Room‐Temperature Partial Conversion of α‐FAPbI3 Perovskite Phase via PbI2 Solvation Enables High‐Performance Solar Cells

The two‐step conversion process consisting of metal halide deposition followed by conversion to hybrid perovskite has been successfully applied toward producing high‐quality solar cells of the archetypal MAPbI₃ hybrid perovskite, but the conversion of other halide perovskites, such as the lower bandgap FAPbI₃, is more challenging and tends to be hampered by the formation of hexagonal nonperovskite polymorph of FAPbI₃, requiring Cs addition and/or extensive thermal annealing. Here, an efficient room‐temperature conversion route of PbI₂ into the α‐FAPbI₃ perovskite phase without the use of cesium is demonstrated. Using in situ grazing incidence wide‐angle X‐ray scattering (GIWAXS) and quartz crystal microbalance with dissipation (QCM‐D), the conversion behaviors of the PbI₂ precursor from its different states are compared. α‐FAPbI₃ forms spontaneously and efficiently at room temperature from P₂ (ordered solvated polymorphs with DMF) without hexagonal phase formation and leads to complete conversion after thermal annealing. The average power conversion efficiency (PCE) of the fabricated solar cells is greatly improved from 16.0(±0.32)% (conversion from annealed PbI₂) to 17.23(±0.28)% (from solvated PbI₂) with a champion device PCE > 18% due to reduction of carrier recombination rate. This work provides new design rules toward the room‐temperature phase transformation and processing of hybrid perovskite films based on FA⁺ cation without the need for Cs⁺ or mixed halide formulation.     

FAPbI3‐Based Perovskite Solar Cells Employing Hexyl‐Based Ionic Liquid with an Efficiency Over 20% and Excellent Long‐Term Stability

Formamidinium lead triiodide (FAPbI₃)‐based perovskite materials are of interest for photovoltaics in view of their close‐to‐ideal bandgap, allowing absorption of photons over a broad solar spectrum. However, FAPbI₃‐based materials suffer from a notorious phase transition from the photoactive black phase (α‐FAPbI₃) to nonperovskite yellow phase (δ‐FAPbI₃) under ambient conditions. This transition dramatically reduces light absorbtion, thus, degrading the photovoltaic performance and stability of ensuring solar cells. In this study, 1‐hexyl‐3‐methylimidazolium iodide (HMII) ionic liquid (IL) is employed as an additive for the first time in FAPbI₃ perovskite to overcome the above‐mentioned issues. HMII incorporation facilitates the grain coarsening of FAPbI₃ crystal owing to its high‐polarity and high‐boiling point, which yields liquid domains between neighboring grains to reduce the activation energy of the grain‐boundary migration. As a result, the FAPbI₃ active layer exhibits micron‐sized grains with substantially suppressed parasitic traps with an Urbach energy reduced by 2 meV. Hence, the resulting perovskite solar cell achieves an efficiency of 20.6% with notable increase in open circuit voltage (V_OC) of 80 mV compared with HMII‐free cells (17.1%). More importantly, the HMII‐doped FAPbI₃‐based cells show a striking enhancement in shelf‐stability under high humidity and thermal stress, retaining >80% of their initial efficiencies at 60 ± 10% relative humidity and ≈95% at 65 °C.     

HPbI3: A New Precursor Compound for Highly Efficient Solution‐Processed Perovskite Solar Cells

Recently, there have been extensive research efforts on developing high performance organolead halide based perovskite solar cells. While most studies focused on optimizing the deposition processes of the perovskite films, the selection of the precursors has been rather limited to the lead halide/methylammonium (or formamidium) halide combination. In this work, we developed a new precursor, HPbI₃, to replace lead halide. The new precursor enables formation of highly uniform formamidium lead iodide (FAPbI₃) films through a one‐step spin‐coating process. Furthermore, the FAPbI₃ perovskite films exhibit a highly crystalline phase with strong (110) preferred orientation and excellent thermal stability. The planar heterojunction solar cells based on these perovskite films exhibit an average efficiency of 15.4% and champion efficiency of 17.5% under AM 1.5 G illumination. By comparing the morphology and formation process of the perovskite films fabricated from the formamidium iodide (FAI)/HPbI₃, FAI/PbI₂, and FAI/PbI₂ with HI additive precursor combinations, it is shown that the superior property of the HPbI₃ based perovskite films may originate from 1) a slow crystallization process involving exchange of H⁺ and FA⁺ ions in the PbI₆ octahedral framework and 2) elimination of water in the precursor solution state.     

Investigating the Superoxide Formation and Stability in Mesoporous Carbon Perovskite Solar Cells with an Aminovaleric Acid Additive

Perovskite solar cells have attracted a great deal of attention thanks to their high efficiency, ease of manufacturing, and potential low cost. However, the stability of these devices is considered their main drawback and needs to be addressed. Mesoporous carbon perovskite solar cells (m‐CPSC), consisting of three mesoporous layers (TiO₂/ZrO₂/C) infiltrated with CH₃NH₃PbI₃ (MAPI) perovskite, have presented excellent lifetimes of more than 10 000 h when the additive NH₂(CH₂)₄CO₂HI (5‐ aminovaleric acid iodide; 5‐AVAI) is used to modify the perovskite structure. Yet, the role of 5‐AVAI in enhancing the stability has yet to be determined. Here, superoxide‐mediated degradation of MAPI m‐CPSC with and without the 5‐AVAI additive is studied using the fluorescence probe dihydroethidium for superoxide detection. In situ X‐ray diffractometry shows that aminovaleric acid methylammonium lead iodide (AVA‐MAPI) perovskite infiltrated in mesoporous layers presents higher stability in an ambient environment under illumination, evidenced by a slower decrease of the MAPI/PbI₂ peak ratio. Superoxide yield measurements demonstrate that AVA‐MAPI generates more superoxide than regular MAPI when deposited on glass but generates significantly less when infiltrated in mesoporous layers. It is believed that superoxide formation in m‐CPSC is dependent on a combination of competitive factors including oxygen diffusion, sample morphology, grain size, and defect concentration.     

δ‐CsPbI3 Intermediate Phase Growth Assisted Sequential Deposition Boosts Stable and High‐Efficiency Triple Cation Perovskite Solar Cells

Cs/FA/MA triple cation perovskite films have been well developed in the antisolvent dripping method, attributable to its outstanding photovoltaic and stability performances. However, a facile and effective strategy is still lacking for fabricating high‐quality large‐grain triple cation perovskite films via sequential deposition method a, which is one of the key technologies for high efficiency perovskite solar cells. To address this issue, a δ‐CsPbI₃ intermediate phase growth (CsPbI₃‐IPG) assisted sequential deposition method is demonstrated for the first time. The approach not only achieves incorporation of controllable cesium into (FAPbI₃)_1–x(MAPbBr₃)_x perovskite, but also enlarges the perovskite grains, manipulates the crystallization, modulates the bandgap, and improves the stability of final perovskite films. The photovoltaic performances of the devices based on these Cs/FA/MA perovskite films with various amounts of the δ‐CsPbI₃ intermediate phase are investigated systematically. Benefiting from moderate cesium incorporation and intermediate phase‐assisted grain growth, the optimized Cs/FA/MA perovskite solar cells exhibit a significantly improved power conversion efficiency and operational stability of unencapsulated devices. This facile strategy provides new insights into the compositional engineering of triple or quadruple cation perovskite materials with enlarged grains and superior stability via a sequential deposition method.     

Layered Germanium Hybrid Perovskite Bromides: Insights from Experiments and First‐Principles Calculations

Metal halide perovskites are maturing as materials for efficient, yet low cost solar cells and light‐emitting diodes, with improving operational stability and reliability. To date however, most perovskite‐based devices contain Pb, which poses environmental concerns due to its toxicity; lead‐free alternatives are of importance to facilitate the development of perovskite‐based devices. Here, the germanium‐based Ruddledsen–Popper series (CH₃(CH₂)₃NH₃)₂(CH₃NH₃)_n?1Ge_nBr_3n+1 is investigated, derived from the parent 3D (n = ∞) CH₃NH₃GeBr₃ perovskite. Divalent germanium is a promising, nontoxic alternative to Pb²⁺ and the layered, 2D structure appears promising to bolster light emission, long‐term durability, and moisture tolerance. The work, which combines experiments and first principle calculations, highlights that in germanium bromide perovskites the optical bandgap is weakly affected by 2D confinement and the highly stereochemically active 4s² lone pair preludes to possible ferroelectricity, a topic still debated in Pb‐containing compounds.     

Synergistic Effect of PbI2 Passivation and Chlorine Inclusion Yielding High Open‐Circuit Voltage Exceeding 1.15 V in Both Mesoscopic and Inverted Planar CH3NH3PbI3(Cl)‐Based Perovskite Solar Cells

Enhancing open‐circuit voltage in CH₃NH₃PbI₃(Cl) perovskite solar cells has become a major challenge for approaching the theoretical limit of the power conversion efficiency. Here, for the first time, it is demonstrated that the synergistic effect of PbI₂ passivation and chlorine incorporation via controlling the molar ratio of PbI₂, PbCl₂ (or MACl), and MAI in the precursor solutions, boosts the open‐circuit voltage of CH₃NH₃PbI₃(Cl) perovskite solar cells over 1.15 V in both mesoscopic and inverted planar perovskite solar cells. Such high open‐circuit voltage can be attributed to the enhanced photoluminescence emission and carrier lifetime associated with the reduced trap densities. The morphology and composition analysis using scanning electron microscopy, X‐ray diffraction measurements, and energy dispersive X‐ray spectroscopy confirm the high quality of the optimized CH₃NH₃PbI₃(Cl) perovskite film. On this basis, record‐high efficiencies of 16.6% for nonmetal‐electrode all‐solution‐processed perovskite solar cells and 18.4% for inverted planar perovskite solar cells are achieved.     

Orientation Regulation of Tin‐Based Reduced‐Dimensional Perovskites for Highly Efficient and Stable Photovoltaics

Tin‐based perovskites have exhibited high potential for efficient photovoltaics application due to their outstanding optoelectrical properties. However, the extremely undesired instabilities significantly hinders their development and further commercialization process. A novel tin‐based reduced‐dimensional (quasi‐2D) perovskites is reported here by using 5‐ammoniumvaleric acid (5‐AVA⁺) as the organic spacer. It is demonstrated that by introducing appropriate amount of ammonium chloride (NH₄Cl) as additive, highly vertically oriented tin‐based quasi‐2D perovskite films are obtained, which is proved through the grazing incidence wide‐angle X‐ray scattering characterization. In particular, this approach is confirmed to be a universal method to deliver highly vertically oriented tin‐based quasi‐2D perovskites with various spacers. The highly ordered vertically oriented perovskite films significantly improve the charge collection efficiency between two electrodes. With the optimized NH₄Cl concentration, the solar cells employing quasi‐2D perovskite, AVA₂FA_n?1Sn_nI_3n+1 (<n> = 5), as light absorbers deliver a power conversion efficiency up to 8.71%. The work paves the way for further employing highly vertically oriented tin‐based quasi‐2D perovskite films for highly efficient and stable photovoltaics.     

Introduction of Hydrophobic Ammonium Salts with Halogen Functional Groups for High‐Efficiency and Stable 2D/3D Perovskite Solar Cells

2D perovskites have attracted extensive attention due to their excellent stability compared with 3D perovskites. However, the intrinsic hydrophilicity of introduced alkylammonium salts effects the humidity stability of 2D/3D perovskites. Devices based on longer chain alkylammonium salts show improvement in hydrophobicity but lower efficiency due to the poorer charge transport among various layers. To solve this issue, two hydrophobic short‐chain alkylammonium salts with halogen functional groups (2‐chloroethylamine, CEA⁺ and 2‐bromoethylamine, BEA⁺) are introduced into (Cs_0.1FA_0.9)Pb(I_0.9Br_0.1)₃ 3D perovskites to form 2D/3D perovskite structure, which achieve high‐quality perovskite films with better crystallization and morphology. The optimal 2D/3D perovskite solar cells (PSCs) with 5% CEA⁺ display a power conversion efficiency (PCE) as high as 20.08% under 1 sun irradiation. Because of the notable hydrophobicity of alkylammonium cations with halogen functional groups and the formed 2D/3D perovskite structure, the optimal PSCs exhibit superior moisture resistance and retain 92% initial PCE after aging at 50 ± 5% relative humidity for 2400 h. This work opens up a new direction for the design of new‐type 2D/3D PSCs with improved performance by employing proper alkylammonium salts with different functional groups.     

Defect Passivation via the Incorporation of Tetrapropylammonium Cation Leading to Stability Enhancement in Lead Halide Perovskite

Improving the performances of photovoltaic (PV) devices by suppressing nonradiative energy losses through surface defect passivation and enhancing the stability to the level of standard PV represents one critical challenge for perovskite solar cells. Here, reported are the advantages of introducing a tetrapropylammonium (TPA⁺) cation that combines two key functionalities, namely surface passivation of CH₃NH₃PbI₃ nanocrystals through strong ionic interaction with the surface and bulk passivation via formation of a type I heterostructure that acts as a recombination barrier. As a result, nonencapsulated perovskite devices with only 2 mol% of TPA⁺ achieve power conversion efficiencies over 18.5% with higher V_OC under air mass 1.5G conditions. The devices fabricated retain more than 85% of their initial performances for over 1500 h under ambient conditions (55% RH ± 5%). Furthermore, devices with TPA⁺ also exhibit excellent operational stability by retaining over 85% of the initial performance after 250 h at maximum power point under 1 sun illumination. The effect of incorporation of TPA⁺ on the structural and optoelectronic properties is studied by X‐ray diffraction, ultraviolet–visible absorption spectroscopy, ultraviolet photon–electron spectroscopy, time‐resolved photoluminescence, and scanning electron microscopy imaging. Atomic‐level passivation upon addition of TPA⁺ is elucidated employing 2D solid‐state NMR spectroscopy.     

High‐Performance Near‐IR Photodetector Using Low‐Bandgap MA0.5FA0.5Pb0.5Sn0.5I3 Perovskite

Photodetectors with ultrafast response are explored using inorganic/organic hybrid perovskites. High responsivity and fast optoelectronic response are achieved due to the exceptional semiconducting properties of perovskite materials. However, most of the perovskite‐based photodetectors exploited to date are centered on Pb‐based perovskites, which only afford spectral response across the visible spectrum. This study demonstrates a high‐performance near‐IR (NIR) photodetector using a stable low‐bandgap Sn‐containing perovskite, (CH₃NH₃)_0.5(NH₂CHNH₂)_0.5Pb_0.5Sn_0.5I₃ (MA_0.5FA_0.5Pb_0.5Sn_0.5I₃), which is processed with an antioxidant additive, ascorbic acid (AA). The addition of AA effectively strengthens the stability of Sn‐containing perovskite against oxygen, thereby significantly inhibiting the leakage current. Consequently, the derived photodetector shows high responsivity with a detectivity of over 10¹² Jones ranging from 800 to 970 nm. Such low‐cost, solution processable NIR photodetectors with high performance show promising potential for future optoelectronic applications.     

Efficient Ruddlesden–Popper Perovskite Light‐Emitting Diodes with Randomly Oriented Nanocrystals

Ruddlesden–Popper phase (RP‐phase) perovskites that consist of 2D perovskite slabs interleaved with bulky organic ammonium (OA) are favorable for light‐emitting diodes (LEDs). The critical limitation of LED applications is that the insulating OA arranged in a preferred orientation limits charge transport. Therefore, the ideal solution is to achieve a randomly connected structure that can improve charge transport without hampering the confinement of the electron–hole pair. Here, a structurally modulated RP‐phase metal halide perovskite (MHP), (PEA)₂(CH₃NH₃)_m?1Pb_mBr_3m+1 is introduced to make the randomly oriented RP‐phase unit and ensure good connection between them by applying modified nanocrystal pinning, which leads to an increase in the efficiency of perovskite LEDs (PeLEDs). The randomly connected RP‐phase MHP forces contact between inorganic layers and thereby yields efficient charge transport and radiative recombination. Combined with an optimal dimensionality, (PEA)₂(CH₃NH₃)₂Pb₃Br₁₀, the structurally modulated RP‐phase MHP exhibits increased photoluminescence quantum efficiency, from 0.35% to 30.3%, and their PeLEDs show a 2,018 times higher current efficiency (20.18 cd A^?1) than in the 2D PeLED (0.01 cd A^?1) and 673 times than in the 3D PeLED (0.03 cd A^?1) using the same film formation process. This approach provides insight on how to solve the limitation of RP‐phase MHP for efficient PeLEDs.     

Enhanced Incorporation of Guanidinium in Formamidinium‐Based Perovskites for Efficient and Stable Photovoltaics: The Role of Cs and Br

Recently, incorporating guanidium (GA) cations into organolead halide perovskites is shown to effectively improve the stability and performance of the solar cells. However, the underlying mechanisms that govern the GA incorporation have remained unclear. Here, FAPbI₃ is used as a basic framework to investigate experimentally and theoretically the role of cesium (Cs) and bromine (Br) substitutions in GA⁺ incorporation. It is found that simultaneous introduction of the small‐size Cs⁺ and Br^– in the FAPbI₃ lattice is critical to create sufficient space for the large GA⁺ and that the presence of the Cs⁺ prevents the formation of a GA‐contained low‐dimensional phase, which both assist GA⁺ incorporation. Upon entering the perovskite lattice, the GA⁺ can stabilize the lattice structure via forming strong hydrogen bonds with their neighboring halide ions. Such structure modification suppresses halide vacancy formation, thus leading to improved material properties. Compared to the GA‐free perovskite reference samples, the optimal system GA_0.05Cs_0.15FA_0.8Pb(I_0.85Br_0.15)₃ exhibits substantially improved thermal and photothermal stability, as well as increased photocarrier lifetime. Solar cells fabricated with the optimal material system show an excellent photovoltaic performance, with the champion device reaching a power conversion efficiency of 21.3% and an open circuit voltage of 1.229 V.     

Unveiling the Nanoparticle‐Seeded Catalytic Nucleation Kinetics of Perovskite Solar Cells by Time‐Resolved GIXS

Recently, a new seeding growth approach for perovskite thin films is reported to significantly enhance the device performance of perovskite solar cells. This work unveils the intermediate structures and the corresponding growth kinetics during conversion to perovskite crystal thin films assisted by seeding PbS nanocrystals (NCs), using time‐resolved grazing‐incidence X‐ray scattering. Through analyses of time‐resolved crystal formation kinetics obtained from synchrotron X‐rays with a fast subsecond probing time resolution, an important “catalytic” role of the seed‐like PbS NCs is clearly elucidated. The perovskite precursor‐capped PbS NCs are found to not only accelerate the nucleation of a highly oriented intermediate phase, but also catalyze the conversion of the intermediate phase into perovskite crystals with a reduced activation energy E_a = 47 (±5) kJ mol^?1, compared to 145 (±38) kJ mol^?1 for the pristine perovskite thin film. The reduced E_a is attributed to a designated crystal lattice alignment of the perovskite nanocrystals with perovskite cubic crystals; the pivotal heterointerface alignment of the perovskite crystals coordinated by the Pb NCs leads to an improved film surface morphology with less pinholes and enhanced crystal texture and thermal stability. These together contribute to the significantly improved photovoltaic performance of the corresponding devices.     

Constructing CsPbBr3 Cluster Passivated‐Triple Cation Perovskite for Highly Efficient and Operationally Stable Solar Cells

Ion migration and phase segregation, in mixed‐cation/anion perovskite materials, raises a bottleneck for its stability improvement in solar cells operation. Here, the synergetic effect of electric field and illumination on the phase segregation of Cs_0.05FA_0.80MA_0.15Pb(I_0.85Br_0.15)₃ (CsFAMA) perovskite is demonstrated. CsFAMA perovskite with a CsPbBr₃‐clusters passivated structure is realized, in which CsPbBr₃‐clusters are located at the surface/interface of CsFAMA grains. This structure is realized by introducing a CsPbBr₃ colloidal solution into the CsFAMA precursor. It is found that CsPbBr₃ passivation greatly suppresses phase segregation in CsFAMA perovskite. The resultant passivated CsFAMA also exhibits a longer photoluminescence lifetime due to reduced defect state densities, produces highly efficient TiO₂‐based planar solar cells with 20.6% power conversion efficiency and 1.195 V open‐circuit voltage. The optimized devices do not suffer from a fast burn‐in degradation and retain 90% of their initial performance at maximum power under one‐sun illumination at 25 °C (65 °C) exceeding 500 h (100 h) of continuous operation. This result represents the most stable output among CsFAMA solar cells in a planar structure with Spiro‐OMeTAD.     

Retarding Thermal Degradation in Hybrid Perovskites by Ionic Liquid Additives

Recent years have witnessed considerable progress in the development of solar cells based on lead halide perovskite materials. However, their intrinsic instability remains a limitation. In this context, the interplay between the thermal degradation and the hydrophobicity of perovskite materials is investigated. To this end, the salt 1‐(4‐ethenylbenzyl)‐3‐(3,3,4,4,5,5,6,6,7,7,8,8,8‐tridecafluorooctylimidazolium iodide (ETI), is employed as an additive in hybrid perovskites, endowing the photoactive materials with high thermal stability and hydrophobicity. The ETI additive inhibits methylammonium (MA) permeation in methylammonium lead triiodide (MAPbI₃) occurring due to intrinsic thermal degradation, by inhibiting out‐diffusion of the MA⁺ cation, preserving the pristine material and preventing decomposition. With this simple approach, high efficiency solar cells based on the unstable MAPbI₃ perovskite are markedly stabilized under maximum power point tracking, leading to greater than twice the preserved efficiency after 700 h of continuous light illumination and heating (60 °C). These results suggest a strategy to tackle the intrinsic thermal decomposition of MAI, an essential component in all state‐of‐the‐art perovskite compositions.     

Self‐Additive Low‐Dimensional Ruddlesden–Popper Perovskite by the Incorporation of Glycine Hydrochloride for High‐Performance and Stable Solar Cells

The recent rise of low‐dimensional Ruddlesden–Popper (RP) perovskites is notable for superior humidity stability, however they suffer from low power conversion efficiency (PCE). Suitable organic spacer cations with special properties display a critical effect on the performance and stability of perovskite solar cells (PSCs). Herein, a new strategy of designing self‐additive low‐dimensional RP perovskites is first proposed by employing a glycine salt (Gly⁺) with outstanding additive effect to improve the photovoltaic performance. Due to the strong interaction between C?O and Pb²⁺, the Gly⁺ can become a nucleation center and be beneficial to uniform and fast growth of the Gly‐based RP perovskites with larger grain sizes, leading to reduced grain boundary and increased carrier transport. As a result, the Gly‐based self‐additive low‐dimensional RP perovskites exhibit remarkable photoelectric properties, yielding the highest PCE of 18.06% for Gly (n = 8) devices and 15.61% for Gly (n = 4) devices with negligible hysteresis. Furthermore, the Gly‐based devices without encapsulation show excellent long‐term stability against humidity, heat, and UV light in comparison to BA‐based low‐dimensional PSCs. This approach provides a feasible design strategy of new‐type low‐dimensional RP perovskites to obtain highly efficient and stable devices for next‐generation photovoltaic applications.     

Controllable Perovskite Crystallization by Water Additive for High‐Performance Solar Cells

A key issue for perovskite solar cells is the stability of perovskite materials due to moisture effects under ambient conditions, although their efficiency is improved constantly. Herein, an improved CH₃NH₃PbI_3?xCl_x perovskite quality is demonstrated with good crystallization and stability by using water as an additive during crystal perovskite growth. Incorporating suitable water additives in N,N‐dimethylformamide (DMF) leads to controllable growth of perovskites due to the lower boiling point and the higher vapor pressure of water compared with DMF. In addition, CH₃NH₃PbI_3?xCl_x · nH₂O hydrated perovskites, which can be resistant to the corrosion by water molecules to some extent, are assumed to be generated during the annealing process. Accordingly, water additive based perovskite solar cells present a high power conversion efficiency of 16.06% and improved cell stability under ambient conditions compared with the references. The findings in this work provide a route to control the growth of crystal perovskites and a clue to improve the stability of organic–inorganic halide perovskites.     

Materials Discovery of Stable and Nontoxic Halide Perovskite Materials for High‐Efficiency Solar Cells

Two critical limitations of organic–inorganic lead halide perovskite materials for solar cells are their poor stability in humid environments and inclusion of toxic lead. In this study, high‐throughput density functional theory (DFT) methods are used to computationally model and screen 1845 halide perovskites in search of new materials without these limitations that are promising for solar cell applications. This study focuses on finding materials that are comprised of nontoxic elements, stable in a humid operating environment, and have an optimal bandgap for one of single junction, tandem Si‐perovskite, or quantum dot–based solar cells. Single junction materials are also screened on predicted single junction photovoltaic (PV) efficiencies exceeding 22.7%, which is the current highest reported PV efficiency for halide perovskites. Generally, these methods qualitatively reproduce the properties of known promising nontoxic halide perovskites that are either experimentally evaluated or predicted from theory. From a set of 1845 materials, 15 materials pass all screening criteria for single junction cell applications, 13 of which are not previously investigated, such as (CH₃NH₃)_0.75Cs_0.25SnI₃, ((NH₂)₂CH)Ag_0.5Sb_0.5Br₃, CsMn_0.875Fe_0.125I₃, ((CH₃)₂NH₂)Ag_0.5Bi_0.5I₃, and ((NH₂)₂CH)_0.5Rb_0.5SnI₃. These materials, together with others predicted in this study, may be promising candidate materials for stable, highly efficient, and nontoxic perovskite‐based solar cells.     

Achieving 20% Efficiency for Low‐Temperature‐Processed Inverted Perovskite Solar Cells

Low‐temperature‐processed inverted perovskite solar cells (PVSCs) attract increasing attention because they can be fabricated on both rigid and flexible substrates. For these devices, hole‐transporting layers (HTLs) play an important role in achieving efficient and stable inverted PVSCs by adjusting the anodic work function, hole extraction, and interfacial charge recombination. Here, the use of a low‐temperature (≤150 °C) solution‐processed ultrathin film of poly[(9,9‐dioctyl‐fluorenyl‐2,7‐diyl)‐co‐(4,4′‐(N‐(4‐secbutylphenyl) diphenylamine)] (TFB) is reported as an HTL in one‐step‐processed CH₃NH₃PbI₃ (MAPbI₃)‐based inverted PVSCs. The fabricated device exhibits power conversion efficiency (PCE) as high as 20.2% when measured under AM 1.5 G illumination. This PCE makes them one of the MAPbI₃‐based inverted PVSCs that have the highest efficiency reported to date. Moreover, this inverted PVSC also shows good stability, which can retain 90% of its original efficiency after 30 days of storage in ambient air.