Near-net-size preparation of porous mullite matrix ceramics with in situ formed 3D mullite whisker network

Porous mullite matrix ceramics have excellent thermal and mechanical properties suitable for applications such as in thermal insulation. However, their applications are limited by processing defects from nonuniform sintering shrinkage and the trade-off between high porosity (preferred for low thermal conductivity) and high mechanical strength. Herein, we seek to minimize the sintering shrinkage by near-net-size preparation and improve the strength by in situ formed whisker network structure. Gelcasting forming technology and pressureless sintering were used to prepare porous mullite matrix ceramics using kyanite and α-Al₂O₃ powders as the starting materials and using MoO₃ to promote the growth of mullite whiskers. The results showed that the sintering shrinkage could be compensated by the volume expansion from solid-state reaction during reaction sintering. The in situ formed three-dimensional (3D) whisker network further reduced sintering shrinkage and effectively improved the strength of the ceramics. An ultralow sintering shrinkage of .78% was achieved. The near-net-shape porous mullite matrix ceramics strengthened by 3D whisker network had a high porosity of 63.9%, a high compressive strength of 83.8 MPa and a high flexural strength of 53.5 MPa.     

Porous mullite ceramics with enhanced compressive strength from fly ash-based ceramic microspheres: Facile synthesis,structure, and performance

Porous mullite ceramics are widely used in heat insulation owing to their high temperature and corrosion resistant properties. Reducing the thermal conductivity by increasing porosity, while ensuring a high compressive strength, is vital for the synthesis of high-strength and lightweight porous mullite ceramics. In this study, ceramic microspheres are initially prepared from pre-treated high-alumina fly ash by spray drying, and then used to successfully prepare porous mullite ceramics with enhanced compressive strength via a simple direct stacking and sintering approach. The influence of sintering temperature and time on the microstructure and properties of porous mullite ceramics was evaluated, and the corresponding formation mechanism was elucidated. Results show that the porous mullite ceramics, calcined at 1550 °C for 3 h, possess a porosity of 47%, compressive strength of 31.4 MPa, and thermal conductivity of 0.775 W/(m?K) (at 25 °C), similar to mullite ceramics prepared from pure raw materials. The uniform pore size distribution and sintered neck between the microspheres contribute to the high compressive strength of mullite ceramics, while maintaining high porosity.     

Fabrication and properties of porous anorthite/mullite ceramics with both high porosity and high strength

Porous anorthite/mullite ceramics with both high porosity and high strength have been successfully fabricated by foam-gelcasting and pressureless sintering technology, using α-Al₂O₃, SiO₂, and CaCO₃ as starting materials and MnO₂ as sintering aids. The porous mullite ceramics prepared in this study had 83.3% porosity and 0.3 W/m·K thermal conductivity, exhibited compressive strength value as high as 6.1 MPa. The samples fabricated with mullite content of 30 mol% possessed 79.4% porosity and 5.9 MPa compressive strength showed thermal conductivity as low as 0.19 W/m·K. With the addition of MnO₂, the properties of the prepared materials varied slightly when mullite content changed in a large scale. The results showed that the addition of MnO₂ promoted the reaction, affected sintering and grain growth, and contributed to high strength and low-thermal conductivity.     

Preparation and properties of mullite-bonded porous fibrous mullite ceramics by an epoxy resin gel-casting process

Porous fibrous mullite ceramics with a narrow range of pore size distribution have been successfully prepared utilizing a near net-shape epoxy resin gel-casting process by using mullite fibers, Al₂O₃ and SiC as raw materials. The effects of sintering temperatures, different amounts of fibers and Y₂O₃ additive on the phase compositions, linear shrinkage, apparent porosity, bulk density, microstructure, compressive strength and thermal conductivity were investigated. The results indicated that mullite-bonded among fibers were formed in the porous fibrous mullite ceramics with a bird nest pore structure. After determining the sintering temperatures and the amount of fibers, the tailored porous fibrous mullite ceramics had a low linear shrinkage (1.36–3.08%), a high apparent porosity (61.1–71.7%), a relatively high compressive strength (4.4–7.6 MPa), a low thermal conductivity (0.378–0.467 W/m K) and a narrow range of pore size distribution (around 5 µm). The excellent properties will enable the porous ceramics as a promising candidate for the applications of hot gas filters, thermal insulation materials at high temperatures.     

Fabrication and properties of mullite fiber matrix porous ceramics by a TBA-based gel-casting process

A bird nest-like structure was designed by using the mullite fiber as the matrix and SiO₂ as the high temperature binder. This special material was successfully prepared by a TBA-based gel-casting process. The randomly arranged fiber laps bonded by SiO₂ binder was the most important structure characteristic of this porous material. The effect of sintering temperature on the properties, i.e. porosity, bulk density, linear shrinkage, compressive strength, thermal conductivity and the microstructure was studied. The composite exhibited significant pseudoductility. The fracture mechanism of this composite under compression was discussed. The results indicated that the sintering temperature ranging from 1500 to 1600 °C was suitable for yielding mullite fiber matrix porous ceramics which had a low thermal conductivity (0.19–0.22 W/m K), a relatively high compressive strength (3–13 MPa) and a high resilience (66–70%) for applications in the thermal insulators and high-temperature elastic seal field.     

Porous YSZ Ceramics Reinforced by Different Kinds of Fibers

Porous YSZ ceramics reinforced by different fibers were prepared by gel‐casting with 15% solid content and pressureless sintering. The four kinds of fibers (mullite, aluminosilicate, Al₂O₃, and YSZ fibers) were added into the YSZ ceramics with the same 10% vol content. After sintered at 1500°C for 2 h, aluminosilicate and mullite fibers could not be found in the samples of porous YSZ ceramics, which showed they reacted with YSZ ceramics at high temperature, while YSZ and Al₂O₃ fibers still kept perfect after sintering. Furthermore, the influences of fiber content, sintering temperature, porosity of matrix materials on compressive strength and porosity of the porous YSZ ceramics were studied. The results showed that Al₂O₃ fiber showed more obvious reinforcing effect than YSZ fiber on porous YSZ ceramics. The fiber‐reinforcing effects depend on fiber content, sintering temperature, and porosity of matrix materials. The fiber addition can improve the shrinkage behavior of porous ceramics during sintering and strengthen the skeleton of porous ceramics.     

Porous fibrous ZrO2-mullite ceramics prepared via tert-butyl alcohol-based gel-casting

Mullite fiber was used to fabricate ZrO₂-mullite based porous ceramic via tert-butyl alcohol (TBA)-based gel-casting process using zirconite and bauxite as raw materials. Phase compositions, microstructure, pore size distribution, linear shrinkage, bulk density, apparent porosity, thermal conductivity, and compressive strength were analyzed to investigate influences of mullite fiber content and added Y₂O₃ on prepared porous ceramics. Results show that bird nest-like three-dimensional fibrous reticular skeleton structure was constructed with mullite fibers that evenly enwrapped rod-like mullite and ZrO₂ grains. Prepared porous fibrous ZrO₂-mullite ceramics had narrow pore size distribution that consisted of mullite and m-ZrO₂. With an increase in mullite fiber content, linear shrinkage and bulk density decreased, apparent porosity increased, and relatively good thermal conductivity was obtained. In addition, added Y₂O₃ reacted with Al₂O₃ and SiO₂ to form Y-Al-Si-O glass phase, which promoted sintering and densification of the ceramic, thus improving its compressive strength.     

Preparation of Porous Mullite Ceramics Using Fly Ash Cenosphere as a Pore‐Forming Agent by Gelcasting Process

Porous mullite ceramics were fabricated from an industrial grade mullite powder by gelcasting process using fly ash cenospheres (FAC) as a pore‐forming agent. The influence of content of FAC and sintering temperature on the density and strength was evaluated. The microstructure showed that FAC can act as a sintering aid and a pore‐forming agent. When the sintering temperature at 1200°C, porous mullite ceramics with a relatively high porosity (48.1–72.2%), low density (0.84–1.64 g/cm³), low thermal conductivity (0.16–0.22 W/m · K), and high compressive strength (6.21–14.70 MPa) have been obtained.     

Controllable preparation of porous ZrB2–SiC ceramics via using KCl space holders

In this work, a novel and facile technique based on using KCl as space holders, along with partial sintering (at 1900 °C for 30 min), was explored to prepare porous ZrB₂–SiC ceramics with controllable pore structure, tunable compressive strength and thermal conductivity. The as-prepared porous ZrB₂–SiC samples possess high porosity of 45–67%, low average pore size of 3–7 μm, high compressive strength of 32–106 MPa, and low room temperature thermal conductivity of 13–34 W m⁻¹ K⁻¹. The porosity, pore structure, compressive strength and thermal conductivity of porous ZrB₂–SiC ceramics can be tuned simply by changing KCl content and its particle size. The effect of porosity and pore structure on the thermal conductivity of as-prepared porous ZrB₂–SiC ceramics was examined and found to be consistent with the classical model for porous materials. The poring mechanism of porous ZrB₂–SiC samples via adding pore-forming agent combined with partial sintering was also preliminary illustrated.     

Seed assisted in-situ synthesis of porous anorthite/mullite whisker ceramics by foam-freeze casting

Porous anorthite/mullite whisker ceramics with both high strength and low thermal conductivity have been successfully prepared by combining seed-assisted in situ synthesis and foam-freeze casting techniques. The addition of mullite seed was conducive to a reduction in the sintering shrinkage, pore size, and anorthite grain size. This increased the high aspect ratio of mullite whiskers, which enhanced the strength and diminished the thermal conductivity. Mullite whiskers overlapped to form a stable three-dimensional network structure similar to the bird's nest, which was also beneficial to heighten the mechanical properties of the prepared porous ceramics. Through this method, the prepared materials had a high apparent porosity of 87.7–90.2%, a low bulk density of 0.29–0.36 g/cm³, a high compressive strength of 0.65–3.31 MPa, and low thermal conductivity of 0.067–0.112 W/m·K. The results indicated that the method described here can fabricate porous ceramics with excellent properties for further thermal insulating applications.     

Ultra-low cost porous mullite ceramics with excellent dielectric properties and low thermal conductivity fabricated from kaolin for radome applications

Near-net-shape mullite ceramics with high porosity were prepared from ultra-low cost natural aluminosilicate mineral kaolin as raw material and polystyrene micro-sphere (PS) as pore-forming agent. Microstructure, flexural strength, thermal conductivity and dielectric properties of the ceramics were systematically researched. Results show that the porous mullite ceramics possess fibrous skeleton structure formed by a large quantity of interlocked mullite whiskers, which results in good mechanical properties and low-to-zero sintering shrinkage. Flexural strength of the porous mullite ceramics can be up to 41.01 ± 1.12 MPa, even if the porosity is as high as 62.44%. The dielectric constant and loss tangent of the porous mullite ceramics at room temperature are lower than 2.61 and 5.9 × 10⁻³, respectively. Besides, dielectric constant is very stable with the rising of temperature, and the dielectric loss can be consistently lower than 10⁻² when the temperature is not higher than 800 °C. In addition, thermal conductivity at room temperature is as low as 0.163 W/m/K when the porosity of mullite ceramics is 80.05%. The infiltration of SiO₂ aerogels (SiO₂ AGs) can further decrease the thermal conductivity to 0.075 W/m/K, while has just little effects on the dielectric properties. Excellent mechanical, thermal and dielectric properties show that the porous mullite ceramics have potential applications in radome fields. The porous mullite ceramics prepared from kaolin not only have low cost, but also can achieve near-net-shape.     

High gas permeability and directional channels of mullite porous ceramics prepared by pectin-based freeze-drying method

New gel system for preparing mullite porous ceramics by gel-casting freeze-drying was proposed, using pectin as gel source and alumina and silica as raw materials. Directional channels were formed due to sublimation of water during freeze-drying and decomposition of pectin during high temperature sintering to prepare porous mullite ceramic membranes. Effects of solid content on the properties of mullite ceramics in terms of phase composition, microstructure, apparent porosity, bulk density, pore size distribution, compressive strength, thermal conductivity, pressure drop, and gas permeability were investigated. It was found that prepared porous mullite possessed high apparent porosity (56.04%–75.34%), low bulk density (.77–1.37 g/cm³), uniform pore size distribution, relatively high compressive strength (.61–3.03 MPa), low thermal conductivity (.224–.329 W/(m·K)), high gas permeability coefficient (1.11 × 10⁻¹⁰–4.73 × 10⁻¹¹ m²), and gas permeance (2.18 × 10⁻²–9.32 × 10⁻³ mol⋅m⁻²⋅s⁻¹⋅Pa⁻¹). These properties make prepared lightweight mullite ceramic membranes promising for application in high temperature flue gas filtration. Proposed gel system is expected to provide a new route to prepare porous ceramics with high porosity and directional channels.     

In-situ growth of mullite whiskers and their effect on the microstructure and properties of porous mullite ceramics with an open/closed pore structure

Porous mullite ceramics with an open/closed pore structure were prepared by protein foaming method combined with fly ash hollow spheres. Both the open porosity and total porosity of samples were enhanced by increasing the hollow sphere content. Mullite whiskers with a diameter of 0.2–4 μm were grown in-situ in the porous mullite ceramics with an AlF₃ catalyst, conforming to a vapor-solid growth mechanism. The pore structure of the porous mullite ceramics was significantly affected by the mullite whiskers which increased the open porosity and total porosity. Moreover, the median pore size was reduced from 65.05 μm to 36.92 μm after the introduction of mullite whiskers. The flexural strength and the thermal conductivity of the samples decreased with increasing total porosity. The porosity dependence of the thermal conductivity was well described by the universal model, providing a reference for the prediction of thermal conductivity of porous ceramics with open/closed pores.     

Preparation and characterization of porous anorthite ceramics from red mud and fly ash

The porous anorthite ceramics with high porosity, good mechanical strength and low heat conductivity were prepared using red mud and fly ash as raw materials via the pore forming method. The effects of sintering temperature and fly ash on phase evolution, densification, compressive strength, thermal conductivity and microstructure of the ceramic materials were investigated. The results showed that the compressive strength of the porous ceramics had an obvious improvement with the increase in fly ash, and the densification and heat conductivity decreased firstly and then increased. In particular, specimen S2 containing 30 wt% red mud and 40 wt% fly ash sintered at 1150°C had the better performances. It had the water absorption of 18.18%, open porosity of 38.52%, bulk density of 1.29 g/cm³, compressive strength of 42.46 MPa, and heat conductivity of 1.24 W/m·K. X-ray diffraction analysis indicated that mullite, anorthite, α-quartz, and diopside ferrian were the dominant phases in the specimens. Scanning electron microscopy micrographs illustrated that plenty of open pores with strip shape and closed pores with axiolitic shape existed in the specimens. Furthermore, the existence of mullite could prevent crack propagation to enhance the energy of inter-granular fracture. It endowed the porous anorthite ceramics with high porosity, good compressive strength, and low heat conductivity.     

Effect of mullite phase formed in situ on pore structure and properties of high-purity mullite fibrous ceramics

Porous mullite ceramics are potential advanced thermal insulating materials. Pore structure and purity are the main factors that affect properties of these ceramics. In this study, high performance porous mullite ceramics were prepared via aqueous gel-casting using mullite fibers and kaolin as the raw materials and ρ-Al₂O₃ as the gelling agent. Effects of addition of mullite fibers on the pore structure and properties were examined. The results indicated that mullite phase in situ formed by kaolin, and ρ-Al₂O₃ ensured the purity of mullite samples and mullite fibers bonded together to form a nest-like structure, greatly improving the properties of ceramic samples. In particular, the apparent porosity of mullite samples reached 73.6%. In the presence of 75% of mullite fibers, the thermal conductivity was only 0.289 W/m K at room temperature. Moreover, the mullite samples possessed relatively high cold compressive strength in the range of 4.9–9.6 MPa. Therefore, porous mullite ceramics prepared via aqueous gel-casting could be used for wide applications in thermal insulation materials, attributing to the excellent properties such as high cold compressive strength and low thermal conductivity.     

Fabrication and characterization of anorthite–mullite–corundum porous ceramics from construction waste

In this work, anorthite–mullite–corundum porous ceramics were prepared from construction waste and Al₂O₃ powders by adding AlF₃ and MoO₃ as mineralizer and crystallization catalyst, respectively. The effects of the sintering temperature and time on open porosity, mechanical properties, pore size distribution, microstructure, and phase composition were characterized in detail. The results showed that the formation of the mullite whiskers and the properties of the anorthite–mullite–corundum porous ceramics depended more on the sintering temperature than the holding time. By co-adding 12 wt% AlF₃ and 4 wt% MoO₃, mullite whiskers were successfully obtained at sintering temperatures upon 1350 °C for 1 h. Furthermore, the resultant specimens exhibited excellent properties, including open porosity of 66.1±0.7%, biaxial flexural strength of 23.8±0.9 MPa, and average pore size of 1.32 µm (the corresponding cumulative volume percent was 37.29%).     

Effect of carbon content on electrical,thermal, and mechanical properties of porous SiC ceramics with B4C and C additives

The electrical, thermal, and mechanical properties of porous SiC ceramics with B₄C-C additives were investigated as functions of C content and sintering temperature. The electrical resistivity of porous SiC ceramics decreased with increases in C content and sintering temperature. A minimal electrical resistivity of 4.6 × 10^?2 Ω·cm was obtained in porous SiC ceramics with 1 wt% B₄C and 10 wt% C. The thermal conductivity and flexural strength increased with increasing sintering temperature and showed maxima at 4 wt% C addition when sintered at 2000 °C and 2100 °C. The thermal conductivity and flexural strength of porous SiC ceramics can be tuned independently from the porosity by controlling C content and sintering temperature. Typical electrical resistivity, thermal conductivity, and flexural strength of porous SiC ceramics with 1 wt% B₄C-4 wt% C sintered at 2100 °C were 1.3 × 10^?1 Ω·cm, 76.0 W/(m·K), and 110.3 MPa, respectively.     

Porous ceramics with near-zero shrinkage and low thermal conductivity from hazardous secondary aluminum dross

Herein, a simple, versatile, and low-cost approach has been proposed to realize the green utilization of secondary aluminum dross, the hazardous solid waste, namely directly sintering dry-pressed green bodies from secondary aluminum dross to fabricate porous ceramics according to high-temperature foaming process spontaneously without adding spare foaming agents. Aluminum nitride (AlN) in secondary aluminum dross was employed to realize high-temperature foaming due to its oxidation, which makes traditional AlN and salts removal process needless. Moreover, near-zero shrinkage or even expansion during sintering of porous ceramics have occurred because in-situ foaming process together with the oxidation of Al particles well offset the sintering shrinkage. After sintering at 1400°C for 2 h, porous ceramics composed of α-Al₂O₃ and spinel phases with open porosity of 37.91%, sintering expansion rate of 1.13%, flexural strength of 45.67 MPa, and thermal conductivity of 0.97 W/(m·K) have been prepared. Cenospheres as pore-forming agents have been added to further improve the porosity, and alumina-based porous ceramics with open porosity of 28.39%–43.20% and flexural strength of 15.80–52.48 MPa have been obtained. This effective solution for recycling secondary aluminum dross could supply high-performance porous ceramics, which is expected to be applied in the fields of light-weight structural components and thermal insulations.     

Effects of V2O5 addition on the synthesis of columnar self-reinforced mullite porous ceramics

Spearhead columnar mullite was synthesized by in-situ reaction with V₂O₅ as additive. When the content of V₂O₅ was 7 wt%, the length of the spearhead columnar mullite was the longest with an aspect ratio of about 3.5. Furthermore, columnar self-reinforced mullite porous ceramics were prepared by a foam-gelcasting method, and the effects of V₂O₅ content on the rheological and gelling properties of mullite slurries as well as the microstructure, physical property and thermal insulation property of the prepared mullite porous ceramics were studied. The results showed that the flexural strength and compressive strength of the porous ceramics with 63% porosity prepared by using 2 wt% V₂O₅ additive were respectively as high as 13.9 and 41.3 MPa, and the thermal conductivity was about 1.04 W m^?1 K^?1.     

Preparation of near net size porous alumina-calcium aluminate ceramics by gelcasting-pore-forming agent processs

In the processing of porous ceramics, shrinkage from green body to sintered compact during drying and sintering is one of the key concerns which affect microstructure and properties of porous ceramics. Through releasing gases from the burning of the pore forming agents, and volume expansion from the formation of low density resultants during sintering, the sintering shrinkage can be effectively compensated and near net size preparation can be achieved. Herein, near net size porous alumina-calcium aluminate ceramics with controllable shrinkage have been prepared using a combination of gelcasting and pore-forming agent process by adjusting the amount of CaCO₃ and polymethyl methacrylate (PMMA) microspheres added. Al₂O₃ and CaCO₃ were used as raw materials, PMMA microspheres were used as pore-forming agent, isobutylene/maleic anhydride copolymer (Isobam104) was used as gelling agent and dispersing agent. The effects of the addition amounts of CaCO₃ and PMMA in the slurry on the phase composition, shrinkage, porosity, and strength of porous alumina-calcium aluminate ceramics were investigated. The results show that as the CaCO₃ addition amount increases from 0 to 20 wt%, the shrinkage of the samples gradually decreases from 7.3% to −1.4%, and the consequent porosity increases from 58% to 66%, while the compressive strength increases from 5.9 to 15.5 MPa. When PMMA content increases from 10 to 50 wt%, the shrinkage of the samples decreases first and then increases, the porosity increases from 51% to 74%, and the compressive strength decreases from 12.5 to 5.3 MPa. The mechanisms for controlling shrinkages during preparation of porous alumina-calcium aluminate ceramics can be attributed to the following aspects: on one hand, gas release from burning of PMMA and decomposition of CaCO₃ during sintering; on the other hand, volume expansion due to the formation of lower density calcium aluminates which come from the reactions between CaO and Al₂O₃. The near net size preparation technique is of great significance for the manufacture of porous ceramics since the subsequent machining cost can be effectively reduced.