic molten salt method is a promising and practical approach for synthesizing cathode materials for lithium-ion batteries.     

Effect of Zr-ion substitution in CeO2 on H2O2-assisted degradation of orange G

A series of Pd ion-substituted CeO₂–ZrO₂ solid solutions were synthesized using the solution combustion technique. H₂O₂-assisted degradation of orange G was carried out in the presence of the catalysts. The activity of the catalysts was found to increase with the introduction of the second component in the solid solution, as signified by an increase in the rate constants and lowering of activation energy. The study showed the involvement of lattice oxygen and the importance of reducibility of the compound for the reaction.     

Low-temperature firing and microwave dielectric properties of 16CaO–9Li2O–12Sm2O3–63TiO2 ceramics with V2O5 addition

The sintering behaviors and microwave dielectric properties of the 16CaO–9Li₂O–12Sm₂O₃–63TiO₂ (abbreviated CLST) ceramics with different amounts of V₂O₅ addition had been investigated in this paper. The sintering temperature of the CLST ceramic had been efficiently decreased by nearly 100 °C. No secondary phase was observed in the CLST ceramics and complete solid solution of the complex perovskite phase was confirmed. The CLST ceramics with small amounts of V₂O₅ addition could be well sintered at 1200 °C for 3 h without much degradation in the microwave dielectric properties. Especially, the 0.75 wt.% V₂O₅-doped ceramics sintered at 1200 °C for 3 h have optimum microwave dielectric properties of Kr = 100.4, Q × f = 5600 GHz, and TCF = 7 ppm/°C. Obviously, V₂O₅ could be a suitable sintering aid that improves densification and microwave dielectric properties of the CLST ceramics.     

Performance of Pd catalysts supported on nanocrystalline α-Al2O3 and Ni-modified α-Al2O3 in selective hydrogenation of acetylene

Nanocrystalline α-Al₂O₃ and Ni-modified α-Al₂O₃ have been prepared by sol–gel and solvothermal methods and employed as supports for Pd catalysts. Regardless of the preparation method used, NiAl₂O₄ spinel was formed on the Ni-modified α-Al₂O₃ after calcination at 1150 °C. However, an addition of NiO peaks was also observed by X-ray diffraction for the solvothermal-made Ni-modified α-Al₂O₃ powder. Catalytic performances of the Pd catalysts supported on these nanocrystalline α-Al₂O₃ and Ni-modified α-Al₂O₃ in selective hydrogenation of acetylene were found to be superior to those of the commercial α-Al₂O₃ supported one. Ethylene selectivities were improved in the order: Pd/Ni-modified α-Al₂O₃–sol–gel > Pd/Ni-modified α-Al₂O₃-solvothermal ≈ Pd/α-Al₂O₃–sol–gel > Pd/α-Al₂O₃-solvothermal  Pd/α-Al₂O₃-commerical. As revealed by NH₃ temperature program desorption studies, incorporation of Ni atoms in α-Al₂O₃ resulted in a significant decrease of acid sites on the alumina supports. Moreover, XPS revealed a shift of Pd 3d binding energy for Pd catalyst supported on Ni-modified α-Al₂O₃–sol–gel where only NiAl₂O₄ was formed, suggesting that the electronic properties of Pd may be modified.     

Temperature dependence of electrochemically promoted NO reduction by C3H6 under stoichiometric conditions using Me/YSZ/Au (Me = Rh, RhPt, Pt) electrochemical catalysts

Temperature dependence of electrochemical promotion in C₃H₆–NO–O₂ reaction under stoichiometric conditions was investigated using Me/yttria-stabilized zirconia (YSZ)/Au (Me = Rh, RhPt, Pt) electrochemical catalysts, wherein electrodes were deposited by a sputtering method. Influences of the applied potential, the sintering extent of YSZ substrate, and the precious metal used for the electrode were investigated.Based on the analysis of catalytic reaction and electrode surface state, the longer sintering of YSZ substrate induced a positive effect for non-Faradaic electrochemical promotion of C₃H₆ oxidation by favoring oxygen spillover, and a negative effect for Faradaic electro-reduction of NO due to decrease in electrical conductivity. We postulated that RhPt electrode showed catalytic activity using the synergistic effect of Pt and Rh; however, higher activity than pure Rh electrode was not observed.     

High temperature SrCe0.9Eu0.1O3−δ proton conducting membrane reactor for H2 production using the water–gas shift reaction

The water–gas shift (WGS) reaction is used to shift the CO/H₂ ratio prior to Fischer–Tropsch synthesis and/or to increase H₂ yield. A WGS membrane reactor was developed using a mixed protonic–electronic conducting SrCe_0.9Eu_0.1O_3−δ membrane coated on a Ni–SrCeO_3−δ support. The membrane reactor overcomes the thermodynamic equilibrium limitations. A 46% increase in CO conversion and total H₂ yield was achieved at 900 °C under 3% CO and 6% H₂O, resulting in a 92% single pass H₂ production yield and 32% single pass yield of pure permeated H₂.     

Kinetic modeling of storage and reduction with different reducing agents (CO, H2, and C2 H4) on a Pt–Ba/-Al2O3 catalyst in the presence of CO2 and H2O

In this paper a global reaction kinetic model is used to understand and describe the NO_x storage/reduction process in the presence of CO₂ and H₂O. Experiments have been performed in a packed bed reactor with a Pt–Ba/γ-Al₂O₃ powder catalyst (1 wt% Pt and 30 wt% Ba) with different lean/rich cycle timings at different temperatures (200, 250, and ) and using different reductants (H₂, CO, and C₂H₄). Model simulations and experimental results are compared. H₂O inhibits the NO oxidation capability of the catalyst and no NO₂ formation is observed. The rate of NO storage increases with temperature. The reduction of stored NO with H₂ is complete for all investigated temperatures. At temperatures above , the water gas shift (WGS) reaction takes place and H₂ acts as reductant instead of CO. At , CO and C₂H₄ are not able to completely regenerate the catalyst. At the higher temperatures, C₂H₄ is capable of reducing all the stored NO, although C₂H₄ poisons the Pt sites by carbon decomposition at . The model adequately describes the NO breakthrough profile during 100 min lean exposure as well as the subsequent release and reduction of the stored NO. Further, the model is capable of simulating transient reactor experiments with 240 s lean and 60 s rich cycle timings.     

Sintering kinetics of α-Al2O3 powder

The sintering kinetics of α-Al₂O₃ powder are reviewed in this paper. The initial sintering of α-Al₂O₃ micropowder and α-Al₂O₃ nanopowder is all controlled by grain boundary diffusion. The sintering kinetics dominate up to a relative density of 0.77, where the coarsening kinetics dominate during further densification. Herring's scaling law can be used to predict the approximate sintering temperature of α-Al₂O₃ powder and demonstrates that if the particle size can be reduced to <20 nm, sintering below 1000°C may be possible. ©     

Efficient decomposition of organic compounds with FeTiO3/TiO2 heterojunction under visible light irradiation

FeTiO₃/TiO₂, a new heterojunction-type photocatalyst working at visible light, was prepared by a simple sol–gel method. Not only did FeTiO₃/TiO₂ exhibit greatly enhanced photocatalytic activity in decomposing 2-propanol in gas phase and 4-chlorophenol in aqueous solution, but also it induced efficient mineralization of 2-propanol under visible light irradiation (λ ≥ 420 nm). Furthermore, it showed a good photochemical stability in repeated photocatalytic applications. FeTiO₃ showed a profound absorption over the entire visible range, and its valence band (VB) position is close to that of TiO₂. The unusually high photocatalytic efficiency of the FeTiO₃/TiO₂ composite was therefore deduced to be caused by hole transfer between the VB of FeTiO₃ and TiO₂.     

Reduction and oxidation properties of Fe2O3/ZrO2 oxygen carrier for hydrogen production

Fe₂O₃ is a promising oxygen carrier for hydrogen production in the chemical-looping process. A set of kinetic studies on reduction with CH₄, CO and H₂ respectively, oxidation with water and oxygen containing Ar for chemical-looping hydrogen production was conducted. Fe₂O₃ (20 wt.%)/ZrO₂ was prepared by a co-precipitation method. The main variables in the TGA (thermogravimetric analyzer) experiment were temperatures and gas concentrations. The reaction kinetics parameters were estimated based on the experimental data. In the reduction by CH₄, CO and H₂, the reaction rate changed near FeO. Changes in the reaction rate due to phase transformation were observed at low temperature and low gas concentration during the reduction by CH₄, but the phenomenon was not remarkable for the reduction by CO and H₂. The reduction rate achieved using CO and H₂ was relatively faster than achieved using CH₄. The Hancock and Sharp method of comparing the kinetics of isothermal solid-state reactions was applied. A phase boundary controlled model (contacting sphere) was applied to the reduction of Fe₂O₃ to FeO by CH₄, and a different phase boundary controlled model (contacting infinite slab) was fit well to the reduction of FeO to Fe by CH₄. The reduction of Fe₂O₃ to Fe by CO and H₂ can be described by the former phase boundary controlled model (contacting sphere). This phase boundary controlled model (contacting sphere) also fit well for the oxidation of Fe to Fe₃O₄ by water and FeO to Fe₂O₃ by oxygen containing Ar. These kinetics data could be used to design chemical-looping hydrogen production systems.     

Catalytic syngas production from greenhouse gasses: Performance comparison of Ru-Al2O3 and Rh-CeO2 catalysts

In this work, 3% Ru-Al₂O₃ and 2% Rh-CeO₂ catalysts were synthesized and tested for CH₄-CO₂ reforming activity using either CO₂-rich or CO₂-lean model biogas feed. Low carbon deposition was observed on both catalysts, which negligibly influenced catalytic activity. Catalyst deactivation during temperature programmed reaction was observed only with Ru-Al₂O₃, which was caused by metallic cluster sintering. Both catalysts exhibited good stability during the 70 h exposure to undiluted equimolar CH₄/CO₂ gas stream at 750 °C. By varying residence time in the reactor during CH₄-CO₂ reforming, very similar quantities of H₂ were consumed for water formation. Reverse water-gas shift (RWGS) reaction occurred to a very similar extent either with low or high WHSV values over both catalysts, revealing that product gas mixture contained near RWGS equilibrium composition, confirming the dominance of WGS reaction and showing that shortening the contact time would actually decrease the H₂/CO ratio in the syngas produced by CH₄-CO₂ reforming, as long as RWGS is quasi equilibrated. H₂/CO molar ratio in the produced syngas can be increased either by operating at higher temperatures, or by using a feed stream with CH₄/CO₂ ratio well above 1.     

Flame-synthesized LaCoO3-supported Pd: 2. Catalytic behavior in the reduction of NO by H2 under lean conditions

A 0.5 wt% Pd/LaCoO₃, prepared by flame-spray pyrolysis (FP), was tested as catalyst for the low-temperature selective reduction of NO by H₂ in the presence of excess O₂. In particular, the effect of the precalcination and prereduction temperature on catalytic activity was compared with that of a similar Pd/LaCoO₃ sample prepared by impregnation with a Pd solution of FP-prepared LaCoO₃. The FP-made catalyst allowed full NO conversion at 150 °C, with 78% selectivity to N₂, thus outperforming the catalytic behavior of the corresponding sample prepared by impregnation. The higher activity of the FP-made catalyst has been attributed to the formation of segregated Co metal particles, not present in the impregnated sample, formed during the precalcination at 800 °C, followed by reduction at 300 °C. Two reaction mechanisms can be deduced from the temperature-programmed experiments. The first of these, occurring at lower temperatures, indicates cooperation between the Pd and Co metal particles, with formation of active nitrates on cobalt, successively reduced by hydrogen spillover from Pd. The second, occurring at higher temperature, allows 50% conversion of NO, with >90% selectivity to N₂, and involves N adatoms formed by dissociative NO adsorption over Pd. Prereduction at 600 °C led to a slight increase in catalytic activity, due to the formation of a PdCo alloy, which is more stable on reoxidization compared with Pd alone. Moreover, the cooperative reaction mechanism seems to be favored by the proximity of Co and Pd in metal particles.     

Thermal shock resistance of in situ formed Si2N2O–Si3N4 composites by gelcasting

Thermal shock resistance of Si₂N₂O–Si₃N₄ composites was evaluated by water quenching and subsequent three-point bending tests of strength diminution. Si₂N₂O–Si₃N₄ composites which was prepared with in situ liquid pressureless sintering process using Yb₂O₃ and Al₂O₃ powders as sintering additives by gelcasting showed no macroscopic cracks and the critical temperature difference (ΔT_c) could be up to 1400 °C. A mass of pores existed in the sintered body and the irregular shaped fibers extended from the pores increased the thermal shock property.