A Li–Al–O Solid‐State Electrolyte with High Ionic Conductivity and Good Capability to Protect Li Anode

Using a solid‐state electrolyte (SSE) to stabilize the Li metal anode is widely considered a promising route to develop next‐generation high energy density lithium batteries. Here, a new polycrystalline aluminate‐based SSE (named Li–Al–O SSE) with good capability is introduced to protect Li metal. The SSE is formed on the Li metal surface via a chemical reaction between LiOH and triethylaluminum (TEAL) with the existence of LiTFSI‐based electrolyte. It is a continuous film that consists of polycrystalline LiAlO₂, Li₃AlO₃, Al₂O₃, Li₂CO₃, LiF, and some organic compounds. Such Li–Al–O SSE possesses a room‐temperature ionic conductivity as high as 1.42 × 10^?4 S cm^?1. Meanwhile, it effectively protects the Li anode from the corrosion of H₂O, O₂, and organic solvent, and suppresses the growth of Li dendrite. With the protection of the Li–Al–O SSE, the cycle life of Li|Li symmetric cell and Li|O₂ cell is substantially elongated, indicating that the SSE exhibits an excellent protective effect under both inert and oxidizing circumstances.     

Solid‐State Plastic Crystal Electrolytes: Effective Protection Interlayers for Sulfide‐Based All‐Solid‐State Lithium Metal Batteries

All‐solid‐state lithium metal batteries (ASSLMBs) have attracted significant attention due to their superior safety and high energy density. However, little success has been made in adopting Li metal anodes in sulfide electrolyte (SE)‐based ASSLMBs. The main challenges are the remarkable interfacial reactions and Li dendrite formation between Li metal and SEs. In this work, a solid‐state plastic crystal electrolyte (PCE) is engineered as an interlayer in SE‐based ASSLMBs. It is demonstrated that the PCE interlayer can prevent the interfacial reactions and lithium dendrite formation between SEs and Li metal. As a result, ASSLMBs with LiFePO₄ exhibit a high initial capacity of 148 mAh g^?1 at 0.1 C and 131 mAh g^?1 at 0.5 C (1 C = 170 mA g^?1), which remains at 122 mAh g^?1 after 120 cycles at 0.5 C. All‐solid‐state Li‐S batteries based on the polyacrylonitrile‐sulfur composite are also demonstrated, showing an initial capacity of 1682 mAh g^?1. The second discharge capacity of 890 mAh g^?1 keeps at 775 mAh g^?1 after 100 cycles. This work provides a new avenue to address the interfacial challenges between Li metal and SEs, enabling the successful adoption of Li metal in SE‐based ASSLMBs with high energy density.     

A High‐Performance Graphene Oxide‐Doped Ion Gel as Gel Polymer Electrolyte for All‐Solid‐State Supercapacitor Applications

A high‐performance graphene oxide (GO)‐doped ion gel (P(VDF‐HFP)‐EMIMBF₄‐GO gel) is prepared by exploiting copolymer (poly(vinylidene fluoride‐hexafluoro propylene), P(VDF‐HFP)) as the polymer matrix, ionic liquid (1‐ethyl‐3‐methylimidazolium tetrafluoroborate, EMIMBF₄) as the supporting electrolyte, and GO as the ionic conducting promoter. This GO‐doped ion gel demonstrates significantly improved ionic conductivity compared with that of pure ion gel without the addition of GO, due to the homogeneously distributed GO as a 3D network throughout the GO‐doped ion gel by acting like a ion “highway” to facilitate the ion transport. With the incorporation of only a small amount of GO (1 wt%) in ion gel, there has been a dramatic improvement in ionic conductivity of about 260% compared with that of pure ion gel. In addition, the all‐solid‐state supercapacitor is fabricated and measured at room temperature using the GO‐doped ion gel as gel polymer electrolyte, which demonstrates more superior electrochemical performance than the all‐solid‐state supercapacitor with pure ion gel and the conventional supercapacitor with neat EMIMBF₄, in the aspect of smaller internal resistance, higher capacitance performance, and better cycle stability. These excellent performances are due to the high ionic conductivity, excellent compatibility with carbon electrodes, and long‐term stability of the GO‐doped ion gel.     

Intercalated Electrolyte with High Transference Number for Dendrite‐Free Solid‐State Lithium Batteries

Solid‐state lithium (Li) batteries using solid electrolytes and Li anodes are highly desirable because of their high energy densities and intrinsic safety. However, low ambient‐temperature conductivity and poor interface compatibility of solid electrolytes as well as Li dendrite formation cause large polarization and poor cycling stability. Herein, a high transference number intercalated composite solid electrolyte (CSE) is prepared by the combination of a solution‐casting and hot‐pressing method using layered lithium montmorillonite, poly(ethylene carbonate), lithium bis(fluorosulfonyl)imide, high‐voltage fluoroethylene carbonate additive, and poly(tetrafluoroethylene) binder. The electrolyte presents high ionic conductivity (3.5 × 10^?4 S cm^?1), a wide electrochemical window (4.6 V vs Li⁺/Li), and high ionic transference number (0.83) at 25 °C. In addition, a 3D Li anode is also fabricated via a facile thermal infusion strategy. The synergistic effect of high transference number intercalated electrolyte and 3D Li anode is more favorable to suppress Li dendrites in a working battery. The solid‐state batteries based on LiFePO₄ (Al₂O₃ @ LiNi_0.5Co_0.2Mn_0.3O₂), CSE, and 3D Li deliver admirable cycling stability with discharge capacity 145.9 mAh g^?1 (150.7 mAh g^?1) and capacity retention 91.9% after 200 cycles at 0.5 C (92.0% after 100 cycles at 0.2 C) at 25 °C. This work affords a splendid strategy for high‐performance solid‐state battery.     

High Energy Density All‐Solid‐State Batteries: A Challenging Concept Towards 3D Integration

Rechargeable all‐solid‐state batteries will play a key role in many autonomous devices. Planar solid‐state thin film batteries are rapidly emerging but reveal several drawbacks, such as a relatively low energy density and the use of highly reactive metallic lithium. In order to overcome these limitations a new 3D‐integrated all‐solid‐state battery concept with significantly increased surface area is presented. By depositing the active battery materials into high‐aspect ratio structures etched in, for example silicon, 3D‐integrated all‐solid‐state batteries are calculated to reach a much higher energy density. Additionally, by adopting novel high‐energy dense Li‐intercalation materials the use of metallic Lithium can be avoided. Sputtered Ta, TaN and TiN films have been investigated as potential Li‐diffusion barrier materials. TiN combines a very low response towards ionic Lithium and a high electronic conductivity. Additionally, thin film poly‐Si anodes have been electrochemically characterized with respect to their thermodynamic and kinetic Li‐intercalation properties and cycle life. The Butler‐Vollmer relationship was successfully applied, indicating favorable electrochemical charge transfer kinetics and solid‐state diffusion. Advantageously, these new Li‐intercalation anode materials were found to combine an extremely high energy density with fast rate capability, enabling future 3D‐integrated all‐solid‐state batteries.     

Enabling Stable Cycling of 4.2 V High‐Voltage All‐Solid‐State Batteries with PEO‐Based Solid Electrolyte

Poly(ethylene oxide) (PEO)‐based solid electrolytes are expected to be exploited in solid‐state batteries with high safety. Its narrow electrochemical window, however, limits the potential for high voltage and high energy density applications. Herein the electrochemical oxidation behavior of PEO and the failure mechanisms of LiCoO₂‐PEO solid‐state batteries are studied. It is found that although for pure PEO it starts to oxidize at a voltage of above 3.9 V versus Li/Li⁺, the decomposition products have appropriate Li⁺ conductivity that unexpectedly form a relatively stable cathode electrolyte interphase (CEI) layer at the PEO and electrode interface. The performance degradation of the LiCoO₂‐PEO battery originates from the strong oxidizing ability of LiCoO₂ after delithiation at high voltages, which accelerates the decomposition of PEO and drives the self‐oxygen‐release of LiCoO₂, leading to the unceasing growth of CEI and the destruction of the LiCoO₂ surface. When LiCoO₂ is well coated or a stable cathode LiMn_0.7Fe_0.3PO₄ is used, a substantially improved electrochemical performance can be achieved, with 88.6% capacity retention after 50 cycles for Li_1.4Al_0.4Ti_1.6(PO₄)₃ coated LiCoO₂ and 90.3% capacity retention after 100 cycles for LiMn_0.7Fe_0.3PO₄. The results suggest that, when paired with stable cathodes, the PEO‐based solid polymer electrolytes could be compatible with high voltage operation.     

Low Resistance–Integrated All‐Solid‐State Battery Achieved by Li7La3Zr2O12 Nanowire Upgrading Polyethylene Oxide (PEO) Composite Electrolyte and PEO Cathode Binder

All‐solid‐state lithium metal battery is the most promising next‐generation energy storage device. However, the low ionic conductivity of solid electrolytes and high interfacial impedance with electrode are the main factors to limit the development of all‐solid‐state batteries. In this work, a low resistance–integrated all‐solid‐state battery is designed with excellent electrochemical performance that applies the polyethylene oxide (PEO) with lithium bis(trifluoromethylsulphonyl)imide as both binder of cathode and matrix of composite electrolyte embedded with Li₇La₃Zr₂O₁₂ (LLZO) nanowires (PLLN). The PEO in cathode and PLLN are fused at high temperature to form an integrated all‐solid‐state battery structure, which effectively strengthens the interface compatibility and stability between cathode and PLLN to guarantee high efficient ion transportation during long cycling. The LLZO nanowires uniformly distributed in PLLN can increase the ionic conductivity and mechanical strength of composite electrolyte efficiently, which induces the uniform deposition of lithium metal, thereby suppressing the lithium dendrite growth. The Li symmetric cells using PLLN can stably cycle for 1000 h without short circuit at 60 °C. The integrated LiFePO₄/PLLN/Li batteries show excellent cycling stability at both 60 and 45 °C. The study proposed a novel and robust battery structure with outstanding electrochemical properties.     

Capacitive Enhancement Mechanisms and Design Principles of High‐Performance Graphene Oxide‐Based All‐Solid‐State Supercapacitors

Graphene oxide (GO)‐based all‐solid‐state supercapacitors (GO‐A3Ss) are superior over liquid electrolyte‐based supercapacitors and capable of being integrated on a single chip in various geometry shapes for the use of future smart wearable electronics field as a fast energy storage device, but their capacitance need to be improved. Here, a new approach has been developed for enhancing the capacitive capability of the supercapacitors through molecular dynamics simulations with the first‐principle input. A theoretical model of charge storage is developed to understand the unique capacitive enhancement mechanism and to predict the capacitance of the GO‐A3Ss, which agrees well with the experimental observations. A novel supercapacitor with GO and reduced graphene oxide (rGO) alternatively layered structures is designed based on the model, and its energy density is the highest among conventional supercapacitors using liquid electrolytes and all‐solid‐state supercapacitors using aerogels or hydrogels as the solid‐state electrolyte. Based on the predictions, two new types of high‐performance GO/rGO multilayered capacitors are proposed to meet different practical applications. The results of this work provide an approach for the design of high‐performance all‐solid‐state supercapacitors based on GO and rGO materials.     

Foldable All‐Solid‐State Supercapacitors Integrated with Photodetectors

Recent development in flexible electronics has promoted the increasing demand for their energy storage systems that will be lightweight, thin, flexible, and even foldable. Although various flexible supercapacitors recently have been successfully developed, the design and assembly of highly foldable supercapacitors have received less attention. Furthermore, foldable supercapacitors are in general operated independently with other electronics, resulting in some space and energy consumption from the external connection system. Therefore, the authors fabricate the foldable all‐solid‐state integrated devices with supercapacitor and photodetector functions in a simplified and compact configuration based on single‐walled carbon nanotube films and TiO₂ nanoparticles. The integrated devices not only retain the intrinsic capacitance behavior but also show excellent sensitivity of detecting white light. More importantly, the capacitance behavior of integrated devices remains almost unchanged and the photodetector behavior is quite stable even folded by 180° due to their unique integrated configuration. Such rational design of all‐solid‐state integrated devices will pave the way for assembling energy storage devices and other electronics into highly flexible and foldable integrated devices.     

Operando Differential Electrochemical Pressiometry for Probing Electrochemo‐Mechanics in All‐Solid‐State Batteries

Owing to an absence or lack of soft (and/or liquid) components, electrochemo‐mechanical effects are imperative for all‐solid‐state batteries (ASBs) based on inorganic solid electrolytes (SEs). As this aspect has been overlooked, relevant investigation has remained scarce. In this work, the development of a new operando differential electrochemical pressiometry (DEP) for ASBs is reported. The time‐ (or capacity‐) derivative differential pressure signals (dP/dt or dP/dQ) reflecting corresponding differential volume changes of electrode active materials feature the specific state of charges (SOCs). This finding leads to a precise estimation of the SOCs of graphite (Gr) electrodes in LiNi_0.70Co_0.15Mn_0.15O₂ (NCM)/Gr all‐solid‐state full cells using sulfide SEs with varying capacity ratios of negative to positive electrodes (n/p ratios); this is corroborated by complementary analysis using a three‐electrode electrochemical cell and ex situ X‐ray diffraction measurements. Furthermore, electrochemo‐mechanical behaviors of NCM/Gr full cells with Gr electrodes employing SEs excluding or including reductively unstable Li₁₀GeP₂S₁₂ are investigated. Notable volume changes caused by lithiation of Li₁₀GeP₂S₁₂ are detected. Importantly, significantly delayed SOC for Gr caused by a severe side reaction with Li₁₀GeP₂S₁₂ is disclosed by the operando DEP result.     

All‐Purpose Electrode Design of Flexible Conductive Scaffold toward High‐Performance Li–S Batteries

The main obstacles that hinder the development of efficient lithium sulfur (Li–S) batteries are the polysulfide shuttling effect in sulfur cathode and the uncontrollable growth of dendritic Li in the anode. An all‐purpose flexible electrode that can be used both in sulfur cathode and Li metal anode is reported, and its application in wearable and portable storage electronic devices is demonstrated. The flexible electrode consists of a bimetallic CoNi nanoparticle‐embedded porous conductive scaffold with multiple Co/Ni‐N active sites (CoNi@PNCFs). Both experimental and theoretical analysis show that, when used as the cathode, the CoNi and Co/Ni‐N active sites implanted on the porous CoNi@PNCFs significantly promote chemical immobilization toward soluble lithium polysulfides and their rapid conversion into insoluble Li₂S, and therefore effectively mitigates the polysulfide shuttling effect. Additionally, a 3D matrix constructed with porous carbonous skeleton and multiple active centers successfully induces homogenous Li growth, realizing a dendrite‐free Li metal anode. A Li–S battery assembled with S/CoNi@PNCFs cathode and Li/CoNi@PNCFs anode exhibits a high reversible specific capacity of 785 mAh g^?1 and long cycle performance at 5 C (capacity fading rate of 0.016% over 1500 cycles).     

High Electroactive Material Loading on a Carbon Nanotube@3D Graphene Aerogel for High‐Performance Flexible All‐Solid‐State Asymmetric Supercapacitors

Freestanding carbon‐based hybrids, specifically carbon nanotube@3D graphene (CNTs@3DG) hybrid, are of great interest in electrochemical energy storage. However, the large holes (about 400 µm) in the commonly used 3D graphene foams (3DGF) constitute as high as 90% of the electrode volume, resulting in a very low loading of electroactive materials that is electrically connected to the carbon, which makes it difficult for flexible supercapacitors to achieve high gravimetric and volumetric energy density. Here, a hierarchically porous carbon hybrid is fabricated by growing 1D CNTs on 3D graphene aerogel (CNTs@3DGA) using a facile one‐step chemical vapor deposition process. In this architecture, the 3DGA with ample interconnected micrometer‐sized pores (about 5 µm) dramatically enhances mass loading of electroactive materials comparing with 3DGF. An optimized all‐solid‐state asymmetric supercapacitor (AASC) based on MnO₂@CNTs@3DGA and Ppy@CNTs@3DGA electrodes exhibits high volumetric energy density of 3.85 mW h cm^?3 and superior long‐term cycle stability with 84.6% retention after 20 000 cycles, which are among the best reported for AASCs with both electrodes made of pseudocapacitive electroactive materials.     

Design of a Multifunctional Interlayer for NASCION‐Based Solid‐State Li Metal Batteries

NASCION‐type Li conductors have great potential to bring high capacity solid‐state batteries to realization, related to its properties such as high ionic conductivity, stability under ambient conditions, wide electrochemical stability window, and inexpensive production. However, their chemical and thermal instability toward metallic lithium (Li) has severely hindered attempts to utilize Li as anode material in NASCION‐based battery systems. In this work, it is shown how a tailored multifunctional interlayer between the solid electrolyte and Li anode can successfully address the interfacial issues. This interlayer is designed by creating a quasi‐solid‐state paste in which the functionalities of LAGP (Li_1.5Al_0.5Ge_1.5(PO₄)₃) nanoparticles and an ionic liquid (IL) electrolyte are combined. In a solid‐sate cell, the LAGP‐IL interlayer separates the Li metal from bulk LAGP and creates a chemically stable interface with low resistance (≈5 Ω cm²) and efficiently prevents thermal runaway at elevated temperatures (300 °C). Solid‐state cells designed with the interlayer can be operated at high current densities, 1 mA cm^?2, and enable high rate capability with high safety. Here developed strategy provides a generic path to design interlayers for solid‐state Li metal batteries.     

High‐Performance All‐Solid‐State Cells Fabricated With Silicon Electrodes

All solid‐state thin‐film lithium microbatteries are a promising component able to fulfill most of the specific requirements to power autonomous microsystems. Nevertheless, metallic lithium, which is commonly used as the negative electrode in microbatteries, has a very low melting temperature (T_m = 181 °C) that appears to be incompatible with the solder‐reflow operation (maximum temperature T_max ≈ 260 °C) usually used to connect electronic components. Silicon is a promising candidate to replace lithium in solder‐reflowable lithium‐ion cells due to its high volumetric capacity (834 μAh cm^?2 μm^?1 for Li₁₅Si₄) and its ability to reversibly insert lithium at a low potential. Nevertheless, it suffers from a large volumetric expansion during lithium insertion (280%), which is partly responsible for a rapid capacity fading when cycled in liquid electrolyte. In this study, all‐solid‐state Li/LiPONB/Si cells are prepared using physical vapor deposition (PVD) techniques. The cycle life and the coulombic efficiency are found to be excellent in these solid‐state cells with almost no loss during 1500 cycles. Despite the large volume expansion due to lithium insertion confirmed by scanning electron microscopy, no evidence of cracks is found in the film or at the electrode/electrolyte interface, even after 1500 cycles.     

Shaping the Contact between Li Metal Anode and Solid‐State Electrolytes

Scientific and technological interest in solid‐state Li metal batteries (SSLMBs) arises from their excellent safety and promising high energy density. However, the practical application of SSLMBs is hindered by poor contact between the Li metal anode (LMA) and solid‐state electrolytes (SSEs). To circumvent this limitation, a pattern‐guided approach that shapes the LMA/SSE contact is disclosed to offer fast Li ion conduction in the interface. A thermally‐treated copper foam is used as the lithophilic pattern to confine and guide Li for forming a tight contact with garnet‐type SSE. The contact can be easily manipulated according to the shape of lithiophilic pattern, facilitating cell assembly. The resulting Li|patterned garnet|Li symmetric cell exhibits an interfacial resistance of 9.8 Ω cm², which is dramatically lower than that of 998 Ω cm² for Li|pristine garnet|Li symmetric cell. Being used in Li–sulfur batteries, the patterned garnet effectively eliminates the polysulfide shuttle and enables stable cycling performance, showing a low capacity decay of 0.035% per cycle over 1000 cycles. The fundamental contact process of metallic anodes/SSEs is carefully investigated. This contact strategy provides a new design concept to improve the interface wettability via a lithiophilic pattern for a variety of SSEs that cannot wet with metallic anodes.     

General Method for Large‐Area Films of Carbon Nanomaterials and Application of a Self‐Assembled Carbon Nanotube Film as a High‐Performance Electrode Material for an All‐Solid‐State Supercapacitor

Rational assembly of carbon nanostructures into large‐area films is a key step to realize their applications in ubiquitous electronics and energy devices. Here, a self‐assembly methodology is devised to organize diverse carbon nanostructures (nanotubes, dots, microspheres, etc.) into homogeneous films with potentially infinite lateral dimensions. On the basis of studies of the redox reactions in the systems and the structures of films, the spontaneous deposition of carbon nanostructures onto the surface of the copper substrate is found to be driven by the electrical double layer between copper and solution. As a notable example, the as‐assembled multiwalled carbon nanotube (MWCNT) films display exceptional properties. They are a promising material for flexible electronics with superior electrical and mechanical compliance characteristics. Finally, two kinds of all‐solid‐state supercapacitors based on the self‐assembled MWCNT films are fabricated. The supercapacitor using carbon cloth as the current collector delivers an energy density of 3.5 Wh kg^?1 and a power density of 28.1 kW kg^?1, which are comparable with the state‐of‐the‐art supercapacitors fabricated by the costly single‐walled carbon nanotubes and arrays. The supercapacitor free of foreign current collector is ultrathin and shows impressive volumetric energy density (0.58 mWh cm^?3) and power density (0.39 W cm^?3) too.     

Ultralight and Binder‐Free All‐Solid‐State Flexible Supercapacitors for Powering Wearable Strain Sensors

Flexible energy storage devices play a pivotal role in realizing the full potential of flexible electronics. This work presents high‐performance, all‐solid‐state, flexible supercapacitors by employing an innovative multilevel porous graphite foam (MPG). MPGs exhibit superior properties, such as large specific surface area, high electric conductivity, low mass density, high loading efficiency of pseudocapacitive materials, and controlled corrugations for accommodating mechanical strains. When loaded with pseudocapacitive manganese oxide (Mn₃O₄), the MPG/Mn₃O₄ (MPGM) composites achieve a specific capacitance of 538 F g^?1 (1 mV s^?1) and 260 F g^?1 (1 mV s^?1) based on the mass of pure Mn₃O₄ and entire electrode composite, respectively. Both are among the best of Mn₃O₄‐based supercapacitors. The MPGM is mechanically robust and can go through 1000 mechanical bending cycles with only 1.5% change in electric resistance. When integrated as all‐solid‐state symmetric supercapacitors, they offer a full cell specific capacitance as high as 53 F g^?1 based on the entire electrode and retain 80% of capacitance after 1000 continuous mechanical bending cycles. Furthermore, the all‐solid‐state flexible supercapacitors are incorporated with strain sensors into self‐powered flexible devices for detection of both coarse and fine motions on human skins, i.e., those from finger bending and heart beating.     

Electrolyte‐Regulated Solid‐Electrolyte Interphase Enables Long Cycle Life Performance in Organic Cathodes for Potassium‐Ion Batteries

Organic cathode materials as economical and environment‐friendly alternatives to inorganic cathode materials have attracted comprehensive attention in potassium‐ion batteries (KIBs). Nonetheless, active material dissolution and mismatched electrolytes result in insufficient cycle life that definitely hinders their practical applications. Here, a significantly improved cycle life of 1000 cycles (80% capacity retention) on a practically insoluble organic cathode material, anthraquinone‐1,5‐disulfonic acid sodium salt, is realized, in KIBs through a solid‐electrolyte interphase (SEI) regulation strategy by ether‐based electrolytes. Such an excellent performance is attributed to the robust SEI film and fast reaction kinetics. More importantly, the ether‐electrolyte‐derived SEI film has a protective inorganic‐rich inner layer arising from the prior decomposition of potassium salts to solvents, as revealed by X‐ray photoelectron spectroscopy analysis and computational studies on molecular orbital energy levels. The findings shed light on the critical roles of electrolytes and the corresponding SEI films in enhancing performance of organic cathodes in KIBs.