Measurements of the effective mass transfer areas for the gas–liquid rotating packed bed

Rotating packed bed(RPB) is one of the most effective gas–liquid mass transfer enhancement reactors, its effective specific mass transfer area(ae) is critical to understand the mass transfer process. By using the NaOH–CO₂ chemical absorption method, the aevalues of three RPB reactors with different rotor sizes were measured under different operation conditions. The results showed that the high gravity factor and liquid flow rate were major affecting factors, while the gas flow rate ex...     

整体式床层中液体分布与气-液传质的关系

With a particular focus on the connection between liquid flow distribution and gas-liquid mass transfer in monolithic beds in the Taylor flow regime, hydrodynamic and gas-liquid mass transfer experiments were carried out in a column with a monolithic bed of cell density of 50 cpsi with two different distributors (nozzle and packed bed distributors). Liquid saturation in individual channels was measured by using self-made micro-conductivity probes. A mal-distribution factor was used to evaluate uniform degree of phase distribution in monoliths. Overall bed pressure drop and mass transfer coefficients were measured. For liquid flow distribution and gas-liquid mass transfer, it is found that the superficial liquid velocity is a crucial factor and the packed bed distributor is better than the nozzle distributor. A semi-theoretical analysis using single channel models shows that the packed bed distributor always yields shorter and uniformly distributed liquid slugs compared to the nozzle distributor, which in turn ensures a better mass transfer performance. A bed scale mass transfer model is proposed by employing the single channel models in individual channels and incorporating effects of non-uniform liquid distribution along the bed cross-section. The model predicts the overall gas-liquid mass transfer coefficient with a relative error within ±30%.     

Mass transfer performance of structured packings in a CO2 absorption tower

This paper studies the mass transfer performance of structured packings in the absorption of CO2 from air with aqueous NaOH solution. The Eight structured packings tested are sheet metal ones with corrugations of different geometry parameters. Effective mass transfer area and overall gas phase mass transfer coefficient have been measured in an absorption column of 200 mm diameter under the conditions of gas F-factor in 0.38–1.52 Pa0.5 and aqueous NaOH solution concentration of 0.10–0.15 kmol·m?3. The effects of gas/liquid phase flow rates and packing geometry parameters are also investigated. The results show that the effective mass transfer area changes not only with packing geometry parameters and liquid load, but also with gas F-factor. A new effective mass transfer area correlation on the gas F-factor and the liquid load was proposed, which is found to fit experiment data very well.     

Simulation of the hydrodynamics and mass transfer in a falling film wavy microchannel

The flow in a liquid falling film is predominantly laminar, and the liquid-side mass transfer is limited by molecular diffusion. The effective way to enhance the mass transfer is to improve the liquid film flow behavior. The falling film behaviors of water, ethanol and ethylene glycol in nine different wavy microchannels were simulated by Computational Fluid Dynamics. The simulation results show that the falling film thickness exhibits a waveform distribution resulting in a resonance phenomenon along the wavy microchannel. The fluctuation of liquid film surface increases the gas–liquid interface area, and the internal eddy flow inside the liquid film also improves the turbulence of liquid film, the gas–liquid mass transfer in falling film microchannels is intensified. Compared with flat microchannel, the CO_2 absorption efficiency in water in the wavy microchannel is improved over 41%. Prediction models of liquid film amplitude and average liquid film thickness were established respectively.     

并流喷射填料塔板流体力学及传质性质性能的实验研究

The jet co-flow packing tray(JCPT) with three different types of perforation in equal opening fraction was tested in two rectangular columns with 0.12 m in width and 0.27 m in length operated with air-water system.The influences of gas phase orifice F-factor and clear liquid height He on the amount of liquid lifted, Q, were examined. The corresponding correlation between Q with F-factor and equivalent diameter of perforated holes as well as Hc was obtained. Furthermore, the non-steady state mass transfer performance of JCPT was tested by the humidification of air with water. Finally, by the analysis of data and comparison, it was found that the JCPT tray with single cap and two holes exhibited the highest mass transfer efficiency and best performance.     

Experimental determination of gas holdup and volumetric mass transfer coefficient in a jet bubbling reactor

The hydrodynamics and mass transfer characteristics of a lab-scale jet bubbling reactor(JBR) including the gas holdup, volumetric mass transfer coefficient and specific interfacial area were assessed experimentally investigating the influence of temperature, p H and superficial gas velocity. The reactor diameter and height were 11 and 30 cm,respectively. It was equipped with a single sparger, operating at atmospheric pressure, 20 and 40℃, and two p H values of 3 and 6. The height of the liquid was 23 cm, while the superficial gas velocity changed within 0.010–0.040 m·s~(-1) range. Experiments were conducted with pure oxygen as the gas phase and saturated lime solution as the liquid phase. The liquid-side volumetric mass transfer coefficient was determined under unsteady-state oxygen absorption in a saturated lime solution. The gas holdup was calculated based on the liquid height change, while the specific interfacial area was obtained by a physical method based on the bubble size distribution(BSD) in different superficial gas velocities. The results indicated that at the same temperature but different p H, the gas holdup variation was negligible, while the liquid-side volumetric mass transfer coefficient at the p H value of 6 was higher than that at the p H = 3. At a constant p H but different temperatures, the gas holdup and the liquid-side volumetric mass transfer coefficients at 40℃ were higher than that of the same at 20℃. A reasonable and appropriate estimation of the liquid-side volumetric mass transfer coefficient(kla) in a pilot-scale JBR was provided which can be applied to the design and scale-up of JBRs.     

An optimization method for enhancement of gas–liquid mass transfer in a bubble column reactor based on the entropy generation extremum principle

In this study, an optimization method is proposed to enhance the gas–liquid mass transfer in bubble column reactor based on the entropy generation extremum principle. The mass transfer–induced entropy generation can be maximized with the increase of mass transfer rate, based on which the velocity field can be optimized. The oxygen gas–liquid mass transfer is the major rate–limiting step of the toluene emissions biodegradation process in bubble column reactor, so the entropy generation due to oxy...     

Process intensification in vapor–liquid mass transfer: The state-of-the-art

The concept of process intensification(PI) has absorbed diverse definitions and stays true to the mission—"do more with less", which is an approach purposed by chemical engineers to solve the global energy environment problems. To date, the focus of PI has been on processes mainly involving vapor/liquid systems. Based on the fundamental principles of vapor–liquid mass transfer process like distillation and absorption, there are three strategies to intensify interphase mass transfer: enhancing the overall driving force, improving the mass transfer coefficient and enlarging the vapor–liquid interfacial area. More specifically, this article herein provides an overview of various technologies to strengthen the vapor–liquid mass transfer, including application of external fields, addition of third substances, micro-chemical technology and usage of solid foam, with the objective to contribute to the future developments and potential applications of PI in scientific research and industrial sectors.     

Mass transfer area in a multi-stage high-speed disperser with split packing

In this study, the mean droplet diameter in the cavity zone and the total mass transfer area of a multi-stage highspeed disperser(HSD) reactor with different packing combinations were measured and evaluated. The effects of rotational speed and packing radius, as well as the packing ring radius and numbers, on the mean droplet diameter and the total mass transfer area were evaluated. A model was established to calculate the mass transfer area in the cavity zone in the HSD reactor, and it was found that the packings contribute 61%–82% of the total mass transfer area. A correlation for predicting the mass transfer area in the packing zone was regressed by the dimensionless analysis method. An enhancement factor based on the mass transfer area in the packing zone was proposed to evaluate the effect of packing combination on mass transfer area. Two optimum packing combinations were proposed in consideration of the mean droplet diameter and the enhancement factor.     

折流式旋转床的流体力学行为(英文)

As a high gravity (HIGEE) unit, the rotating packed bed (RPB) uses centrifugal force to intensify mass transfer. Zigzag rotating bed (RZB) is a new type of HIGEE unit. The rotor of RZB consists of stationary discs and rotating discs, forming zigzag channels for liquid-gas flow and mass transfer. As in RPBs, some hydrodynamic behavior in RZB is interesting but no satisfactory explanation. In this study, the experiments were carried on in a RZB unit with a rotor of 600 mm in diameter using air-water system. The gas pressure drop and power consumption were measured with two types of rotating baffle for RZB rotors, one with perforations and another with shutter openings. The circumferential velocities of gas were measured with a five-hole Pitot probe. The pressure drop decreased rapidly when the liquid was introduced to the rotor, because the circumferential velocity of the liquid droplets was lower than that of the gas, reducing the circumferential velocity of gas and the centrifugal pressure drop. The power consumption decreased first when the gas entered the RZB rotor, because the gas with higher circumferential velocity facilitates the rotation of baffles.     

新一代的乱堆填料——梅花扁环

The hydrodynamics and mass transfer of Plum Flower Mini Ring(PFMR),Pall Ring and Intalox Saddle were studied in a 600mm diameter column with air-oxygen-water system over a wide range of liquid loasds.It was shown from the experiments that PFMR had much lower resistance,larger throughput and higher mass transfer efficiency than Pall Ring and Intalox Saddle.It was clear from the comparison that existing equations could not predict the performance of packings very well at high liquied loads.Therefore,new semi-empirical equations of pressure drop,flooding gas velocity and height of transfer unit(HTU)were proposed based on the experimental data.     

Mass transfer characteristics in a rotating packed bed with split packing

The rotating packed bed (RPB) with split packing is a novel gas–liquid contactor, which intensifies the mass transfer processes controlled by gas-side resistance. To assess its efficacy, the mass transfer characteristics with adjacent rings in counter-rotation and co-rotation modes in a split packing RPB were studied experimentally. The physical absorption system NH3–H2O was used for characterizing the gas volumetric mass transfer coeffi-cient (kyae) and the effective interfacial area (ae) was determined by chemical absorption in the CO2–NaOH sys-tem. The variation in kyae and ae with the operating conditions is also investigated. The experimental results indicated that kyae and ae for counter-rotation of the adjacent packing rings in the split packing RPB were higher than those for co-rotation, and both counter-rotation and co-rotation of the split packing RPB were superior over conventional RPBs under the similar operating conditions.     

翅片导流板填料应用于旋转填料床的特性

For an alcohol/water system and with fin baffle packing, continuous distillation experiments were carried out in a rotating packed bed (RPB) system at atmospheric pressure. The effects of the average high gravity factor (β), liquid reflux ratio (R) and feedstock flux (F) on the momentum transfer and mass transfer were investigated. The gas phase pressure drop of RPB increased with the average high gravity factor, liquid reflux ratio and feedstock flux, which was 13.55-64.37 Pa at β of 2.01-51.49, R of 1.0-2.5, and F of 8-24 L&;#8226;h－1 for a theoretical tray in the RPB with fin baffle packing. The investigation on the mass transfer in the RPB with different packings showed that the number of transfer units of RPB with a packing also increased with the average high gravity factor, reflux ratio and feedstock flux. It is found that the fin baffle packing (packing III) presents the best mass transfer performance and lowest pressure drop for the height equivalent to a theoretical plate (HETP), which is 6.59-9.84 mm.     

Convective Heat Transfer Enhancement of a Rectangular Flat Plate by an Impinging Jet in Cross Flow

Experiments were carried out to study the heat transfer performance of an impinging jet in a cross flow. Several parameters including the jet-to-cross-flow mass ratio （X=2%-8%）, the Reynolds number （Red=1434-5735） and the jet diameter （d=2-4 mm） were explored. The heat transfer enhancement factor was found to increase with the jet-to-cross-flow mass ratio and the Reynolds number, but decrease with the jet diameter when other parameters maintain fixed. The presence of a cross flow was observed to degrade the heat transfer performance in respect to the effect of impinging jet to the target surface only. In addition, an impinging jet was confirmed to be capable of en-hancing the heat transfer process in considerable amplitude even though the jet was not designed to impinge on the target surface.     

一串上升气泡周围流体的湍动特性(英文)

The turbulence behavior of gas-liquid two-phase flow plays an important role in heat transfer and mass transfer in many chemical processes. In this work, a 2D particle image velocimetry (PIV) was used to investigate the turbulent characteristic of fluid induced by a chain of bubbles rising in Newtonian and non-Newtonian fluids. The instantaneous flow field, turbulent kinetic energy (TKE) and TKE dissipation rate were measured. The results demonstrated that the TKE profiles were almost symmetrical along the column center and showed higher values in the central region of the column. The TKE was enhanced with the increase of gas flow and decrease of liquid viscosity. The maximum TKE dissipation rate appeared on both sides of the bubble chain, and increased with the increase of gas flow rate or liquid viscosity. These results provide an understanding for gas-liquid mass transfer in non-Newtonian fluids.     

Effects of rotor and stator geometry on dissolution process and power consumption in jet-flow high shear mixers

The jet-flow high shear mixer(JF-HSM)is a new type of intensified equipment with special configurations of the rotor and the stator.The mass transfer property and power consumption were studied in the solid-liquid system for a series of JF-HSMs involving different configuration parameters,such as rotor diameter,rotor blade inclination,rotor blade bending direction,stator diameter,and stator bottom opening diameter.The flow characteristics were examined by computational fluid dynamic simulations.Results indicate that the turbulent power consumption of the JF-HSM is affected by the change in rotor blade inclination and stator bottom opening.With the increase in the shear head size and the change in the rotor into a backward-curved blade,the solid-liquid mass transfer rate can be remarkably increased under the same input power.Dimensionless correlations for the mass transfer coefficient and power consumption were obtained to guide the scale-up design and selection of such a new type of equipment to intensify the overall mixing efficiency.     

Effect of Adsorbent Diameter on the Performance of Adsorption Refrigeration

Adsorbents are important components in adsorption refrigeration. The diameter of an adsorbent can af-fect the heat and mass transfer of an adsorber. The effect of particle diameter on effective thermal conductivity was investigated. The heat transfer coefficient of the refrigerant and the void rate of the adsorbent layer can also affect the effective thermal conductivity of adsorbents. The performance of mass transfer in the adsorber is better when pressure drop decreases. Pressure drop decreases with increasing permeability. The permeability of the adsorbent layer can be improved with increasing adsorbent diameter. The effect of adsorbent diameter on refrigeration output power was experimentally studied. Output power initially increases and then decreases with increasing diameter under different cycle time conditions. Output power increases with decreasing cycle time under similar diameters.     

Convective mass transfer enhancement in a membrane channel by delta winglets and their comparison with rectangular winglets☆

Numerical calculations were conducted to simulate the flow and mass transfer in narrow membrane channels equipped with delta winglets, which are often used as longitudinal vortex generators to enhance heat transfer in heat exchanger applications. The channel consists of an impermeable solid wall and a membrane. The delta winglets are attached to the solid wal surface to enhance the mass transfer near the membrane surface and sup-press the concentration polarization. The winglet performance was evaluated in terms of concentration polariza-tion factor versus consumed pumping power. Calculations were implemented for NaCl solution flow in a membrane channel having a height of 2.0 mm for Reynolds numbers ranging from 400 to 1000. The delta wing-lets were optimized under equal pumping power condition, and the results of optimization suggest winglet height of 5/6 of the channel height, aspect ratio of 2.0, attack angle of 30°, and a winglet interval equal to the chan-nel height. The optimal delta winglets were compared with the optimal rectangular winglets we found previous-ly, and it is shown that the rectangular winglets yield a somewhat better performance than the delta winglets. ? 2015 The Chemical Industry and Engineering Society of China, and Chemical Industry Press. Al rights reserved.     

CO2 absorption performance in a rotating disk reactor using DBU-glycerol as solvent

Gas–liquid mass transfer of rotating disk reactor was studied in CO_2 absorption using 1,8-diazabicyclo-[5.4.0]-undec-7-ene(DBU)-glycerol solution as solvent. Effects of the rotating disk structure and various operation parameters on the CO_2 absorption rate and CO_2 removal efficiency were investigated. The rotating disk with optimal holes is conducive to mass transfer of CO_2 and the formation of thin liquid film at the opening increases the gas–liquid contact area. With the increase of rotating speed, the liquid flow pattern on the rotating disk surface changes from thin film flow to separated streams and creates extra liquid lines attached to the rim of the disk,which leads to a very complicated change on the CO_2 absorption rate and CO_2 removal efficiency. The overall gas-phase mass transfer coefficient increases 138% as the rotating speed increasing from 250 to 1400 r·min~(-1).Increasing temperature from 298 to 338 K can enhance the CO_2 absorption rate due to lowering the viscosity of the solvent. The rate-determined step for the absorption is focused on the gas side. The rotating disk reactor can effectively enhance the absorption of CO_2 with viscous DBU-glycerol solvents.     

Investigation of extraction fraction in confined impinging jet reactors for tri-butyl-phosphate extracting butyric acid process☆

The extraction fraction E and overall volumetric mass transfer coefficient kLa of TBP extracting butyric acid pro-cess in confined impinging jet reactors (CIJR) with two jets were investigated. The main variables tested were the concentration of tri-butyl-phosphate (TBP) and butyric acid, the impinging velocity V, the impinging velocity ratio of two phases Vorg/Vaq, the nozzle inner diameter di and the distance L between the jet axes and the top wall of the impinging chamber. The results showed that E and kLa increase with an increase of the impinging ve-locity V, the concentration of TBP Corg, and the impinging velocity ratio Vorg/Vaq. However, E and kLa decrease with an increase of the inner diameter di from 1 to 2 mm, the concentration of butyric acid Caq from 0.5%(v/v) to 2%(v/v). The factor L ranging from 3 to 11 mm has a negligible effect on E and kLa. A correlation on these variables and kLa was proposed based on the experimental data. These results indicated good mass transfer performance of CIJR in the extraction operation.