Effect of Na-addition on catalytic activity of Pt-ZSM-5 for low-temperature NO–H2–O2 reactions

The effect of additives on Pt-ZSM-5 catalysts was studied for the selective NO reduction by H₂ in the presence of excess O₂ (NO–H₂–O₂ reaction) at 100 °C. The reaction of NO in a stream of 0.08% NO, 0.28% H₂, 10% O₂, and He balance yielded N₂ with less than 10% selectivity, which could not be increased by changing Pt loading or H₂ concentration in the gas feed. Co-impregnation of NaHCO₃ and Pt onto ZSM-5 decreased the BET surface area and the Pt dispersion. Nevertheless, the Na-loaded catalyst (Na-Pt-ZSM-5) exhibited the higher NO_x conversion (>90%) and the N₂ selectivity (ca. 50%). Such a high catalytic activity even at high Na loadings (≥10 wt.%) is completely contrast to other Na-added Pt catalyst systems reported so far. Further improvement of N₂ selectivity was attained by the post-impregnation of NaHCO₃ onto Pt-ZSM-5. In situ DRIFT measurements suggested that the addition of Na promotes the adsorption of NO as NO₂⁻-type species, which would play a role of an intermediate to yield N₂. The introduction of Lewis base to the acidic supports including ZSM-5 would be applied to the catalyst design for selective NO–H₂–O₂ reaction at low temperatures.     

The activity and characterization of sol–gel Sn/Al2O3 catalyst for selective catalytic reduction of NOx in the presence of oxygen

Catalytic performance of Sn/Al₂O₃ catalysts prepared by impregnation (IM) and sol–gel (SG) method for selective catalytic reduction of NO_x by propene under lean burn condition were investigated. The physical properties of catalyst were characterized by BET, XRD, XPS and TPD. The results showed that NO₂ had higher reactivity than NO to nitrogen, the maximum NO conversion was 82% on the 5% Sn/Al₂O₃ (SG) catalyst, and the maximum NO₂ conversion reached nearly 100% around 425 °C. Such a temperature of maximum NO conversion was in accordance with those of NO_x desorption accompanied with O₂ around 450 °C. The activity of NO reduction was enhanced remarkably by the presence of H₂O and SO₂ at low temperature, and the temperature window was also broadened in the presence of H₂O and SO₂, however the NO_x desorption and NO conversion decreased sharply on the 300 ppm SO₂ treated catalyst, the catalytic activity was inhibited by the presence of SO₂ due to formation of sulfate species (SO₄²⁻) on the catalysts. The presence of oxygen played an essential role in NO reduction, and the activity of the 5% Sn/Al₂O₃ (SG) was not decreased in the presence of large oxygen.     

Low-temperature H2-SCR of NO on a novel Pt/MgO-CeO2 catalyst

The selective catalytic reduction of NO by H₂ under strongly oxidizing conditions (H₂-SCR) in the low-temperature range of 100–200 °C has been studied over Pt supported on a series of metal oxides (e.g., La₂O₃, MgO, Y₂O₃, CaO, CeO₂, TiO₂, SiO₂ and MgO-CeO₂). The Pt/MgO and Pt/CeO₂ solids showed the best catalytic behavior with respect to N₂ yield and the widest temperature window of operation compared with the other single metal oxide-supported Pt solids. An optimum 50 wt% MgO-50wt% CeO₂ support composition and 0.3 wt% Pt loading (in the 0.1–2.0 wt% range) were found in terms of specific reaction rate of N₂ production (mols N₂/g_cat s). High NO conversions (70–95%) and N₂ selectivities (80–85%) were also obtained in the 100–200 °C range at a GHSV of 80,000 h⁻¹ with the lowest 0.1 wt% Pt loading and using a feed stream of 0.25 vol% NO, 1 vol% H₂, 5 vol% O₂ and He as balance gas. Addition of 5 vol% H₂O in the latter feed stream had a positive influence on the catalytic performance and practically no effect on the stability of the 0.1 wt% Pt/MgO-CeO₂ during 24 h on reaction stream. Moreover, the latter catalytic system exhibited a high stability in the presence of 25–40 ppm SO₂ in the feed stream following a given support pretreatment. N₂ selectivity values in the 80–85% range were obtained over the 0.1 wt% Pt/MgO-CeO₂ catalyst in the 100–200 °C range in the presence of water and SO₂ in the feed stream. The above-mentioned results led to the obtainment of patents for the commercial exploitation of Pt/MgO-CeO₂ catalyst towards a new NO_x control technology in the low-temperature range of 100–200 °C using H₂ as reducing agent. Temperature-programmed desorption (TPD) of NO, and transient titration of the adsorbed surface intermediate NO_x species with H₂ experiments, following reaction, have revealed important information towards the understanding of basic mechanistic issues of the present catalytic system (e.g., surface coverage, number and location of active NO_x intermediate species, NO_x spillover).     

Catalytic effect of platinum on the kinetics of carbon oxidation by NO2 and O2

The effect of a commercial Pt/Al₂O₃ catalyst on the oxidation by NO₂ and O₂ of a model soot (carbon black) in conditions close to automotive exhaust gas aftertreatment is investigated. Isothermal oxidations of a physical mixture of carbon black and catalyst in a fixed bed reactor were performed in the temperature range 300–450 °C. The experimental results indicate that no significant effect of the Pt catalyst on the direct oxidation of carbon by O₂ and NO₂ is observed. However, in presence of NO₂–O₂ mixture, it is found that besides the well established catalytic reoxidation of NO into NO₂, Pt also exerts a catalytic effect on the cooperative carbon–NO₂–O₂ oxidation reaction. An overall mechanism involving the formation of atomic oxygen over Pt sites followed by its transfer to the carbon surface is established. Thus, the presence of Pt catalyst increases the surface concentration of –C(O) complexes which then react with NO₂ leading to an enhanced carbon consumption. The resulting kinetic equation allows to model more precisely the catalytic regeneration of soot traps for automotive applications.     

Potential rare-earth modified CeO2 catalysts for soot oxidation part II: Characterisation and catalytic activity with NO + O2

Ceria (CeO₂) and rare-earth modified ceria (CeReO_x with Re = La³⁺, Pr^3+/4+, Sm³⁺, Y³⁺) supports and Pt impregnated supports are studied for the soot oxidation under a loose contact with the catalyst with the feed gas, containing NO + O₂. The catalysts are characterised by XRD, H₂-TPR, DRIFT and Raman spectroscopy. Among the single component oxides, CeO₂ is significantly more active compared with the other lanthanide oxides used in this study. Doping CeO₂ with Pr^3+/4+ and La³⁺ improved, however, the soot oxidation activity of the resulting solid solutions. This improvement is correlated with the surface area in the case of CeLaO_x and to the surface area and redox properties of CePrO_x catalyst. The NO conversion to NO₂ over these catalysts is responsible for the soot oxidation activity. If the activity per unit surface area is compared CePrO_x is the most active one. This indicates that though La³⁺ can stabilise the surface area of the catalyst in fact it decreases the soot oxidation activity of Ce⁴⁺. The lattice oxygen participates in NO conversion to NO₂ and the rate of this lattice oxygen transfer is much faster on CePrO_x. In general, the improvement of the soot oxidation is observed over the Pt impregnated CeO₂ and CeReO_x catalysts, and can be correlated to the presence of Pt°. The surface reduction of the supports in the presence of Pt occurred below 100 °C. The surface redox properties of the support in the Pt catalysts do not have a significant role in the NO to NO₂ conversion. In spite of the lower surface area, the Pt/CeYO_x and Pt/CeO₂ catalysts are found to be more active due to larger Pt crystal sizes. The presence of Pt also improved the CO conversion to CO₂ over these catalysts. The activation energy for the soot oxidation with NO + O₂ is found to be around 50 kJ/mol.     

Quantified NOx adsorption on Pt/K/gamma-Al2O3 and the effects of CO2 and H2O

A multi-component NO_x-trap catalyst consisting of Pt and K supported on γ-Al₂O₃ was studied at 250 °C to determine the roles of the individual catalyst components, to identify the adsorbing species during the lean capture cycle, and to assess the effects of H₂O and CO₂ on NO_x storage. The Al₂O₃ support was shown to have NO_x trapping capability with and without Pt present (at 250 °C Pt/Al₂O₃ adsorbs 2.3 μmols NO_x/m²). NO_x is primarily trapped on Al₂O₃ in the form of nitrates with monodentate, chelating and bridged forms apparent in Diffuse Reflectance mid-Infrared Fourier Transform Spectroscopy (DRIFTS) analysis. The addition of K to the catalyst increases the adsorption capacity to 6.2 μmols NO_x/m², and the primary storage form on K is a free nitrate ion. Quantitative DRIFTS analysis shows that 12% of the nitrates on a Pt/K/Al₂O₃ catalyst are coordinated on the Al₂O₃ support at saturation.

When 5% CO₂ was included in a feed stream with 300 ppm NO and 12% O₂, the amount of K-based nitrate storage decreased by 45% after 1 h on stream due to the competition of adsorbed free nitrates with carboxylates for adsorption sites. When 5% H₂O was included in a feed stream with 300 ppm NO and 12% O₂, the amount of K-based nitrate storage decreased by only 16% after 1 h, but the Al₂O₃-based nitrates decreased by 92%. Interestingly, with both 5% CO₂ and 5% H₂O in the feed, the total storage only decreased by 11%, as the hydroxyl groups generated on Al₂O₃ destabilized the K–CO₂ bond; specifically, H₂O mitigates the NO_x storage capacity losses associated with carboxylate competition.     

Combined effect of H2O and SO2 on V2O5/AC catalysts for NO reduction with ammonia at lower temperatures

Combined effect of H₂O and SO₂ on V₂O₅/AC the activity of catalyst for selective catalytic reduction (SCR) of NO with NH₃ at lower temperatures was studied. In the absence of SO₂, H₂O inhibits the catalytic activity, which may be attributed to competitive adsorption of H₂O and reactants (NO and/or NH₃). Although SO₂ promotes the SCR activity of the V₂O₅/AC catalyst in the absence of H₂O, it speeds the deactivation of the catalyst in the presence of H₂O. The dual effect of SO₂ is attributed to the SO₄²⁻ formed on the catalyst surface, which stays as ammonium-sulfate salts on the catalyst surface. In the absence of H₂O, a small amount of ammonium-sulfate salts deposits on the surface of the catalyst, which promote the SCR activity; in the presence of H₂O, however, the deposition rate of ammonium-sulfate salts is much greater, which results in blocking of the catalyst pores and deactivates the catalyst. Decreasing V₂O₅ loading decreases the deactivation rate of the catalyst. The catalyst can be used stably at a space velocity of 9000 h⁻¹ and temperature of 250 °C.     

The effect of oxygen concentration on the reduction of NO with propylene over CuO/γ-Al2O3

The effect of oxygen concentration on the pulse and steady-state selective catalytic reduction (SCR) of NO with C₃H₆ over CuO/γ-Al₂O₃ has been studied by infrared spectroscopy (IR) coupled with mass spectroscopy studies. IR studies revealed that the pulse SCR occurred via (i) the oxidation of Cu⁰/Cu⁺ to Cu²⁺ by NO and O₂, (ii) the co-adsorption of NO/NO₂/O₂ to produce Cu²⁺(NO₃⁻)₂, and (iii) the reaction of Cu²⁺(NO₃⁻)₂ with C₃H₆ to produce N₂, CO₂, and H₂O. Increasing the O₂/NO ratio from 25.0 to 83.4 promotes the formation of NO₂ from gas phase oxidation of NO, resulting in a reactant mixture of NO/NO₂/O₂. This reactant mixture allows the formation of Cu²⁺(NO₃⁻)₂ and its reaction with the C₃H₆ to occur at a higher rate with a higher selectivity toward N₂ than the low O₂/NO flow. Both the high and low O₂/NO steady-state SCR reactions follow the same pathway, proceeding via adsorbed C₃H₇---NO₂, C₃H₇---ONO, CH₃COO⁻, Cu⁰---CN, and Cu⁺---NCO intermediates toward N₂, CO₂, and H₂O products. High O₂ concentration in the high O₂/NO SCR accelerates both the formation and destruction of adsorbates, resulting in their intensities similar to the low O₂/NO SCR at 523–698 K. High O₂ concentration in the reactant mixture resulted in a higher rate of destruction of the intermediates than low O₂ concentration at temperatures above 723 K.     

Potential rare-earth modified CeO2 catalysts for soot oxidation: Part III. Effect of dopant loading and calcination temperature on catalytic activity with O2 and NO + O2

CeO₂ and CeReO_x_y catalysts are prepared by the calcination at different temperatures (y = 500–1000 °C) and having a different composition (Re = La³⁺ or Pr^3+/4+_, 0–90 wt.%). The catalysts are characterised by XRD, H₂-TPR, Raman, and BET surface area. The soot oxidation is studied with O₂ and NO + O₂ in the tight and loose contact conditions, respectively. CeO₂ sinters between 800–900 °C due to a grain growth, leading to an increased crystallite size and a decreased BET surface area. La³⁺ or Pr^3+/4+ hinders the grain growth of CeO₂ and, thereby, improving the surface catalytic properties. Using O₂ as an oxidant, an improved soot oxidation is observed over CeLaO_x_y and CePrO_x_y in the whole dopant weight loading and calcination temperature range studied, compared with CeO₂. Using NO + O₂, the soot conversion decreased over CeLaO_x_y catalysts calcined below 800 °C compared with the soot oxidation over CeO₂_y. CePrO_x_y, on the other hand, showed a superior soot oxidation activity in the whole composition and calcination temperature range using NO + O₂. The improvement in the soot oxidation activity over the various catalysts with O₂ can be explained based on an improvement in the external surface area. The superior soot oxidation activity of CePrO_x_y with NO + O₂ is explained by the changes in the redox properties of the catalyst as well as surface area. CePrO_x_y, having 50 wt.% of dopant, is found to be the best catalyst due to synergism between cerium and praseodymium compared to pure components. NO into NO₂ oxidation activity, that determines soot oxidation activity, is improved over all CePrO_x catalysts.     

Opposite activation conditions of acid and metal functions of Pt/SO4-ZrO2 catalysts

The influence of the thermal treatments of Pt/SO₄²⁻-Zr(OH)₄ catalysts on the activity for the metal-catalyzed reaction of cyclohexane dehydrogenation and the acid-catalyzed reaction of n-butane isomerization, were studied in this work. A mutual antagonism between the conditions for optimal activity of the acid and metal functions was found and was seemingly related to the crystallization of the support. In order to be able to isomerize n-butane, SO₄²⁻-Zr(OH)₄ had first to be calcined in air at T^calc>400 °C. The onset of activity and strong acid properties coincided with the appearance of the tetragonal crystal phase. SO₄²⁻-Zr(OH)₄ supported Pt, prepared from chloroplatinic acid, was tried to be converted to the metal state (Pt⁰) in order to have full catalytic capacity. When Pt/SO₄²⁻-Zr(OH)₄ was first calcined in air at T^calc>400 °C, Pt remained in a seemingly oxidized state, with no de/hydrogenation properties even after reduction in H₂ at 300 °C. Under certain conditions, Pt metal properties were improved: (i) calcining Pt/SO₄²⁻-Zr(OH)₄ in air at T^calc<400 °C; (ii) calcining Zr(OH)₄ at T^calc>400 °C before sulfating the support; and (iii) calcining Pt/SO₄²⁻-Zr(OH)₄ in N₂ instead of air. In these cases, though Pt dehydrogenation activity increased, the activity of the acid function decreased (iii) or was practically null ((i) and (ii)). The support was amorphous in case (i) and mainly monoclinic in case (ii). Sulfate loss and conversion into the monoclinic phase occurred in case (iii). As compared to sulfate-free Pt/ZrO₂, sulfur poisoning always decreased the metal activity of sulfated catalysts but the decrease was higher for mainly tetragonal sulfate-doped catalysts. The final conclusion is that the optimum activation conditions for the metal and acid functions in Pt/SO₄²⁻-Zr(OH)₄ are mutually excluding. The deleterious effect of SO₄²⁻-ZrO₂ (SZ) on Pt metal activity is closely related to the growth and/or the presence of the tetragonal phase and cannot be prevented if a high activity of the acid function is demanded by the reacting system.     

Effect of Pt on the water resistance of Co-zeolites upon the SCR of NOx with CH4

The objective of this work was to study the promotional effect of Pt on Co-zeolite (viz. mordenite, ferrierite, ZSM-5 and Y-zeolite) and Co/Al₂O₃ on the selective catalytic reduction (SCR) of NO_x with CH₄ under dry and wet reaction stream. After being reduced in H₂ at 350°C, the PtCo bimetallic zeolites showed higher NO to N₂ conversion and selectivity than the monometallic samples, as well as a combination of the latter samples such as mechanical mixtures or two-stage catalysts. After the same pretreatment, under wet reaction stream, the bimetallic samples were also more active. Among the other catalysts studied with 5% of water in the feed, (NO = CH₄ = 1000 ppm, O₂ = 2%), the NO conversion dropped to zero over Co_2.0Mor at 500°C and GHSV = 30,000 h⁻¹, whereas it is 20% in Pt_0.5Co_2.0Mor. In Pt/Co/Al₂O₃ the NO_x conversion dropped below 5% with only 2% of water under the same reaction conditions. The specific activity given as molecules of NO converted per total metal atom per second were 16.5 × 10⁻⁴ s⁻¹ for Pt_0.5Co_2.0Fer, 13 × 10⁻⁴ s⁻¹ for Pt_0.5Co_2.0Mor, 4.33 × 10⁻⁴ s⁻¹ for Pt_0.5Co_2.0ZSM-5 and 0.5 × 10⁻⁴ s⁻¹ for Pt/Co/Al₂O₃. The Y-zeolite-based samples were inactive in both mono and bimetallic samples. The species initially present in the solid were Pt° and Co°, together with Co²⁺ and Pt²⁺ at exchange positions. Co° seems not to participate as an active site in the SCR of NO_x. Those species remained after the reaction but some reorganization occurred. A synergetic effect among the different species that enhances both the NO to NO₂ reaction, the activation of CH₄ and also the ability of the catalyst to adsorb NO, could be responsible for the high activity and selectivity of the bimetallic zeolites.     

NO decomposition and reduction by CH4 over Sr/La2O3

Both NO decomposition and NO reduction by CH₄ over 4%Sr/La₂O₃ in the absence and presence of O₂ were examined between 773 and 973 K, and N₂O decomposition was also studied. The presence of CH₄ greatly increased the conversion of NO to N₂ and this activity was further enhanced by co-fed O₂. For example, at 773 K and 15 Torr NO the specific activities of NO decomposition, reduction by CH₄ in the absence of O₂, and reduction with 1% O₂ in the feed were 8.3·10⁻⁴, 4.6·10⁻³, and 1.3·10⁻² μmol N₂/s m², respectively. This oxygen-enhanced activity for NO reduction is attributed to the formation of methyl (and/or methylene) species on the oxide surface. NO decomposition on this catalyst occurred with an activation energy of 28 kcal/mol and the reaction order at 923 K with respect to NO was 1.1. The rate of N₂ formation by decomposition was inhibited by O₂ in the feed even though the reaction order in NO remained the same. The rate of NO reduction by CH₄ continuously increased with temperature to 973 K with no bend-over in either the absence or the presence of O₂ with equal activation energies of 26 kcal/mol. The addition of O₂ increased the reaction order in CH₄ at 923 K from 0.19 to 0.87, while it decreased the reaction order in NO from 0.73 to 0.55. The reaction order in O₂ was 0.26 up to 0.5% O₂ during which time the CH₄ concentration was not decreased significantly. N₂O decomposition occurs rapidly on this catalyst with a specific activity of 1.6·10⁻⁴ μmol N₂/s m² at 623 K and 1220 ppm N₂O and an activation energy of 24 kcal/mol. The addition of CH₄ inhibits this decomposition reaction. Finally, the use of either CO or H₂ as the reductant (no O₂) produced specific activities at 773 K that were almost 5 times greater than that with CH₄ and gave activation energies of 21–26 kcal/mol, thus demonstrating the potential of using CO/H₂ to reduce NO to N₂ over these REO catalysts.     

Kinetic studies of CH4 oxidation over Pt–NiO/δ-Al2O3 in a fluidised bed reactor

The oxidation of CH₄ over Pt–NiO/δ-Al₂O₃ has been studied in a fluidised bed reactor as part of a major project on an autothermal (combined oxidation–steam reforming) system for CH₄ conversion. The kinetic data were collected between 773 and 893 K and 101 kPa total pressure using CH₄ and O₂ compositions of 10–35% and 8–30%, respectively. Rate–temperature data were also obtained over alumina-supported monometallic catalysts, Pt and NiO. The bimetallic Pt–NiO system has a lower activation energy (80.8 kJ mol⁻¹) than either Pt (86.45 kJ mol⁻¹) and NiO (103.73 kJ mol⁻¹). The superior performance of the bimetallic catalyst was attributed to chemical synergy. The reaction rate over the Pt–NiO catalyst increased monotonically with CH₄ partial pressure but was inhibited by O₂. At low partial pressures (<30 kPa), H₂O has a detrimental effect on CH₄ conversion, whilst above 30 kPa, the rate increased dramatically with water content.     

The role of lanthana loading on the catalytic properties of Pd/Al2O3-La2O3 in the NO reduction with H2

The role of La₂O₃ loading in Pd/Al₂O₃-La₂O₃ prepared by sol–gel on the catalytic properties in the NO reduction with H₂ was studied. The catalysts were characterized by N₂ physisorption, temperature-programmed reduction, differential thermal analysis, temperature-programmed oxidation and temperature-programmed desorption of NO.

The physicochemical properties of Pd catalysts as well as the catalytic activity and selectivity are modified by La₂O₃ inclusion. The selectivity depends on the NO/H₂ molar ratio (GHSV = 72,000 h⁻¹) and the extent of interaction between Pd and La₂O₃. At NO/H₂ = 0.5, the catalysts show high N₂ selectivity (60–75%) at temperatures lower than 250 °C. For NO/H₂ = 1, the N₂ selectivity is almost 100% mainly for high temperatures, and even in the presence of 10% H₂O vapor. The high N₂ selectivity indicates a high capability of the catalysts to dissociate NO upon adsorption. This property is attributed to the creation of new adsorption sites through the formation of a surface PdO_x phase interacting with La₂O₃. The formation of this phase is favored by the spreading of PdO promoted by La₂O₃. DTA shows that the phase transformation takes place at temperatures of 280–350 °C, while TPO indicates that this phase transformation is related to the oxidation process of PdO: in the case of Pd/Al₂O₃ the O₂ uptake is consistent with the oxidation of PdO to PdO₂, and when La₂O₃ is present the O₂ uptake exceeds that amount (1.5 times). La₂O₃ in Pd catalysts promotes also the oxidation of Pd and dissociative adsorption of NO mainly at low temperatures (<250 °C) favoring the formation of N₂.     

Catalytic oxidation of HCN over a 0.5% Pt/Al2O3 catalyst

The adsorption of HCN on, its catalytic oxidation with 6% O₂ over 0.5% Pt/Al₂O₃, and the subsequent oxidation of strongly bound chemisorbed species upon heating were investigated. The observed N-containing products were N₂O, NO and NO₂, and some residual adsorbed N-containing species were oxidized to NO and NO₂ during subsequent temperature programmed oxidation. Because N-atom balance could not be obtained after accounting for the quantities of each of these product species, we propose that N₂ and was formed. Both the HCN conversion and the selectivity towards different N-containing products depend strongly on the reaction temperature and the composition of the reactant gas mixture. In particular, total HCN conversion reaches 95% above 250 °C. Furthermore, the temperature of maximum HCN conversion to N₂O is located between 200 and 250 °C, while raising the reaction temperature increases the proportion of NO_x in the products. The co-feeding of H₂O and C₃H₆ had little, if any effect on the total HCN conversion, but C₃H₆ addition did increase the conversion to NO and decrease the conversion to NO₂, perhaps due to the competing presence of adsorbed fragments of reductive C₃H₆. Evidence is also presented that introduction of NO and NO₂ into the reactant gas mixture resulted in additional reaction pathways between these NO_x species and HCN that provide for lean-NO_x reduction coincident with HCN oxidation.     

Regeneration of NOx trap catalysts

We have investigated the regeneration of a nitrated or sulphated model Pt/Ba-based NO_x trap catalyst using different reductants. H₂ was found to be more effective at regenerating the NO_x storage activity especially at lower temperature, but more importantly over the entire temperature window after catalyst ageing. When the model NO_x storage catalyst is sulphated in SO₂ under lean conditions at 650 °C almost complete deactivation can be seen. Complete regeneration was not achieved, even under rich conditions at 800 °C in 10% H₂/He. Barium sulphate formed after the high temperature ageing was partly converted to barium sulphide on reduction. However, if the H₂ reduced sample was exposed to a rich condition in a gas mixture containing CO₂ at 650 °C, the storage activity can be recovered. Under these rich conditions the S²⁻ species becomes less stable than the CO₃²⁻, which is active for storing NO_x. Samples which were lean aged in air containing 60 ppm SO₂ at <600 °C, after regeneration at λ=0.95 at 650 °C, have a similar activity window to a fresh catalyst. It is, therefore, important that CO₂ is present during the rich regenerations of the sulphated model samples (as of course it would be under real conditions), as suppression of carbonate formation can lead to sulphide formation which is inactive for NO_x storage.     

Catalytic reduction of NOx by hydrocarbons over Co/ZSM-5 catalysts prepared with different methods

Co/ZSM-5 catalysts were prepared by several methods, including wet ion exchange (WIE), its combination with impregnation (IMP), solid state ion exchange (SSI) and sublimation (SUB). FTIR results show that the zeolite protons in H-ZSM-5 are completely removed when CoCl₂ vapor is deposited. TPR shows peaks for Co²⁺ ions at 695–705°C and for Co₃O₄ at 385–390°C, but a peak in the 220–250°C region appears to indicate Co²⁺ oxo-ions.

The catalysts have been tested for the selective reduction of NO_x with iso-C₄H₁₀ under O₂-rich conditions and in the absence of O₂, both with dry and wet feeds. A bifunctional mechanism appears to operate at low temperature: oxo-ions or Co₃O₄ clusters first oxidize NO to NO₂, which is chemisorbed as NO_y (y≥2) and reduced. In this modus operandi catalyst SUB shows the highest N₂ yield 90% near 390°C for dry and wet feeds. It is found to be quite stable in a 52 h run with a wet feed. In contrast, the WIE catalyst, which mainly contains isolated Co²⁺ ions and has poor activity below 400°C, excels at T>430°C. This and the observation that, at high temperature, NO is reduced in O₂-free feeds over Co/MFI catalysts, suggest that NO can be reduced over Co²⁺ ions without intermediate formation of NO₂.

The bifunctional mechanism at low temperature is supported by the fact that a strongly enhanced performance is obtained by mixing WIE with Fe/FER, a catalyst known to promote NO₂ formation.     

Inhibition effect of H2O on V2O5/AC catalyst for catalytic reduction of NO with NH3 at low temperature

The inhibition effect of H₂O on V₂O₅/AC catalyst for NO reduction with NH₃ is studied at temperatures up to 250 °C through TPD, elemental analyses, temperature-programmed surface reaction (TPSR) and FT-IR analyses. The results show that H₂O does not reduce NO and NH₃ adsorption on V₂O₅/AC catalyst surface, but promotes NH₃ adsorption due to increases in Brønsted acid sites. Many kinds of NH₃ forms present on the catalyst surface, but only NH₄⁺ on Brønsted acid sites and a small portion of NH₃ on Lewis acid sites are reactive with NO at 250 °C or below, and most of the NH₃ on Lewis acid sites does not react with NO, regardless the presence of H₂O in the feed gas. H₂O inhibits the SCR reaction between the NH₃ on the Lewis acid sites and NO, and the inhibition effect increases with increasing H₂O content. The inhibition effect is reversible and H₂O does not poison the V₂O₅/AC catalyst.     

Reactivity of steam in exhaust gas catalysis III. Steam and oxygen/steam conversions of propane on a Pd/Al2O3 catalyst

A 1% Pd catalyst (38% dispersion) was prepared by impregnating a γ-alumina with palladium acetylacetonate dissolved in acetone. The behaviour of this catalyst in oxidation and steam reforming (SR) of propane was investigated. Temperature-programmed reactions of C₃H₈ with O₂ or with O₂ + H₂O were carried out with different stoichiometric ratios S(S =[O₂]/5[C₃H₈]). The conversion profiles of C₃H₈ for the reaction carried out in substoichiometry of O₂ (S < 1) showed two discrete domains of conversion: oxidation at temperatures below 350°C and SR at temperatures above 350°C. The presence of steam in the inlet gases is not necessary for SR to occur: there is sufficient water produced in the oxidation to form H₂ and carbon oxides by this reaction. Contrary to what was observed with Pt, an apparent deactivation between 310 and 385°C could be observed with Pd in oxidation. This is due to a reduction of PdO_x into Pd⁰, which is much less active than the oxide in propane oxidation. Steam added to the reactants inhibits oxidation while it prevents the reduction of PdO_x into Pd⁰. Compared to Pt and to Rh, Pd has a higher thermal resistance: no deactivation occurred after treatment up to 700°C and limited deactivation after treatment up to 900°C, provided that the catalyst is maintained in an oxygen-rich atmosphere during the cooling.     

On the mechanism of model diesel soot-O2 reaction catalysed by Pt-containing La-doped CeO2: A TAP study with isotopic O2

Pt supported on CeO₂ and 10 wt.% La³⁺-doped CeO₂ catalysts have been prepared, characterised and tested for soot oxidation by O₂ in TGA. The reaction mechanism has been studied in a TAP reactor with labelled O₂. Isotopic oxygen exchange between molecular O₂ and ‘O’ on the support/catalyst was observed and soot oxidation is being carried out by lattice oxygen. TAP studies further show that Pt improves O₂ adsorption and, therefore, 5 wt.% Pt-containing catalysts are more active for soot oxidation than the counterpart supports. In addition, CeO₂ doping by La³⁺ leads to an improved support, since La³⁺ stabilises the structure of CeO₂ when calcined at high temperature (1000 °C) and minimises sintering. In addition, La³⁺ improves the Ce⁴⁺/Ce³⁺ reduction as deduced from H₂-TPR experiments and favours oxygen mobility into the lattice. A synergetic effect of Pt and La³⁺ is observed, Pt-containing La³⁺-doped CeO₂ being the most active catalyst for soot oxidation by O₂ among the samples studied.