Threshold Identification for Micro‐Tomographic Damage Characterisation in a Short‐Fibre‐Reinforced Polymer

The micro‐tomographic technique represents an important tool for the analysis of the internal structure in short‐fibre‐reinforced polymers samples. For the investigation of damage mechanisms, detection of the micro‐voids within the matrix can be facilitated by applying a tensile load in‐situ during the scan. The investigations here described started from two micro‐CT acquisitions, at different strain levels, of the same PA6.6GF10 sample. An original procedure for micro‐voids identification is proposed, based on the statistical elaboration of the matrix grey‐tone range. In order to validate the suggested procedure beyond visual inspection, an independent method based on an optimisation approach, which puts to use the two available micro‐tomographic sets, was developed and applied. The effect of the tensile load, which can induce a progression of the damage within the specimen, was investigated, and the relations among strain, fibre distribution and micro‐voids volumetric fraction were studied. Our findings point out that the mechanisms of damage progression, even under static loading as in this case, appear to be more complex than those related to the fibre‐density‐induced stress concentrations alone and require further investigation.     

Design of a low cross‐talk micro‐coil array for micro‐scale MRI

Design of magnetic resonance micro‐coil arrays with low cross‐talk among the coils can be the main challenge to improve the effectiveness of magnetic resonance micro‐imaging because the electrical cross‐talk which is mainly due to the inductive coupling perturbs the sensitivity profile of the array and causes image artifacts. In this work, a capacitive decoupling network with N(M ? 1) + (N ? 1)(M ? 2) capacitors is proposed to reduce the inductive coupling in an N × M array. A 3 × 3 array of optimized micro‐coils is designed using the finite element simulations and all the needed elements for the array equivalent circuit are extracted in order to evaluate the effectiveness of the proposed decoupling method by assessing the reduction of the coupled signals after employing the capacitive network on the circuit. The achieved results for the designed array show that the high cross‐talk level is reduced by the factor of 2.2–3.4 after employing the capacitive network. By employing this method of decoupling, the adjacent coils in each row and inner columns can be decoupled properly while the minimum decoupling belongs to the outer columns because of the lack of all necessary decoupling capacitances for these columns. The main advantages of the proposed decoupling method are its efficiency and design easiness which facilitates the design of dense arrays with the properly decoupled coils, especially the inner coils which are more coupled due to their neighbors. © 2013 Wiley Periodicals, Inc. Int J Imaging Syst Technol, 23, 353–359, 2013     

Pencil‐Drawing Skin‐Mountable Micro‐Supercapacitors

In this study, integrated plaster‐like micro‐supercapacitors based on medical adhesive tapes are fabricated by a simple pencil drawing process combined with a mild solution deposition of MnO₂. These solid micro‐supercapacitors not only exhibit excellent stretchability, flexibility, and biocompatibility, but also possess outstanding electrochemical performances, such as exceptional rate capability and cycling stability. Hence they may act as skin‐mountable and thin‐film energy storage devices of high efficiency to power miniaturized and wearable electronic devices.     

One‐Step Synthesis of Monodispersed Mesoporous Carbon Nanospheres for High‐Performance Flexible Quasi‐Solid‐State Micro‐Supercapacitors

Cost‐effective synthesis of carbon nanospheres with a desirable mesoporous network for diversified energy storage applications remains a challenge. Herein, a direct templating strategy is developed to fabricate monodispersed N‐doped mesoporous carbon nanospheres (NMCSs) with an average particle size of 100 nm, a pore diameter of 4 nm, and a specific area of 1093 m² g^?1. Hexadecyl trimethyl ammonium bromide and tetraethyl orthosilicate not only play key roles in the evolution of mesopores but also guide the assembly of phenolic resins to generate carbon nanospheres. Benefiting from the high surface area and optimum mesopore structure, NMCSs deliver a large specific capacitance up to 433 F g^?1 in 1 m H₂SO₄. The NMCS electrodes–based symmetric sandwich supercapacitor has an output voltage of 1.4 V in polyvinyl alcohol/H₂SO₄ gel electrolyte and delivers an energy density of 10.9 Wh kg^?1 at a power density of 14014.5 W kg^?1. Notably, NMCSs can be directly applied through the mask‐assisted casting technique by a doctor blade to fabricate micro‐supercapacitors. The micro‐supercapacitors exhibit excellent mechanical flexibility, long‐term stability, and reliable power output.     

Inkjet‐Printed High‐Performance Flexible Micro‐Supercapacitors with Porous Nanofiber‐Like Electrode Structures

Flexible planar micro‐supercapacitors (MSCs) with unique loose and porous nanofiber‐like electrode structures are fabricated by combining electrochemical deposition with inkjet printing. Benefiting from the resulting porous nanofiber‐like structures, the areal capacitance of the inkjet‐printed flexible planar MSCs is obviously enhanced to 46.6 mF cm^?2, which is among the highest values ever reported for MSCs. The complicated fabrication process is successfully averted as compared with previously reported best‐performing planar MSCs. Besides excellent electrochemical performance, the resultant MSCs also show superior mechanical flexibility. The as‐fabricated MSCs can be highly bent to 180° 1000 times with the capacitance retention still up to 86.8%. Intriguingly, because of the remarkable patterning capability of inkjet printing, various modular MSCs in serial and in parallel can be directly and facilely inkjet‐printed without using external metal interconnects and tedious procedures. As a consequence, the electrochemical performance can be largely enhanced to better meet the demands of practical applications. Additionally, flexible serial MSCs with exquisite and aesthetic patterns are also inkjet‐printed, showing great potential in fashionable wearable electronics. The results suggest a feasible strategy for the facile and cost‐effective fabrication of high‐performance flexible MSCs via inkjet printing.     

A Gibbs‐energy‐barrier‐based computational micro‐sphere model for the simulation of martensitic phase‐transformations

We introduce a material model for the simulation of polycrystalline materials undergoing solid‐to‐solid phase‐transformations. As a basis, we present a scalar‐valued phase‐transformation model where a Helmholtz free energy function depending on volumetric and deviatoric strain measures is assigned to each phase. The analysis of the related overall Gibbs energy density allows for the calculation of energy barriers. With these quantities at hand, we use a statistical‐physics‐based approach to determine the resulting evolution of volume fractions. Though the model facilitates to take into account an arbitrary number of solid phases of the underlying material, we restrict this work to the simulation of phase‐transformations between an austenitic parent phase and a martensitic tension and compression phase. The scalar model is embedded into a computational micro‐sphere formulation in view of the simulation of three‐dimensional boundary value problems. The final modelling approach necessary for macroscopic simulations is accomplished by a finite element formulation, where the local material behaviour at each integration point is governed by the response of the micro‐sphere model.Copyright © 2014 John Wiley & Sons, Ltd.     

Zn‐Ion Hybrid Micro‐Supercapacitors with Ultrahigh Areal Energy Density and Long‐Term Durability

On‐chip micro‐supercapacitors (MSCs), as promising power candidates for microdevices, typically exhibit high power density, large charge/discharge rates, and long cycling lifetimes. However, as for most reported MSCs, the unsatisfactory areal energy density (<10 µWh cm^?2) still hinders their practical applications. Herein, a new‐type Zn‐ion hybrid MSC with ultrahigh areal energy density and long‐term durability is demonstrated. Benefiting from fast ion adsorption/desorption on the capacitor‐type activated‐carbon cathode and reversible Zn stripping/plating on the battery‐type electrodeposited Zn‐nanosheet anode, the fabricated Zn‐ion hybrid MSCs exhibit remarkable areal capacitance of 1297 mF cm^?2 at 0.16 mA cm^?2 (259.4 F g^?1 at a current density of 0.05 A g^?1), landmark areal energy density (115.4 µWh cm^?2 at 0.16 mW cm^?2), and a superb cycling stability without noticeable decay after 10 000 cycles. This work will inspire the fabrication and development of new high‐performance microenergy devices based on novel device design.     

Vertically Aligned Niobium Nanowire Arrays for Fast‐Charging Micro‐Supercapacitors

Planar micro‐supercapacitors are attractive for system on chip technologies and surface mount devices due to their large areal capacitance and energy/power density compared to the traditional oxide‐based capacitors. In the present work, a novel material, niobium nanowires, in form of vertically aligned electrodes for application in high performance planar micro‐supercapacitors is introduced. Specific capacitance of up to 1 kF m^?2 (100 mF cm^?2) with peak energy and power density of 2 kJ m^?2 (6.2 MJ m^?3 or 1.7 mWh cm^?3) and 150 kW m^?2 (480 MW m^?3 or 480 W cm^?3), respectively, is achieved. This remarkable power density, originating from the extremely low equivalent series resistance value of 0.27 Ω (2.49 µΩ m² or 24.9 mΩ cm²) and large specific capacitance, is among the highest for planar micro‐supercapacitors electrodes made of nanomaterials.     

The Effects of Electrode Force on the Mechanical Behaviour of Resistance Spot‐Welded 5083‐O Aluminium Alloy Joints

Abstract: In this study, the effects of electrode force on the static and fatigue strength of spot welded joints of 5083‐O aluminium alloy sheets were investigated. The thickness of the sheet joints was 1.5 mm. Tensile‐shear joints with one spot weld were considered and three different load levels for electrode force were selected as 2500 N, 3000 N and 3500 N while the welding time and electric current were fixed during resistance spot welding process. Also, micro‐structures and micro‐hardness of cross‐sectional area of the test samples were investigated. The results show that increasing the electrode force from 2500 N to 3000 N has no major impact on the nugget size and fatigue strength of the specimens, but increasing the electrode force from 3000 N to 3500 N, despite reducing in the diameter of the nuggets, increases the fatigue life of the joints significantly. The results also indicate that increasing the electrode force increases the life associated with the crack initiation phase of total fatigue lifetime.     

Experimental Investigations of Fracture Process in Concrete by Means of X‐ray Micro‐computed Tomography

The paper describes investigation results on fracture in notched concrete beams under quasi‐static three‐point bending by the X‐ray micro‐computed tomography. The two‐dimensional (2D) and three‐dimensional image procedures were used. Attention was paid to width, length, height and shape of cracks along beam depth. In addition, the displacements on the surface of concrete beams during the deformation process were measured with the 2D digital image correlation technique in order to detect strain localisation before a discrete crack occurred. The 2D fracture patterns in beams were numerically simulated with the finite‐element method using an isotropic damage constitutive model enhanced by a characteristic length of micro‐structure. Concrete was modelled as a random heterogeneous four‐phase material composed of aggregate, cement matrix, interfacial transitional zones and air voids. The advantages of the X‐ray micro‐computed tomography were outlined.     

Graphene‐Based Linear Tandem Micro‐Supercapacitors with Metal‐Free Current Collectors and High‐Voltage Output

Printable supercapacitors are regarded as a promising class of microscale power source, but are facing challenges derived from conventional sandwich‐like geometry. Herein, the printable fabrication of new‐type planar graphene‐based linear tandem micro‐supercapacitors (LTMSs) on diverse substrates with symmetric and asymmetric configuration, high‐voltage output, tailored capacitance, and outstanding flexibility is demonstrated. The resulting graphene‐based LTMSs consisting of 10 micro‐supercapacitors (MSs) present efficient high‐voltage output of 8.0 V, suggestive of superior uniformity of the entire integrated device. Meanwhile, LTMSs possess remarkable flexibility without obvious capacitance degradation under different bending states. Moreover, areal capacitance of LTMSs can be sufficiently modulated by incorporating polyaniline‐based pseudocapacitive nanosheets into graphene electrodes, showing enhanced capacitance of 7.6 mF cm^?2. To further improve the voltage output and energy density, asymmetric LTMSs are fabricated through controlled printing of linear‐patterned graphene as negative electrodes and MnO₂ nanosheets as positive electrodes. Notably, the asymmetric LTMSs from three serially connected MSs are easily extended to 5.4 V, triple voltage output of the single cell (1.8 V), suggestive of the versatile applicability of this technique. Therefore, this work offers numerous opportunities of graphene and analogous nanosheets for one‐step scalable fabrication of flexible tandem energy storage devices integrating with printed electronics on same substrate.