Self‐Healing and Stretchable 3D‐Printed Organic Thermoelectrics

With the advent of flexible and wearable electronics and sensors, there is an urgent need to develop energy‐harvesting solutions that are compatible with such wearables. However, many of the proposed energy‐harvesting solutions lack the necessary mechanical properties, which make them susceptible to damage by repetitive and continuous mechanical stresses, leading to serious degradation in device performance. Developing new energy materials that possess high deformability and self‐healability is essential to realize self‐powered devices. Herein, a thermoelectric ternary composite is demonstrated that possesses both self‐healing and stretchable properties produced via 3D‐printing method. The ternary composite films provide stable thermoelectric performance during viscoelastic deformation, up to 35% tensile strain. Importantly, after being completely severed by cutting, the composite films autonomously recover their thermoelectric properties with a rapid response time of around one second. Using this self‐healable and solution‐processable composite, 3D‐printed thermoelectric generators are fabricated, which retain above 85% of their initial power output, even after repetitive cutting and self‐healing. This approach represents a significant step in achieving damage‐free and truly wearable 3D‐printed organic thermoelectrics.     

Plasticization of PEDOT:PSS by Common Additives for Mechanically Robust Organic Solar Cells and Wearable Sensors

Despite the ubiquity of poly(3,4‐ethylenedioxythiophene):poly(styrenesulfonate) (PEDOT:PSS) in applications demanding mechanical flexibility, the effect on the mechanical properties of common additives—i.e., dimethylsulfoxide (DMSO), Zonyl fluorosurfactant (Zonyl), and poly(ethyleneimine) (PEI)—has not been reported. This paper describes these effects and uses plasticized films in solar cells and mechanical sensors for the detection of human motion. The tensile moduli of films spin‐coated from solutions containing 0%, 5%, and 10% DMSO and 0.1%, 1%, and 10% Zonyl (nine samples total) are measured using the buckling technique, and the ductility is inferred from measurements of the strain at which cracks form on elastic substrates. Elasticity and ductility are maximized in films deposited from solutions containing 5% DMSO and 10% Zonyl, but the conductivity is greatest for samples containing 0.1% Zonyl. These experiments reveal enlargement of presumably PEDOT‐rich grains, visible by atomic force microscopy, when the amount of DMSO is increased from 0% to 5%. PEI—which is used to lower the work function of PEDOT:PSS—has a detrimental effect on the mechanical properties of the PEDOT:PSS/PEI bilayer films. Wearable electronic sensors employing PEDOT:PSS films containing 5% DMSO and 10% Zonyl are ­fabricated, which exhibit detectable responses at 20% strain and high mechanical robustness through elastic deformation.     

Hydrogel‐Enabled Transfer‐Printing of Conducting Polymer Films for Soft Organic Bioelectronics

The use of conducting polymers such as poly(3,4‐ethylenedioxythiophene) polystyrene sulfonate (PEDOT:PSS) for the development of soft organic bioelectronic devices, such as organic electrochemical transistors (OECTs), is rapidly increasing. However, directly manipulating conducting polymer thin films on soft substrates remains challenging, which hinders the development of conformable organic bioelectronic devices. A facile transfer‐printing of conducting polymer thin films from conventional rigid substrates to flexible substrates offers an alternative solution. In this work, it is reported that PEDOT:PSS thin films on glass substrates, once mixed with surfactants, can be delaminated with hydrogels and thereafter be transferred to soft substrates without any further treatments. The proposed method allows easy, fast, and reliable transferring of patterned PEDOT:PSS thin films from glass substrates onto various soft substrates, facilitating their application in soft organic bioelectronics. By taking advantage of this method, skin‐attachable tattoo‐OECTs are demonstrated, relevant for conformable, imperceptible, and wearable organic biosensing.     

Over 16.7% Efficiency Organic‐Silicon Heterojunction Solar Cells with Solution‐Processed Dopant‐Free Contacts for Both Polarities

Realization of synchronous improvement in optical management and electrical engineering is necessary to achieve high‐performance photovoltaic device. However, inherent challenges are faced in organic‐silicon heterojunction solar cells (HSCs) due to the poor contact property of polymer on structured silicon surface. Herein, a remarkable efficiency boost from 12.6% to over 16.7% in poly(3,4‐ethylenedioxythiophene):poly(styrenesulfonate)/n‐silicon (PEDOT:PSS/n‐Si) HSCs by independent optimization of hole‐/electron‐selective contacts only relying on solution‐based processes is realized. A bilayer PEDOT:PSS film with different functionalizations is utilized to synchronously realize conformal contact and effective carrier collection on textured Si surface, making the photogenerated carriers be well separated at heterojunction interface. Meanwhile, fullerene derivative is used as electron‐transporting layer at the rear n‐Si/Al interface to reduce the contact barrier. The study of carriers' transport and independent optimization on separately contacted layers may lead to an effective and simplified path to fabricate high‐performance organic‐silicon heterojunction devices.     

Stretchable and Transparent Conductive PEDOT:PSS‐Based Electrodes for Organic Photovoltaics and Strain Sensors Applications

The development of transparent, conducting, and stretchable poly(3,4‐ethylenedioxythiophene):poly(styrenesulfonate) (PEDOT:PSS)‐based electrodes using a combination of a polyethylene oxide (PEO) polymer network and the surfactant Zonyl is reported. The latter improves the ductility of PEDOT:PSS and enables its deposition on hydrophobic surfaces such as polydimethylsiloxane (PDMS) elastomers, while the presence of a 3D matrix offers high electrical conductivity, elasticity, and mechanical recoverability. The resulting electrode exhibits attractive properties such as high electrical conductivity of up to 1230 S cm^?1 while maintaining high transparency of 95% at 550 nm. The potential of the electrode technology is demonstrated in indium‐tin‐oxide (ITO)‐free solar cells using the PBDB‐T‐2F:IT‐4F blend with a power conversion efficiency of 12.5%. The impact of repeated stretch‐and‐release cycles on the electrical resistance is also examined in the effort to evaluate the properties of the electrodes. The interpenetrated morphology of the PEDOT:PSS and polyethylene oxide network is found to exhibit beneficial synergetic effects resulting in excellent mechanical stretchability and high electrical conductivity. By carefully tuning the amount of additives, the ability to detect small changes in electrical resistance as a function of mechanical deformation is demonstrated, which enables the demonstration of stretchable and resilient on‐skin strain sensors capable of detecting small motions of the finger.     

Flexible Transparent Bifunctional Capacitive Sensors with Superior Areal Capacitance and Sensing Capability based on PEDOT:PSS/MXene/Ag Grid Hybrid Electrodes

Flexible transparent supercapacitors (FTSs) have aroused considerable attention. Nonetheless, balancing energy storage capability and transparency remains challenging. Herein, a new type of FTSs with both excellent energy storage and superior transparency is developed based on PEDOT:PSS/MXene/Ag grid ternary hybrid electrodes. The hybrid electrodes can synergistically utilize the high optoelectronic properties of Ag grids, the excellent capacitive performance of MXenes, and the superior chemical stability of PEDOT:PSS, thus, simultaneously demonstrating excellent optoelectronic properties (T: ≈89%, R_s: ≈39 Ω sq⁻¹), high areal specific capacitance, superior mechanical softness, and excellent anti-oxidation capability. Due to the excellent comprehensive performances of the hybrid electrodes, the resulting FTSs exhibit both high optical transparency (≈71% and ≈60%) and large areal specific capacitance (≈3.7 and ≈12 mF cm⁻²) besides superior energy storage capacity (P: 200.93, E: 0.24 µWh cm⁻²). Notably, the FTSs show not only excellent energy storage but also exceptional sensing capability, viable for human activity recognition. This is the first time to achieve FTSs that combine high transparency, excellent energy storage and good sensing all-in-one, which make them stand out from conventional flexible supercapacitors and promising for next-generation smart flexible energy storage devices.     

Bio‐Inspired All‐Organic Soft Actuator Based on a π–π Stacked 3D Ionic Network Membrane and Ultra‐Fast Solution Processing

Next generation electronic products, such as wearable electronics, flexible displays, and smart mobile phones, will require the use of unprecedented electroactive soft actuators for haptic and stimuli‐responsive devices and space‐saving bio‐mimetic actuation. Here, a bio‐inspired all‐organic soft actuator with a π–π stacked and 3D ionic networked membrane based on naphthalene‐tetracarboxylic dianhydride (Ntda) and sulfonated polyimide block copolymers (SPI) is presented, utilizing an ultra‐fast solution process. The π–π stacked and self‐assembled 3D ionic networked membrane with continuous and interconnected ion transport nanochannels is synthesized by introducing simple and strong atomic level regio‐specific interactions of hydrophilic and hydrophobic SPI co‐blocks with cations and anions in the ionic liquid. Furthermore, a facile and ultrafast all‐solution process involving solvent blending, dry casting, and solvent dropping is developed to produce electro‐active soft actuators with highly conductive polyethylenedioxythiophene (PEDOT):polystyrenesulfonate (PSS) electrodes. Ionic conductivity and ion exchange capacity of the π–π stacked Ntda‐SPI membrane can be increased up to 3.1 times and 3.4 times of conventional SPI, respectively, resulting in a 3.2 times larger bending actuation. The developed bio‐inspired soft actuator is a good candidate for satisfying the tight requirements of next generation soft electronic devices due to its key benefits such as low operating voltage and comparatively large strains, as well as quick response and facile processability.     

Stretching‐Induced Growth of PEDOT‐Rich Cores: A New Mechanism for Strain‐Dependent Resistivity Change in PEDOT:PSS Films

It remains a fundamental challenge in the development of stretchable electronics to understand how mechanical strain changes the electrical properties of materials. Although the piezoresistive behavior of poly(3,4‐ethylene‐ dioxythiophene):poly(styrenesulfonate) (PEDOT:PSS) has been observed, its intrinsic origin is not yet fully understood because there are many extrinsic contributing factors and an experimental platform with which to assess such behavior has not been established. Here, systematic analysis shows that the matching Poisson's ratio and elastic modulus between PEDOT:PSS films and their underlying substrates is important in decoupling the factors that affect the material's piezoresistivity, allowing for tunable resistivity. Based on such a fundamental understanding, the conductivity of PEDOT:PSS can be controlled to be invariant and decrease as a function of applied tensile stress. Furthermore, a linear response of the resistivity with respect to mechanical strains of up to 60%, which has never before been realized, is shown. The irreversible conductivity enhancement is primarily caused by the coalescence‐induced growth of conductive PEDOT‐rich cores.     

A Wrinkled PEDOT:PSS Film Based Stretchable and Transparent Triboelectric Nanogenerator for Wearable Energy Harvesters and Active Motion Sensors

The functionalized conductive polymer is a promising choice for flexible triboelectric nanogenerators (TENGs) for harvesting human motion energy still poses challenges. In this work, a transparent and stretchable wrinkled poly(3,4‐ethylenedioxythiophene):poly(4‐styrenesulfonate) (PEDOT:PSS) electrode based TENG (WP‐TENG) is fabricated. The optimum conductivity and transparency of PEDOT:PSS electrode can reach 0.14 kΩ □⁻¹ and 90%, respectively, with maximum strain of ≈100%. Operating in single‐electrode mode at 2.5 Hz, the WP‐TENG with an area of 6 × 3 cm² produces an open‐circuit voltage of 180 V, short‐circuit current of 22.6 µA, and average power density of 4.06 mW m⁻². It can be worn on the wrist to harvest hand tapping energy and charge the capacitor to 2 V in ≈3.5 min, and then drive an electronic watch. Furthermore, the WP‐TENG as the human motion monitoring sensor could inspect the bending angle of the elbow and joint by analyzing the peak value of voltage and monitor the motion frequency by counting the peak number. The triboelectric mechanism also enables the WP‐TENG to realize high‐performance active tactile sensing. The assembled 3 pixel × 3 pixel tactile sensor array is fabricated for mapping the touch location or recording the shape of object contacted with the sensor array.     

Paper with Power: Engraving 2D Materials on 3D Structures for Printed,High‐Performance,Binder‐Free,and All‐Solid‐State Supercapacitors

The prevalence of the Internet of Things (IoT) and wearable electronics create an unprecedented demand for new power sources which are low cost, high performance, and flexible in many application settings. In this paper, a strategy for the scalable fabrication of high‐performance, all‐solid‐state supercapacitors (SCs) is demonstrated using conventional paper and an inkjet printer. Emerging printed electronics technology and low‐cost chemical engraving methods are bridged for the first time to construct Cu_xO nanosheets, in situ, on the 3D metallized fiber structures. Benefitting from both the “2D Materials on 3D Structures” design and the binder‐free nature of the fabricated electrodes, substantial improvements to electrical conductivity, aerial capacitance, and electrochemical performance of the resulting SCs are observed. With the proposed strategy, the fabricated SCs can be seamlessly integrated into any printed circuit, sensors, or artwork; the properties of these SCs can be easily tuned by simple pattern design, fulfilling the increasing demand of highly customized power systems in the IoT and flexible/wearable electronics industries.     

Flexible Hybrid Electronics: Direct Interfacing of Soft and Hard Electronics for Wearable Health Monitoring

The interfacing of soft and hard electronics is a key challenge for flexible hybrid electronics. Currently, a multisubstrate approach is employed, where soft and hard devices are fabricated or assembled on separate substrates, and bonded or interfaced using connectors; this hinders the flexibility of the device and is prone to interconnect issues. Here, a single substrate interfacing approach is reported, where soft devices, i.e., sensors, are directly printed on Kapton polyimide substrates that are widely used for fabricating flexible printed circuit boards (FPCBs). Utilizing a process flow compatible with the FPCB assembly process, a wearable sensor patch is fabricated composed of inkjet‐printed gold electrocardiography (ECG) electrodes and a stencil‐printed nickel oxide thermistor. The ECG electrodes provide 1 mVp–p ECG signal at 4.7 cm electrode spacing and the thermistor is highly sensitive at normal body temperatures, and demonstrates temperature coefficient, α ≈ –5.84% K^–1 and material constant, β ≈ 4330 K. This sensor platform can be extended to a more sophisticated multisensor platform where sensors fabricated using solution processable functional inks can be interfaced to hard electronics for health and performance monitoring, as well as internet of things applications.     

Scaling Effects on the Electrochemical Performance of poly(3,4‐ethylenedioxythiophene (PEDOT), Au,and Pt for Electrocorticography Recording

Reduced contact size would permit higher resolution cortical recordings, but the effects of diameter on crucial recording and stimulation properties are poorly understood. Here, the first systematic study of scaling effects on the electrochemical properties of metallic Pt and Au and organic poly(3,4‐ethylenedioxythiophene):polystyrene sulfonate (PEDOT:PSS) electrodes is presented. PEDOT:PSS exhibits better faradaic charge transfer and capacitive charge coupling than metal electrodes, and these characteristics lead to improved electrochemical performance and reduced noise at smaller electrode diameters. PEDOT:PSS coating reduces the impedances of metallic electrodes by up to 18x for diameters <200 µm, but has no effect for millimeter scale contacts due to the dominance of series resistances. Therefore, the performance gains are especially significant at smaller diameters and lower frequencies essential for recording cognitive and pathological activities. Additionally, the overall reduced noise of the PEDOT:PSS electrodes enables a lower noise floor for recording action potentials. These results permit quantitative optimization of contact material and diameter for different electrocorticography applications.     

Inkjet Printing of a Highly Loaded Palladium Ink for Integrated,Low‐Cost pH Sensors

An inkjet printing process for depositing palladium (Pd) thin films from a highly loaded ink (>14 wt%) is reported. The viscosity and surface tension of a Pd‐organic precursor solution is adjusted using toluene to form a printable and stable ink. A two‐step thermolysis process is developed to convert the printed ink to continuous and uniform Pd films with good adhesion to different substrates. Using only one printing pass, a low electrical resistivity of 2.6 μΩ m of the Pd film is obtained. To demonstrate the electrochemical pH sensing application, the surfaces of the printed Pd films are oxidized for ion‐to‐electron transduction and the underlying layer is left for electron conduction. Then, solid‐state reference electrodes are integrated beside the bifunctional Pd electrodes by inkjet printing. These potentiometric sensors have sensitivities of 60.6 ± 0.1 and 57 ± 0.6 mV pH^?1 on glass and polyimide substrates, and short response times of 11 and 6 s, respectively. Also, accurate pH values of real water samples are obtained by using the printed sensors with a low‐cost multimeter. These results indicate that the facile and cost‐effective inkjet printing and integration techniques may be applied in fabricating future electrochemical monitoring systems for environmental parameters and human health conditions.     

Cooperative Effect of GO and Glucose on PEDOT:PSS for High VOC and Hysteresis‐Free Solution‐Processed Perovskite Solar Cells

Hybrid organic–inorganic halide perovskites have emerged at the forefront of solution‐processable photovoltaic devices. Being the perovskite precursor mixture a complex equilibrium of species, it is very difficult to predict/control their interactions with different substrates, thus the final film properties and device performances. Here the wettability of CH₃NH₃PbI₃ (MAPbI₃) onto poly(3,4‐ethylenedioxythiophene):poly(styrenesulfonate) (PEDOT:PSS) hole transporting layer is improved by exploiting the cooperative effect of graphene oxide (GO) and glucose inclusion. The glucose, in addition, triggers the reduction of GO, enhancing the conductivity of the PEDOT:PSS+GO+glucose based nanocomposite. The relevance of this approach toward photovoltaic applications is demonstrated by fabricating a hysteresis‐free MAPbI₃ solar cells displaying a ≈37% improvement in power conversion efficiency if compared to a device grown onto pristine PEDOT:PSS. Most importantly, V_OC reaches values over 1.05 V that are among the highest ever reported for PEDOT:PSS p‐i‐n device architecture, suggesting minimal recombination losses, high hole‐selectivity, and reduced trap density at the PEDOT:PSS along with optimized MAPbI₃ coverage.     

Machine Learning‐Enabled Correlation and Modeling of Multimodal Response of Thin Film to Environment on Macro and Nanoscale Using “Lab‐on‐a‐Crystal”

To close the feedback loop between artificial intellegence‐controlled materials synthesis and characterization, material functionality must be rapidly tested. A platform for high‐throughput multifunctional materials characterization is developed using a quartz crystal microbalance with auxiliary in‐plane electrodes and a custom gas/vapor flow cell, enabling simultaneous scanning probe microscopy and electrical, optical, gravimetric, and viscoelastic characterization on the same film under controlled environment. The lab‐on‐a‐crystal in situ multifunctional output allows direct correlations between the gravimetric/viscoelastic, electrical, and optical responses of polymer film in response to environment. When multiple film properties are used to augment the training set for machine learning regression, prediction of material response to the environment improves by a factor of 13 when <5% of the total dataset is used for model training.     

3D‐Printed Soft Magnetoelectric Microswimmers for Delivery and Differentiation of Neuron‐Like Cells

Neurodegenerative diseases generally result in irreversible neuronal damage and neuronal death. Cell therapy shows promise as a potential treatment for these diseases. However, the therapeutic targeted delivery of these cells and the in situ provision of a suitable microenvironment for their differentiation into functional neuronal networks remain challenging. A highly integrated multifunctional soft helical microswimmer featuring targeted neuronal cell delivery, on‐demand localized wireless neuronal electrostimulation, and post‐delivery enzymatic degradation is introduced. The helical soft body of the microswimmer is fabricated by two‐photon lithography of the photocurable gelatin–methacryloyl (GelMA)‐based hydrogel. The helical body is then impregnated with composite multiferroic nanoparticles displaying magnetoelectric features (MENPs). While the soft GelMA hydrogel chassis supports the cell growth, and is degraded by enzymes secreted by cells, the MENPs allow for the magnetic transportation of the bioactive chassis, and act as magnetically mediated electrostimulators of neuron‐like cells. The unique combination of the materials makes these microswimmers highly integrated devices that fulfill several requirements for their future translation to clinical applications, such as cargo delivery, cell stimulation, and biodegradability. The authors envision that these devices will inspire new avenues for targeted cell therapies for traumatic injuries and diseases in the central nervous system.     

Screen‐Printed Poly(3,4‐Ethylenedioxythiophene):Poly(Styrenesulfonate) Grids as ITO‐Free Anodes for Flexible Organic Light‐Emitting Diodes

Poly(3,4‐ethylenedioxythiophene):poly(styrenesulfonate) (PEDOT: PSS) grids have been successfully constructed by roll‐to‐roll compatible screen‐printing techniques and have been used as indium tin oxide (ITO)‐free anodes for flexible organic light‐emitting diodes (OLEDs). The grid‐type transparent conductive electrodes (TCEs) can adopt thicker PEDOT: PSS grid lines to ensure the conductivity, while the mesh‐like grid structure can play an important role to maintain high optical transparency. By adjusting grid periods, grid thickness and treatment of organic additives, PEDOT: PSS TCEs with high optical transparency, low sheet resistance, and excellent mechanical flexibility have been achieved. Using the screen‐printed PEDOT: PSS grids as the anodes, ITO‐free OLEDs achieved peak current efficiency of 3.40 cd A^?1 at the current density of 10 mA cm^?2, which are 1.56 times better than the devices with ITO glass as the anodes. The improved efficiency is attributed to the light extraction effect and improved transparency by the grid structure. The superior optoelectronic performances of OLEDs based on flexible screen‐printed PEDOT: PSS grid anodes suggest their great prospects as ITO‐free anodes for flexible and wearable electronic applications.     

Tailoring Morphology and Structure of Inkjet‐Printed Liquid‐Crystalline Semiconductor/Insulating Polymer Blends for High‐Stability Organic Transistors

Inkjet printing of semiconducting polymers is desirable for realizing low‐cost, large‐area printed electronics. However, sequential inkjet printing methods often suffer from nozzle clogging because the solubility of semiconducting polymers in organic solvents is limited. Here, it is demonstrated that the addition of an insulating polymer to a semiconducting polymer ink greatly enhances the solubility and stability of the ink, leading to the stable ejection of ink droplets. This bicomponent blend comprising a liquid‐crystalline semiconducting copolymer, poly(didodecylquaterthiophene‐alt‐didodecylbithiazole) (PQTBTz‐C12), and an insulating commodity polymer, polystyrene, is extremely useful as a semiconducting layer in organic field‐effect transistors (OFETs), providing fine control over the phase‐separated morphology and structure of the inkjet‐printed film. Tailoring the solubility‐induced phase separation of the two components leads to a bilayer structure consisting of a polystyrene layer on the top and a highly crystalline PQTBTz‐C12 layer on the bottom. The blend film is used as the semiconducting layer in OFETs, reducing the semiconductor content to several tens of pictograms in a single device without degrading the device performance. Furthermore, OFETs based on the PQTBTz‐C12/polystyrene film exhibit much greater environmental and electrical stabilities compared to the films prepared from homo PQTBTz‐C12, mainly due to the self‐encapsulated structure of the blend film.     

Flexible pressure sensor with high sensitivity and fast response for electronic skin using near-field electrohydrodynamic direct writing

Electronic skin imitates the function of human skin. The flexible pressure sensor is an important sensor of electronic skin. Although the flexible pressure sensor has made some progress, electronic skin is still a challenging subject with good pressure resolution, high sensitivity, and fast response ability in biomedical, human motion detection, personal health monitoring, and other fields. The PEDOT:PSS/GR/SWCNTs multicomponent solution was directly written on the flexible PDMS substrate by the near-field electrohydrodynamic direct-writing method, a serpentine shaped pressure sensitive unit was prepared, which was encapsulated with the PDMS thin film, and the flexible pressure sensor was fabricated. The sensitivity of the flexible pressure sensor is about 0.39 kPa⁻¹ at 0–0.5 kPa and 1.04 kPa⁻¹ at 0.5–2.4 kPa, and the response/recovery speed is 75 ms/150 ms, respectively. The fabricated flexible pressure sensor can detect a small pressure of about 6.4 Pa. The experimental results show that the fabricated flexible pressure sensor has high sensitivity, fast response capability, and low detection limit. The flexible pressure sensor for electronic skin demonstrates good performance in the application of finger joint movement and word pronunciation recognition, which indicates that it has great potential application in human motion detection and personal health monitoring.