An Interdiffusion Method for Highly Performing Cesium/Formamidinium Double Cation Perovskites

The fabrication of high‐quality cesium (Cs)/formamidinium (FA) double‐cation perovskite films through a two‐step interdiffusion method is reported. Cs_x FA_1‐x PbI_{3‐y(1‐x )}Br_{y(1‐x )} films with different compositions are achieved by controlling the amount of CsI and formamidinium bromide (FABr) in the respective precursor solutions. The effects of incorporating Cs⁺ and Br^? on the properties of the resulting perovskite films and on the performance of the corresponding perovskite solar cells are systematically studied. Small area perovskite solar cells with a power conversion efficiency (PCE) of 19.3% and a perovskite module (4 cm²) with an aperture PCE of 16.4%, using the Cs/FA double cation perovskite made with 10 mol% CsI and 15 mol% FABr (Cs_0.1FA_0.9PbI_2.865Br_0.135) are achieved. The Cs/FA double cation perovskites show negligible degradation after annealing at 85 °C for 336 h, outperforming the perovskite materials containing methylammonium (MA).     

Synergetic Excess PbI2 and Reduced Pb Leakage Management Strategy for 24.28% Efficient,Stable and Eco-Friendly Perovskite Solar Cells

Introducing excess PbI₂ has proven to be an effective in situ passivation strategy for enhancing efficiency of perovskite solar cells (PSCs). Nevertheless, the photoinstability and hysteresis are still tough issues owing to the photolysis nature of PbI₂. Moreover, the humidity-related degradation of perovskite films is also a difficult territory to cover in such an in situ passivation strategy. Herein, a synergistic strategy is reported via initiatively inducing vertical graded PbI₂ distribution (GPD) in the whole perovskite film and capping a cis-Ru(H₂dcbpy)(dnbpy)(NCS)₂ (Z907) internal encapsulation (IE) layer on the surface to ameliorate the above issues. The GPD design can enhance luminescence, prolong carrier lifetimes, ascertaining the improvement of efficiency and elimination of photoinstability in the PSCs. Besides, the introduced IE layer not only can promote the moisture and thermal resistance, but also inhibit Pb leakage and ion migration in the PSCs. Through the synergetic regulations, the resultant PSCs exhibit an impressive open circuit voltage (V_OC) of 1.253 V, fill factor of 81.25%, and power conversion efficiency (PCE) of 24.28%. Moreover, the PSCs maintain 91% of its initial PCE at relative humidity of 85% after 500 h aging and 94% under continuous heating at 85 °C after 750 h aging.     

Synergistic effect of MACl and DMF towards efficient perovskite solar cells

The performance of perovskite solar cells (PSCs) is extremely dependent on morphology and crystallinity of perovskite film. One of the most effective methods to achieve high performance perovskite solar cells has been to introduce additives that serve as dopants, crystallization or passivation agents. Herein a facile strategy by introducing methylammonium chloride (MACl) and polar solvent N,N-Dimethylformamide (DMF) as co-additives in two-step sequential method is proposed to realize high quality perovskite film. It is demonstrated that DMF facilitates methylammonium iodide (MAI) penetrating easily into PbI₂ layer to form highly crystalized perovskite film with uniform morphology which is essential to achieve high V_OC. While MACl induces MAPbI₃ to crystallize in a pure α-phase and suppress non-photovoltaic phase, which guarantees high FF. Pure α-phase perovskite film with uniform morphology can be achieved by adopting MACl and DMF together and the corresponding solar cell illustrates a power conversion efficiency (PCE) of 19.02% with substantially promoted durability. Moreover, A V_OC as high as 1.181 V is succeeded for MAPbI₃ based solar cell benefiting from the synergistic effect.     

Nonfullerene Electron Transporting Material Based on Naphthalene Diimide Small Molecule for Highly Stable Perovskite Solar Cells with Efficiency Exceeding 20%

This study reports a new nonfullerene electron transporting material (ETM) based on naphthalene diimide (NDI) small molecules for use in high‐performance perovskite solar cells (PSCs). These solar cells simultaneously achieve high power conversion efficiency (PCE) of over 20% and long‐term stability. New NDI‐ID (N,N′‐Bis(1‐indanyl)naphthalene‐1,4,5,8‐tetracarboxylic diimide) consisting of an N‐substituted indane group having simultaneous alicyclic and aromatic characteristics is synthesized by a low‐cost, one‐step reaction, and facile purification method. The partially flexible characteristics of an alicyclic cyclopentene group on indane groups open the possibility of low‐temperature solution processing. The conformational rigidity and aromaticity of phenyl and alicyclic groups contribute to high temporal stability by strong secondary bonds. NDI‐ID has herringbone packed semiconducting NDI cores that exhibit up to 0.2 cm² V^?1 s^?1 electron mobility in field effect transistors. The inverted PSCs based on CH(NH₂)₂PbI_3–xBr_x with NDI‐ID ETM exhibit very high PCEs of up to 20.2%, which is better than that of widely used PCBM (phenyl‐C61‐butyric acid methyl ester) ETM‐based PSCs. Moreover, NDI‐ID‐based PSCs exhibit very high long‐term temporal stability, retaining 90% of the initial PCE after 500 h at 100 °C with 1 sun illumination without encapsulation. Therefore, NDI‐ID is a promising ETM for highly efficient, stable PSCs.     

Precursor Engineering for All‐Inorganic CsPbI2Br Perovskite Solar Cells with 14.78% Efficiency

The optoelectronic properties of perovskite films are closely related to the film quality, so depositing dense, uniform, and stable perovskite films is crucial for fabricating high‐performance perovskite solar cells (PSCs). CsPbI₂Br perovskite, prized for its superb stability toward light soaking and thermal aging, has received a great deal of attention recently. However, the air instability and poor performance of CsPbI₂Br PSCs are hindering its further progress. Here, an approach is reported for depositing high‐quality CsPbI₂Br films via the Lewis base adducts PbI₂(DMSO) and PbBr₂(DMSO) as precursors to slow the crystallization of the perovskite film. This process produces CsPbI₂Br films with large‐scale crystalline grains, flat surfaces, low defects, and long carrier lifetimes. More interestingly, PbI₂(DMSO) and PbBr₂(DMSO) adducts could significantly improve the stability of CsPbI₂Br films in air. Using films prepared by this technique, a power conversion efficiency (PCE) of 14.78% is obtained in CsPbI₂Br PSCs, which is the highest PCE value reported for CsPbI₂Br‐based PSCs to date. In addition, the PSCs based on DMSO adducts show an extended operational lifetime in air. These excellent performances indicate that preparing high‐quality inorganic perovskite films by using DMSO adducts will be a potential method for improving the performance of other inorganic PSCs.     

Hydrothermally Treated SnO2 as the Electron Transport Layer in High‐Efficiency Flexible Perovskite Solar Cells with a Certificated Efficiency of 17.3%

Perovskite solar cells (PSCs) are one of the most promising solar energy conversion technologies owing to their rapidly developing power conversion efficiency (PCE). Low‐temperature solution processing of the perovskite layer enables the fabrication of flexible devices. However, their application has been greatly hindered due to the lack of strategies to fabricate high‐quality electron transport layers (ETLs) at the low temperatures (≈100 °C) that most flexible plastic substrates can withstand, leading to poor performances for flexible PSCs. In this work, through combining the spin‐coating process with a hydrothermal treatment method, ligand‐free and highly crystalline SnO₂ ETLs are successfully fabricated at low temperature. The flexible PSCs based on this SnO₂ ETL exhibit an excellent PCE of 18.1% (certified 17.3%). The flexible PSCs maintained 85% of the initial PCE after 1000 bending cycles and over 90% of the initial PCE after being stored in ambient air for 30 days without encapsulation. The investigation reveals that hydrothermal treatment not only promotes the complete removal of organic surfactants coated onto the surface of the SnO₂ nanoparticles by hot water vapor but also enhances crystallization through the high vapor pressure of water, leading to the formation of high‐quality SnO₂ ETLs.     

Enhancing Stability of Efficient Perovskite Solar Cells (PCE ≈ 24.5%) by Suppressing PbI2 Inclusion Formation

Excess lead(II) iodide (PbI₂) has controversial roles in affecting the efficiency of perovskite solar cells (PSCs). Since the photoinstability of PbI₂ is now known to largely accelerate perovskite degradation, suppressing and/or eliminating excess PbI₂ is key to improving the stability of PSCs. Herein, process-dependent PbI₂ formation on the surfaces of formamidinium lead triiodide (FAPbI₃) films is examined. Due to the faster evaporation rate of organic substances, crystalline PbI₂ as an inclusion is found within the triple junction grain boundaries. With this hypothesis, two strategies are suggested: control of the 1) vapor pressure and 2) stoichiometry of precursor solutions to induce sufficient reaction of FAPbI₃. Although both strategies successfully eliminate the PbI₂ as inclusions, due to the slower evaporation rate, vapor pressure control films also exhibit a larger grain size (≈1.18 µm) with a good film quality to attain the highest power conversion efficiency (PCE) of 24.5%. Furthermore, the phase stability of α-FAPbI₃ is improved due to the elimination of the degradation sites induced by the photoinstability of PbI₂. The findings explore the formation process of unwanted PbI₂ (≈2.8%) and provide a simple method to effectively suppress its formation. This may further boost the PCE and stability, especially for FA-based perovskites.     

Two‐Step Sequential Deposition of Organometal Halide Perovskite for Photovoltaic Application

Organometal halide perovskite materials have become a superstar in the photovoltaic (PV) field because of their advantageous properties, which boost the power conversion efficiency (PCE) of perovskite solar cells (PSCs) from about 3.8% to above 22% in just seven years. Most importantly, such promising achievement is mainly based on its low‐cost and solution‐processed fabrication technique. One of the most promising and famous approaches to fabricating perovskite is a two‐step sequential deposition method because precursor (e.g., PbI₂) deposition is controllable, versatile, and flexible. Due to tremendous efforts, great progress has been achieved on the two‐step sequential deposition method, which helps to promote the development of PSCs. Herein, the progresses on the two‐step sequential deposition method of perovskite layers is reviewed thoroughly. At first, the reaction process and principle is introduced and discussed. Then, the research on the deposition techniques, structures, and compositions of precursors (the first step) is presented. Subsequently, the developments on the conversion techniques, conversion solutions, and growth of large crystals at the second step are introduced. Finally, four important issues on the two‐step sequential deposition method will be stated, accompanied with proposed solutions.     

Efficient and Ambient‐Air‐Stable Solar Cell with Highly Oriented 2D@3D Perovskites

3D organic–inorganic lead halide perovskites have shown great potential in efficient photovoltaic devices. However, the low stability of the 3D perovskite layer and random arrangement of the perovskite crystals hinder its commercialization road. Herein, a highly oriented 2D@3D ((AVA)₂PbI₄@MAPbI₃) perovskite structure combining the advantages of both 2D and 3D perovskite is fabricated through an in situ route. The highest power conversion efficiency (PCE) of 18.0% is observed from a 2D@3D perovskite solar cell (PSC), and it also shows significantly enhanced device stability under both inert (90% of initial PCE for 32 d) and ambient conditions (72% of initial PCE for 20 d) without encapsulation. The high efficiency of 18.0% and nearly twofold improvement of device stability in ambient compared with pure 3D PSCs confirm that such 2D@3D perovskite structure is an effective strategy for high performance and increasing stability and thus will enable the timely commercialization of PSCs.     

A Thienothiophene-Based Cation Treatment Allows Semitransparent Perovskite Solar Cells with Improved Efficiency and Stability

Perovskite surface treatment with additives has been reported to improve charge extraction, stability, and/or surface passivation. In this study, treatment of a 3D perovskite ((FAPbI₃)_1−x(MAPbBr₃)_x) layer with a thienothiophene-based organic cation (TTMAI), synthesized in this work, is investigated. Detailed analyses reveal that a 2D (n = 1) or quasi-2D layer does not form on the PbI₂-rich surface 3D perovskite. TTMAI-treated 3D perovskite solar cells (PSCs) fabricated in this study show improved fill factors, providing an increase in their power conversion efficiencies (PCEs) from 17% to over 20%. It is demonstrated that the enhancement is due to better hole extraction by drift-diffusion simulations. Furthermore, thanks to the hydrophobic nature of the TTMAI, PSC maintains 82% of its initial PCE under 15% humidity for over 380 h (the reference retains 38%). Additionally, semitransparent cells are demonstrated reaching 17.9% PCE with treated 3D perovskite, which is one of the highest reported efficiencies for double cationic 3D perovskites. Moreover, the semitransparent 3D PSC (TTMAI-treated) maintains 87% of its initial efficiency for six weeks (>1000 h) when kept in the dark at room temperature. These results clearly show that this study fills a critical void in perovskite research where highly efficient and stable semitransparent perovskite solar cells are scarce.     

Efficient Inverted Perovskite Solar Cells with a Fill Factor Over 86% via Surface Modification of the Nickel Oxide Hole Contact

The poor interface quality between nickel oxide (NiO_x) and halide perovskites limits the performance and stability of NiO_x-based perovskite solar cells (PSCs). Here a reactive surface modification approach based on the in situ decomposition of urea on the NiO_x surface is reported. The pyrolysis of urea can reduce the high-valence state of nickel and replace the adsorbed hydroxyl group with isocyanate. Combining theoretical and experimental analyses, the treated NiO_x films present suppressed surface states and improved transport energy level alignment with the halide perovskite absorber. With this strategy, NiO_x-based PSCs achieve a champion power conversion efficiency (PCE) of 23.61% and a fill factor of over 86%. The device's efficiency remains above 90% after 2000 h of thermal aging at 85 °C. Furthermore, perovskite solar modules achieve PCE values of 18.97% and 17.18% for areas of 16 and 196 cm², respectively.     

Constructing All-Inorganic Perovskite/Fluoride Nanocomposites for Efficient and Ultra-Stable Perovskite Solar Cells

Organic-inorganic hybrid perovskite solar cells (PSCs) have rapidly developed over the past decade and have achieved the latest certified power conversion efficiency (PCE) up to 25.5%. However, unsatisfactory long-term operational stability for these hybrid PSCs remains a huge obstacle to further development and commercialization. Herein, a unique hetero-structured CsPbI₃/CaF₂ perovskite/fluoride nanocomposites (PFNCs) is fabricated via a newly developed facile two-step hetero-epitaxial growth strategy to deliver efficient and ultra-stable PSCs. After being incorporated into the crystal lattice of α-phase CsPbI₃ perovskite, the cubic-phase CaF₂ in the resultant CsPbI₃/CaF₂ PFNCs can not only passivate the intrinsic defects of CsPbI₃ perovskite itself but also effectively suppress the notorious ion migration in hybrid perovskite Cs_0.05FA_0.81MA_0.14PbI_2.55Br_0.45 (CsFAMA) thin-films of PSCs. As such, the CsFAMA PSC devices based on CsPbI₃/CaF₂-deposited perovskite thin-film achieve a mean PCE of 20.45%, in sharp contrast to 19.33% of the control devices without deposition. Specifically, the CsPbI₃/CaF₂-deposited PSC retains 85% of its original PCE after 1000 h continuous operation at the maximum power point under AM 1.5G solar light, far better than those of the control and CsPbI₃-deposited PSCs with a device T₈₅ lifetime of 315 and 125 h, respectively.     

Improving the Extraction of Photogenerated Electrons with SnO2 Nanocolloids for Efficient Planar Perovskite Solar Cells

Great attention to cost‐effective high‐efficiency solar power conversion of trihalide perovskite solar cells (PSCs) has been hovering at high levels in the recent 5 years. Among PSC devices, admittedly, TiO₂ is the most widely used electron transport layer (ETL); however, its low mobility which is even less than that of CH₃NH₃PbI₃ makes it not an ideal material. In principle, SnO₂ with higher electron mobility can be regarded as a positive alternative. Herein, a SnO₂ nanocolloid sol with ≈3 nm in size synthesized at 60 °C was spin‐coated onto the fuorine‐doped tin oxide (FTO) glass as the ETL of planar CH₃NH₃PbI₃ perovskite solar cells. TiCl₄ treatment of SnO₂‐coated FTO is found to improve crystallization and increase the surface coverage of perovskites, which plays a pivotal role in improving the power conversion efficiency (PCE). In this report, a champion efficiency of 14.69% (J_sc = 21.19 mA cm^?2, V_oc = 1023 mV, and FF = 0.678) is obtained with a metal mask at one sun illumination (AM 1.5G, 100 mW cm^?2). Compared to the typical TiO₂, the SnO₂ ETL efficiently facilitates the separation and transportation of photogenerated electrons/holes from the perovskite absorber, which results in a significant enhancement of photocurrent and PCE.     

Combination of Hybrid CVD and Cation Exchange for Upscaling Cs‐Substituted Mixed Cation Perovskite Solar Cells with High Efficiency and Stability

Mixed cation hybrid perovskites such as Cs_xFA_1?xPbI₃ are promising materials for solar cell applications, due to their excellent photoelectronic properties and improved stability. Although power conversion efficiencies (PCEs) as high as 18.16% have been reported, devices are mostly processed by the anti‐solvent method, which is difficult for further scaling‐up. Here, a method to fabricate Cs_xFA_1?xPbI₃ by performing Cs cation exchange on hybrid chemical vapor deposition grown FAPbI₃ with the Cs⁺ ratio adjustable from 0 to 24% is reported. The champion perovskite module based on Cs_0.07FA_0.93PbI₃ with an active area of 12.0 cm² shows a module PCE of 14.6% and PCE loss/area of 0.17% cm^?2, demonstrating the significant advantage of this method toward scaling‐up. This in‐depth study shows that when the perovskite films prepared by this method contain 6.6% Cs⁺ in bulk and 15.0% at the surface, that is, Cs_0.07FA_0.93PbI₃, solar cell devices show not only significantly increased PCEs but also substantially improved stability, due to favorable energy level alignment with TiO₂ electron transport layer and spiro‐MeOTAD hole transport layer, increased grain size, and improved perovskite phase stability.     

Synergistic Effect of PbI2 Passivation and Chlorine Inclusion Yielding High Open‐Circuit Voltage Exceeding 1.15 V in Both Mesoscopic and Inverted Planar CH3NH3PbI3(Cl)‐Based Perovskite Solar Cells

Enhancing open‐circuit voltage in CH₃NH₃PbI₃(Cl) perovskite solar cells has become a major challenge for approaching the theoretical limit of the power conversion efficiency. Here, for the first time, it is demonstrated that the synergistic effect of PbI₂ passivation and chlorine incorporation via controlling the molar ratio of PbI₂, PbCl₂ (or MACl), and MAI in the precursor solutions, boosts the open‐circuit voltage of CH₃NH₃PbI₃(Cl) perovskite solar cells over 1.15 V in both mesoscopic and inverted planar perovskite solar cells. Such high open‐circuit voltage can be attributed to the enhanced photoluminescence emission and carrier lifetime associated with the reduced trap densities. The morphology and composition analysis using scanning electron microscopy, X‐ray diffraction measurements, and energy dispersive X‐ray spectroscopy confirm the high quality of the optimized CH₃NH₃PbI₃(Cl) perovskite film. On this basis, record‐high efficiencies of 16.6% for nonmetal‐electrode all‐solution‐processed perovskite solar cells and 18.4% for inverted planar perovskite solar cells are achieved.     

In Situ Growth of 2D Perovskite Capping Layer for Stable and Efficient Perovskite Solar Cells

2D halide perovskites have recently been recognized as a promising avenue in perovskite solar cells (PSCs) in terms of encouraging stability and defect passivation effect. However, the efficiency (less than 15%) of ultrastable 2D Ruddlesden–Popper PSCs still lag far behind their traditional 3D perovskite counterparts. Here, a rationally designed 2D‐3D perovskite stacking‐layered architecture by in situ growing 2D PEA₂PbI₄ capping layers on top of 3D perovskite film, which drastically improves the stability of PSCs without compromising their high performance, is reported. Such a 2D perovskite capping layer induces larger Fermi‐level splitting in the 2D‐3D perovskite film under light illumination, resulting in an enhanced open‐circuit voltage (V_oc) and thus a higher efficiency of 18.51% in the 2D‐3D PSCs. Time‐resolved photoluminescence decay measurements indicate the facilitated hole extraction in the 2D‐3D stacking‐layered perovskite films, which is ascribed to the optimized energy band alignment and reduced nonradiative recombination at the subgap states. Benefiting from the high moisture resistivity as well as suppressed ion migration of the 2D perovskite, the 2D‐3D PSCs show significantly improved long‐term stability, retaining nearly 90% of the initial power conversion efficiency after 1000 h exposure in the ambient conditions with a high relative humidity level of 60 ± 10%.     

Surface‐Modified Metallic Ti3C2Tx MXene as Electron Transport Layer for Planar Heterojunction Perovskite Solar Cells

MXenes are a large and rapidly expanding family of 2D materials that, owing to their unique optoelectronic properties and tunable surface termination, find a wide range of applications including energy storage and energy conversion. In this work, Ti₃C₂T_x MXene nanosheets are applied as a novel type of electron transport layer (ETL) in low‐temperature processed planar‐structured perovskite solar cells (PSCs). Interestingly, simple UV‐ozone treatment of the metallic Ti₃C₂T_x that increases the surface Ti? O bonds without any change in its bulk properties such as high electron mobility improves its suitability as an ETL. Improved electron transfer and suppressed recombination at the ETL/perovskite interface results in augmentation of the power conversion efficiency (PCE) from 5.00% in the case of Ti₃C₂T_x without UV‐ozone treatment to the champion PCE of 17.17%, achieved using the Ti₃C₂T_x film after 30 min of UV‐ozone treatment. As the first report on the use of pure MXene layer as an ETL in PSCs, this work shows the great potential of MXenes to be used in PSCs and displays their promise for applications in photovoltaic technology in general.     

Impact of the Solvation State of Lead Iodide on Its Two‐Step Conversion to MAPbI3: An In Situ Investigation

Producing high efficiency solar cells without high‐temperature processing or use of additives still remains a challenge with the two‐step process. Here, the solution processing of MAPbI₃ from PbI₂ films in N,N‐dimethylformamide (DMF) is investigated. In‐situ grazing incidence wide‐angle X‐ray scattering (GIWAXS) measurements reveal a sol–gel process involving three PbI₂‐DMF solvate complexes—disordered (P₀) and ordered (P₁, P₂)—prior to PbI₂ formation. When the appropriate solvated state of PbI₂ is exposed to MAI (methylammonium Iodide), it can lead to rapid and complete room temperature conversion into MAPbI₃ with higher quality films and improved solar cell performance. Complementary in‐situ optical reflectance, absorbance, and quartz crystal microbalance with dissipation (QCM‐D) measurements show that dry PbI₂ can take up only one third of the MAI taken up by the solvated‐crystalline P₂ phase of PbI₂, requiring additional annealing and yet still underperforming. The perovskite solar cells fabricated from the ordered P₂ precursor show higher power conversion efficiency (PCE) and reproducibility than devices fabricated from other cases. The average PCE of the solar cells is greatly improved from 13.2(±0.53)% (from annealed PbI₂) to 15.7(±0.35)% (from P₂) reaching up to 16.2%. This work demonstrates the importance of controlling the solvation of PbI₂ as an effective strategy for the growth of high‐quality perovskite films and their application in high efficiency and reproducible solar cells.     

Control over Light Soaking Effect in All-Inorganic Perovskite Solar Cells

Light soaking (LS) has been reported to positively influence the device performance of perovskite solar cells (PSCs), which, however, could be potentially harmful to the loaded devices due to the unstable output. There are very few reports on controls over the LS effect, especially in all-inorganic PSCs. In this study, a remarkable LS induced performance enhancement of CsPb(I_1−xBr_x)₃ based PSCs is presented. In situ grazing-incidence wide-angle X-ray scattering measurements quantize the temperature increase under illumination and reveal a radiative heating-induced lattice expansion. The device curing time is shortened with the increased Br/I ratio, evidently correlated with their distinct mobility and activation energy. It is suggested that LS could promote the migration of halide ions, giving rise to notable defect passivation and thus device improvements. Based on these understandings, an effective means is proposed to suppress the LS effect, which is to incorporate slightly over-stochiometric PbI₂ in precursor, and a champion PCE of 18.14% in all-inorganic PSCs with significantly reduced device curing time is obtained.     

Dual Additive for Simultaneous Improvement of Photovoltaic Performance and Stability of Perovskite Solar Cell

Additive engineering is one of the most efficient approaches to improve not only photovoltaic performance but also phase stability of formamidinium (FA)-based perovskite. Chlorine-based additives, such as methylammonium chloride (MACl), have been in general used to improve phase stability of FAPbI₃, which however often leads to loss of open-circuit voltage V_oc, accompanied by instability of the perovskite phase due to the volatile nature of the MA cation. A dual additive strategy for improving V_oc and thereby the overall efficiency are reported here. The mixing ratio of MACl to CsCl is varied from [MACl]/[CsCl] = 4 to 1, where V_oc increases with decreasing the ratio and best performance is achieved from [MACl]/[CsCl] = 2. As compared to the single source of MACl, the addition of CsCl reduces trap density and increases resistance against charge recombination, which is responsible for the increased V_oc. Moreover, defect passivation achieved by dual additive enables better stability than the single additive MACl as confirmed by long-term stability tests with unencapsulated devices for 50 days under relative humidity of about 40% at room temperature. The best power conversion efficiency of 23.22% is achieved by dual additive, which is higher than that for single additive of MACl or CsCl.