Characteristics of water transport through the membrane in direct methanol fuel cells operating with neat methanol

The water required for the methanol oxidation reaction in a direct methanol fuel cell (DMFC) operating with neat methanol can be supplied by diffusion from the cathode to the anode through the membrane. In this work, we present a method that allows the water transport rate through the membrane to be in-situ determined. With this method, the effects of the design parameters of the membrane electrode assembly (MEA) and operating conditions on the water transport through the membrane are investigated. The experimental data show that the water flux by diffusion from the cathode to the anode is higher than the opposite flow flux of water due to electro-osmotic drag (EOD) at a given current density, resulting in a net water transport from the cathode to the anode. The results also show that thinning the anode gas diffusion layer (GDL) and the membrane as well as thickening the cathode GDL can enhance the water transport flux from the cathode to the anode. However, a too thin anode GDL or a too thick cathode GDL will lower the cell performance due to the increases in the water concentration loss at the anode catalyst layer (CL) and the oxygen concentration loss at the cathode CL, respectively.     

Modeling of water transport through the membrane electrode assembly for direct methanol fuel cells

In this work, a one-dimensional, isothermal two-phase mass transport model is developed to investigate the water transport through the membrane electrode assembly (MEA) for liquid-feed direct methanol fuel cells (DMFCs). The liquid (methanol–water solution) and gas (carbon dioxide gas, methanol vapor and water vapor) two-phase mass transport in the porous anode and cathode is formulated based on classical multiphase flow theory in porous media. In the anode and cathode catalyst layers, the simultaneous three-phase (liquid and vapor in pores as well as dissolved phase in the electrolyte) water transport is considered and the phase exchange of water is modeled with finite-rate interfacial exchanges between different phases. This model enables quantification of the water flux corresponding to each of the three water transport mechanisms through the membrane for DMFCs, such as diffusion, electro-osmotic drag, and convection. Hence, with this model, the effects of MEA design parameters on water crossover and cell performance under various operating conditions can be numerically investigated.     

Effect of water concentration in the anode catalyst layer on the performance of direct methanol fuel cells operating with neat methanol

This paper reports on a chromatography-based method for determining the water concentration in the anode catalyst layer (CL) of a direct methanol fuel cell (DMFC). By this method, the effect of the water concentration in the anode CL on the product distribution of the methanol oxidation reaction (MOR), the anode potential, and the cell internal resistance is experimentally investigated in a DMFC operating with neat methanol. Interestingly, it is found that the main product of the anode MOR is still carbon dioxide even when the water concentration in the anode CL is extremely low. The experimental data also show that an increase in the water concentration in the anode CL decreases the internal resistance, the production of by-products (methyl formate and methylal), and the anode potential. As the mole ratio of water to methanol increases beyond a critical value, however, both the internal resistance and the anode potential tend to be stabilized at the points under diluted methanol operating conditions.     

Towards operating direct methanol fuel cells with highly concentrated fuel

A significant advantage of direct methanol fuel cells (DMFCs) is the high specific energy of the liquid fuel, making it particularly suitable for portable and mobile applications. Nevertheless, conventional DMFCs have to be operated with excessively diluted methanol solutions to limit methanol crossover and the detrimental consequences. Operation with diluted methanol solutions significantly reduces the specific energy of the power pack and thereby prevents it from competing with advanced batteries. In view of this fact, there exists a need to improve conventional DMFC system designs, including membrane electrode assemblies and the subsystems for supplying/removing reactants/products, so that both the cell performance and the specific energy can be simultaneously maximized. This article provides a comprehensive review of past efforts on the optimization of DMFC systems that operate with concentrated methanol. Based on the discussion of the key issues associated with transport of the reactants/products, the strategies to manage the supply/removal of the reactants/products in DMFC operating with highly concentrated methanol are identified. With these strategies, the possible approaches to achieving the goal of concentrated fuel operation are then proposed. Past efforts in the management of the reactants/products for implementing each of the approaches are also summarized and reviewed.     

Double microporous layer cathode for membrane electrode assembly of passive direct methanol fuel cells

A novel membrane electrode assembly (MEA) is described that utilizes a double microporous layer (MPL) structure in the cathode of a passive direct methanol fuel cell (DMFC). The double MPL cathode uses Ketjen Black carbon as an inner-MPL and Vulcan XC-72R carbon as an outer-MPL. Experimental results indicate that this double MPL structure at the cathode provides not only a higher oxygen transfer rate, but enables more effective back diffusion of water; thus, leading to an improved power density and stability of the passive DMFC. The maximum power density of an MEA with a double MPL cathode was observed to be ca. 33.0 mW cm⁻², which is found to be a substantial improvement over that for a passive DMFC with a conventional MEA. A. C. impedance analysis suggests that the increased performance of a DMFC with the double MPL cathode might be attributable to a decreased charge transfer resistance for the cathode oxygen reduction reaction.     

Basic model for membrane electrode assembly design for direct methanol fuel cells

This research proposes a model that predicts the effect of the anode diffusion layer and membrane properties on the electrochemical performance and methanol crossover of a direct methanol fuel cell (DMFC) membrane electrode assembly (MEA). It is an easily extensible, lumped DMFC model. Parameters used in this design model are experimentally obtainable, and some of the parameters are indicative of material characteristics. The quantification of these material parameters builds up a material database. Model parameters for various membranes and diffusion layers are determined by using various techniques such as polarization, mass balance, electrochemical impedance spectroscopy (EIS), and interpretation of the response of the cell to step changes in current. Since the investigation techniques cover different response times of the DMFC, processes in the cell such as transport, reaction and charge processes can be investigated separately. Properties of single layers of the MEA are systematically varied, and subsequent analysis enables identification of the influence of the layer's properties on the electrochemical performance and methanol crossover. Finally, a case study indicates that the use of a membrane with lower methanol diffusivity and a thicker anode micro-porous layer (MPL) yields MEAs with lower methanol crossover but similar power density.     

A prediction model of degradation rate for membrane electrode assemblies in direct methanol fuel cells

This article proposes a new prediction model to describe the nonlinear performance degradation paths of membrane electrode assemblies (MEAs) in direct methanol fuel cell (DMFC): a bi-exponential model with random coefficients. The bi-exponential model is constructed on a mathematical basis representing second-order kinetics. Performance variation between MEAs is incorporated by random coefficients in the proposed model. A likelihood ratio test is sequentially executed to select random effects in the nonlinear random-coefficients model. Analysis results indicate that the reliability estimation can be substantially improved by using the nonlinear random-coefficients model to incorporate two heterogeneous degradation characteristics of MEA performance during continuous operation of DMFC. Confidence intervals of failure-time distributions are obtained by the parametric bootstrap method.     

Effect of pressure for direct fuel cells using DME-based fuels

The performance of direct fuel cells using dimethyl ether(DME)-based fuels is presented at a relatively low temperature of 80 °C. DME is supplied to the fuel cells either by gas phase or aqueous phase for the operation of direct fuel cells. In order to keep DME in liquid phase during operation, fuel cells were operated at higher pressure up to 5 bar. For further increase of the power density from direct DME fuel cells, DME was mixed with methanol solution and fed into the fuel cells by the vapor pressure of DME itself without a liquid pump. In this study, we have obtained the highest power density of 210 mW cm⁻² at a temperature of 80 °C when the fuel cell is operated with the mixed fuel with 2 M methanol solution under 4 bar.     

An approach for determining the liquid water distribution in a liquid-feed direct methanol fuel cell

In determining the liquid water distribution in the anode (or the cathode) diffusion medium of a liquid-feed direct methanol fuel cell (DMFC) with a conventional two-phase mass transport model, a current-independent liquid saturation boundary condition at the interface between the anode flow channel and diffusion layer (DL) (or at the interface between the cathode flow channel and cathode DL) needs to be assumed. The numerical results resulting from such a boundary condition cannot realistically reveal the liquid distribution in the porous region, as the liquid saturation at the interface between the flow channel and DL varies with current density. In this work, we propose a simple theoretical approach that is combined with the in situ measured water-crossover flux in the DMFC to determine the liquid saturation in the anode catalyst layer (CL) and in the cathode CL. The determined liquid saturation in the anode CL (or in the cathode CL) can then be used as a known boundary condition to determine the water distribution in the anode DL (or in the cathode DL) with a two-phase mass transport model. The numerical results show that the water distribution becomes much more realistic than those predicted with the assumed boundary condition at the interface between the flow channel and DL.     

Lifetime prediction through accelerated degradation testing of membrane electrode assemblies in direct methanol fuel cells

To expand the applications of direct methanol fuel cells (DMFCs), the testing time required to evaluate their durability must be shortened. In this article, we present a step-by-step, accelerated degradation test (ADT) procedure for simple application by fuel cell engineers to the membrane electrode assembly (MEA) in DMFCs. Using MEA degradation data obtained under high stress conditions, we provide a method to estimate the lifetime distribution for normal use conditions and derive optimal testing plans for further degradation tests. A bi-exponential model with random coefficients is introduced to represent the nonlinear deterioration path of the MEAs. Based on the lifetimes estimated from the bi-exponential model at higher temperatures, the lifetime distribution at normal use temperature is extrapolated using the Weibull–Arrhenius model as the lifetime-temperature relationship.     

In situ measurements of water crossover through the membrane for direct methanol fuel cells

We show analytically that the water-crossover flux through the membrane used for direct methanol fuel cells (DMFCs) can be in situ determined by measuring the water flow rate at the exit of the cathode flow field. This measurement method enables investigating the effects of various design and geometric parameters as well as operating conditions, such as properties of cathode gas diffusion layer (GDL), membrane thickness, cell current density, cell temperature, methanol solution concentration, oxygen flow rate, etc., on water crossover through the membrane in situ in a DMFC. Water crossover through the membrane is generally due to electro-osmotic drag, diffusion and back convection. The experimental data showed that diffusion dominated the total water-crossover flux at low current densities due to the high water concentration difference across the membrane. With the increase in current density, the water flux by diffusion decreased, but the flux by back convection increased. The corresponding net water-transport coefficient was also found to decrease with current density. The experimental results also showed that the use of a hydrophobic cathode GDL with a hydrophobic MPL could substantially reduce water crossover through the membrane, and thereby significantly increasing the limiting current as the result of the improved oxygen transport. It was found that the cell operating temperature, oxygen flow rate and membrane thickness all had significant influences on water crossover, but the influence of methanol concentration was negligibly small.     

A theoretical model of the membrane electrode assembly of liquid feed direct methanol fuel cell with consideration of water and methanol crossover

An algebraic model of the membrane electrode assembly of the direct methanol fuel cell is developed, which considers the simultaneous liquid water and methanol crossover effects, and the associated electrochemical reactions. The respective anodic and cathodic polarization curves can be predicted using this model. Methanol concentration profile and flux are correlated explicitly with the operating conditions and water transport rate. The cathode mixed potential effect induced by the methanol crossover is included and the subsequent cell voltage loss is identified. Water crossover is influenced by the capillary pressure equilibrium and hydrophobic property within the cathode gas diffusion layer. The model can be used to evaluate the cell performance at various working parameters such as membrane thickness, methanol feed concentration, and hydrophobicity of the cathode gas diffuser.     

A transient two-phase mass transport model for liquid feed direct methanol fuel cells

A transient two-phase mass transport model for liquid feed direct methanol fuel cells (DMFCs) is developed. With this model, various processes that affect the DMFC transient behaviors are numerically studied. The results show that the cell voltage exhibits an overshoot behavior in response to a sudden change in the current density. The magnitude of the overshoot depends on the magnitudes of the change in the cell current density and the initial current density. It is found that the dynamic change in the methanol permeation through the membrane to the cathode results in a strong cathode overpotential overshoot, which is believed to be the predominant factor that leads to the cell voltage overshoot. In contrast, the anode overpotential is relatively insensitive to the changes in the methanol concentration as well as CO surface coverage in the anode catalyst layer. Moreover, the effect of the double layer capacitance (DLC) on the cell dynamic behavior is studied and the results show that the DLC can smoothen the change in the cell voltage in response to a change in the cell current density. Furthermore, the dynamic response of mass transport to a change in the cell current density is found to be rather slow. In particular, it is shown that the slow response in the mass transport of methanol is one of the key factors that influence the cell dynamic operation.     

An impedance study for the anode micro-porous layer in an operating direct methanol fuel cell

This study presents the benefit to an operating direct methanol fuel cell (DMFC) by coating a micro-porous layer (MPL) on the surface of anode gas diffusion layer (GDL). Taking the membrane electrode assembly (MEA) with and without the anodic MPL structure into account, the performances of the two types of MEA are evaluated by measuring the polarization curves together with the specific power density at a constant current density. Regarding the cell performances, the comparisons between the average power performances of the two different MEAs at low and high current density, various methanol concentrations and air flow rates are carried out by using the electrochemical impedance spectroscopy (EIS) technique. In contrast to conventional half cell EIS measurements, both the anode and cathode impedance spectra are measured in real-time during the discharge regime of the DMFC. As comparing each anode and cathode EIS between the two different MEAs, the influences of the anodic MPL on the anode and cathode reactions are systematically discussed and analyzed. Furthermore, the results are used to infer complete and reasonable interpretations of the combined effects caused by the anodic MPL on the full cell impedance, which correspond with the practical cell performance.     

A flow field enabling operating direct methanol fuel cells with highly concentrated methanol

In this work, an anode flow field that allows a direct methanol fuel cell (DMFC) to operate with highly concentrated methanol is developed and tested. The basic idea of this flow field design is to vaporize methanol solution in the flow field by utilizing the heat generated from the fuel cell so that the methanol concentration in the anode catalyst layer can be controlled to an appropriate level. The flow field is composed of two parallel flow channel plates, separated with a gap. The upper plate with a grooved serpentine flow channel is to vaporize a highly concentrated methanol solution to ensure the fuel to be completely vaporized before it enters the gap, while the lower plate, perforated to form a serpentine flow channel and located between the gap and the membrane electrode assembly (MEA), is to uniformly distribute the fuel onto the anode surface of the MEA. The test results show that this unique flow field design enables the DMFC operating with 16.0-M methanol to yield a power output similar to that with the conventional flow field design with 2.0-M methanol, significantly increasing the specific energy of the DMFC system. Finally, the effects of methanol solution flow rates and operating temperature on cell performance are investigated.     

Performance evaluation of direct methanol fuel cells for portable applications

This study examines the feasibility of powering a range of portable devices with a direct methanol fuel cell (DMFC). The analysis includes a comparison between a Li-ion battery and DMFC to supply the power for a laptop, camcorder and a cell phone. A parametric study of the systems for an operational period of 4 years is performed. Under the assumptions made for both the Li-ion battery and DMFC system, the battery cost is lower than the DMFC during the first year of operation. However, by the end of 4 years of operational time, the DMFC system would cost less. The weight and cost comparisons show that the fuel cell system occupies less space than the battery to store a higher amount of energy. The weight of both systems is almost identical. Finally, the CO₂ emissions can be decreased by a higher exergetic efficiency of the DMFC, which leads to improved sustainability.     

An algorithm for sensor-less fuel control of direct methanol fuel cells

We report an algorithm for real-time control of the fuel of a DMFC. The MEA voltage decay coefficients [e₁, e₂], and I-V-T, M′-I-T, and W′-I-T curves (where I is the current, V the voltage, T the temperature, and M′ and W′ the methanol and water consumption rates, respectively) of n fuels with specified methanol concentrations C_M,k (k = 1, 2,…, n) are pre-established and form (I,V,T), (M′,I,T), and (W′,I,T) surfaces for each C_M,k. The in situ measured (I,V,T)_u after voltage decay correction is applied to the n preset (I,V,T) surfaces to estimate C_M,u (the C_M corresponding to (I,V,T)_u) using an interpolation procedure. The C_M,u is then applied to the n preset (M′,I,T) and (W′,I,T) surfaces to estimate cumulated “methanol” and “water” consumed quantities . Thus in a real-time system, the C_M and total quantity of fuel can be controlled using the estimated C_M,u and cumulated “methanol” and “water” consumed quantities.     

Investigation on the durability of direct methanol fuel cells

This study addresses the durability of direct methanol fuel cells (DMFCs). Three performance indices including permanent degradation, temporary degradation and voltage fluctuation are proposed to qualify the durability of DMFC. The decay rate, associated with permanent degradation, follows from such failure mechanisms as dissolution, growth and poisoning of the catalyst, while temporary degradation reflects the elimination of the hydrophobic property of the gas diffusion layer (GDL). However, voltage fluctuations reveal different results which cannot stand for degradation phenomenon exactly. In this investigation, such methods of examination as scanning electron microscope (SEM), and X-ray diffraction (XRD) are employed to check the increase in the mean particle size in the anode and cathode catalysts, and the degree is higher in the cathode. The Ru content in the anode catalyst and the specific surface area (SSA) of the anode and cathode catalysts decrease after long-term operation. Moreover, the crossover of Ru from the anode side to the cathode side is revealed by energy dispersive X-ray (EDX) analysis. Electro-catalytic activity towards the methanol oxidation reaction (MOR) at the anode is verified to be weaker after durability test by cyclic voltammetry (CV). Also, the electrochemical areas (ECAs) of the anode and cathode catalysts are evaluated by hydrogen-desorption. SSA loss simply because of agglomeration and growth of the catalyst particles, of course, is lower than ECA loss. The observations will help to elucidate the failure mechanism of membrane electrode assembly (MEA) in durability tests, and thus help to prolong the lifetime of DMFC.     

Water management in direct methanol fuel cells

Water management is an important challenge in portable direct methanol fuel cells. Reducing the water and methanol loss from the anode to the cathode enables the use of highly concentrated methanol solutions to achieve enhanced performances. In this work, the results of a simulation study using a previous developed model for DMFCs are presented. Particular attention is devoted to the water distribution across the cell. The influence of different parameters (such as the cathode relative humidity (RH), the methanol concentration and the membrane, catalyst layer and diffusion media thicknesses) over the water transport and on the cell performance is studied. The analytical solutions of the net water transport coefficient, for different values of the cathode relative humidity are successfully compared with recent published experimental data putting in evidence that humidified cathodes contribute to a decrease on the water crossover. As a result of the modelling results, a tailored MEA build-up with the common available commercial materials is proposed to achieve low methanol and water crossover and high power density, operating at relatively high methanol concentrations. A thick anode catalyst layer to promote methanol oxidation, a thin anode gas diffusion layer as methanol carrier to the catalyst layer and a thin polymer membrane to lower the water crossover coefficient between the anode and cathode are suggested.     

Effect of operating conditions on water management of membrane electrode assembly for direct methanol fuel cell

介绍了直接甲醇燃料电池(DMFCs)膜电极的水平衡研究对单电池性能和稳定性的影响,研究了电池操作温度,空气流量及电流密度等操作条件对膜电极水平衡的影响.通过调节操作条件改变净水传输系数,进一步表征膜电极水平衡对电池稳定性的影响.结果表明,单电池在60 ℃,阴极常压空气80 mL/min进料,100 mA/cm²条件下工作具有较好的水平衡,最后,测试了单电池在该条件下的稳定性,测试结果表明电池稳定运行200 h后,性能没有明显衰减.