Viscosity affected by nanoparticle aggregation in Al<Subscript>2</Subscript>O<Subscript>3</Subscript>-water nanofluids

An investigation on viscosity was conducted 2 weeks after the Al₂O₃-water nanofluids having dispersants were prepared at the volume concentration of 1-5%. The shear stress was observed with a non-Newtonian behavior. On further ultrasonic agitation treatment, the nanofluids resumed as a Newtonian fluids. The relative viscosity increases as the volume concentrations increases. At 5% volume concentration, an increment was about 60% in the re-ultrasonication nanofluids in comparison with the base fluid. The microstructure analysis indicates that a higher nanoparticle aggregation had been observed in the nanofluids before re-ultrasonication.     

Thermal conductivity and viscosity measurements of ethylene glycol-based Al<Subscript>2</Subscript>O<Subscript>3</Subscript> nanofluids

The dispersion and stability of nanofluids obtained by dispersing Al₂O₃ nanoparticles in ethylene glycol have been analyzed at several concentrations up to 25% in mass fraction. The thermal conductivity and viscosity were experimentally determined at temperatures ranging from 283.15 K to 323.15 K using an apparatus based on the hot-wire method and a rotational viscometer, respectively. It has been found that both thermal conductivity and viscosity increase with the concentration of nanoparticles, whereas when the temperature increases the viscosity diminishes and the thermal conductivity rises. Measured enhancements on thermal conductivity (up to 19%) compare well with literature values when available. New viscosity experimental data yield values more than twice larger than the base fluid. The influence of particle size on viscosity has been also studied, finding large differences that must be taken into account for any practical application. These experimental results were compared with some theoretical models, as those of Maxwell-Hamilton and Crosser for thermal conductivity and Krieger and Dougherty for viscosity.     

Preparation of stable magnetic nanofluids containing Fe<Subscript>3</Subscript>O<Subscript>4</Subscript>@PPy nanoparticles by a novel one-pot route

Stable magnetic nanofluids containing Fe₃O₄@Polypyrrole (PPy) nanoparticles (NPs) were prepared by using a facile and novel method, in which one-pot route was used. FeCl₃·6H₂O was applied as the iron source, and the oxidizing agent to produce PPy. Trisodium citrate (Na₃cit) was used as the reducing reagent to form Fe₃O₄ NPs. The as-prepared nanofluid can keep long-term stability. The Fe₃O₄@PPy NPs can still keep dispersing well after the nanofluid has been standing for 1 month and no sedimentation is found. The polymerization reaction of the pyrrole monomers took place with Fe³⁺ ions as the initiator, in which these Fe³⁺ ions remained in the solution adsorbed on the surface of the Fe₃O₄ NPs. Thus, the core-shell NPs of Fe₃O₄@PPy were obtained. The particle size of the as-prepared Fe₃O₄@PPy can be easily controlled from 7 to 30 nm by the polymerization reaction of the pyrrole monomers. The steric stabilization and weight of the NPs affect the stability of the nanofluids. The as-prepared Fe₃O₄@PPy NPs exhibit superparamagnetic behavior.     

Preparation and properties of poly(acrylic acid-co-styrene)/Fe<Subscript>3</Subscript>O<Subscript>4</Subscript> nanocomposites

Poly(acrylic acid-co-styrene)/Fe₃O₄ nanocomposites were prepared using poly(acrylic acid-co-styrene) (P(AA-co-St)) and nano-Fe₃O₄ particles. The resultant materials were characterized by transmission electron microscope (TEM), Fourier transform infrared (FTIR), thermogravimetric analysis (TGA), advanced rheology expand system and superconducting quantum interference device (SQUID) magnetometer. The diameter of the magnetic particles was around 3–14 nm. The experimental results reveal that the acrylic acid segment of P(AA-co-St) can react with nano-Fe₃O₄. With increasing reaction time the storage modulus, loss modulus, complex viscosity and shear stress of the P(AA-co-St)/Fe₃O₄ ethanol suspension were increased, and the suspension changed from liquid-like behavior to gel-like behavior for the reaction between P(AA-co-St) and Fe₃O₄, as found during the rheology measurements. The thermal stability of P(AA-co-St) decreased with the addition of nano-Fe₃O₄, and the nanocomposites exhibited superparamagnetic properties above the blocking temperature.     

Pool boiling of water-Al<Subscript>2</Subscript>O<Subscript>3</Subscript> and water-Cu nanofluids on horizontal smooth tubes

Experimental investigation of heat transfer during pool boiling of two nanofluids, i.e., water-Al₂O₃ and water-Cu has been carried out. Nanoparticles were tested at the concentration of 0.01%, 0.1%, and 1% by weight. The horizontal smooth copper and stainless steel tubes having 10 mm OD and 0.6 mm wall thickness formed test heater. The experiments have been performed to establish the influence of nanofluids concentration as well as tube surface material on heat transfer characteristics at atmospheric pressure. The results indicate that independent of concentration nanoparticle material (Al₂O₃ and Cu) has almost no influence on heat transfer coefficient while boiling of water-Al₂O₃ or water-Cu nanofluids on smooth copper tube. It seems that heater material did not affect the boiling heat transfer in 0.1 wt.% water-Cu nanofluid, nevertheless independent of concentration, distinctly higher heat transfer coefficient was recorded for stainless steel tube than for copper tube for the same heat flux density.     

Synthesis and thermal behavior of Fe<Subscript>3</Subscript>O<Subscript>2</Subscript>(BO<Subscript>4</Subscript>) oxoborate

Iron oxoborate Fe₃O₂(BO₄) has been first produced in solid-phase chemical reactions. Its thermal behavior in the temperature range 20–900°C is studied with the use in-situ high-temperature powder X-ray diffraction. It is shown that Fe₃O₂(BO₄) begins decomposing with the formation of Fe₂O₃ in the temperature range 660–900°C. Thermal expansion is sharply anisotropic at room temperature (α_max/α_min = 7) and becomes more isotropic with an increase in the temperature (α_max/α_min = 1.2). The degree of oxidation of Fe³⁺ has been confirmed by Mössbauer spectroscopy (at a room temperature), and two nonequivalent positions in the structure have been detected, which are occupied by iron atoms with the octahedral environment of the oxygen atoms.     

Effect of surface modification of Fe<Subscript>3</Subscript>O<Subscript>4</Subscript> nanoparticles on the preparation of Fe<Subscript>3</Subscript>O<Subscript>4</Subscript>/polystyrene composite particles via miniemulsion polymerization

Fe₃O₄ nanoparticles were modified by n-octadecyltrimethoxysilane (C18TMS) and 3-trimethoxysilylpropylmethacrylate (MPS). The modified Fe₃O₄ nanoparticles were used to prepare Fe₃O₄/polystyrene composite particles by miniemulsion polymerization. The effect of surface modification of Fe₃O₄ on the preparation of Fe₃O₄/polystyrene composite particles was investigated by transmission electron microscopy, Fourier transform infrared spectrophotometer (FT-IR), contact angle, and vibrating sample magnetometer (VSM). It was found that C18TMS modified Fe₃O₄ nanoparticles with high hydrophobic property lead to the negative effect on the preparation of the Fe₃O₄/polystyrene composite particles. The obtained composite particles exhibited asymmetric phase-separated structure and wide size distribution. Furthermore, un-encapsulated Fe₃O₄ were found in composite particles solution. MPS modified Fe₃O₄ nanoparticles showed poor hydrophobic properties and resulted in the obtained Fe₃O₄/polystyrene composite particles with regular morphology and narrow size distribution because the ended C=C of MPS on the surface of Fe₃O₄ nanoparticles could copolymerize with styrene which weakened the phase separation distinctly.     

Soft Template Synthesis of Super Paramagnetic Fe<Subscript>3</Subscript>O<Subscript>4</Subscript> Nanoparticles a Novel Technique

The present study reports a facile technique for the synthesis of crystalline super paramagnetic nano ferrite (Fe₃O₄) particles using diethyl amine as a soft template. The spectral properties of Fe₃O₄ nanoparticles were characterized by UV–visible and Fourier Transform Infrared (FTIR) spectroscopies while the crystalline structure and particle size was estimated using X-Ray diffraction (XRD) as well as transmission electron microscopy (TEM) techniques. The super paramagnetic behavior of Fe₃O₄ nanoparticles was determined using vibrating sample magnetometer (VSM) at 300 K. The results of the studies revealed that this technique could be adopted to synthesize agglomerate free super paramagnetic Fe₃O₄ nanoparticles which may find potential application in the filed of biosensor and corrosion protective coatings.     

Properties of a melt of the eutectic composition in the NaPO<Subscript>3</Subscript>-Na<Subscript>2</Subscript>B<Subscript>4</Subscript>O<Subscript>7</Subscript>-LiF system

Physical (density, viscosity) and thermophysical (heat capacity, thermal conductivity) properties of a melt of the eutectic composition (wt %) 84NaPO₃ · 8Na₂B₄O₇ · 8LiF have been investigated. It has been demonstrated that this eutectic mixture is a promising material for the use as a high-temperature heat-transfer agent.     

A study on synthesis and properties of Fe<Subscript>3</Subscript>O<Subscript>4</Subscript> nanoparticles by solvothermal method

Magnetic nanoparticles (Fe₃O₄) were synthesized by the solvothermal method using FeCl₃ · 6H₂O and ethylene glycol as a reactant. Powder X-ray diffraction, FT-IR, TEM, SEM, and VSM were used to characterize the magnetic particles. The reacting factors, such as reacting time, the concentration of iron source and surfactant, especially the effect of NaAc · 3H₂O, were studied. The results indicated that NaAc · 3H₂O plays the role not only as a dispersant but also a structure-directing agent. The synthesized Fe₃O₄ particles showed excellent magnetic property, which made them have potential for application in magnetic nanodevices and biomedicine.     

A Resumable Fluorescent Probe BHN-Fe<Subscript>3</Subscript>O<Subscript>4</Subscript>@SiO<Subscript>2</Subscript> Hybrid Nanostructure for Fe<Superscript>3+</Superscript> and its Application in Bioimaging

A multifunctional fluorescent probe BHN-Fe₃O₄@SiO₂ nanostructure for Fe³⁺ was designed and developed. It has a good selective response to Fe³⁺ with fluorescence quenching and can be recycled using an external magnetic field. With adding EDTA (2.5?×?10^?5 M) to the consequent product Fe³⁺-BHN-Fe₃O₄@SiO₂, Fe³⁺ can be removed from the complex, and its fluorescence probing ability recovers, which means that this constituted on-off type fluorescence probe could be reversed and reused. At the same time, the probe has been successfully applied for quantitatively detecting Fe³⁺ in a linear mode with a low limit of detection 1.25?×?10^?8 M. Furthermore, the BHN-Fe₃O₄@SiO₂ nanostructure probe is successfully used to detect Fe³⁺ in living HeLa cells, which shows its great potential in bioimaging detection.     

Evaluating the ability of separation and adsorption of SO<Subscript>2</Subscript> by nano-CuO-Fe<Subscript>2</Subscript>O<Subscript>3</Subscript>/TiO<Subscript>2</Subscript> in high concentrations and moderate temperatures

Nano CuO-Fe₂O₃/TiO₂ adsorbents were made with different compositions of metal oxides using precipitation- desorption method. The adsorbents were applied for adsorption of SO₂ at high concentrations ranging from 10,000 to 30,000 ppm and temperatures between 523 and 627 K. Adsorption experiments were applied for adsorbents in a laboratory fixed bed adsorption column. The adsorption capacity was measured by calculating the area under the adsorption curve using the integral method. The results showed that temperature is the most affecting factor on the adsorption capacity. The highest adsorption capacity was obtained by using 17, 8 and 75 wt% of CuO, Fe₂O₃ and nano TiO₂, respectively. Characteristics of the best sorbent were determined by using Fe-SEM, XRD and nitrogen adsorption-desorption analyses.     

Preparation and Characterization of Polyvinylpyrrolidone/ Magnetite Decorated Carboxylic Acid Functionalized Multi-walled Carbon Nanotube (PVP/MWCNT-Fe<Subscript>3</Subscript>O<Subscript>4</Subscript>) Nanocomposite

Magnetite decorated carboxylic acid functionalized multi-walled carbon nanotube (MWCNT-Fe₃O₄) was successfully inserted in polyvinylpyrrolidone (PVP) matrix in the aqueous media, as a result of which magnetic polymer nanocomposite (PVP/MWCNT-Fe₃O₄) was formed. With application of SEM, the surface morphology of the produced PVP/MWCNT-Fe₃O₄ nanocomposite was compared with that of pure PVP. The diameter distribution of Fe₃O₄ decorated carboxylic acid functionalized multi-walled carbon nanotube was determined by image analysis of the SEM micrographs. In addition, the structural and thermal characterizations of PVP/MWCNT-Fe₃O₄ nanocomposite were performed by FT-IR, XRD, TGA, and DSC techniques. Moreover, magnetic characterization of the prepared nanocomposite was determined by VSM. The obtained results indicated that addition of MWCNT-Fe₃O₄ (5% w/w) to PVP improved the thermal properties of pure polyvinylpyrrolidone. According to the results of DSC analysis, the glass transition temperature of 160?°C was observed for the PVP/MWCNT-Fe₃O₄ (5% w/w) nanocomposite. The FT-IR spectra showed that an interaction was taking place between MWCNT-Fe₃O₄ and PVP. The strong interaction with ~31 cm^?1 red shift along with good complexation of carbonyl functional group of PVP with MWCNT-Fe₃O₄ was observed for PVP/MWCNT-Fe₃O₄ (5% w/w) nanocomposite as a result of a better distribution of carbon nanotubes in the PVP matrix.     

Super-Thermite (Al/Fe<Subscript>2</Subscript>O<Subscript>3</Subscript>) Fluorocarbon Nanocomposite with Stimulated Infrared Thermal Signature via Extended Primary Combustion Zones for Effective Countermeasures of Infrared Seekers

Super-thermites can offer large amount of energy up to 16736 J/g. Flares based on super-thermites can offer superior thermal signature to countermeasure infrared (IR) guided missile seekers. This study reports on the sustainable fabrication of mono-dispersed Fe₂O₃ nanoparticles of 3 nm average particle size. Colloidal Fe₂O₃ nanoparticles were harvested from their synthesis medium and re-dispersed in acetone. Fluorocarbon polymers (teflon and viton) as well as aluminum metal fuel were integrated into Fe₂O₃/acetone colloid. The colloid mixture was granulated and mold pressed to develop the desired grain. The impact of Fe₂O₃ nanoparticles on thermal signature was assessed using (FT-MIR 1–6 µm) spectrometer. Flame propagation was investigated by video imaging of combustion wave. Combustion zones were quantified using image analysis. Quantification of flame temperature and main IR emitting species was performed using ICT thermodynamic code (virgin 2008). Nanocomposite flare with 12 wt% Fe₂O₃ offered an increase in the intensity of β band by 230% to that of reference formulation. The primary reaction zone was extended by 164%. Super-thermite particles not only offered superior spectral performance but also altered the combustion mechanism.     

Preparation and characterization of spindle-like Fe<Subscript>3</Subscript>O<Subscript>4</Subscript> mesoporous nanoparticles

Magnetic spindle-like Fe₃O₄ mesoporous nanoparticles with a length of 200 nm and diameter of 60 nm were successfully synthesized by reducing the spindle-like α-Fe₂O₃ NPs which were prepared by forced hydrolysis method. The obtained samples were characterized by transmission electron microscopy, powder X-ray diffraction, attenuated total reflection fourier transform infrared spectroscopy, field emission scanning electron microscopy, vibrating sample magnetometer, and nitrogen adsorption-desorption analysis techniques. The results show that α-Fe₂O₃ phase transformed into Fe₃O₄ phase after annealing in hydrogen atmosphere at 350°C. The as-prepared spindle-like Fe₃O₄ mesoporous NPs possess high Brunauer-Emmett-Teller (BET) surface area up to ca. 7.9 m² g^-1. In addition, the Fe₃O₄ NPs present higher saturation magnetization (85.2 emu g^-1) and excellent magnetic response behaviors, which have great potential applications in magnetic separation technology.     

Thermal behavior of layered perovskite-like compounds in the Bi<Subscript>4</Subscript>Ti<Subscript>3</Subscript>O<Subscript>12</Subscript>-BiFeO<Subscript>3</Subscript> system

The thermal properties of compounds of the general formula Bi _{m + 1} Fe _{m ? 3} Ti₃O_{3m + 3}, which are layered perovskite-like phases of the Aurivillius type, are investigated as a function of their composition. It is demonstrated that the temperature of decomposition of the Bi _{m + 1} Fe _{m ? 3} Ti₃O_{3m + 3} compounds decreases with an increase in the thickness of perovskite-like layers alternating in the structure and that the composition dependence of the temperature of the structural transition observed in these compounds exhibits a more complex behavior. The linear thermal expansion coefficients of all the compounds under investigation are found to be virtually independent of the composition.     

Phase Transformations in Stabilized ZrO<Subscript>2</Subscript> - Fe<Subscript>2</Subscript>O<Subscript>3</Subscript> Compositions

Data on interactions in the ZrO₂ - Fe₂O₃ system stabilized by oxides in a high-temperature form at 1750°C are obtained. Of all zirconia-based compositions, only magnesium-zirconium cubic solid solution enters into an active reaction with Fe₂O₃ to yield MgFe₂O₄. The solid solutions formed by ZrO₂ with oxides of yttrium, neodymium, and calcium resist degradation by attack from Fe₂O₃; part of iron oxide undergoes dissolution in cubic ZrO₂. __________ Translated from Novye Ogneupory, No. 9, pp. 40 – 43, September, 2005.     

Heterogeneous Fenton degradation of Orange II by immobilization of Fe<Subscript>3</Subscript>O<Subscript>4</Subscript> nanoparticles onto Al-Fe pillared bentonite

A novel catalyst, Fe₃O₄ nanoparticle decorated Al-Fe pillared bentonite (Fe₃O₄/Al-Fe-P-B), was prepared by in situ precipitation oxidization method. The catalyst was characterized by SEM, XRD and Raman spectroscopy. The Fe₃O₄ nanoparticles mainly exist on the surface or enter into the pore of bentonite, with better dispersing and less coaggregation. The catalytic activity of Fe₃O₄/Al-Fe-P-B was investigated in the degradation of Orange II (OII) by heterogeneous Fenton-like process. The effects of initial concentration of hydrogen peroxide, catalyst loading, temperature and initial pH on the degradation of OII were investigated. The Fe₃O₄/Al-Fe-P-B showed higher degradation efficiency of OII than bare Fe₃O₄ or Al-Fe-P-B in the degradation experiment. The enhanced catalytic activity of Fe₃O₄/Al-Fe-P-B in heterogeneous Fenton system was due to the synergistic effect between Al-Fe-P-B and Fe₃O₄. The novel catalyst can achieve solid-liquid separation easily by sample magnetic separation and has a good reusability and stability.     

Examining the use of Fe<Subscript>3</Subscript>O<Subscript>4</Subscript> nanoparticles to enhance the NH<Subscript>3</Subscript> sensitivity of polypyrrole films

Summary Polypyrrole (PPy) composite films with different contents of Fe₃O₄ were prepared by in-situ polymerization of pyrrole in aqueous solutions. The dependence of dc current changes on the response of the samples exposure to NH₃ vapor has been investigated. The results shows the composite films are more stable than the pristine ones after being exposed to NH₃ vapor. Meanwhile, the response time was reduced with increasing the Fe₃O₄ content in the films. The results might be originated from the structural changes in the PPy films caused by the addition of Fe₃O₄.     

Effect of HCl Concentration on the Dispersity of Fe<Subscript>3</Subscript>O<Subscript>4</Subscript> Nanoparticles

In this paper, monodisperse 6 nm-sized Fe₃O₄ nanoparticles with spinel crystalline structure were synthesized via a co-precipitation method. The effect of HCl concentrations on Fe₃O₄ samples was investigated by TEM, VSM and UV–vis. HCl-modified Fe₃O₄ nanoparticles solution was a stable, clear, transparent cationic colloid. The results showed that HCl had a great influence on the dispersity of Fe₃O₄ nanoparticles and almost no influence on the materials magnetism.