Oxygen mass transfer coefficient in bubble column slurry reactor with ultrafine suspended particles and neural network prediction

The gas–liquid volumetric mass transfer coefficient was determined by the dynamic oxygen absorption technique using a polarographic dissolved oxygen probe and the gas–liquid interfacial area was measured using dual‐tip conductivity probes in a bubble column slurry reactor at ambient temperature and normal pressure. The solid particles used were ultrafine hollow glass microspheres with a mean diameter of 8.624 µm. The effects of various axial locations (height–diameter ratio = 1–12), superficial gas velocity (u_G = 0.011–0.085 m/s) and solid concentration (ε_S = 0–30 wt.%) on the gas–liquid volumetric mass transfer coefficient k_La_L and liquid‐side mass transfer coefficient k_L were discussed in detail in the range of operating variables investigated. Empirical correlations by dimensional analysis were obtained and feed‐forward back propagation neural network models were employed to predict the gas–liquid volumetric mass transfer coefficient and liquid‐side mass transfer coefficient for an air–water–hollow glass microspheres system in a commercial‐scale bubble column slurry reactor. © 2012 Canadian Society for Chemical Engineering     

Comparison of Hydrodynamics and Mass Transfer in Airlift and Bubble Column Reactors Using CFD

Computational Fluid Dynamics (CFD) is used to compare the hydrodynamics and mass transfer of an internal airlift reactor with that of a bubble column reactor, operating with an air/water system in the homogeneous bubble flow regime. The liquid circulation velocities are significantly higher in the airlift configuration than in bubble columns, leading to significantly lower gas holdups. Within the riser of the airlift, the gas and liquid phases are virtually in plug flow, whereas in bubble columns the gas and liquid phases follow parabolic velocity distributions. When compared at the same superficial gas velocity, the volumetric mass transfer coefficient, k_La, for an airlift is significantly lower than that for a bubble column. However, when the results are compared at the same values of gas holdup, the values of k_La are practically identical.     

Interfacial Area and Liquid‐Side Volumetric Mass Transfer Coefficient in a Downflow Bubble Column

An experimental investigation was made to measure interfacial area, a, and liquid‐side volumetric mass transfer coefficient, k_La, in a downflow bubble column by chemical methods viz., absorbing CO₂ in aqueous sodium hydroxide and sodium carbonate/bicarbonate buffer solution respectively. The effect of gas and liquid flowrate and nozzle sizes on a and k_La were investigated. The experimental data obtained in the present system were analyzed and correlations were developed to predict a and k_La in terms of superficial gas velocity. The variation of a and k_La with specific power input were shown in graphical plot and compared with other gas‐liquid systems.     

Einfluss mikrostrukturierter statischer Mischer auf den Gas/Flüssig‐Stofftransport in einem engen Rechteckkanal

Experimental results of the volumetric mass transfer coefficient k_La_Ph in a microstructured rectangular channel (Miprowa®) with static mixers are presented. The physical absorption of CO₂ in H₂O was identified as suitable measuring method. The results include a gas‐liquid flow map and the identification of different flow regimes as well as first systematic measurements of the k_La_Ph value as a function of various process settings like gas and liquid flow rate and gas holdup. A first comparison of Miprowa® with established gas‐liquid contact devices like stirred tank and bubble column is given.     

Gas Holdup and Volumetric Mass Transfer Coefficient in a Slurry Bubble Column

The gas holdup, ?, and volumetric mass transfer coefficient, k_La, were measured in a 0.051 m diameter glass column with ethanol as the liquid phase and cobalt catalyst as the solid phase in concentrations of 1.0 and 3.8 vol.‐%. The superficial gas velocity U was varied in the range from 0 to 0.11 m/s, spanning both the homogeneous and heterogeneous flow regimes. Experimental results show that increasing catalyst concentration decreases the gas holdup to a significant extent. The volumetric mass transfer coefficient, k_La, closely follows the trend in gas holdup. Above a superficial gas velocity of 0.04 m/s the value of k_La/? was found to be practically independent of slurry concentration and the gas velocity U; the value of this parameter is found to be about 0.45 s^–1. Our studies provide a simple method for the estimation of k_La in industrial‐size bubble column slurry reactors.     

Experimental Study of Oxygen Mass Transfer Coefficient in Bubble Column with High Temperature and High Pressure

The volumetric gas‐liquid mass transfer coefficient, k_Lα, for oxygen was studied by using the dynamic method in slurry bubble column reactors with high temperature and high pressure. The effects of temperature, pressure, superficial gas velocity and solids concentration on the mass transfer coefficient are systemically discussed. Experimental results show that the gas‐liquid mass transfer coefficient increases with the increase in pressure, temperature, and superficial gas velocity, and decreases with the increase in solids concentration. Moreover, k_Lα values in a large bubble column are slightly higher than those in a small one at certain operating conditions. According to the analysis of experimental data, an empirical correlation is obtained to calculate the values of the oxygen volumetric mass transfer coefficient for a water‐quartz sand system in two bubble columns with different diameter at high temperature and high pressure.     

Gas‐Liquid Mass Transfer in Fibrous Bed Reactor with Counter‐Current Liquid Recycle

In this work, the gas‐liquid mass transfer in a lab‐scale fibrous bed reactor with liquid recycle was studied. The volumetric gas‐liquid mass transfer coefficient, k_La, is determined over a range of the superficial liquid velocity (0.0042–0.0126 m.s^–1), gas velocity (0.006–0.021 m.s^–1), surface tension (35–72 mN/m), and viscosity (1–6 mPa.s). Increasing fluid velocities and viscosity, and decreasing interfacial tension, the volumetric oxygen transfer coefficient increased. In contrast to the case of co‐current flow, the effect of gas superficial velocity was found to be more significant than the liquid superficial velocity. This behavior is explained by variation of the coalescing gas fraction and the reduction in bubble size. A correlation for k_La is proposed. The predicted values deviate within ± 15 % from the experimental values, thus, implying that the equation can be used to predict gas‐liquid mass transfer rates in fibrous bed recycle bioreactors.     

Hydrodynamics,Mass Transfer and Gas Scrubbing in a Co‐current Droplet Column Operating at High Gas Velocities

The main objective of this work was to propose a new process for household fume incineration treatment: the droplet column. A feature of this upward gas‐liquid reactor which makes it original, is to use high superficial gas velocities (13 m s^–1) which allow acid gas scrubbing at low energy costs. Tests were conducted to characterize the hydrodynamics, mass transfer performances, and acid gas scrubbing under various conditions of superficial gas velocity (from 10.0 to 12.0 m s^–1) and superficial liquid velocity (from 9.4·10^–3 to 18.9·10^–3 m s^–1). The following parameters characterized the hydrodynamics: pressure drops, liquid hold‐ups, and liquid residence time distribution were identified and investigated with respect to flow conditions. To characterize mass transfer in the droplet column, three parameters were determined: the gas‐liquid interfacial area (a), the liquid‐phase volumetric mass transfer coefficient (k_La) and the gas‐phase volumetric mass transfer coefficient (k_Ga). Gas absorption with chemical reaction methods were applied to evaluate a and k_Ga, while a physical absorption method was used to estimate k_La. The influence of the gas and liquid velocities on a, k_La, and k_Ga were investigated. Furthermore, tests were conducted to examine the utility of the droplet column for the acid gas scrubbing, of gases like hydrogen chloride (HCl) and sulfur dioxide (SO₂). This is a process of high efficiency and the amount of pollutants in the cleaned air is always much lower than the regulatory European standards imposed on household waste incinerators.     

Gas‐Liquid Mass Transfer in a Slurry Bubble Column at High Slurry Concentrations and High Gas Velocities

The volumetric mass transfer coefficient k_La in a 0.1 m‐diameter bubble column was studied for an air‐slurry system. A C₉‐C₁₁ n‐paraffin oil was employed as the liquid phase with fine alumina catalyst carrier particles used as the solid phase. The n‐paraffin oil had properties similar to those of the liquid phase in a commercial Fischer‐Tropsch reactor under reaction conditions. The superficial gas velocity U_G was varied in the range of 0.01 to 0.8 m/s, spanning both the homogeneous and heterogeneous flow regimes. The slurry concentration ?_S ranged from 0 to 0.5. The experimental results obtained show that the gas hold‐up ?_G decreases with an increase in slurry concentration, with this decrease being most significant when ?_S < 0.2. k_La/?_G was found to be practically independent of the superficial gas velocity when U_G > 0.1 m/s is taking on values predominantly between 0.4 and 0.6 s^–1 when ?_S = 0.1 to 0.4, and 0.29 s^–1, when ?_S = 0.5. This study provides a practical means for estimating the volumetric mass transfer coefficient k_La in an industrial‐size bubble column slurry reactor, with a particular focus on the Fischer‐Tropsch process as well as high gas velocities and high slurry concentrations.     

Gas‐Liquid Mass Transfer in Pulp Retention Towers

The volumetric gas‐liquid mass transfer rate, k_La, was measured under batch conditions in a 0.28 m diameter laboratory‐scale retention column. Tests on water, and on unbleached kraft (UBK) pulp suspensions (mass fractions, C_m from 0.013 to 0.09) were made with air or nitrogen sparged through the column at superficial gas velocities between 0.0015 to 0.05 m/s. k_La varied with suspension mass concentration and superficial gas velocity, initially decreasing with increasing mass concentration, reaching a minimum between C_m = 0.03 and 0.06, and then increasing. The minimum in k_La coincided with a change in hydrodynamics within the column, from bubble column behaviour below C_m = 0.03 to porous solid behaviour above C_m = 0.06.     

Bubble shape,gas flow and gas–liquid mass transfer in pulp fibre suspensions

Gas–liquid mass transfer in pulp fibre suspensions in a batch‐operated bubble column is explained by observations of bubble size and shape made in a 2D column. Two pulp fibre suspensions (hardwood and softwood kraft) were studied over a range of suspension mass concentrations and gas flow rates. For a given gas flow rate, bubble size was found to increase as suspension concentration increased, moving from smaller spherical/elliptical bubbles to larger spherical‐capped/dimpled‐elliptical bubbles. At relatively low mass concentrations (C_m = 2–3% for the softwood and C_m ? 7% for the hardwood pulp) distinct bubbles were no longer observed in the suspension. Instead, a network of channels formed through which gas flowed. In the bubble column, the volumetric gas–liquid mass transfer rate, k_La, decreased with increasing suspension concentration. From the 2D studies, this occurred as bubble size and rise velocity increased, which would decrease overall bubble surface area and gas holdup in the column. A minimum in k_La occurred between C_m = 2% and 4% which depended on pulp type and was reached near the mass concentration where the flow channels first formed.     

Efficiency of a Gas‐Liquid Contactor for the Oxygenation of Activated Sludge: Assessment of Mass Transfer Coefficient

The aim of this work is to investigate a co‐current air‐liquid downward flow bubble column with air entrainment by liquid injection nozzle in order to use it as an aerator in activated sludge treatment plants. The study concerns the determination of mass transfer efficiency by measuring the mass transfer coefficient, k_La, both in clean water and in activated sludge. In clean water, this parameter is determined by three methods, i.e., gassing out method, absorption with chemical reaction and off‐gas method. In activated sludge medium, k_La values are measured by two methods, i.e., sludge reoxygenation and the hydrogen‐peroxide method. The values of k_La obtained in clean water are compared to those obtained in sludge, enabling the assessment of the α factor, i.e., ratio of oxygen transfer coefficient sludge/clean water. The results are in good agreement with those reported previously in the literature.     

Using image analysis in the study of multiphase gas absorption

For the air-water-calcium alginate beads system, the effect of the presence of solids on the mass transfer characteristics in a bubble column was experimentally studied.Volumetric liquid side mass transfer coefficient, k_La, specific interfacial area, a, and hence liquid side mass transfer coefficient, k_L, were determined under different solid concentrations (0, 5, and 10 vol%), superficial gas velocities (up to 0.27 cm/s) and solid sizes (1.2 and 2.1 mm diameter). The bubble characteristics, namely the interfacial area, were obtained using an image analysis technique.This technique proved to be a suitable and practical method to characterize mass transfer phenomena in bubble columns for the range of operating conditions used. The solids affect negatively k_La, decreasing both a and k_L, the effect being more pronounced for the smaller particles. For these particles the variation of k_La is due to the variation of its two components, while for larger particles k_La variation is due, essentially, to changes in k_L as no significant differences in a were observed.     

HYDRODYNAMICS AND MASS TRANSFER IN DOWNFLOW BUBBLE COLUMN

Gas holdup, effective interfacial area and volumetric mass transfer coefficient were measured in two and three phase downflow bubble columns. The mass transfer data were obtained using the chemical method of sulfite oxidation, and the gas holdup was measured using the hydrostatic technique. Glass beads and Triton 114 were used to study the effects of solids and liquid surface tension on the gas holdup and the mass transfer parameters a and k_L a . The gas holdup in three phase systems was measured for non-wettable (glass bead) and wettable (coal and shale particles) solids.

The mass transfer data obtained in the downflow bubble column were compared with the values published for upflow bubble columns. The results indicate that in the range of superficial gas velocities (0.002-0.025) m/s investigated, the values of the mass transfer coefficient were of the same order of magnitude as those observed in upflow systems, but the values of interfacial area were at least two fold greater. Also, the results showed that the operating variables and the physical properties had different influences on a and k_L a in the downflow bubble column. Correlations for a and k_L a for the downflow bubble column are proposed which predict the data with adequate accuracy in the range of operating conditions investigated.     

HYDRODYNAMIC CHARACTERISTICS AND GAS-LIQUID MASS TRANSFER IN A DRAFT TUBE SLURRY REACTOR

Fundamental characteristics of hydrodynamics and mass transfer have been measured in an air lift slurry reactor with a draft tube. The solid suspension capacity, i.e., the critical solid holdup, the gas holdup and the volumetric gas-liquid mass transfer coefficient were measured in the two draft tube columns of 0.1485 and 0.10?m in diameter. Four activated carbon beads ranging in size from 0.25 to 2.19?mm in average diameter were utilized as suspended solids in the experiments.

The critical solid holdup in the draft tube slurry column is found to be much greater than that in the conventional bubble column. An empirical correlation is developed to account for the critical solid holdup behavior in the draft tube column. The gas holdup in the draft tube column agrees well with that in the bubble column. The overall gas-liquid mass transfer coefficient, k₁awas measured by the oxygen probe method. The effect of solid holdup on k₁a is found to be negligible in the present system. The empirical equation is developed to correlate k₁a in the draft tube slurry reactor.     

Bubble size and mass transfer coefficients in dual-impeller agitated reactors

The study relates to the mass transfer and the bubble size in a non standard vessel equipped with various dual-impeller combinations. The effects of the rotational speed, gas flow rate, impeller type and diameter are investigated. The volumetric mass transfer coefficient k_La and the bubble size d_bs were studied. The liquid side mass transfer coefficient k_L and the volumetric interfacial area a were estimated separately. A comparison has been made with some existing correlations.     

Gas–liquid interfacial area and mass transfer coefficient in a co‐current down flow contacting column

The gas–liquid interfacial area and mass transfer coefficient for absorption of oxygen from air into water, aqueous glycerol solutions up to 1.5% (w/w) and fermentation medium containing glucose up to a 3% concentration were determined in a co‐current down flow contacting column (CDCC; 0.05 m i.d. and 0.8 m length). Experimental studies were conducted using various nozzle diameters at different gas and re‐circulation liquid rates. Specific interfacial area (a) is determined from the fractional gas hold‐up (ε_G) and the average bubble diameter (d_b). Once the interfacial area is determined, the volumetric mass transfer coefficient (k_La) is then used to evaluate the film mass transfer coefficient in the CDCC. The effects of operating conditions and liquid properties on the specific interfacial area were investigated. The values of interfacial area in air–aqueous glycerol solutions and fermentation media were found to be lower than those in the air–water system. As far as experimental conditions were concerned, the values of interfacial area obtained from this study were found to be considerably higher than those of the literature values of conventional bubble columns. The penetration theory is used to interpret the film mass transfer coefficient and results match the experimental k_L data reasonably well. Copyright © 2006 Society of Chemical Industry     

Influence of Pressure on the Hydrodynamics and Mass Transfer Parameters of an Agitated Bubble Reactor

The present study deals with the pressure effects on the hydrodynamic flow and mass transfer within an agitated bubble reactor operated at pressures between 10⁵ and 100 × 10⁵ Pa. In order to clarify the flow behavior within the reactor, liquid phase residence time distributions (RTD) for different operating pressures and gas velocities ranging between 0.005 m/s and 0.03 m/s are determined experimentally by the tracer method for which a KCl solution is used as a tracer. The result of the analysis of the liquid‐phase RTD curves justifies the tank‐in‐series model flow for the operating pressure range. Good agreement is obtained between theoretical and experimental results assuming the reactor is operating as perfectly mixed. Two parameters characterizing the mass transfer are identified and investigated in respect to pressure: the gas‐liquid interfacial area and volumetric liquid‐side mass transfer coefficient. The chemical absorption method is used. For a given gas mass flow rate, the interfacial area as well as the volumetric liquid mass transfer coefficient decrease with increasing operating pressure. However, for a given pressure, a and k_La increase with increasing gas mass flow rates. The mass transfer coefficient k_L is independent of pressure.     

Gas holdup,bubble size distribution,and mass transfer in an airlift reactor with ceramic membrane and perforated plate distributor

The airlift reactor is one of the most commonly used gas–liquid two-phase reactors in chemical and biological processes. The objective of this study is to generate different-sized bubbles in an internal loop airlift reactor and characterize the behaviours of the bubbly flows. The bubble size, gas holdup, liquid circulation velocity, and the volumetric mass transfer coefficient of gas–liquid two-phase co-current flow in an internal loop airlift reactor equipped with a ceramic membrane module (CMM) and a perforated-plate distributor (PPD) are measured. Experimental results show that CMM can generate small bubbles with Sauter mean diameter d₃₂ less than 2.5 mm. As the liquid inlet velocity increases, the bubble size decreases and the gas holdup increases. In contrast, PPD can generate large bubbles with 4 mm < d₃₂ < 10 mm. The bubble size and liquid circulation velocity increase as the superficial gas velocity increases. Multiscale bubbles with 0.5 mm < d₃₂ < 10 mm can be generated by the CMM and PPD together. The volumetric mass transfer coefficient k_La of the multiscale bubbles is 0.033–0.062 s⁻¹, while that of small bubbles is 0.011–0.057 s⁻¹. Under the same flow rate of oxygen, the k_La of the multiscale bubbles increases by up to 160% in comparison to that of the small bubbles. Finally, empirical correlations for k_La are obtained.     

Bubble column research in Japan

Many experimental studies on the bubble column have been reported by Japanese researchers since around 1960. They include studies of bubble behaviour, bubble size distribution, transition from the homogeneous bubbly flow regime to the heterogeneous liquid circulation regime, liquid velocity distribution, longitudinal liquid mixing, hydrodynamic modelling, the gas holdup, and the volumetric coefficient of gas-liquid mass tranfer k_La. Studies covered various modified bubble columns, such as the airlift reactor with an external or internal loop, the packed bubble column, and others. Performance of three-phase bubble columns, which deal with suspensions or emulsions, and their use as bioreactors or chemical reactors were also studied.