A single-chip digitally calibrated 5.15-5.825-GHz 0.18-/spl mu/m CMOS transceiver for 802.11a wireless LAN

The drive for cost reduction has led to the use of CMOS technology in the implementation of highly integrated radios. This paper presents a single-chip 5-GHz fully integrated direct conversion transceiver for IEEE 802.11a WLAN systems, manufactured in 0.18-/spl mu/m CMOS. The IC features an innovative system architecture which takes advantage of the computing resources of the digital companion chip in order to eliminate I/Q mismatch and achieve accurately matched baseband filters. The integrated voltage-controlled oscillator and synthesizer achieve an integrated phase noise of less than 0.8/spl deg/ rms. The receiver has an overall noise figure of 5.2 dB and achieves sensitivity of -75 dBm at 54-Mb/s operation, both referred to the IC input. The transmit error vector magnitude is -33 dB at -5-dBm output power from the integrated power-amplifier driver amplifier. The transceiver occupies an area of 18.5 mm/sup 2/.     

A 75-dB image rejection IF-input quadrature-sampling SC /spl Sigma//spl Delta/ Modulator

Quadrature sampling of intermediate frequency (IF) signals is subject to the well-known problem of gain and phase mismatches between the in-phase (I) and quadrature (Q) channels. This paper presents an IF-input quadrature-sampling switched-capacitor (SC) /spl Sigma//spl Delta/ modulator that circumvents the I/Q mismatch problem by time-sharing between the I and Q channels the critical circuit components, namely, the sampling capacitor and the capacitor of the first-stage feedback digital-to-analog converter (DAC). In addition, a clocking scheme that is insensitive to I/Q phase imbalance is used. A third-order single-loop 1-bit low-pass modulator has been designed and fabricated in a 0.35-/spl mu/m CMOS process with an active area of 0.57mm/sup 2/. The experimental results show that the modulator achieves an image-rejection ratio (IRR) of greater than 75dB throughout a 200-kHz signal bandwidth.     

I/Q mismatch compensation using adaptive decorrelation in a low-IF receiver in 90-nm CMOS process

We present a single multiplier based adaptive I/Q mismatch compensation circuit for narrowband quadrature receivers. Adaptive decorrelation between I and Q channel data is used for correcting gain and phase mismatches. Adaptation step size is computed from L/sub 1/-norm inverse power measurement and a gear-shifting mechanism is used that allows fast initial convergence and slow adaptation on actual burst data. Image rejection ratio in excess of 50 dB is reported for GSM receiver after compensation allowing the receiver to use IF frequencies higher than half of the channel bandwidth. The presented mismatch compensation circuit is implemented as part of a single-chip GSM wireless transceiver fabricated in a 90-nm digital CMOS process. The presented techniques are, however, equally applicable to other narrowband packet-based applications.     

A UWB CMOS transceiver

A direct-conversion ultra-wideband (UWB) transceiver for Mode 1 OFDM applications employs three resonant networks and three phase-locked loops. Using a common-gate input stage, the receiver allows direct sharing of the antenna with the transmitter. Designed in 0.13-/spl mu/m CMOS technology, the transceiver provides a total gain of 69-73 dB and a noise figure of 6.5-8.4 dB across three bands, and a TX 1-dB compression point of -10 dBm. The circuit consumes 105 mW from a 1.5-V supply.     

A CMOS TV tuner/demodulator IC with digital image rejection

Superheterodyne TV tuners have been implemented in discrete forms using tunable RF and SAW IF filters. Integrating TV tuners in CMOS technology without them is a challenging task to cope with technical issues such as harmonic mixing and image. The image rejection in low- or zero-IF systems has been limited to 30-40 dB by analog imperfections such as I/Q path gain and phase mismatches. A single-chip low-IF TV tuner solution is proposed so that the image can be suppressed digitally using an image cancellation technique based on a complex one-tap LMS signal decorrelation algorithm. Programmable digital filtering and video/sound demodulation make a multistandard TV tuner feasible in the 48-860 MHz VHF/UHF band. The chip has a maximum gain of 63 dB and an input automatic gain control (AGC) range from -15 to 25 dB with 0.85-dB steps. It achieves an image and IF rejection of 60 dB, a peak carrier-to-noise ratio (CNR) of 55 dB, and a peak sound signal-to-noise ratio (SNR) of 44 dB without frequency modulation (FM) de-emphasis. The prototype occupies 6/spl times/6 mm/sup 2/ in 0.25-/spl mu/m CMOS and consumes 1 W at 2.5 V.     

Subharmonically pumped CMOS frequency conversion (up and down) circuits for 2-GHz WCDMA direct-conversion transceiver

Subharmonically pumped frequency down- and upconversion circuits are implemented in 0.18-/spl mu/m mixed-mode CMOS technology for 2-GHz direct-conversion WCDMA transceiver applications. These circuits operate in quadrature double-balanced mode and a required octet-phases (0/spl deg/, 45/spl deg/, 90/spl deg/, 135/spl deg/, 180/spl deg/, 225/spl deg/, 270/spl deg/, and 315/spl deg/) local oscillator (LO) signal comes from an active multiphases LO generator composed of a polyphase filter and active 45/spl deg/ phase shifting circuits. For linearity improvement, predistortion compensation and negative feedback schemes are used in the frequency down- and upconversion circuits, respectively. The downconverter achieves a conversion voltage gain of 20 dB (to 1-M/spl Omega/ load), 4-dBm IIP3 (18-dBm OIP3 to 50-/spl Omega/ load), 41-dBm IIP2 and 8.5-dB DSB NF at 1-MHz IF frequency, consuming 13.4 mA from 1.8-V supply, in the WCDMA Rx band (2110-2170 MHz). The upconverter, operating as two switched gain modes in the WCDMA Tx band (1920-1980 MHz), consumes 19.4 mA from 1.8-V supply and shows 14.5-dB conversion power gain, 15 -dBm OIP3 (0.5-dBm IIP3) and -11 dBm P/sub 1dB/ at maximum gain mode. At minimum gain mode, it realizes -0.3-dB conversion loss, 10.7-dBm OIP3 (11-dBm IIP3) and 0-dBm P/sub 1dB/, respectively. 3GPP WCDMA modulation tests are performed for both up- and downconversion circuits and the results are discussed in this paper.     

A CMOS oversampling bandpass cascaded D/A converter with digital FIR and current-mode semi-digital filtering

An oversampling bandpass digital-to-analog converter has been designed so as to eliminate the carrier leak and in-band SNR degradation that accompany I and Q channel mismatch in wireless transmitters. The converter combines a cascaded noise-shaping sigma-delta (/spl Sigma//spl Delta/) modulator with digital finite impulse response (FIR) and mixed-signal semi-digital filters that attenuate out-of-band quantization noise. The performance of the converter in the presence of current source mismatch has been improved through the use of bandpass data weighted averaging. An experimental prototype of the converter, integrated in a 0.25-/spl mu/m CMOS technology, provides 83 dB of dynamic range for a 6.25-MHz signal band centered at 50 MHz, and suppresses out-of-band quantization noise by 38 dB.     

Development of multiband phase shifters in 180-nm RF CMOS technology with active loss compensation

We present the design and development of a novel integrated multiband phase shifter that has an embedded distributed amplifier for loss compensation in 0.18-/spl mu/m RF CMOS technology. The phase shifter achieves a measured 180/spl deg/ phase tuning range in a 2.4-GHz band and a measured 360/spl deg/ phase tuning range in both 3.5- and 5.8-GHz bands. The gain in the 2.4-GHz band varies from 0.14 to 6.6 dB during phase tuning. The insertion loss varies from -3.7 dB to 5.4-dB gain and -4.5 dB to 2.1-dB gain in the 3.5- and 5.8-GHz bands, respectively. The gain variation can be calibrated by adaptively tuning the bias condition of the embedded amplifier to yield a flat gain during phase tuning. The return loss is less than -10 dB at all conditions. The chip size is 1200 /spl mu/m/spl times/2300 /spl mu/m including pads.     

RF I/Q Downconverter With Gain/Phase Calibration

We propose an RF I/Q downconverter including a calibration procedure to compensate for gain and phase mismatch errors. The indirect compensation technique is based on the use of the local oscillator (LO) signal as reference for error measurements. A number of mismatch parameters are first estimated by an algorithm running in the digital signal processing processor following the analog-to-digital converter and then used to correct the downconverted I/Q signals digitally during normal operation. The downconverter has been designed in 0.13-mum CMOS technology. The analog part of the system for calibration adds a negligible area and power consumption with respect to the front-end building blocks. Test results exhibit an image-rejection ratio IRRges48.8 dB for I/Q phase errors up to 15deg and for LO I/Q amplitude and mixer gain mismatch errors up to 10%     

A monolithic 3.1-4.8 GHz MB-OFDM UWB transceiver in 0.18-μm CMOS

A monolithic RF transceiver for an MB-OFDM UWB system in 3.1-4.8 GHz is presented.The transceiver adopts direct-conversion architecture and integrates all building blocks including a gain controllable wideband LNA,a I/Q merged quadrature mixer,a fifth-order Gm-C bi-quad Chebyshev LPF/VGA,a fast-settling frequency synthesizer with a poly-phase filter,a linear broadband up-conversion quadrature modulator,an active D2S converter and a variablegain power amplifier.The ESD protected transceiver is fabricated in Jazz Semiconductor's 0.18-μm RF CMOS with an area of 6.1 mm2 and draws a total current of 221 mA from 1.8-V supply.The receiver achieves a maximum voltage gain of 68 dB with a control range of 42 dB in 6 dB/Step,noise figures of 5.5-8.8 dB for three sub-bands,and an inband/out-band IIP3 better than-4 dBm/+9 dBm.The transmitter achieves an output power ranging from-10.7 to-3dBm with gain control,an output P1dB better than-7.7 dBm,a sideband rejection about 32.4 dBc,and LO suppression of 31.1 dBc.The hopping time among sub-bands is less than 2.05 ns.     

A CMOS VGA With DC Offset Cancellation for Direct-Conversion Receivers

A CMOS dB-linear variable gain amplifier (VGA) with a novel I/Q tuning loop for dc-offset cancellation is presented. The CMOS dB-linear VGA provides a variable gain of 60 dB while maintaining its 3-dB bandwidth greater than 2.5 MHz. A novel exponential circuit is proposed to obtain the dB-linear gain control characteristics. Nonideal effects on dB linearity are analyzed and the methods for improvement are suggested. A varying-bandwidth LPF is employed to achieve fast settling. The chip is fabricated in a 0.35- $mu{hbox {m}}$ CMOS technology and the measurement results demonstrate the good dB linearity of the proposed VGA and show that the tuning loop can effectively remove dc offset and suppress I/Q mismatch effects simultaneously.      

A 5.7-GHz 0.18-/spl mu/m CMOS gain-controlled differential LNA with current reuse for WLAN receiver

This letter presents a 5.7 GHz 0.18 /spl mu/m CMOS gain-controlled differential LNA for an IEEE 802.11a WLAN application. The differential LNA, fabricated with the 0.18 /spl mu/m 1P6M standard CMOS process, uses a current-reuse technology to increase linear gain and save power consumption. The circuit measurement is performed using an FR-4 PCB test fixture. The LNA exhibits a noise figure of 3.7 dB, linear gain of 12.5 dB, P/sub 1dB/ of -11 dBm, and gain tuning range of 6.9 dB. The power consumption is 14.4 mW at V/sub DD/=1.8 V.     

A single-chip CMOS transceiver for 802.11a/b/g wireless LANs

A dual-band trimode radio fully compliant with the IEEE 802.11a, b, and g standards is implemented in a 0.18-/spl mu/m CMOS process and packaged in a 48-pin QFN package. The transceiver achieves a receiver noise figure of 4.9/5.6 dB for the 2.4-GHz/5-GHz bands, respectively, and a transmit error vector magnitude (EVM) of 2.5% for both bands. The transmit output power is digitally controlled, allowing per-packet power control as required by the forthcoming 802.11 h standard. A quadrature accuracy of 0.3/spl deg/ in phase and 0.05 dB in amplitude is achieved through careful analysis and design of the I/Q generation parts of the local oscillator. The local oscillators achieve a total integrated phase noise of better than -34 dBc. Compatibility with multiple baseband chips is ensured by flexible interfaces toward the A/D and D/A converters, as well as a calibration scheme not requiring any baseband support. The chip passes /spl plusmn/2 kV human body model ESD testing on all pins, including the RF pins. The total die area is 12 mm/sup 2/. The power consumption is 207 mW in the receive mode and 247 mW in the transmit mode using a 1.8-V supply.     

A CMOS gyrator low-IF filter for a dual-mode Bluetooth/ZigBee transceiver

A low-IF polyphase channel filter for a dual-mode Bluetooth/Zigbee transceiver is described. Implemented in a standard 0.18-/spl mu/m CMOS process, the filter has a fifth-order 0.5-dB equiripple bandpass response and employs novel transconductor and preamplifier designs. It consumes /spl les/1 mW and achieves image band rejection /spl ges/44 dB, input referred noise of /spl les/52.2 /spl mu/Vrms and input referred third-order intermodulation intercept of /spl ges/20 dBVp, which gives a spurious-free dynamic range of /spl ges/68.4 dB. Chip area including its tuning circuit is 0.23 mm/sup 2/.     

A 3.1 GHz–8.0 GHz Single-Chip Transceiver for MB-OFDM UWB in 0.18-$mu$ m CMOS Process

This paper presents the design and integration of a fully-integrated dual-conversion zero-IF2 CMOS transceiver for 9-band MB-OFDM UWB systems from 3.1 GHz to 8.0 GHz. The transceiver integrates all building blocks including a variable-gain wideband LNA, a single combined mixer for both RF down-conversion in RX and up-conversion in TX, a fast-settling frequency synthesizer, and IQ ADCs and DACs. Fabricated in a standard 0.18- mum CMOS process, the receiver measures maximum S11 of - 13 dB, maximum NF of 8.25 dB, in-band IIP3 of better than -13.7 dBm, and variable gain from 25.3 to 84.0 dB. IQ path gain and phase mismatches of the receiver chain are measured to be 0.8 dB and 4 ^deg, respectively. The transmitter achieves a minimum output P-1 dB of -8.2 dBm, sideband rejection of better than -42.2 dBc, and LO leakage of smaller than - 46.5 dBc.     

A 3.3-mW /spl Sigma//spl Delta/ modulator for UMTS in 0.18-/spl mu/m CMOS with 70-dB dynamic range in 2-MHz bandwidth

A quadrature fourth-order, continuous-time, /spl Sigma//spl Delta/ modulator with 1.5-b quantizer and feedback digital-to-analog converter (DAC) for a universal mobile telecommunication system (UMTS) receiver chain is presented. It achieves a dynamic range of 70 dB in a 2-MHz bandwidth and the total harmonic distortion is -74 dB at full-scale input. When used in an integrated receiver for UMTS, the dynamic range of the modulator substantially reduces the need for analog automatic gain control and its tolerance of large out-of-band interference also permits the use of only first-order prefiltering. An IC including an I and Q /spl Sigma//spl Delta/ modulator, phase-locked loop, oscillator, and bandgap dissipates 11.5 mW at 1.8 V. The active area is 0.41 mm/sup 2/ in a 0.18-/spl mu/m 1-poly 5-metal CMOS technology.     

A dual-band 5.15-5.35-GHz, 2.4-2.5-GHz 0.18-/spl mu/m CMOS transceiver for 802.11a/b/g wireless LAN

A single-chip dual-band 5.15-5.35-GHz and 2.4-2.5-GHz zero-IF transceiver for IEEE 802.11a/b/g WLAN systems is fabricated on a 0.18-/spl mu/m CMOS technology. It utilizes an innovative architecture including feedback paths that enable digital calibration to help eliminate analog circuit imperfections such as transmit and receive I/Q mismatch. The dual-band receive paths feature a 4.8-dB (3.5-dB) noise figure at 5.25 GHz (2.45 GHz). The corresponding sensitivity at 54 Mb/s operation is -76 dBm for 802.11a and -77 dBm for 802.11g, both referred at the input of the chip. The transmit chain achieves output 1-dB compression at 6 dBm (9 dBm) at 5 GHz (2.4 GHz) operation. Digital calibration helps achieve an error vector magnitude (EVM) of -33 dB (-31 dB) at 5 GHz (2.4 GHz) while transmitting -4 dBm at 54Mb/s. The die size is 19.3 mm/sup 2/ and the power consumption is 260 mW for the receiver and 320 mW (270 mW) for the transmitter at 5 GHz (2.4 GHz) operation.     

A 4 GHz quadrature output fractional-N frequency synthesizer for an IR-UWB transceiver

This paper describes a 4 GHz fractional-N frequency synthesizer for a 3.1 to 5 GHz IR-UWB transceiver.Designed in a 0.18μm mixed-signal & RF 1P6M CMOS process, the operating range of the synthesizer is 3.74 to 4.44 GHz. By using an 18-bit third-order ∑-△ modulator, the synthesizer achieves a frequency resolution of 15 Hz when the reference frequency is 20 MHz. The measured amplitude mismatch and phase error between I and Q signals are less than 0.1 dB and 0.8° respectively. The measured phase noise is -116 dBc/Hz at 3 MHz offset for a 4 GHz output.Measured spurious tones are lower than -60 dBc. The settling time is within 80 μs. The core circuit conupSigmaes only 38.2 mW from a 1.8 V power supply.     

Low-voltage wideband compact CMOS variable gain amplifier

A novel low-voltage wideband CMOS variable gain amplifier (VGA) is proposed. Using a 0.13 /spl mu/m CMOS technology, the VGA exhibits a linear-dB controllable gain range of 40 dB with a bandwidth in excess of 130 MHz, while drawing only 50 /spl mu/A from a single 1 V power supply voltage.     

On the feasibility of CMOS multiband phase shifters for multiple-antenna transmitters

We present the design of an integrated multiband phase shifter in RF CMOS technology for phased array transmitters. The phase shifter has an embedded classical distributed amplifier for loss compensation. The phase shifter achieves a more than 180/spl deg/ phase tuning range in a 2.4-GHz band and a measured more than 360/spl deg/ phase tuning range in both 3.5-GHz and 5.8-GHz bands. The return loss is less than -10dB at all conditions. The feasibility for transmitter applications is verified through measurements. The output power at a 1-dB compression point (P/sub 1 dB/) is as high as 0.4dBmat 2.4GHz. The relative phase deviation around P/sub 1 dB/ is less than 3/spl deg/. The design is implemented in 0.18-/spl mu/mRF CMOS technology, and the chip size is 1200/spl mu/m /spl times/ 2300 /spl mu/m including pads.