High Lithium Ion Conductivity LiF/GO Solid Electrolyte Interphase Inhibiting the Shuttle of Lithium Polysulfides in Long‐Life Li–S Batteries

The “shuttle effect” that stems from the dissolution of polysulfides is the most fatal issue affecting the cycle life of lithium‐sulfur (Li–S) batteries. In order to suppress the “shuttle effect,” a new strategy of using a highly lithium ion conductive lithium fluoride/graphene oxide (LiF/GO) solid electrolyte interphase (SEI) to mechanically prevent the lithium dendrite breakthrough is reported. When utilized in Li–S batteries, the LiF/GO SEI coated separator demonstrates significant feature in mitigating the polysulfide shuttling as observed by in situ UV–vis spectroscopy. Moreover, the restrained “shuttle effect” can also be confirmed by analysis of electrochemical impedance spectroscopy and characterization of lithium dendrites, which indicates that no insulating layer of solid Li₂S₂/Li₂S is found on lithium anode surface. Furthermore, the LiF/GO SEI layer puts out good lithium ion conductivity as its lithium ion diffusion coefficient reaches a high value of 1.5 × 10^?7 cm² s^?1. These features enable a remarkable cyclic property of 0.043% of capacity decay per cycle during 400 cycles.     

Highly‐Cyclable Room‐Temperature Phosphorene Polymer Electrolyte Composites for Li Metal Batteries

Despite significant interest toward solid‐state electrolytes owing to their superior safety in comparison to liquid‐based electrolytes, sluggish ion diffusion and high interfacial resistance limit their application in durable and high‐power density batteries. Here, a novel quasi‐solid Li⁺ ion conductive nanocomposite polymer electrolyte containing black phosphorous (BP) nanosheets is reported. The developed electrolyte is successfully cycled against Li metal (over 550 h cycling) at 1 mA cm^?2 at room temperature. The cycling overpotential is dropped by 75% in comparison to BP‐free polymer composite electrolyte indicating lower interfacial resistance at the electrode/electrolyte interfaces. Molecular dynamics simulations reveal that the coordination number of Li⁺ ions around (trifluoromethanesulfonyl)imide (TFSI^?) pairs and ethylene‐oxide chains decreases at the Li metal/electrolyte interface, which facilitates the Li⁺ transport through the polymer host. Density functional theory calculations confirm that the adsorption of the LiTFSI molecules at the BP surface leads to the weakening of N and Li atomic bonding and enhances the dissociation of Li⁺ ions. This work offers a new potential mechanism to tune the bulk and interfacial ionic conductivity of solid‐state electrolytes that may lead to a new generation of lithium polymer batteries with high ionic conduction kinetics and stable long‐life cycling.     

Constructing a High‐Strength Solid Electrolyte Layer by In Vivo Alloying with Aluminum for an Ultrahigh‐Rate Lithium Metal Anode

The serious safety issues caused by uncontrollable lithium (Li) dendrite growth, especially at high current densities, seriously hamper the rapid charging of Li metal‐based batteries. Here, the construction of Al–Li alloy/LiCl‐based Li anode (ALA/Li anode) is reported by displacement and alloying reaction between an AlCl₃‐ionic liquid and a Li foil. This layer not only has high ion‐conductivity and good electron resistivity but also much improved mechanical strength (776 MPa) as well as good flexibility compared to a common solid electrolyte interphase layer (585 MPa). The high mechanical strength of the Al–Li alloy interlayer effectively eliminates volume expansion and dendrite growth in Li metal batteries, so that the ALA/Li anode achieves superior cycling for 1600 h (2.0 mA cm^?2) and 1000 cycles at an ultrahigh current density (20 mA cm^?2) without dendrite formation in symmetric batteries. In lithium–sulfur batteries, the dense alloy layer prevents direct contact between polysulfides and Li metal, inhibiting the shuttle effect and electrolyte decomposition. Long cycling performance is achieved even at a high current density (4 C) and a low electrolyte/sulfur (6.0 µL mg^?1). This easy fabrication process provides a strategy to realize reliable safety during the rapid charging of Li‐metal batteries.     

Hexafluoroisopropyl Trifluoromethanesulfonate-Driven Easily Li+ Desolvated Electrolyte to Afford Li||NCM811 Cells with Efficient Anode/Cathode Electrolyte Interphases

Solid electrolyte interphase (SEI) and cathode electrolyte interphase (CEI) with optimized components and structures are considered to be crucial for lithium-ion batteries. Here, gradient lithium oxysulfide (Li₂SO_x, x = 0, 3, 4)/uniform lithium fluoride (LiF)-type SEI is designed in situ by using hexafluoroisopropyl trifluoromethanesulfonate (HFPTf) as electrolyte additive. HFPTf is more likely to be reduced on the surface of Li anode in electrolytes due to its high reduction potential. Moreover, HFPTf can make Li⁺ desolvated easily, leading to the increase in the flux of Li⁺ on the surface of Li anode to avoid the growth of Li dendrites. Thus, the cycling stability of Li||Li symmetric cells is improved to be 1000 h at 0.5 mA cm⁻². In addition, HFPTf-contained electrolyte could make Li||NCM811 batteries with a capacity retention of 70% after 150 cycles at 100 mA g⁻¹, which is attributed to the formation of uniform and stable CEI on the cathode surface for hindering the dissolvation of metal ions from the cathode. This study provides effective insights on the strong ability of additives to adjust electrolytes in “one phase and two interphases” (electrolyte and SEI/CEI).     

Hydrofluoric Acid-Removable Additive Optimizing Electrode Electrolyte Interphases with Li+ Conductive Moieties for 4.5 V Lithium Metal Batteries

High-voltage lithium metal batteries (LMBs) are capable to achieve the increasing energy density. However, their cycling life is seriously affected by unstable electrolyte/electrode interfaces and capacity instability at high voltage. Herein, a hydrofluoric acid (HF)-removable additive is proposed to optimize electrode electrolyte interphases for addressing the above issues. N, N-dimethyl-4-(4,4,5,5-tetramethyl-1,3,2-dioxaborolan-2-yl) aniline (DMPATMB) is used as the electrolyte additive to induce PF₆⁻ decomposition to form a dense and robust LiF-rich solid electrolyte interphase (SEI) for suppressing Li dendrite growth. Moreover, DMPATMB can help to form highly Li⁺ conductive Li₃N and LiBO₂, which can boost the Li⁺ transport across SEI and cathode electrolyte interphase (CEI). In addition, DMPATMB can scavenge traced HF in the electrolyte to protect both SEI and CEI from the corrosion. As expected, 4.5 V Li|| LiNi_0.6Co_0.2Mn_0.2O₂ batteries with such electrolyte deliver 145 mAh g⁻¹ after 140 cycles at 200 mA g⁻¹. This work provides a novel insight into high-voltage electrolyte additives for LMBs.     

Effect of the Anion Activity on the Stability of Li Metal Anodes in Lithium‐Sulfur Batteries

With the significant progress made in the development of cathodes in lithium‐sulfur (Li‐S) batteries, the stability of Li metal anodes becomes a more urgent challenge in these batteries. Here the systematic investigation of the stability of the anode/electrolyte interface in Li‐S batteries with concentrated electrolytes containing various lithium salts is reported. It is found that Li‐S batteries using LiTFSI‐based electrolytes are more stable than those using LiFSI‐based electrolytes. The decreased stability is because the N–S bond in the FSI^? anion is fairly weak and the scission of this bond leads to the formation of lithium sulfate (LiSO_x) in the presence of polysulfide species. In contrast, in the LiTFSI‐based electrolyte, the lithium metal anode tends to react with polysulfide to form lithium sulfide (LiS_x), which is more reversible than LiSO_x formed in the LiFSI‐based electrolyte. This fundamental difference in the bond strength of the salt anions in the presence of polysulfide species leads to a large difference in the stability of the anode‐electrolyte interface and performance of the Li‐S batteries with electrolytes composed of these salts. Therefore, anion selection is one of the key parameters in the search for new electrolytes for stable operation of Li‐S batteries.     

Intrinsic Lithiophilicity of Li–Garnet Electrolytes Enabling High‐Rate Lithium Cycling

Solid‐state lithium batteries are widely considered as next‐generation lithium‐ion battery technology due to the potential advantages in safety and performance. Among the various solid electrolyte materials, Li–garnet electrolytes are promising due to their high ionic conductivity and good chemical and electrochemical stabilities. However, the high electrode/electrolyte interfacial impedance is one of the major challenges. Moreover, short circuiting caused by lithium dendrite formation is reported when using Li–garnet electrolytes. Here, it is demonstrated that Li–garnet electrolytes wet well with lithium metal by removing the intrinsic impurity layer on the surface of the lithium metal. The Li/garnet interfacial impedance is determined to be 6.95 Ω cm² at room temperature. Lithium symmetric cells based on the Li–garnet electrolytes are cycled at room temperature for 950 h and current density as high as 13.3 mA cm^?2 without showing signs of short circuiting. Experimental and computational results reveal that it is the surface oxide layer on the lithium metal together with the garnet surface that majorly determines the Li/garnet interfacial property. These findings suggest that removing the superficial impurity layer on the lithium metal can enhance the wettability, which may impact the manufacturing process of future high energy density garnet‐based solid‐state lithium batteries.     

In Situ Formation of Li3P Layer Enables Fast Li+ Conduction across Li/Solid Polymer Electrolyte Interface

Solid‐state polymer electrolytes provide better flexibility and electrode contact than their ceramic counterparts, making them a worthwhile pursuit for all‐solid‐state lithium‐metal batteries. However, their large Li/solid state electrolyte interfacial resistance, small critical current density, and rapid lithium dendrite growth during cycling still limit their viability. Owing to these restrictions, all‐solid‐state cells with solid polymer electrolytes must be cycled above room‐temperature and with a small current density. These problems can be mitigated with an in situ formed artificial solid electrolyte interphase that rapidly conducts Li⁺ ions. Herein, a Li₃P layer formed in situ at the Li‐metal/solid polymer electrolyte interphase is reported that significantly reduces the electrode/electrolyte interfacial resistance. Additionally, this layer increases the wettability of the solid polymer by the metallic lithium anode, allowing for the critical current density of lithium symmetric cells to be doubled by homogenizing the current density at the interface. All‐solid‐state Li/Li symmetric cells and Li/LiFePO₄ cells with the Li₃P layer show improved cycling performance with a high current density.     

Enhanced Cycling Stability of Rechargeable Li–O2 Batteries Using High‐Concentration Electrolytes

The stability of electrolytes against highly reactive, reduced oxygen species is crucial for the development of rechargeable Li–O₂ batteries. In this work, the effect of lithium salt concentration in 1,2‐dimethoxyethane (DME)‐based electrolytes on the cycling stability of Li–O₂ batteries is investigated systematically. Cells with highly concentrated electrolyte demonstrate greatly enhanced cycling stability under both full discharge/charge (2.0–4.5 V vs Li/Li⁺) and the capacity‐limited (at 1000 mAh g^?1) conditions. These cells also exhibit much less reaction residue on the charged air‐electrode surface and much less corrosion of the Li‐metal anode. Density functional theory calculations are used to calculate molecular orbital energies of the electrolyte components and Gibbs activation energy barriers for the superoxide radical anion in the DME solvent and Li⁺–(DME) _n solvates. In a highly concentrated electrolyte, all DME molecules are coordinated with salt cations, and the C–H bond scission of the DME molecule becomes more difficult. Therefore, the decomposition of the highly concentrated electrolyte can be mitigated, and both air cathodes and Li‐metal anodes exhibit much better reversibility, resulting in improved cyclability of Li–O₂ batteries.     

High‐Power Lithium Metal Batteries Enabled by High‐Concentration Acetonitrile‐Based Electrolytes with Vinylene Carbonate Additive

To enable next‐generation high‐power, high‐energy‐density lithium (Li) metal batteries (LMBs), an electrolyte possessing both high Li Coulombic efficiency (CE) at a high rate and good anodic stability on cathodes is critical. Acetonitrile (AN) is a well‐known organic solvent for high anodic stability and high ionic conductivity, yet its application in LMBs is limited due to its poor compatibility with Li metal anodes even at high salt concentration conditions. Here, a highly concentrated AN‐based electrolyte is developed with a vinylene carbonate (VC) additive to suppress Li⁺ depletion at high current densities. Addition of VC to the AN‐based electrolyte leads to the formation of a polycarbonate‐based solid electrolyte interphase, which minimizes Li corrosion and leads to a very high Li CE of up to 99.2% at a current density of 0.2 mA cm^‐2. Using such an electrolyte, fast charging of Li||NMC333 cells is realized at a high current density of 3.6 mA cm^‐2, and stable cycling of Li||NMC622 cells with a high cathode loading of 4 mAh cm^‐2 is also demonstrated.     

Sulfurized Polyacrylonitrile Cathodes with High Compatibility in Both Ether and Carbonate Electrolytes for Ultrastable Lithium–Sulfur Batteries

Sulfurized polyacrylonitrile (SPAN) is a promising material capable of suppressing polysulfide dissolution in lithium–sulfur (Li–S) batteries with carbonate electrolyte. However, undesirable spontaneous formation of soluble polysulfides may arise in the ether electrolyte, and the conversion of sulfur in SPAN during the lithiation/delithiation processes is yet to be understood. Here, a highly reliable Li–S system using a freestanding fibrous SPAN cathode, as well as the sulfur conversion mechanism involved, is demonstrated. The SPAN shows high compatibility in both ether and carbonate electrolytes. The sulfur atoms existing in the form of short ? S₂? and ? S₃? chains are covalently bonded to the pyrolyzed PAN backbone. The electrochemical reduction of the SPAN by Li⁺ is a single‐phase solid–solid reaction with Li₂S as the sole discharge product. Meanwhile, the parasitic reaction between Li⁺ and C?N bonds exists upon the first discharge, and the residual Li⁺ enhances the conductivity of the backbone. The recharge ability and rate capability are kinetically dominated by the activation of Li₂S nanoflakes generated during discharge. At 800 mA g^?1, a specific capacity of 1180 mAh g^?1 is realized without capacity fading in the measured 1000 cycles, which makes SPAN promising for practical application.     

Building Artificial Solid‐Electrolyte Interphase with Uniform Intermolecular Ionic Bonds toward Dendrite‐Free Lithium Metal Anodes

Li metal has been widely regarded as a promising anode for next‐generation batteries due to its high theoretical capacity and low electrochemical potential. The unstable solid‐electrolyte interphase (SEI) and uncontrollable dendrite growth, however, incur severe safety hazards and hamper the practical application of Li metal anodes. Herein, an advanced artificial SEI layer constructed by [LiNBH]_n chains, which are crosslinked and self‐reinforced by their intermolecular Li? N ionic bonds, is designed to comprehensively stabilize Li metal anodes on a molecular level. Benefiting from its polymer‐like structure, the [LiNBH]_n layer is flexible and effectively tolerates the volume change of Li metal anodes. In addition, this layer with high polarity in its structure, helps to regulate the homogeneous distribution of the Li⁺ flux on Li electrodes via the further formation of Li? N bonds. The designed [LiNBH]_n layer is electrically nonconductive but highly ionically conductive, thus facilitating Li⁺ diffusion and confining Li deposition beneath the layer. Therefore, under the protection of the [LiNBH]_n layer, the Li metal anodes exhibit stable cycling at a 3 mA cm^?2 for more than 700 h, and the full cells with high lithium iron phosphate and sulfur cathodes mass loading also present excellent cycling stability.     

Intercalated Electrolyte with High Transference Number for Dendrite‐Free Solid‐State Lithium Batteries

Solid‐state lithium (Li) batteries using solid electrolytes and Li anodes are highly desirable because of their high energy densities and intrinsic safety. However, low ambient‐temperature conductivity and poor interface compatibility of solid electrolytes as well as Li dendrite formation cause large polarization and poor cycling stability. Herein, a high transference number intercalated composite solid electrolyte (CSE) is prepared by the combination of a solution‐casting and hot‐pressing method using layered lithium montmorillonite, poly(ethylene carbonate), lithium bis(fluorosulfonyl)imide, high‐voltage fluoroethylene carbonate additive, and poly(tetrafluoroethylene) binder. The electrolyte presents high ionic conductivity (3.5 × 10^?4 S cm^?1), a wide electrochemical window (4.6 V vs Li⁺/Li), and high ionic transference number (0.83) at 25 °C. In addition, a 3D Li anode is also fabricated via a facile thermal infusion strategy. The synergistic effect of high transference number intercalated electrolyte and 3D Li anode is more favorable to suppress Li dendrites in a working battery. The solid‐state batteries based on LiFePO₄ (Al₂O₃ @ LiNi_0.5Co_0.2Mn_0.3O₂), CSE, and 3D Li deliver admirable cycling stability with discharge capacity 145.9 mAh g^?1 (150.7 mAh g^?1) and capacity retention 91.9% after 200 cycles at 0.5 C (92.0% after 100 cycles at 0.2 C) at 25 °C. This work affords a splendid strategy for high‐performance solid‐state battery.     

Dynamic Ion Sieve as the Buffer Layer for Regulating Li+ Flow in Lithium Metal Batteries

How to realize uniform Li⁺ flow is the key to achieve even Li deposition for lithium metal batteries (LMBs). In this study, a concept of dynamic ion sieve is proposed to design the buffer layer nearby Li anode surface to regulate Li⁺ spatial arrangement by introducing tributylmethylphosphonium bis(trifluoromethanesulfonyl)imide (TMPB) into the carbonate electrolyte. The buffer layer induced by TMP⁺ can adjust the velocity of arriving solvated Li⁺ that gives solvated Li⁺ sufficient time to redistribute and accumulate on Li anode surface, resulting in a uniform and higher concentrated Li⁺ flow. Besides, TFSI⁻ can participate in the generation of inorganic component-rich solid electrolyte interphase (SEI) with Li₃N, which can facilitate the Li⁺ conductivity of SEI. Consequently, the stable and uniform Li deposition can be obtained, achieving the excellent cycling performance up to 1000 h at 0.5 mA cm⁻² in the Li||Li symmetric cell. Besides, the Li||NCM622 full cell also possesses excellent cycling stability with a high-capacity retention rate of 66.7% after 300 cycles.     

A High‐Performance Li–B–H Electrolyte for All‐Solid‐State Li Batteries

Highly Li‐ion conductive Li₄(BH₄)₃I@SBA‐15 is synthesized by confining the LiI doped LiBH₄ into mesoporous silica SBA‐15. Uniform nanoconfinement of P6₃ mc phase Li₄(BH₄)₃I in SBA‐15 mesopores leads to a significantly enhanced conductivity of 2.5 × 10^?4 S cm^?1 with a Li‐ion transference number of 0.97 at 35 °C. The super Li‐ion mobility in the interface layer with a thickness of 1.2 nm between Li₄(BH₄)₃I and SBA‐15 is believed to be responsible for the fast Li‐ion conduction in Li₄(BH₄)₃I@SBA‐15. Additionally, Li₄(BH₄)₃I@SBA‐15 also exhibits a wide apparent electrochemical stability window (0 to 5 V vs Li/Li⁺) and a superior Li dendrite suppression capability (critical current density 2.6 mA cm^?2 at 55 °C) due to the formation of stable interphases. More importantly, Li₄(BH₄)₃I@SBA‐15‐based Li batteries using either high‐capacity sulfur cathode or high‐voltage oxide cathode show excellent electrochemical performances, making Li₄(BH₄)₃I@SBA‐15 a very attractive electrolyte for next‐generation all‐solid‐state Li batteries.     

Porosity‐ and Graphitization‐Controlled Fabrication of Nanoporous Silicon@Carbon for Lithium Storage and Its Conjugation with MXene for Lithium‐Metal Anode

Silicon (Si) and lithium metal are the most favorable anodes for high‐energy‐density lithium‐based batteries. However, large volume expansion and low electrical conductivity restrict commercialization of Si anodes, while dendrite formation prohibits the applications of lithium‐metal anodes. Here, uniform nanoporous Si@carbon (NPSi@C) from commercial alloy and CO₂ is fabricated and tested as a stable anode for lithium‐ion batteries (LIBs). The porosity of Si as well as graphitization degree and thickness of the carbon layer can be controlled by adjusting reaction conditions. The rationally designed porosity and carbon layer of NPSi@C can improve electronic conductivity and buffer volume change of Si without destroying the carbon layer or disrupting the solid electrolyte interface layer. The optimized NPSi@C anode shows a stable cyclability with 0.00685% capacity decay per cycle at 5 A g^?1 over 2000 cycles for LIBs. The energy storage mechanism is explored by quantitative kinetics analysis and proven to be a capacitance‐battery dual model. Moreover, a novel 2D/3D structure is designed by combining MXene and NPSi@C. As lithiophilic nucleation seeds, NPSi@C can induce uniform Li deposition with buffered volume expansion, which is proven by exploring Li‐metal deposition morphology on Cu foil and MXene@NPSi@C. The practical potential application of NPSi@C and MXene@NPSi@C is evaluated by full cell tests with a Li(Ni_0.8Co_0.1Mn_0.1)O₂ cathode.     

A Lithium‐Sulfur Battery with a High Areal Energy Density

The battery community has recently witnessed a considerable progress in the cycle lives of lithium‐sulfur (Li‐S) batteries, mostly by developing the electrode structures that mitigate fatal dissolution of lithium polysulfides. Nonetheless, most of the previous successful demonstrations have been based on limited areal capacities. For realistic battery applications, however, the chronic issues from both the anode (lithium dendrite growth) and the cathode (lithium polysulfide dissolution) need to be readdressed under much higher loading of sulfur active material. To this end, the current study integrates the following three approaches in a systematic manner: 1) the sulfur electrode material with diminished lithium polysulfide dissolution by the covalently bonded sulfur‐carbon microstructure, 2) mussel‐inspired polydopamine coating onto the separator that suppresses lithium dendrite growth by wet‐adhesion between the separator and Li metal, and 3) addition of cesium ions (Cs⁺) to the electrolyte to repel incoming Li ions and thus prevent Li dendrite growth. This combined strategy resolves the long‐standing problems from both electrodes even under the very large sulfur‐carbon composite loading of 17 mg cm^?2 in the sulfur electrode, enabling the highest areal capacity (9 mAh cm^?2) to date while preserving stable cycling performance.     

Electrolytes Enriched by Crown Ethers for Lithium Metal Batteries

Lithium (Li) metal battery is considered the most promising next-generation battery due to its low potential and high theoretical capacity. However, Li dendrite growth causes serious safety problems. Herein, the 15-Crown-5 (15-C-5) is reported as an electrolyte additive based on solvation shell regulation. The strong complex effect between Li⁺ ion and 15-C-5 can reduce the concentration of Li ions on the electrode surface, thus changing the nucleation, and repressing the growth of Li dendrites in the plating process. Significantly, the strong coordination of Li⁺/15-C-5 would be able to make them aggregate around the Li crystal surface, which could form a protective layer and favor the formation of a smooth and dense solid electrolyte interphase with high toughness and Li⁺ ion conductivity. Therefore, the electrolyte system with 2.0 wt% 15-C-5 achieves excellent electrochemical performance with 170 cycles at 1.0 mA cm⁻² with capacity of 0.5 mA h cm⁻² in symmetric Li|Li cells. The obviously enhanced cycle and rate performance are also achieved in Li|LiNi_0.6Co_0.2Mn_0.2O₂ (NCM622) full cells. The 15-C-5 demonstrates to be a promising additive for the electrolytes toward safe and efficient Li metal batteries.     

Stabilizing Solid Electrolyte Interphases on Both Anode and Cathode for High Areal Capacity,High‐Voltage Lithium Metal Batteries with High Li Utilization and Lean Electrolyte

High‐energy‐density lithium metal batteries are considered the most promising candidates for the next‐generation energy storage systems. However, conventional electrolytes used in lithium‐ion batteries can hardly meet the demand of the lithium metal batteries due to their intrinsic instability for Li metal anodes and high‐voltage cathodes. Herein, an ester‐based electrolyte with tris(trimethylsilyl)phosphate additive that can form stable solid electrolyte interphases on the anode and cathode is reported. The additive decomposes before the ester solvent and enables the formation of P‐ and Si‐rich interphases on both electrodes that are ion conductive and robust. Thus, lithium metal batteries with a high‐specific‐energy of 373 Wh kg^?1 can exhibit a long lifespan of over 80 cycles under practical conditions, including a low negative/positive capacity ratio of 2.3, high areal capacity of 4.5 mAh cm^?2 for cathode, high‐voltage of 4.5 V, and lean electrolyte of 2.8 µL mAh^?1. A 4.5 V pouch cell is further assembled to demonstrate the practical application of the tris(trimethylsilyl)phosphate additive with an areal capacity of 10.2 and 9.4 mAh cm^?2 for the anode and cathode, respectively. This work is expected to provide an effective electrolyte optimizing strategy compatible with current lithium ion battery manufacturing systems and pave the way for the next‐generation Li metal batteries with high specific energy and energy density.     

A Mixed Lithium‐Ion Conductive Li2S/Li2Se Protection Layer for Stable Lithium Metal Anode

Constructing artificial solid‐electrolyte interphase (SEI) on the surface of Li metal is an effective approach to improve ionic conductivity of surface SEI and buffer Li dendrite growth of Li metal anode. However, constructing of homogenous ideal artificial SEI is still a great challenge. Here, a mixed lithium‐ion conductive Li₂S/Li₂Se (denoted as LSSe) protection layer, fabricated by a facile and inexpensive gas–solid reaction, is employed to construct stable surface SEI with high ionic conductivity. The Li₂S/Li₂Se‐protected Li metal (denoted as LSSe@Li) exhibits a stable dendrite‐free cycling behavior over 900 h with a high lithium stripping/plating capacity of 3 mAh cm^?2 at 1.5 mA cm^?2 in the symmetrical cell. Compared to bare Li anode, full batteries paired with LiFePO₄, sulfur/carbon, and LiNi_0.6Co_0.2Mn_0.2O₂ cathodes all present better battery cycling and rate performance when LSSe@Li anode is used. Moreover, Li₂Se exhibits a lower lithium‐ion migration energy barrier in comparison with Li₂S which is proved by density functional theory calculation.