Fast and Controllable Electric‐Field‐Assisted Reactive Deposited Stable and Annealing‐Free Perovskite toward Applicable High‐Performance Solar Cells

Recently, organic–inorganic hybrid perovskite materials have drawn great attention for their outstanding performance in high‐efficiency solar cells. Successful synthesis has been realized either in solution‐based chemical deposition or vapor deposition. However, conflicts have never ceased among quality control, growth rate, process complexity, and instrument requirement, which have limited their development toward real applications. In this work, the first electrochemical fabrication of perovskite toward high‐efficiency and scalable perovskite solar cells (PSCs) is established. The morphology and crystallization of the CH₃NH₃PbI₃ film can be effectively controlled by simply modulating a few physical parameters. A detailed study on its optoelectronic properties reveals significantly improved film quality and interfacial conditions. Aided by this, the total process does not require standard annealing, which greatly reduces the total growth time from hours to minutes. Up to now, an efficiency of 15.65% has been achieved in planar PSCs under 1 sun AM 1.5 condition, with small hysteresis and efficiency loss under longtime exposure to air. Moreover, high efficiency (10.45%) can be easily attained for large cells (2 cm²). This result will hopefully facilitate research for applicable high‐efficiency PSCs and other multicomponent materials as well.     

Direct Threat of a UV‐Ozone Treated Indium‐Tin‐Oxide Substrate to the Stabilities of Common Organic Semiconductors

Ultraviolet‐ozone treated indium‐tin‐oxide (UV‐ITO) glass substrates have been widely and unquestioningly used in the field of organic electronics to improve both device performance and stability. Evidence is presented here for rapid decay of common organic films such as N,N′‐bis(naphthalen‐1‐ yl)‐N,N′‐bis(phenyl)‐benzidine (NPB), tris(8‐hydroxy‐quinolinato)aluminum (Alq₃), and rubrene when they are in contact with an UV‐ITO substrate. While the photoluminescence (PL) of these organic films deposited on an UV‐ITO substrate decay rapidly under illumination; those on quartz substrates are comparatively much more stable. Results from X‐ray and UV photoemission spectroscopies (XPS and UPS) further suggest that degradations of the rubrene films on UV‐ITO substrate are mainly attributed to active oxygen species generated upon UV‐ozone treatment. These reactive oxygen species on the UV‐ITO surface behave as a reservoir of oxygen that interacts with rubrene and shifts its highest occupied molecular orbital (HOMO) level away from the Fermi level. This interaction induces a gap‐state in the energy gap of rubrene, which acts as a charge recombination center. More importantly, enhanced stabilities of rubrene‐based organic photovoltaic (OPV) devices are demonstrated when they are fabricated on gold‐coated or trifluoromethane (CHF₃) plasma‐treated ITO. The presented works shows that the commonly used UV‐ITO substrate is a threat to the stability of addlayer organic semiconducting films.     

Fluidic Processing of High‐Performance ZIF‐8 Membranes on Polymeric Hollow Fibers: Mechanistic Insights and Microstructure Control

Recently, a methodology for fabricating polycrystalline metal‐organic framework (MOF) membranes has been introduced – referred to as interfacial microfluidic membrane processing – which allows parallelizable fabrication of MOF membranes inside polymeric hollow fibers of microscopic diameter. Such hollow fiber membranes, when bundled together into modules, are an attractive way to scale molecular sieving membranes. The understanding and engineering of fluidic processing techniques for MOF membrane fabrication are in their infancy. Here, a detailed mechanistic understanding of MOF (ZIF‐8) membrane growth under microfluidic conditions in polyamide‐imide hollow fibers is reported, without any intermediate steps (such as seeding or surface modification) or post‐synthesis treatments. A key finding is that interfacial membrane formation in the hollow fiber occurs via an initial formation of two distinct layers and the subsequent rearrangement into a single layer. This understanding is used to show how nonisothermal processing allows fabrication of thinner (5 μm) ZIF‐8 films for higher throughput, and furthermore how engineering the polymeric hollow fiber support microstructure allows control of defects in the ZIF‐8 membranes. The performance of these engineered ZIF‐8 membranes is then characterized, which have H₂/C₃H₈ and C₃H₆/C₃H₈ mixture separation factors as high as 2018 and 65, respectively, and C₃H₆ permeances as high as 66 GPU.     

Novel Ω‐Shaped Core–Shell Photodetector with High Ultraviolet Selectivity and Enhanced Responsivity

The design of nanostructure plays an important role in performance enhancement of low‐dimensional optoelectronic devices. Herein, a novel photodetector (PD) based on electrospun SnO₂ nanofibers with Ω‐shaped ZnO shell (SnO₂@ZnO) is fabricated. With 87.4% transmittance at 550 nm, SnO₂@ZnO PD exhibits a high photo‐to‐dark current ratio up to 10⁴ at around 280 nm. Owing to the additional Ω‐shaped ZnO shell, SnO₂@ZnO PD possesses a responsivity of nearly 100 A W^?1 under 5 V bias and the illumination of 250 nm light, which is 30‐time enhancement of pristine SnO₂ PD. The enhancement is mainly attributed to type‐II energy band structure. Furthermore, by changing the direction of incident light, SnO₂@ZnO PD has a high UV selectivity with an UV–vis rejection ratio (R _{250 nm}/R _{400 nm}) as much as 2.0 × 10³ at 5 V bias under back illumination, which is fourfold higher than that under face illumination. The UV selectivity improvement may be attributed to light confinement in the Ω‐shaped structure. With both theoretical simulations and experimental comparisons, it is demonstrated that the unique compact Ω‐shaped nanostructure does contribute to photon trapping and gaining process, especially in back‐illumination configuration. The approach can be easily extended to other materials, preparing novel building blocks for optoelectronic devices.     

An Alternative Route Towards Metal–Polymer Hybrid Materials Prepared by Vapor‐Phase Processing

Transition metals incorporated into polymers lead to unusual or improved physical properties that significantly differ from those of purely organic polymers. A simple and practicable incorporation of diverse transition metals into any available polymer would make an important contribution to overcome some of the synthetic difficulties of metal‐polymer hybrid materials. Here, it is demonstrated that atomic layer deposition (ALD) can be a promising means to resolve some of those difficulties. It is found that even polytetrafluoroethylene (PTFE) with its great physical and chemical stability can be easily transformed into a transition metal–PTFE hybrid material simply by applying a metal‐oxide ALD process to PTFE. Upon metal incorporation into the PTFE, the molecular structure as well as mechanical properties (tensile behavior) of PTFE were observed to significantly change. For a better understanding of the changes to the material, experimental investigations using Raman spectroscopy, attenuated‐total‐reflection Fourier‐transform infrared spectroscopy, wide‐angle X‐ray diffraction, and energy‐dispersive X‐ray analysis were performed. In addition, with density functional theory calculations, potential bonding states of the incorporated metal into PTFE were modeled and predicted. The ALD‐based vapor‐phase approach for metal incorporation into a polymer could bring about rapid progress in the research area of metal–polymer hybrid materials.     

Enhanced Light‐Harvesting and Photocatalytic Properties in Morph‐TiO2 from Green‐Leaf Biotemplates

The unique structure of green leaves endows them with an extremely high light‐harvesting efficiency. In this work, green leaves are applied as biotemplates to synthesize morph‐TiO₂. The structural features favorable for light harvesting from the macro‐ to the nanoscale are replicated in morph‐TiO₂ through a two‐step infiltration process and the N contained in the original leaves is self‐doped into the resulting samples. The absorbance intensities within the visible‐light range of morph‐TiO₂ derived from different leaves increase by 103–258% and the band‐gap‐absorption onsets at the edge of the UV and visible‐light range show a red‐shift of 25–100 nm compared to those in TiO₂ without the template. The photocatalytic activity of morph‐TiO₂ is also improved, as proven by an electron paramagnetic resonance (EPR) study and degradation of rhodamine dye under irradiation with UV and visible light. The present work, as a new strategy, is of far‐reaching significance in learning from nature, driving us to make full use of the most‐abundant resources and structure‐introduced functions endowed by nature, opening up possibilities for extensive study of the physical and chemical properties of morph‐structured oxides and extending their potential for use in applications such as solar cells, photocatalysts, photoelectrical devices, and photoinduced sensors.     

Enhanced Performance of I2‐Free Solid‐State Dye‐Sensitized Solar Cells with Conductive Polymer up to 6.8%

An iodine‐free solid‐state dye‐sensitized solar cell (ssDSSC) is reported here, with 6.8% energy conversion efficiency—one of the highest yet reported for N719 dye—as a result of enhanced light harvesting from the increased transmittance of an organized mesoporous TiO₂ interfacial layer and the good hole conductivity of the solid‐state‐polymerized material. The organized mesoporous TiO₂ (OM‐TiO₂) interfacial layer is prepared on large‐area substrates by a sol‐gel process, and is confirmed by scanning electron microscopy (SEM) and grazing incidence small‐angle X‐ray scattering (GISAXS). A 550‐nm‐thick OM‐TiO₂ film coated on fluorine‐doped tin oxide (FTO) glass is highly transparent, resulting in transmittance increases of 8 and 4% compared to those of the bare FTO and conventional compact TiO₂ film on FTO, respectively. The high cell performance is achieved through careful control of the electrode/hole transport material (HTM) and nanocrystalline TiO₂/conductive glass interfaces, which affect the interfacial resistance of the cell. Furthermore, the transparent OM‐TiO₂ film, with its high porosity and good connectivity, exhibits improved cell performance due to increased transmittance in the visible light region, decreased interfacial resistance ( Ω ), and enhanced electron lifetime ( τ ). The cell performance also depends on the conductivity of HTMs, which indicates that both highly conductive HTM and the transparent OM‐TiO₂ film interface are crucial for obtaining high‐energy conversion efficiencies in I₂‐free ssDSSCs.     

Positively K+‐Responsive Membranes with Functional Gates Driven by Host–Guest Molecular Recognition

A novel positively K⁺‐responsive membrane with functional gates driven by host‐guest molecular recognition is prepared by grafting poly(N‐isopropylacrylamide‐co‐acryloylamidobenzo‐15‐crown‐5) (poly(NIPAM‐co‐AAB₁₅C₅)) copolymer chains in the pores of porous nylon‐6 membranes with a two‐step method combining plasma‐induced pore‐filling grafting polymerization and chemical modification. Due to the cooperative interaction of host‐guest complexation and phase transition of the poly(NIPAM‐co‐AAB₁₅C₅), the grafted gates in the membrane pores could spontaneously switch from “closed” state to “open” state by recognizing K⁺ ions in the environment and vice versa; while other ions (e.g., Na⁺, Ca²⁺ or Mg²⁺) can not trigger such an ion‐responsive switching function. The positively K⁺‐responsive gating action of the membrane is rapid, reversible, and reproducible. The proposed K⁺‐responsive gating membrane provide a new mode of behavior for ion‐recognizable “smart” or “intelligent” membrane actuators, which is highly attractive for controlled release, chemical/biomedical separations, tissue engineering, sensors, etc.     

Achieving 20% Efficiency for Low‐Temperature‐Processed Inverted Perovskite Solar Cells

Low‐temperature‐processed inverted perovskite solar cells (PVSCs) attract increasing attention because they can be fabricated on both rigid and flexible substrates. For these devices, hole‐transporting layers (HTLs) play an important role in achieving efficient and stable inverted PVSCs by adjusting the anodic work function, hole extraction, and interfacial charge recombination. Here, the use of a low‐temperature (≤150 °C) solution‐processed ultrathin film of poly[(9,9‐dioctyl‐fluorenyl‐2,7‐diyl)‐co‐(4,4′‐(N‐(4‐secbutylphenyl) diphenylamine)] (TFB) is reported as an HTL in one‐step‐processed CH₃NH₃PbI₃ (MAPbI₃)‐based inverted PVSCs. The fabricated device exhibits power conversion efficiency (PCE) as high as 20.2% when measured under AM 1.5 G illumination. This PCE makes them one of the MAPbI₃‐based inverted PVSCs that have the highest efficiency reported to date. Moreover, this inverted PVSC also shows good stability, which can retain 90% of its original efficiency after 30 days of storage in ambient air.     

The Photo‐Stability of Polymer Solar Cells: Contact Photo‐Degradation and the Benefits of Interfacial Layers

The organic/electrode interfaces in organic solar cells are systematically studied for their light, heat, and electrical stability in an inert atmosphere. Various extraction layers are examined for their effect on device stability, including poly(3,4‐ethylenedioxythiophene) poly(styrenesulfonate) (PEDOT:PSS) and MoO₃ for hole extraction layers, as well as LiF, Cs₂CO₃, and lithium acetylacetonate (Liacac) for electron extraction layers. The organic/metal interface is shown to be inherently photo‐unstable, resulting in significant losses in device efficiency with irradiation. X‐ray photoelectron spectroscopy measurements of the organic/aluminum interface suggest that the photo‐induced changes are chemical in nature. In general, interfacial layers are shown to substantially reduce photo‐degradation of the active layer/electrode interface. In spite of their photo‐stability, several interfacial layers present at the active layer/cathode interface suffer from thermal degradation effects due to temperature increases under exposure to light. Electrical aging effects are proven to be negligible in comparison to other major modes of degradation.     

Temperature‐ and Light‐Regulated Gas Transport in a Liquid Crystal Polymer Network

Azobenzene‐containing liquid crystal polymer networks (LCNs) are developed for temperature‐ and light‐regulated gas permeation. The order in a chiral‐nematic LCN (LCN*) is found to be essential to couple the unique structure of the membrane and its gas permeation responses to external stimuli such as temperature and varying irradiation conditions. An LCN membrane polymerized in the isotropic phase exhibits enhanced N₂ permeation with increasing temperature, like most traditional polymers, but barely responds to exposure with 455 and 365 nm light. In sharp contrast, a reversible decrease of N₂ transport is observed for the LCN* membrane of exactly the same chemical composition, but molecularly ordered, when submitted to an elevated temperature. More importantly, alternating in situ illumination with 455 and 365 nm light modulates reversibly N₂ permeation performance of the LCN* membrane, through the trans–cis isomerization of azo moieties. The authors postulate that, besides the anisotropic deformation of LCN*, the decreased order in LCN* membrane caused by external stimuli (i.e., increasing temperature or UV light illumination) is responsible for an inhibition of gas permeation. These results show potential applications of liquid crystal polymers in the gas transport and separation, and also contribute to the development of “smart” membranes.     

Uniformly Shaped Poly(p‐phenylenediamine) Microparticles: Shape‐controlled Synthesis and Their Potential Application for the Removal of Lead Ions from Water

A novel method for the shape‐controlled synthesis of uniformly‐shaped poly(p‐phenylenediamine) (PpPD) microparticles with different morphologies under ambient condition has been developed using HAuCl₄ as an oxidant and poly(N‐vinylpyrrolidone) (PVP) as a surfactant. The results demonstrate that the morphologies of these microparticles can be varied from symmetrical spindle‐like to diamond‐like, centrosymmetric leaf‐like, and parallelogram‐like by tuning the concentration of reactants and their molar ratios. The length of these microparticles varies from 6 to 8 µm while the width can be tuned from 2 to 4 µm. The results demonstrate that PVP as a surfactant only plays a role in controlling the morphology of the polymer particles but has no influence on the polymer structures. UV‐Vis absorption spectroscopy shows the formation of a complex between polymer ligands and lead ions by detection of new absorption peaks. Even though the as‐prepared PpPD microparticles are only partly soluble, they still show an adsorptive affinity for lead ions.     

Water‐Soluble Polyfluorenes as an Interfacial Layer Leading to Cathode‐Independent High Performance of Organic Solar Cells

Novel poly[(9,9‐bis((6′‐(N,N,N‐trimethylammonium)hexyl)‐2,7‐fluorene)‐alt‐(9,9‐bis(2‐(2‐(2‐methoxyethoxy)ethoxy)ethyl)‐9‐fluorene)) dibromide (WPF‐6‐oxy‐F) and poly[(9,9‐bis((6′‐(N,N,N‐trimethylammonium)hexyl)‐2,7‐fluorene)‐alt‐(9,9‐bis(2‐(2‐methoxyethoxy)ethyl)‐fluorene)] dibromide (WPF‐oxy‐F) compounds are developed and the use of these water‐soluble polymers as an interfacial layer for low‐cost poly(3‐hexylthiophene):phenyl‐C₆₁ butyric acid methyl ester (P3HT:PCBM) organic solar cells (OSCs) is investigated. When WPF‐oxy‐F or WPF‐6‐oxy‐F is simply inserted between the active layer and the cathode as an interfacial dipole layer by spin‐coating water‐soluble polyfluorenes, the open‐circuit voltage (V_oc), fill factor (FF), and power‐conversion efficiency (PCE) of photovoltaic cells with high work‐function metal cathodes, such as Al, Ag, Au, and Cu, dramatically increases. For example, when WPF‐6‐oxy‐F is used with Al, Ag, Au, or Cu, regardless of the work‐function of the metal cathode, the V_oc is 0.64, 0.64, 0.58, and 0.63 V, respectively, approaching the original value of the P3HT:PCBM system because of the formation of large interfacial dipoles through a reduction of the metal work‐function. In particular, introducing WPF‐6‐oxy‐F into a low‐cost Cu cathode dramatically enhanced the device efficiency from 0.8% to 3.36%.     

Original Fuel‐Cell Membranes from Crosslinked Terpolymers via a “Sol–gel” Strategy

Hybrid organic/inorganic membranes that include a functionalized (‐SO₃H), interconnected silica network, a non‐porogenic organic matrix, and a ‐SO₃H‐functionalized terpolymer are synthesized through a sol–gel‐based strategy. The use of a novel crosslinkable poly(vinylidene fluoride‐ter‐perfluoro(4‐methyl‐3,6‐dioxaoct‐7‐ene sulfonyl fluoride)‐ter‐vinyltriethoxysilane) (poly(VDF‐ter‐PFSVE‐ter‐VTEOS)) terpolymer allows a multiple tuning of the different interfaces to produce original hybrid membranes with improved properties. The synthesized terpolymer and the composite membranes are characterized, and the proton conductivity of a hybrid membrane in the absence of the terpolymer is promising, since 8 mS cm^?1 is reached at room temperature, immersed in water, with an experimental ion‐exchange‐capacity (IEC_exp) value of 0.4 meq g^?1. Furthermore, when the composite membranes contain the interfaced terpolymer, they exhibit both a higher proton conductivity (43 mS cm^?1 at 65 °C under 100% relative humidity) and better stability than the standard hybrid membrane, arising from the occurrence of a better interface between the inorganic silica and the poly[(vinylidene fluoride)‐co‐hexafluoropropylene] (poly(VDF‐co‐HFP)) copolymer network. Accordingly, the hybrid SiO₂‐SO₃H/terpolymer/poly(VDF‐co‐HFP) copolymer membrane has potential use as an electrolyte in a polymer‐electrolyte‐membrane fuel cell operating at intermediate temperatures.     

Proton Transport from Dendritic Helical‐Pore‐Incorporated Polymersomes

The ability to add synthetic channels to polymersome (polymer vesicle) membranes could lead to novel membrane composites with unique selectivity and permeability. Proton transport through two different synthetic pores, self‐assembled from either a dendritic dipeptide, (6Nf‐3,4‐3,5)12G2‐CH₂‐Boc‐L‐Tyr‐L‐Ala‐OMe, or a dendritic ester, (R)‐4Bp‐3,4‐dm8G1‐COOMe, incorporated into polymersome membranes are studied. Polymersomes provide an excellent platform for studying such transport processes due to their robustness and mechanical and chemical stability compared to liposomes. It is found that the incorporated dendritic dipeptide and dendritic ester assemble into stable helical pores in the poly(ethylene oxide)‐polybutadiene (PEO‐PBD) polymersomes but not in the poly(2‐methyloxazoline)‐poly(dimethylsiloxane)‐poly(2‐methyl oxazoline) (PMOX‐PDMS‐PMOX) polymersomes. The incorporation is confirmed by circular dichroism (CD), changes in purely synthetic mechanical strength (e.g., areal expansion modulus) as assessed by micropipette aspiration, and cryo‐TEM. In addition to the structural analyses, a transport measurement shows the incorporated dendritic helical pores allow facile transport of protons across the polymersome membranes after up to one month of storage. This integration of synthetic porous channels with polymersome substrates could provide a valuable tool for studying active transport processes in a composite membrane. These composites will ultimately expand the family of biologically inspired porous‐membrane mimics.     

Interfacial Bonding of Metal‐Sulfides with Double Carbon for Improving Reversibility of Advanced Alkali‐Ion Batteries

Engineering interfacial properties of metal‐sulfides toward excellent electrochemical capability is imperative for advanced energy‐storage materials. However, they still suffer from an unclear mechanism of capacity fading, along with ineffective physical–chemical evolution. Herein, a highly‐effective Sb₂S₃ with double carbon is designed with interfacial Sb? C bonds and double carbon, which boosts promoting of ion transferring and alleviates the separation of both active phases (Sb, S). Through “voltage‐cutting” manners, the key elements of capacity improvement about phase transitions are further determined. As expected, even at 5.0 A g^?1, the lithium‐storage capacity remains about 674 mAh g^?1. Utilized as sodium ion battery (SIB) anode, the rate capacity still reaches up to 366 mAh g^?1 at 3.0 A g^?1, much larger than that of Sb₂S₃. Obtaining the full cell of Ni–Fe Prussian blue analog versus M‐Sb₂S₃@DC, the reversible capacity is 330 mAh g^?1 at 0.5 A g^?1. Supported by kinetic analysis, the excellent rate properties are determined by the surface‐controlling behaviors, mainly resulting from the decreased capacitive resistance and improved ion moving. Furthermore, the reassembling evolution of active phases is revealed in detail by ex situ techniques. This work is expected to offer significant insights into interfacial evolutions toward advanced energy‐storage systems.     

Precious‐Metal‐Free Electrocatalysts for Activation of Hydrogen Evolution with Nonmetallic Electron Donor: Chemical Composition Controllable Phosphorous Doped Vanadium Carbide MXene

The insufficient strategies to improve electronic transport, the poor intrinsic chemical activities, and limited active site densities are all factors inhibiting MXenes from their electrocatalytic applications in terms of hydrogen production. Herein, these limitations are overcome by tunable interfacial chemical doping with a nonmetallic electron donor, i.e., phosphorization through simple heat‐treatment with triphenyl phosphine (TPP) as a phosphorous source in 2D vanadium carbide MXene. Through this process, substitution, and/or doping of phosphorous occurs at the basal plane with controllable chemical compositions (3.83–4.84 at%). Density functional theory (DFT) calculations demonstrate that the P? C bonding shows the lowest surface formation energy (ΔG_Surf) of 0.027 eV Å^?2 and Gibbs free energy (ΔG_H) of –0.02 eV, whereas others such as P‐oxide and P? V (phosphide) show highly positive ΔG_H. The P3–V₂CT_x treated at 500 °C shows the highest concentration of P? C bonds, and exhibits the lowest onset overpotential of –28 mV, Tafel slope of 74 mV dec^?1, and the smallest overpotential of ‐163 mV at 10 mA cm^?2 in 0.5 m H₂SO₄. The first strategy for electrocatalytically accelerating hydrogen evolution activity of V₂CT_x MXene by simple interfacial doping will open the possibility of manipulating the catalytic performance of various MXenes.     

Room‐Temperature Micropillar Growth of Lithium–Titanate–Carbon Composite Structures by Self‐Biased Direct Current Magnetron Sputtering for Lithium Ion Microbatteries

Here, an unidentified type of micropillar growth is described at room temperature during conventional direct‐current magnetron sputtering (DC‐MS) deposition from a Li₄Ti₅O₁₂+graphite sputter target under negative substrate bias and high operating pressure. These fabricated carbon–Li₂O–TiO₂ microstructures consisting of various Li₄Ti₅O₁₂/Li₂TiO₃/Li_x TiO₂ crystalline phases are demonstrated as an anode material in Li‐ion microbatteries. The described micropillar fabrication method is a low‐cost, substrate independent, single‐step, room‐temperature vacuum process utilizing a mature industrial complementary metal–oxide–semiconductor (CMOS)‐compatible technology. Furthermore, tentative consideration is given to the effects of selected deposition parameters and the growth process, as based on extensive physical and chemical characterization. Additional studies are, however, required to understand the exact processes and interactions that form the micropillars. If this facile method is further extended to other similar metal oxide–carbon systems, it could offer alternative low‐cost fabrication routes for microporous high‐surface area materials in electrochemistry and microelectronics.     

Parameters Influencing Charge Separation in Solid‐State Dye‐Sensitized Solar Cells Using Novel Hole Conductors

Solid‐state dye‐sensitized solar cells employing a solid organic hole‐transport material (HTM) are currently under intensive investigation, since they offer a number of practical advantages over liquid‐electrolyte junction devices. Of particular importance to the design of such devices is the control of interfacial charge transfer. In this paper, the factors that determine the yield of hole transfer at the dye/HTM interface and its correlation with solid‐state‐cell performance are identified. To this end, a series of novel triarylamine type oligomers, varying in molecular weight and mobility, are studied. Transient absorption spectroscopy is used to determine hole‐transfer yields and pore‐penetration characteristics. No correlation between hole mobility and cell performance is observed. However, it is found that the photocurrent is directly proportional to the hole‐transfer yield. This hole‐transfer yield depends on the extent of pore penetration in the dye‐sensitized film as well as on the thermodynamic driving force ΔG_dye–HTM for interfacial charge transfer. Future design of alternative solid‐state HTMs should focus on the optimization of pore‐filling properties and the control of interfacial energetics rather than on increasing material hole mobilities.     

Solution‐Processed,Alkali Metal‐Salt‐Doped,Electron‐Transport Layers for High‐Performance Phosphorescent Organic Light‐Emitting Diodes

High‐performance, blue, phosphorescent organic light‐emitting diodes (PhOLEDs) are achieved by orthogonal solution‐processing of small‐molecule electron‐transport material doped with an alkali metal salt, including cesium carbonate (Cs₂CO₃) or lithium carbonate (Li₂CO₃). Blue PhOLEDs with solution‐processed 4,7‐diphenyl‐1,10‐phenanthroline (BPhen) electron‐transport layer (ETL) doped with Cs₂CO₃ show a luminous efficiency (LE) of 35.1 cd A^?1 with an external quantum efficiency (EQE) of 17.9%, which are two‐fold higher efficiency than a BPhen ETL without a dopant. These solution‐processed blue PhOLEDs are much superior compared to devices with vacuum‐deposited BPhen ETL/alkali metal salt cathode interfacial layer. Blue PhOLEDs with solution‐processed 1,3,5‐tris(m‐pyrid‐3‐yl‐phenyl)benzene (TmPyPB) ETL doped with Cs₂CO₃ have a luminous efficiency of 37.7 cd A^?1 with an EQE of 19.0%, which is the best performance observed to date in all‐solution‐processed blue PhOLEDs. The results show that a small‐molecule ETL doped with alkali metal salt can be realized by solution‐processing to enhance overall device performance. The solution‐processed metal salt‐doped ETLs exhibit a unique rough surface morphology that facilitates enhanced charge‐injection and transport in the devices. These results demonstrate that orthogonal solution‐processing of metal salt‐doped electron‐transport materials is a promising strategy for applications in various solution‐processed multilayered organic electronic devices.