Phytosynthesized iron oxide nanoparticles and ferrous iron on fermentative hydrogen production using Enterobacter cloacae: Evaluation and comparison of the effects

The effects of FeSO₄ and synthesized iron oxide nanoparticles (0–250 mg/L) on fermentative hydrogen production from glucose and sucrose, using Enterobacter cloacae were investigated, to find out the enhancement of efficiency. The maximum hydrogen yields of 1.7 ± 0.017 mol H₂/mol glucose and 5.19 ± 0.12 mol H₂/mol sucrose were obtained with 25 mg/L of ferrous iron supplementation. In comparison, the maximum hydrogen yields of 2.07 ± 0.07 mol H₂/mol glucose and 5.44 ± 0.27 mol H₂/mol sucrose were achieved with 125 mg/L and 200 mg/L of iron oxide nanoparticles, respectively. These results indicate that the enhancement of hydrogen production on the supplementation of iron oxide nanoparticles was found to be considerably higher than that of ferrous iron supplementation. The activity of E. cloacae in a glucose and sucrose fed systems was increased by the addition of iron oxide nanoparticles, but the metabolic pathway was not changed. The results revealed that the glucose and sucrose fed systems conformed to the acetate/butyrate fermentation type.     

Biological hydrogen production by extremely thermophilic novel bacterium Thermoanaerobacter mathranii A3N isolated from oil producing well

Hydrogen producing novel bacterial strain was isolated from formation water from oil producing well. It was identified as Thermoanaerobacter mathranii A3N by 16S rRNA gene sequencing. Hydrogen production by novel strain was pH and substrate dependent and favored pH 8.0 for starch, pH 7.5 for xylose and sucrose, pH 8.0–9.0 for glucose fermentation at 70 °C. The highest H₂ yield was 2.64 ± 0.40 mol H₂ mol glucose at 10 g/L, 5.36 ± 0.41 mol H₂ mol – sucrose at 10 g/L, 17.91 ± 0.16 mmol H₂ g – starch at 5 g/L and 2.09 ± 0.21 mol H₂ mol xylose at 5 g/L. The maximum specific hydrogen production rates 6.29 (starch), 9.34 (sucrose), 5.76 (xylose) and 4.89 (glucose) mmol/g cell/h. Acetate-type fermentation pathway (approximately 97%) was found to be dominant in strain A3N, whereas butyrate formation was found in sucrose and xylose fermentation. Lactate production increased with high xylose concentrations above 10 g/L.     

Enhanced hydrogen production from xylose and bamboo stalk hydrolysate by overexpression of xylulokinase and xylose isomerase in Klebsiella oxytoca HP1

Biofuels production from lignocellulose hydrolysates by microbe fermentation has merited attention because of the mild reaction conditions involved and the clean nature of the process. In this work, xylulokinase (XK) and xylose isomerase (XI) were overexpressed in Klebsiella oxytoca HP1 to enhance hydrogen production by the fermentation of xylose. The recombinant strains exhibited higher enzyme activity of XI or XK compared with the wild strain. Hydrogen production from pure xylose, xylose/glucose mixtures and bamboo stalk hydrolysate was significantly enhanced with the overexpression of XI and XK in K. oxytoca HP1 in terms of total hydrogen yield (THY), hydrogen yield per mole substrate (HYPM) and hydrogen production rate (HPR). The HYPM of K. oxytoca HP1/xylB and K. oxytoca HP1/xylA reached 1.93 ± 0.05 and 2.46 ± 0.05 mol H₂/mol xylose, respectively in pure xylose, while the value for the wild strain was 1.68 ± 0.04 mol H₂/mol xylose. The xylose consumption rate (XCR) for the recombinant strain was significantly higher than that for the wild strain, particularly in the early stage of fermentation. Relative to the wild type, hydrogen yield (HY) from 1 g of preprocessed bamboo powder of HP1/xylB and HP1/xylA increased by 33.04 and 41.31%, respectively. It was concluded that overexpression of XK or XI was able to promote hydrogen production from xylose and xylose/glucose mixtures by simultaneously increasing the utilization efficiency of xylose and weakening the inhibitory effect of glucose on xylose use. In addition, the results indicated that overexpression technology was an effective way to further increase hydrogen production from lignocellulosic hydrolysates.     

Biohydrogen production by Thermoanaerobacterium thermosaccharolyticum TERI S7 from oil reservoir flow pipeline

Thermophilic dark fermentative hydrogen producing bacterial strain, TERI S7, isolated from an oil reservoir flow pipeline located in Mumbai, India, showed 98% identity with Thermoanaerobacterium thermosaccharolyticum by 16S rRNA gene analysis. It produced 1450–1900 ml/L hydrogen under both acidic and alkaline conditions; at a temperature range of 45–60 °C. The maximum hydrogen yield was 2.5 ± 0.2 mol H₂/mol glucose, 2.2 ± 0.2 mol H₂/mol xylose and 5.2 ± 0.2 mol H₂/mol sucrose, when the respective sugars were used as carbon source. The cumulative hydrogen production, hydrogen production rate and specific hydrogen production rate by the strain TERI S7 with sucrose as carbon source was found to be 1704 ± 105 ml/L, 71 ± 6 ml/L/h and 142 ± 13 ml/g/h respectively. Major soluble metabolites produced during fermentation were acetic acid and butyric acid. The strain TERI S7 was also observed to produce hydrogen continuously up to 48 h at pH 3.9.     

Biohydrogen production from xylose by Thermoanaerobacterium thermosaccharolyticum KKU19 isolated from hot spring sediment

A thermophilic hydrogen producer was isolated from hot spring sediment and identified as Thermoanaerobacterium thermosaccharolyticum KKU19 by biochemical tests and 16S rRNA gene sequence analysis. The strain KKU19 showed the ability to utilize various kinds of carbon sources. Xylose was the preferred carbon source while peptone was the preferred organic nitrogen source. The optimum conditions for hydrogen production and cell growth on xylose were an initial pH of 6.50, temperature of 60 °C, a carbon to nitrogen ratio of 20:1, and a xylose concentration of 10.00 g/L. This resulted in a maximum cumulative hydrogen production, hydrogen production rate and hydrogen yield of 3020 ± 210 mL H₂/L, 3.95 ± 0.20 mmol H₂/L h and 2.09 ± 0.02 mol H₂/mol xylose consumed, respectively. Acetic and butyric acids were the main soluble metabolite products suggesting acetate and butyrate type fermentation.     

The production of biohydrogen by a novel strain Clostridium sp. YM1 in dark fermentation process

In view of increasing attempts for the production of renewable energy, the production of biohydrogen energy by a new mesophilic bacterium Clostridium sp. YM1 was performed for the first time in the dark fermentation. Experimental results showed that the fermentative hydrogen was successfully produced by Clostridium sp. YM1 with the highest cumulative hydrogen volume of 3821 ml/L with a hydrogen yield of 1.7 mol H₂/mol glucose consumed. Similar results revealed that optimum incubation temperature and pH value of culture medium were 37 °C and 6.5, respectively. The study of hydrogen production from glucose and xylose revealed that this strain was able to generate higher hydrogen from glucose compared to that from xylose. The profile of volatile fatty acids produced showed that hydrogen generation by Clostridium sp. YM1 was butyrate-type fermentation. Moreover, the findings of this study indicated that an increase in head space of fermentation culture positively enhanced hydrogen production.     

Impact of regulated pH on proto scale hydrogen production from xylose by an alkaline tolerant novel bacterial strain, Enterobacter cloacae DT-1

A hydrogen producing facultative anaerobic alkaline tolerant novel bacterial strain was isolated from crude oil contaminated soil and identified as Enterobacter cloacae DT-1 based on 16S rRNA gene sequence analysis. DT-1 strain could utilize various carbon sources; glycerol, CMCellulose, glucose and xylose, which demonstrates that DT-1 has potential for hydrogen generation from renewable wastes. Batch fermentative studies were carried out for optimization of pH and Fe²⁺ concentration. DT-1 could generate hydrogen at wide range of pH (5–10) at 37 °C. Optimum pH was; 8, at which maximum hydrogen was obtained from glucose (32 mmol/L), when used as substrate in BSH medium containing 5 mg/L Fe²⁺ ion. Decrease in hydrogen partial pressure by lowering the total pressure in the fermenter head space, enhanced the hydrogen production performance of DT-1 from 32 mmol H₂/L to 42 mmol H₂/L from glucose and from 19 mmol H₂/L to 33 mmol H₂/L from xylose. Hydrogen yield efficiency (HY) of DT-1 from glucose and xylose was 1.4 mol H₂/mol glucose and 2.2 mol H₂/mol xylose, respectively. Scale up of batch fermentative hydrogen production in proto scale (20 L working volume) at regulated pH, enhanced the HY efficiency of DT-1 from 2.2 to 2.8 mol H₂/mol xylose (1.27 fold increase in HY from laboratory scale). 84% of maximum theoretical possible HY efficiency from xylose was achieved by DT-1. Acetate and ethanol were the major metabolites generated during hydrogen production.     

Influence of linoleic acid,pH and HRT on anaerobic microbial populations and metabolic shifts in ASBRs during dark hydrogen fermentation of lignocellulosic sugars

In this study, controlling an anaerobic microbial community to increase the hydrogen (H₂) yield during the degradation of lignocelluosic sugars was accomplished by adding linoleic acid (LA) at low pH and reducing the hydraulic retention time (HRT) of an anaerobic sequencing batch reactor (ASBR). At pH 5.5 and a 1.7 d HRT, the maximum H₂ yield for LA treated cultures fed glucose or xylose reached 2.89 ± 0.18 mol mol⁻¹ and 1.94 ± 0.17 mol mol⁻¹, respectively. The major soluble metabolites at pH 5.5 with a 1.7 day HRT differed between the control and LA treated cultures. A metabolic shift toward H₂ production resulted in increased hydrogenase activity in both the xylose (13%) and glucose (34%) fed LA treated cultures relative to the controls. In addition, the Clostridia population and the H₂ yield were elevated in cultures treated with LA. A flux balance analysis for the LA treated cultures showed a reduction in homoacetogenic activity which was associated with reducing the Bacteriodes levels from 12% to 5% in the glucose fed cultures and 16% to 10% in the xylose fed cultures. Strategies for controlling the homoacetogens and optimal hydrogen production from glucose and xylose are proposed.     

Hydrogen production from acid and enzymatic oat straw hydrolysates in an anaerobic sequencing batch reactor: Performance and microbial population analysis

Feasibility of hydrogen production from acid and enzymatic oat straw hydrolysates was evaluated in an anaerobic sequencing batch reactor at 35 °C and constant substrate concentration (5 g chemical oxygen demand/L). In a first experiment, hydrogen production was replaced by methane production. Selective pressures applied in a second experiment successfully prevented methane production. During this experiment, initial feeding with glucose/xylose, as model substrates, promoted biomass granulation. Also, the highest hydrogen molar yield (HMY, 2 mol H₂/mol sugar consumed) and hydrogen production rate (HPR, 278 mL H₂/L-h) were obtained with these model substrates. Gradual substitution of glucose/xylose by acid hydrolysate led to disaggregation of granules and lower HPR and HMY. When the model substrates were completely substituted by enzymatic hydrolysate, the HMY and HPR were 0.81 mol H₂/mol sugar consumed and 29.6 mL H₂/L-h, respectively. Molecular analysis revealed a low bacterial diversity in the stages with high hydrogen production and vice versa. Furthermore, Clostridium pasteurianum was identified as the most abundant species in stages with a high hydrogen production. Despite that feasibility of hydrogen production from hydrolysates was demonstrated, lower performance from hydrolysates than from model substrates was obtained.     

Biohydrogen production from various feedstocks by Bacillus firmus NMBL-03

In present work our objective was to find out the potential substrates for fermentative hydrogen production using microbial culture of Bacillus firmus NMBL-03 isolated from municipal sludge. A wide variety of substrates (glucose, xylose, arabinose, lactose, sucrose, and starch) and carbohydrate rich waste products (bagasse hydrolysate, molasses, potato peel and cyanobacterial mass) have been used for dark fermentative hydrogen production. All studies were done at optimized physico-chemical conditions. Among all substrates glucose, arabinose, lactose, starch, molasses and bagasse hydrolysate were found to be the favorable substrates for hydrogen production. The highest VHPR i.e. 177.5 ± 7.07 ml/L.h (7.95 ± 0.29 mmol H₂/L.h) and maximum H₂ production (22.58 ± 2.65 mmol H₂/L) was achieved using starch as the substrate. The maximum yield 1.29 ± 0.11 mol H₂/mol reducing sugar was obtained from bagasse hydrolysate as substrate. Butyrate and acetate were detected as the end product in all the cases while lactate was also detected from glucose and cyanobacterial hydrolysate. Since considerable amount of H₂ also evolved when cyanobacterial mass was used, therefore this microbe can be exploited for hydrogen production through a three stage integrated system. Residual carbohydrate containing biomass left after cyanobacterial H₂ production can be utilized in dark fermentative H₂ production. Spent media obtained after dark fermentative H₂ production contain considerable amount of volatile fatty acids that can be potential substrate for photo fermentative H₂ production.     

Fermentative hydrogen production from different sugars by Citrobacter sp. CMC-1 in batch culture

In this study, production of hydrogen (H₂) from glucose, xylose, galactose, mannose, arabinose and rhamnose by a strain isolated from activated sludge was investigated. The strain, named as Citrobacter sp. CMC-1, was enriched in cellobiose amended minimal media. Based on 16S rRNA sequence, the CMC-1 strain is a close relative of Citrobacter amalonaticus strain SA01 (99%). Optimal cultivation parameters for H₂ production and growth such as pH and temperature were investigated. H₂ yields from glucose at optimal conditions (pH 6.0 and 34 °C) were 1.82 ± 0.02 mol-H₂/mol-glucose. Strain CMC-1 fermented galactose, mannose, xylose, arabinose and rhamnose. After 48 h incubation, the strain CMC-1 completely fermented all sugars tested, except arabinose. Increase in fermentation period lowered residual formate level in the media and improved H₂ production for galactose, mannose and xylose (1.68 ± 0.24, 1.93 ± 0.14 and 1.63 ± 0.07 mol-H₂/mol-substrate respectively).     

Biohydrogen production from ricebran using Clostridium saccharoperbutylacetonicum N1-4

Treated ricebran hydrolysate was fermented anaerobically using Clostridium saccharoperbutylacetonicum N1-4 at an initial pH of 6 ± 0.2 and an operating temperature of 30 °C for production of hydrogen. The effects of different pretreatment methods on the liberation of sugar from 100 g of ricebran per litre of medium (distilled water) were investigated. In addition, the effects of the pretreatment method on ricebran hydrolysates of different initial ricebran concentrations on liberated sugar as well as the effects of the initial inoculum concentration, ricebran (substrate) concentration, and FeSO₄·7H₂O concentration on the yield as well as the productivity of hydrogen were investigated. The combination of enzymatic hydrolysis and a boiling pretreatment method produced the most fermentable sugar, 29.03 ± 0.0 g/L from 100 g of ricebran per litre of medium (distilled water), while the amount of sugar liberated by ricebran hydrolysates of different initial ricebran concentrations upon pretreatment monotonically increased with the initial ricebran concentration. The increment in substrate, inoculum, and FeSO₄·7H₂O concentrations had a significantly positive effect (p < 0.05) on both the yield and productivity of hydrogen. The maximum hydrogen gas yield (Y_P/S) and productivity of 3.37 mol-H₂ per mol-sugar consumed and 7.58 mmol/(L h), respectively, were obtained from ricebran hydrolysate with a 100 g/L ricebran concentration (equivalent to 28.59 ± 1.27 g sugar/L). In other experiments, 0.03 g/L FeSO₄·7H₂O and 1.5 g/L inoculum resulted in the best hydrogen gas yield and productivity from ricebran hydrolysates.     

Fermentative hydrogen production by new marine Clostridium amygdalinum strain C9 isolated from offshore crude oil pipeline

The present study investigated hydrogen production potential of novel marine Clostridium amygdalinum strain C9 isolated from oil water mixtures. Batch fermentations were carried out to determine the optimal conditions for the maximum hydrogen production on xylan, xylose, arabinose and starch. Maximum hydrogen production was pH and substrate dependant. The strain C9 favored optimum pH 7.5 (40 mmol H₂/g xylan) from xylan, pH 7.5–8.5 from xylose (2.2–2.5 mol H₂/mol xylose), pH 8.5 from arabinose (1.78 mol H₂/mol arabinose) and pH 7.5 from starch (390 ml H₂/g starch). But the strain C9 exhibited mixed type fermentation was exhibited during xylose fermentation. NaCl is required for the growth and hydrogen production. Distribution of volatile fatty acids was initial pH dependant and substrate dependant. Optimum NaCl requirement for maximum hydrogen production is substrate dependant (10 g NaCl/L for xylose and arabinose, and 7.5 g NaCl/L for xylan and starch).     

Dark fermentative hydrogen production from xylose by a hot spring enrichment culture

Dark fermentative hydrogen production by a hot spring culture was studied from different sugars in batch assays and from xylose in continuous stirred tank reactor (CSTR) with on-line pH control. Batch assays yielded hydrogen in following order: xylose > arabinose > ribose > glucose. The highest hydrogen yield in batch assays was 0.71 mol H₂/mol xylose. In CSTR the highest H₂ yield and production rate at 45 °C were 1.97 mol H₂/mol xylose and 7.3 mmol H₂/h/L, respectively, and at 37 °C, 1.18 mol H₂/mol xylose and 1.7 mmol H₂/h/L, respectively. At 45 °C, microbial community consisted of only two bacterial strains affiliated to Clostridium acetobutulyticum and Citrobacter freundii, whereas at 37 °C six Clostridial species were detected. In summary hydrogen yield by hot spring culture was higher with pentoses than hexoses. The highest H₂ production rate and yield and thus, the most efficient hydrogen producing bacteria were obtained at suboptimal temperature of 45 °C for both mesophiles and thermophiles.     

Direct fermentation of Laminaria japonica for biohydrogen production by anaerobic mixed cultures

A few studies have been made on fermentative hydrogen production from marine algae, despite of their advantages compared with other biomass substrates. In this study, fermentative hydrogen production from Laminaria japonica (one brown algae species) was investigated under mesophilic condition (35 ± 1 °C) without any pretreatment method. A feasibility test was first conducted through a series of batch cultivations, and 0.92 mol H₂/mol hexose_added, or 71.4 ml H₂/g TS of hydrogen yield was achieved at a substrate concentration of 20 g COD/L (based on carbohydrate), initial pH of 7.5, and cultivation pH of 5.5. Continuous operation for a period of 80 days was then carried out using anaerobic sequencing batch reactor (ASBR) with a hydraulic retention time (HRT) of 6 days. After operation for approximately 30 days, a stable hydrogen yield of 0.79 ± 0.03 mol H₂/mol hexose_added was obtained. To optimize bioenergy recovery from L. japonica, an up-flow anaerobic sludge blanket reactor (UASBr) was applied to treat hydrogen fermentation effluent (HFE) for methane production. A maximum methane yield of 309 ± 12 ml CH₄/g COD was achieved during the 90 days operation period, where the organic loading rate (OLR) was 3.5 g COD/L/d.     

Hydrogen metabolism in the extreme thermophile Thermotoga neapolitana

Anaerobic growth of Thermotoga neapolitana led maximum to hydrogen yield of 3.85 ± 0.07 mol H₂/mol glucose and production rate of 51 ml/l/h. This productivity is strongly affected by stirring, pH buffering, N₂ sparging and culture/headspace volume ratio. Embden–Meyerhoff pathway is the only glycolytic route in T. neapolitana but, under the conditions used in this study, about 12–15% of the biogas requires consumption of protein source. Reduction of the hydrogen yields below the theoretical 4 mol H₂/mol glucose is mainly due to production of lactate and alanine that affect the availability of pyruvate/NADH for the hydrogenase, as well as to loss of part of glucose by conversion to fructose that is eventually released in the medium. Hydrogen productivity is modulated during the bacterial growth and major biogas synthesis is recorded in the stationary phase in concomitance with reduction of lactate synthesis. Apparently, this event is not consistent with an equal increase in acetate production. In agreement with the hydrogenase model recently proposed for the sister species Thermotoga maritima, this suggests that cellular NADH⁺ ratio has a crucial role on biogas synthesis.     

Optimization of thermophilic fermentative hydrogen production by the newly isolated Caloranaerobacter azorensis H53214 from deep-sea hydrothermal vent environment

A unique thermophilic fermentative hydrogen-producing strain H53214 was isolated from a deep-sea hydrothermal vent environment, and identified as Caloranaerobacter azorensis based on bacterial 16S rRNA gene analysis. The optimum culture condition for hydrogen production by the bacterium, designated C. azorensis H53214, was investigated by the response surface methodology (RSM). Eight variables including the concentration of NaCl, glucose, yeast, tryptone, FeSO₄ and MgSO₄, initial pH and incubation temperature were screened based on the Plackett–Burman design. The results showed that initial pH, tryptone and yeast were significant variables, which were further optimized using the steepest ascent method and Box–Behnken design. The optimal culture conditions for hydrogen production were an initial pH of 7.7, 8.3 g L⁻¹ tryptone and 7.9 g L⁻¹ yeast. Under these conditions, the maximum cumulative hydrogen volume, hydrogen yield and maximum H₂ production rate were 1.58 L H₂ L⁻¹ medium, 1.46 mol H₂ mol⁻¹ glucose and 25.7 mmol H₂ g⁻¹ cell dry weight (CDW) h⁻¹, respectively. By comparison analysis, strain H53214 was superior to the most thermophilic hydrogen producers because of the high hydrogen production rate. In addition, the isolation of C. azorensis H53214 indicated the deep-sea hydrothermal environment might be a potential source for fermentative hydrogen-producing thermophiles.     

Statistical optimization of medium components affecting simultaneous fermentative hydrogen and ethanol production from crude glycerol by thermotolerant Klebsiella sp. TR17

A thermotolerant Klebsiella sp. TR17 for production of hydrogen from crude glycerol was investigated. Results from Plackett–Burman design indicated that the significant variables, which influenced hydrogen production, were KH₂PO₄ and NH₄Cl (for buffer capacity and nitrogen source). Subsequently, the two selected variables and crude glycerol were optimized by the Central Composite design for achieving maximum hydrogen and ethanol yield. The concentration of crude glycerol, KH₂PO₄, and NH₄Cl had an individual effect on both hydrogen and ethanol yield (p < 0.05), while KH₂PO₄ and NH₄Cl had an interactive effect on ethanol yield (p < 0.05). The optimum medium components were 11.14 g/L crude glycerol, 2.47 g/L KH₂PO₄, and 6.03 g/L NH₄Cl. The predicted maximum simultaneous hydrogen and ethanol yield were 0.27 mol H₂/mol glycerol and 0.63 mol EtOH/mol glycerol, respectively. Validation of the predicted optimal conditions exhibited similar hydrogen and ethanol yield of 0.26 mol H₂/mol glycerol and 0.58 mol EtOH/mol glycerol, respectively.     

Dark fermentative biohydrogen production by mesophilic bacterial consortia isolated from riverbed sediments

Dark fermentative bacterial strains were isolated from riverbed sediments and investigated for hydrogen production. A series of batch experiments were conducted to study the effect of pH, substrate concentration and temperature on hydrogen production from a selected bacterial consortium, TERI BH05. Batch experiments for fermentative conversion of sucrose, starch, glucose, fructose, and xylose indicated that TERI BH05 effectively utilized all the five sugars to produce fermentative hydrogen. Glucose was the most preferred carbon source indicating highest hydrogen yields of 22.3 mmol/L. Acetic and butyric acid were the major soluble metabolites detected. Investigation on optimization of pH, temperature, and substrate concentration revealed that TERI BH05 produced maximum hydrogen at 37 °C, pH 6 with 8 g/L of glucose supplementation and maximum yield of hydrogen production observed was 2.0–2.3 mol H₂/mol glucose. Characterization of TERI BH05 revealed the presence of two different bacterial strains showing maximum homology to Clostridium butyricum and Clostridium bifermentans.     

Hydrogen production from soft-drink wastewater in an upflow anaerobic packed-bed reactor

The production of hydrogen from soft-drink wastewater in two upflow anaerobic packed-bed reactors was evaluated. The results show that soft-drink wastewater is a good source for hydrogen generation. Data from both reactors indicate that the reactor without medium containing macro- and micronutrients (R2) provided a higher hydrogen yield (3.5 mol H₂ mol⁻¹ of sucrose) as compared to the reactor (R1) with a nutrient-containing medium (3.3 mol H₂ mol⁻¹ of sucrose). Reactor R2 continuously produced hydrogen, whereas reactor R1 exhibited a short period of production and produced lower amounts of hydrogen. Better hydrogen production rates and percentages of biogas were also observed for reactor R2, which produced 0.4 L h⁻¹ L⁻¹ and 15.8% of H₂, compared to reactor R1, which produced 0.2 L h⁻¹ L⁻¹ and 2.6% of H₂. The difference in performance between the reactors was likely due to changes in the metabolic pathway for hydrogen production and decreases in bed porosity as a result of excessive biomass growth in reactor R1. Molecular biological analyses of samples from reactors R1 and R2 indicated the presence of several microorganisms, including Clostridium (91% similarity), Enterobacter (93% similarity) and Klebsiella (97% similarity).