Nanostructured Silicon Anodes for High‐Performance Lithium‐Ion Batteries

Despite the high theoretical capacity of Si anodes, the electrochemical performance of Si anodes is hampered by severe volume changes during lithiation and delithiation, leading to poor cyclability and eventual electrode failure. Nanostructured silicon and its nanocomposite electrodes could overcome this problem holding back the deployment of Si anodes in lithium‐ion batteries (LIBs) by providing facile strain relaxation, short lithium diffusion distances, enhanced mass transport, and effective electrical contact. Here, the recent progress in nanostructured Si‐based anode materials such as nanoparticles, nanotubes, nanowires, porous Si, and their respective composite materials and fabrication processes in the application of LIBs have been reviewed. The ability of nanostructured Si materials in addressing the above mentioned challenges have been highlighted. Future research directions in the field of nanostructured Si anode materials for LIBs are summarized.     

A LiF Nanoparticle‐Modified Graphene Electrode for High‐Power and High‐Energy Lithium Ion Batteries

Surface modification of carbon materials plays an important role in tailoring carbon surface chemistry to specify their electrochemical performance. Here, a surface modification strategy for graphene is proposed to produce LiF‐nanoparticle‐modified graphene as a high‐rate, large‐capacity pre‐lithiated electrode for high‐power and high‐energy lithium ion batteries. The LiF nanoparticles covering the active sites of the graphene surface provide an extra Li source and act as an effective solid electrolyte interphase (SEI) inhibiter to suppress LiFP₆ electrolyte decomposition reactions, affect SEI components, and reduce their thickness. Consequently, the Li‐ion diffusion is greatly sped up and the thermodynamic stability of the electrode is significantly improved. This modified graphene electrode shows excellent rate capability and improved first‐cycle coulombic efficiency, cycling stability, and ultrahigh power and energy densities accessible during fast charge/discharge processes.     

Multifunctional Electrode Design Consisting of 3D Porous Separator Modulated with Patterned Anode for High‐Performance Dual‐Ion Batteries

Searching for low‐cost and high‐capacity electrode materials such as metal anodes is of important significance for the development of new generation rechargeable batteries. However, metal anodes always suffer from severe volume expansion/contraction during a repeated electrochemical alloying/dealloying process. In this study, a novel concept about modifying metal‐anodes‐based battery construction with a multifunctional electrode (ME) design is provided. The ME consists of a 3D porous separator that is modulated with a patterned aluminum anode, which simultaneously works as a current collector, anode material, and separator in a dual‐ion battery (DIB). The 3D porous separator not only enables the ME to possess significantly improved electrolyte uptake and retention capabilities, but also acts as a protecting layer to restrict the surface pulverization of the Al anode. The ME‐DIB displays remarkably enhanced cell performances, including excellent cycling stability with 92.4% capacity retention after 1000 cycles at a current density of 2 C, and superior rate performance with 80.7% capacity retention at 10 C.     

Rational Molecular Design of Benzoquinone‐Derived Cathode Materials for High‐Performance Lithium‐Ion Batteries

p‐Benzoquinone (BQ) is a promising cathode material for lithium‐ion batteries (LIBs) due to its high theoretical specific capacity and voltage. However, it suffers from a serious dissolution problem in organic electrolytes, leading to poor electrochemical performance. Herein, two BQ‐derived molecules with a near‐plane structure and relative large skeleton: 1,4‐bis(p‐benzoquinonyl)benzene (BBQB) and 1,3,5‐tris(p‐benzoquinonyl)benzene (TBQB) are designed and synthesized. They show greatly decreased solubility as a result of strong intermolecular interactions. As cathode materials for LIBs, they exhibit high carbonyl utilizations of 100% with high initial capacities of 367 and 397 mAh g^?1, respectively. Especially, BBQB with better planarity presents remarkably improved cyclability, retaining a high capacity of 306 mAh g^?1 after 100 cycles. The cycling stability of BBQB surpasses all reported BQ‐derived small molecules and most polymers. This work provides a new molecular structure design strategy to suppress the dissolution of organic electrode materials for achieving high performance rechargeable batteries.     

Optical Enhancement via Electrode Designs for High‐Performance Polymer Solar Cells

To capture the essence of the rapid progress in optical engineering exploited in high‐performance polymer solar cells (PSCs), a comprehensive overview focusing on recent developments and achievements in PSC electrode engineering is provided in this review. To date, various kinds of electrode materials and geometries are exploited to enhance light‐trapping in devices through distinct optical strategies. In addition to the widely used nanostructured electrodes that induce plasmonic‐enhanced light absorption, planar ultra‐thin metal films also have attracted significant attention due to their remarkably reflective transparent properties that beget efficient optical microcavities. These microcavities confine incident light with resonant frequencies between two reflective electrodes due to optically coherent interference, boosting the light absorption of thin‐film PSCs while maintaining efficient charge dissociation and extraction. After reviewing the challenges in developing high‐performance microcavity‐enhanced PSCs (MCPSCs), we discuss strategies to improve MCPSC performance further to showcase the potential of harnessing microcavity resonance effects in thin‐film PSCs.     

Recent Advances in Mn-Rich Layered Materials for Sodium-Ion Batteries

Branded with low cost and a high degree of safety, with an ambitious aim of substituting lithium-ion batteries in many fields, sodium-ion batteries have received fervid attention in recent years after being dormant for decades. Layered materials are a major focus of study owing to the extensive experience already gained in lithium-ion batteries, and the pursuit of a Mn-rich composition is critical to reduce the cost while retaining the performance. This review provides a timely update of the recent progress of Mn-rich layered materials for sodium-ion batteries based on the understandings of the phase forming principles, structure transformation upon cycling and charge compensation mechanisms and discusses potential ambiguities in the pursuit of high-performance materials.     

Amorphous GaN@Cu Freestanding Electrode for High‐Performance Li‐Ion Batteries

GaN is demonstrated to be an ideal anode for Li‐ion batteries (LIBs) for the first time. Amorphous GaN@Cu nanorods (a‐GaN@Cu) freestanding electrode is designed via a low‐temperature pulsed laser deposition method, which exhibits prominent rate capability and untralong lifespan as an anode for LIBs. With porous interconnected metal nanorods substrate to improve the structure integrity and electronic conductivity, the a‐GaN@Cu electrode delivers a capacity recovery of 980 mAh g^?1 after 150 cycles from 0.25 to 6.25 A g^?1 and a high discharge capacity of 509 mAh g^?1 after 3000 cycles at 10.0 A g^?1. The lithium storage in the a‐GaN is also systematically studied, which suggests a redox reaction mechanism.     

Highly Stretchable Conductive Glue for High‐Performance Silicon Anodes in Advanced Lithium‐Ion Batteries

Binder plays a key role in maintaining the mechanical integrity of electrodes in lithium‐ion batteries. However, the existing binders typically exhibit poor stretchability or low conductivity at large strains, which are not suitable for high‐capacity silicon (Si)‐based anodes undergoing severe volume changes during cycling. Herein, a novel stretchable conductive glue (CG) polymer that possesses inherent high conductivity, excellent stretchablity, and ductility is designed for high‐performance Si anodes. The CG can be stretched up to 400% in volume without conductivity loss and mechanical fracture and thus can accommodate the large volume change of Si nanoparticles to maintain the electrode integrity and stabilize solid electrolyte interface growth during cycling while retaining the high conductivity, even with a high Si mass loading of 90%. The Si‐CG anode has a large reversible capacity of 1500 mA h g^?1 for over 700 cycles at 840 mA g^?1 with a large initial Coulombic efficiency of 80% and high rate capability of 737 mA h g^?1 at 8400 mA g^?1. Moreover, the Si‐CG anode demonstrates the highest achieved areal capacity of 5.13 mA h cm^?2 at a high mass loading of 2 mg cm^?2. The highly stretchable CG provides a new perspective for designing next‐generation high‐capacity and high‐power batteries.     

Application of 2D MXene in Organic Electrode Materials for Rechargeable Batteries: Recent Progress and Perspectives

Organic electrode materials (OEMs) are emerging green power because of the promising advantages such as environmental friendliness, abundant sources, easy recycling, and structural diversity. However, several inherent issues, including low electronic conductivity, dissolution of active materials, and particle pulverization restrict their practical application. MXene, as a novel 2D material has exhibited enormous potential to solve the issues of OEMs due to its high conductivity, unique structure, exceptional mechanical property, and abundant surface groups. Up to now, various effective strategies have been presented and achieved positive effects, such as constructing heterojunction structures, in situ assembly, dip-coating, preparing free-standing MXene paper, etc. Nonetheless, comprehensive review of the progress and status is rare. Herein, an overview of the application of MXene in organic electrode materials for rechargeable batteries is systematically put forward. Meanwhile, recent progress and future development directions are presented. This review can serve as a guide for future research.     

One‐Pot Synthesis of Antimony‐Embedded Silicon Oxycarbide Materials for High‐Performance Sodium‐Ion Batteries

Sodium‐ion batteries have recently attracted intensive attention due to their natural abundance and low cost. Antimony is a desirable candidate for an anode material for sodium‐ion batteries due to its high theoretical capacity (660 mA h g^?1). However, the utilization of alloy‐based anodes is still limited by their inherent huge volume changes and sluggish kinetics. The Sb‐embedded silicon oxycarbide (SiOC) composites are simply synthesized via a one‐pot pyrolysis process at 900 °C without any additives or surfactants, taking advantage of the superior self‐dispersion properties of antimony acetate powders in silicone oil. The structural and morphological characterizations confirm that Sb nanoparticles are homogeneously embedded into the amorphous SiOC matrix. The composite materials exhibit an initial desodiation capacity of around 510 mA h g^?1 and maintained an excellent capacity retention above 97% after 250 cycles. The rate capability test reveals that the composites deliver capacity greater than 453 mA h g^?1, even at the high current density of 20 C rate, owing to the free‐carbon domain of SiOC material. The electrochemical and postmortem analyses confirm that the SiOC matrix with a uniform distribution of Sb nanoparticles provides the mechanical strength without degradation in conductive characteristics, suppressing the agglomeration of Sb particles during the electrochemical reaction.     

All‐Purpose Electrode Design of Flexible Conductive Scaffold toward High‐Performance Li–S Batteries

The main obstacles that hinder the development of efficient lithium sulfur (Li–S) batteries are the polysulfide shuttling effect in sulfur cathode and the uncontrollable growth of dendritic Li in the anode. An all‐purpose flexible electrode that can be used both in sulfur cathode and Li metal anode is reported, and its application in wearable and portable storage electronic devices is demonstrated. The flexible electrode consists of a bimetallic CoNi nanoparticle‐embedded porous conductive scaffold with multiple Co/Ni‐N active sites (CoNi@PNCFs). Both experimental and theoretical analysis show that, when used as the cathode, the CoNi and Co/Ni‐N active sites implanted on the porous CoNi@PNCFs significantly promote chemical immobilization toward soluble lithium polysulfides and their rapid conversion into insoluble Li₂S, and therefore effectively mitigates the polysulfide shuttling effect. Additionally, a 3D matrix constructed with porous carbonous skeleton and multiple active centers successfully induces homogenous Li growth, realizing a dendrite‐free Li metal anode. A Li–S battery assembled with S/CoNi@PNCFs cathode and Li/CoNi@PNCFs anode exhibits a high reversible specific capacity of 785 mAh g^?1 and long cycle performance at 5 C (capacity fading rate of 0.016% over 1500 cycles).     

Interpenetrated Gel Polymer Binder for High‐Performance Silicon Anodes in Lithium‐ion Batteries

Silicon has attracted ever‐increasing attention as a high‐capacity anode material in Li‐ion batteries owing to its extremely high theoretical capacity. However, practical application of silicon anodes is seriously hindered by its fast capacity fading as a result of huge volume changes during the charge/discharge process. Here, an interpenetrated gel polymer binder for high‐performance silicon anodes is created through in‐situ crosslinking of water‐soluble poly(acrylic acid) (PAA) and polyvinyl alcohol (PVA) precursors. This gel polymer binder with deformable polymer network and strong adhesion on silicon particles can effectively accommodate the large volume change of silicon anodes upon lithiation/delithiation, leading to an excellent cycling stability and high Coulombic efficiency even at high current densities. Moreover, high areal capacity of ～4.3 mAh/cm² is achieved based on the silicon anode using the gel PAA–PVA polymer binder with a high mass loading. In view of simplicity in using the water soluble gel polymer binder, it is believed that this novel binder has a great potential to be used for high capacity silicon anodes in next generation Li‐ion batteries, as well as for other electrode materials with large volume change during cycling.     

Iron Oxide Nanoparticle and Graphene Nanoribbon Composite as an Anode Material for High‐Performance Li‐Ion Batteries

A composite material made of graphene nanoribbons and iron oxide nanoparticles provides a remarkable route to lithium‐ion battery anode with high specific capacity and cycle stability. At a rate of 100 mA/g, the material exhibits a high discharge capacity of ~910 mAh/g after 134 cycles, which is >90% of the theoretical li‐ion storage capacity of iron oxide. Carbon black, carbon nanotubes, and graphene flakes have been employed by researchers to achieve conductivity and stability in lithium‐ion electrode materials. Herein, the use of graphene nanoribbons as a conductive platform on which iron oxide nanoparticles are formed combines the advantages of long carbon nanotubes and flat graphene surfaces. The high capacity over prolonged cycling achieved is due to the synergy between an electrically percolating networks of conductive graphene nanoribbons and the high lithium‐ion storage capability of iron oxide nanoparticles.     

Advanced Concentration Gradient Cathode Material with Two‐Slope for High‐Energy and Safe Lithium Batteries

Li[Ni_0.65Co_0.13Mn_0.22]O₂ cathode with two‐sloped full concentration gradient (TSFCG), maximizing the Ni content in the inner part of the particle and the Mn content near the particle surface, is synthesized via a specially designed batch‐type reactor. The cathode delivers a discharge capacity of 200 mAh g^?1 (4.3 V cutoff) with excellent capacity retention of 88% after 1500 cycles in a full‐cell configuration. Overall electrochemical performance of the TSFCG cathode is benchmarked against conventional cathode (CC) with same composition and commercially available Li[Ni_0.8Co_0.15Al_0.05]O₂ (NCA). The TSFCG cathode exhibits the best cycling stability, rate capability, and thermal stability of the three electrodes. Transmission electron microscopy analysis of the cycled TSFCG, CC, and NCA cathodes shows that the TSFCG electrode maintains both its mechanical and structural integrity whereas the NCA electrode nearly pulverizes due to the strain during cycling.     

Stress Relief Principle of Micron‐Sized Anodes with Large Volume Variation for Practical High‐Energy Lithium‐Ion Batteries

Practical applications of high gravimetric and volumetric capacity anodes for next‐generation lithium‐ion batteries have attracted unprecedented attentions, but still faced challenges by their severe volume changes, rendering low Coulombic efficiency and fast capacity fading. Nano and void‐engineering strategies had been extensively applied to overcome the large volume fluctuations causing the continuous irreversible reactions upon cycling, but they showed intrinsic limit in fabrication of practical electrode condition. Achieving high electrode density is particularly paramount factor in terms of the commercial feasibility, which is mainly dominated by the true density and tapping density of active material. Herein, based on finite element method calculation, micron‐sized double passivation layered Si/C design is introduced with restrictive lithiation state, which can withstand the induced stress from Li insertion upon repeated cycling. Such design takes advantage in structural integrity during long‐term cycling even at high gravimetric capacity (1400 mAh g^?1). In 1 Ah pouch‐type full‐cell evaluation with high mass loading and electrode density (≈3.75 mAh cm^?2 and ≈1.65 g cm^?3), it demonstrates superior cycle stability without rapid capacity drop during 800 cycles.     

CoS Quantum Dot Nanoclusters for High‐Energy Potassium‐Ion Batteries

Potassium‐ion batteries (PIBs) are a promising alternative to lithium‐ion batteries because potassium is an abundant natural resource. To date, PIBs are in the early stages of exploration and only a few anode materials have been investigated. This study reports a cobalt sulfide and graphene (CoS@G) composite as anode electrode for PIBs for the first time. The composite features interconnect quantum dots of CoS nanoclusters uniformly anchored on graphene nanosheets. The coexistence of CoS quantum dot nanoclusters and graphene nanosheets endows the composite with large surface area, highly conductive network, robust structural stability, and excellent electrochemical energy storage performance. An unprecedented capacity of 310.8 mA h g^?1 at 500 mA g^?1 is obtained after 100 cycles, with a rate capability better than an equivalent sodium‐ion batteries (SIBs). This work provides the evidence that PIBs can be a promising alternative to SIBs, especially at high charge–discharge rates. The development of the CoS@G anode material also provides the basis of expanding the library of suitable anode materials for PIBs.     

Approaching the Downsizing Limit of Maricite NaFePO4 toward High‐Performance Cathode for Sodium‐Ion Batteries

Maricite NaFePO₄ nanodots with minimized sizes (≈1.6 nm) uniformly embedded in porous N‐doped carbon nanofibers (designated as NaFePO₄@C) are first prepared by electrospinning for maximized Na‐storage performance. The obtained flexible NaFePO₄@C fiber membrane adherent on aluminum foil is directly used as binder‐free cathode for sodium‐ion batteries, revealing that the ultrasmall nanosize effect as well as a high‐potential desodiation process can transform the generally perceived electrochemically inactive maricite NaFePO₄ into a highly active amorphous phase; meanwhile, remarkable electrochemical performance in terms of high reversible capacity (145 mA h g^?1 at 0.2 C), high rate capability (61 mA h g^?1 at 50 C), and unprecedentedly high cyclic stability (≈89% capacity retention over 6300 cycles) is achieved. Furthermore, the soft package Na‐ion full battery constructed by the NaFePO₄@C nanofibers cathode and the pure carbon nanofibers anode displays a promising energy density of 168.1 Wh kg^?1 and a notable capacity retention of 87% after 200 cycles. The distinctive 3D network structure of very fine NaFePO₄ nanoparticles homogeneously encapsulated in interconnected porous N‐doped carbon nanofibers, can effectively improve the active materials' utilization rate, facilitate the electrons/Na⁺ ions transport, and strengthen the electrode stability upon prolonged cycling, leading to the fascinating Na‐storage performance.     

Reversible and High‐Capacity Nanostructured Electrode Materials for Li‐Ion Batteries

Reversible nanostructured electrode materials are at the center of research relating to rechargeable lithium batteries, which require high power, high capacity, and high safety. The higher capacities and higher rate capabilities for the nanostructured electrode materials than for the bulk counterparts can be attributed to the higher surface area, which reduces the overpotential and allows faster reaction kinetics at the electrode surface. These electrochemical enhancements can lead to versatile potential applications of the batteries and can provide breakthroughs for the currently limited power suppliers of mobile electronics. This Feature Article describes recent research advances on nanostructured cathode and anode materials, such as metals, metal oxides, metal phosphides and LiCoO₂, LiNi_1–xM_xO₂ with zero‐, one‐, two‐, and three‐dimensional morphologies.     

Natural Vermiculite Enables High‐Performance in Lithium–Sulfur Batteries via Electrical Double Layer Effects

Lithium–sulfur batteries with potentially high specific energy are viewed as very promising candidates for next‐generation lightweight and low‐cost rechargeable batteries. However, sulfur‐based cathodes suffer from dissolution of polysulfides causing shuttle effects. Here, in order to confine elemental sulfur and anchor the polysulfides, a novel host that is an inexpensive natural clay mineral, viz., vermiculite is proposed. When compared to regular carbon–sulfur composites, vermiculite–sulfur composites offer promising rate capability and much better cycling stabilities, displaying capacity retentions of ≈89 and ≈93% within 200 cycles at C/2 and 1 C, respectively, and ≈60 % at C/5 within 1000 cycles. Postmortem studies, advanced adsorption tests, density functional theory calculations, and zeta potential measurements in combination with intrinsic characteristics of the natural vermiculite provide insights into the new mechanism. The vermiculite contains naturally present surface cations which show a strong tendency to adsorb S_n^2? anions, hence protecting them from dissolution. The excess surface charge is most probably compensated by excess Li⁺ in the space charge zones which is beneficial for charge transfer and local conductivity. The reported results show that natural clay‐minerals are promising sulfur hosts being able to fixate sulfides via electrical double layer effects, thus enabling high‐performance in lithium–chalcogen batteries.     

A High‐Energy Li‐Ion Battery Using a Silicon‐Based Anode and a Nano‐Structured Layered Composite Cathode

High capacity electrodes based on a Si composite anode and a layered composite oxide cathode, Ni‐rich Li[Ni_0.75Co_0.1Mn_0.15]O₂, are evaluated and combined to fabricate a high energy lithium ion battery. The Si composite anode, Si/C‐IWGS (internally wired with graphene sheets), is prepared by a scalable sol–gel process. The Si/C‐IWGS anode delivers a high capacity of >800 mAh g^?1 with an excellent cycling stability of up to 200 cycles, mainly due to the small amount of graphene (～6 wt%). The cathode (Li[Ni_0.75Co_0.1Mn_0.15]O₂) is structurally optimized (Ni‐rich core and a Ni‐depleted shell with a continuous concentration gradient between the core and shell, i.e., a full concentration gradient, FCG, cathode) so as to deliver a high capacity (>200 mAh g^?1) with excellent stability at high voltage (～4.3 V). A novel lithium ion battery system based on the Si/C‐IWGS anode and FCG cathode successfully demonstrates a high energy density (240 Wh kg^?1 at least) as well as an unprecedented excellent cycling stability of up to 750 cycles between 2.7 and 4.2 V at 1C. As a result, the novel battery system is an attractive candidate for energy storage applications demanding a high energy density and long cycle life.