Remarkable promotion of photocatalytic hydrogen evolution from water on TiO2-pillared titanoniobate

TiO₂-pillared titanoniobate TiO₂/HTiNbO₅ as an efficient photocatalyst was prepared via an exfoliation–restacking route. The as-prepared nanohybrid is mesoporous with a high specific surface area of 171 m²/g and a gallery height of 1.55 nm. Under a 300 W Xe lamp irradiation, the nanohybrid exhibited a high photocatalytic activity of 219 μmol/h/(g cat) in splitting water into hydrogen, which is 12 times as high as its parent HTiNbO₅ (18 μmol/h/g) and 24 times as TiO₂ (9 μmol/h/g). Enlarged surface area and effective electronic coupling between the host and the guest components contribute to the high photocatalytic activity of TiO₂/HTiNbO₅. Its photocatalytic activity was further improved through platinizing, and 5 wt% Pt-loaded TiO₂/HTiNbO₅ gave a remarkable hydrogen evolution rate of 4735 μmol/h/g. A photoexcitation model of the semiconductor–semiconductor pillared photocatalyst was proposed based on the results of XPS and UV–vis.     

Role of molecular oxygen on the synthesis of Ni(OH)2/TiO2 photocatalysts and its effect on solar hydrogen production activity

Molecular oxygen performs a vital role in the photocatalytic activity of anatase TiO₂, but there is a little experimental insight into the role of molecular oxygen on the synthesis of TiO₂ based photocatalysts. Herein, we have shown that Ni(OH)₂/TiO₂ prepared in the presence and absence of molecular oxygen results in significantly varied hydrogen production activity. The sample synthesized in the presence of O₂ and N₂ produced 6624 μmol/h/g and 4468 μmol/h/g of hydrogen under direct solar light exposure. Additionally, the samples prepared in the presence of light irradiation produced 8289 μmol/h/g of hydrogen, a 72 fold jump in hydrogen production compared to TiO₂. XPS, FTIR, Raman, and ESR measurements were carried out to investigate the underlined mechanism for such variation in the photocatalytic activity. Our results suggest that the presence of molecular oxygen during Ni(OH)₂/TiO₂ synthesis causes the formation of terminal OH and reduced the oxygen vacancies on the surface of TiO₂, which can significantly alter the H₂ production. Also, the reusability of the photocatalysts is greatly affected by the synthesis conditions, namely the presence of light and molecular oxygen.     

Photocatalytic hydrogen production from aqueous methanol solution with CuO/Al2O3/TiO2 nanocomposite

The photocatalytic hydrogen production from aqueous methanol solution was investigated with ZnO/TiO₂, SnO/TiO₂, CuO/TiO₂, Al₂O₃/TiO₂ and CuO/Al₂O₃/TiO₂ nanocomposites. A mechanical mixing method, followed by the solid-state reaction at elevated temperature, was used for the preparation of nanocomposite photocatalyst. Among these nanocomposite photocatalysts, the maximal photocatalytic hydrogen production was observed with CuO/Al₂O₃/TiO₂ nanocomposites. A variety of components of CuO/Al₂O₃/TiO₂ photocatalysts were tested for the enhancement of H₂ formation. The optimal component was 0.2 wt% CuO/0.3 wt% Al₂O₃/TiO₂. The activity exhibited approximately tenfold enhancement at the optimum loading, compared with that with pure P-25 TiO₂. Nano-sized TiO₂ photocatalytic hydrogen technology has great potential for low-cost, environmentally friendly solar-hydrogen production to support the future hydrogen economy.     

Efficient indium tin oxide/Cr-doped-TiO2 multilayer thin films for H2 production by photocatalytic water-splitting

Cr-doped-TiO₂ thin films, with three different Cr concentrations (2, 5.5, and 9 at.%), have been synthesized by radio-frequency magnetron sputtering in order to sensitize TiO₂ in visible light. UV–visible spectra showed that maximum narrowing (2.1 eV) of the TiO₂ band gap is obtained for the highest Cr concentration. However, negligible photocurrent was measured with Indium Tin Oxide (ITO)/Cr-doped-TiO₂ (9 at.%) single bilayer sample due to the increased recombination rate of the photo-generated charges on the defects associated to the Cr³⁺ ions. To lower the charge recombination rate in the Cr-doped-TiO₂, multilayer films with different numbers of ITO/Cr-doped-TiO₂ (9 at.%) bilayers (namely, 3-, 4-, 5-, 6- and 7-bilayers) were deposited by keeping the total thickness of TiO₂ constant in each multilayer film. When the multilayer films were exposed to visible light, we observed that the photocurrent increases as function of the number of bilayers by reaching the maximum with 6-bilayers of ITO/Cr-doped-TiO₂. The enhanced photocurrent is attributed to: 1) higher absorption of visible light by Cr-doped-TiO₂, 2) number of space charge layers in form of ITO/TiO₂ interfaces in multilayer films, and 3) generation of photoelectrons just in/or near to the space charge layer by decreasing the Cr-doped-TiO₂ layer thickness. The reduced charge recombination rate in multilayer films was also confirmed by studying the photocurrent kinetic curve. The superior photocatalytic efficiency of the 6-bilayers film implies higher hydrogen production rate through water-splitting: we obtained indeed 24.4 μmol/h of H₂ production rate, a value about two times higher than that of pure TiO₂ (12.5 μmol/h).     

Improving hydrogen production via water splitting over Pt/TiO2/activated carbon nanocomposite

Mesoporous TiO₂/AC, Pt/TiO₂ and Pt/TiO₂/AC (AC = activated carbon) nanocomposites were synthesized by functionalizing the activated carbon using acid treatment and sol–gel method. Photochemical deposition method was used for Pt loading. The nano-photocatalysts were characterized using XRD, SEM, DRS, BET, FTIR, XPS, CHN and ICP methods. The hydrogen production, under UV light irradiation in an aqueous suspension containing methanol has been studied. The effect of Pt, methanol and activated carbon were investigated. The results show that the activated carbon and Pt together improve the hydrogen production via water splitting. Also methanol acts as a good hole scavenger. Mesoporous Pt/TiO₂/AC nanocomposite is the most efficient photocatalyst for hydrogen production compared to TiO₂/AC, Pt/TiO₂ and the commercial photocatalyst P25 under the same photoreaction conditions. Using Pt/TiO₂/AC, the rate of hydrogen production is 7490 μmol (h g catal.)⁻¹ that is about 75 times higher than that of the P25 photocatalyst.     

Structural properties of CuO/TiO2 nanorod in relation to their catalytic activity for simultaneous hydrogen production under solar light

CuO was introduced into porous TiO₂ nanorod through impregnation method. Before the impregnation step, TiO₂ nanorod was hydrothermally synthesized from TiO₂ powder in aqueous NaOH solution and followed by thermal treatment at 450 °C. The structures and properties of impregnated samples were characterized using various techniques, including XRD, BET, XAS, TEM, and UV-DRS. Their photocatalytic performance on simultaneous hydrogen production from pure water and aqueous methanol solution was also investigated under solar light. It was found that CuO/TiO₂ nanorod possessed a high surface area, good photocatalytic property and excellent hydrogen generation activity. Incorporation of Cu ions into the lattice framework of anatase TiO₂ nanorod enhanced the efficiency in visible region at 438–730 nm. Moreover, the XAS results showed that some Cu ions formed solid solution in the TiO₂ nanorod (Cu_xT_1−xO₂). However, the excessive incorporation of Cu ions did not improve any ability of anatase TiO₂ nanorod for production of hydrogen from pure water splitting. This could be due to the excessive CuO agglomeration at outside-pores which blocked the sensitization of TiO₂ nanorod. Only 1% Cu/TiO₂ nanorod was found to be a remarkable and an efficient photocatalyst for hydrogen production under solar light from both pure water and sacrificial methanol splitting. The highest rate of hydrogen production of 139.03 μmol h⁻¹ g_catalyst⁻¹ was found in sacrificial methanol which was 3.24% higher than in pure water.     

Hydrogen production by photocatalytic water-splitting using Cr- or Fe-doped TiO2 composite thin films photocatalyst

Cr- or Fe-ion-doped TiO₂ thin films have been synthesized by radio-frequency magnetron sputtering and a sol–gel method to study hydrogen generation by photocatalytic water-splitting under visible light irradiation. The doping method, dopant concentration, charge transfer from metal dopants to TiO₂, and type of dopants used for modification of TiO₂ were investigated for their ability to enhance photocatalytic activity. UV–Visible spectra show that the metal-doped-TiO₂ obtained by sputtering is much more efficient than that obtained by the sol–gel technique at inducing a red shift of the absorption edge in the visible light range. Low concentration metal ion doping must be done near the conducting indium tin oxide (ITO) – TiO₂ interface to avoid the formation of recombination centers for photo-generated electron–hole pairs. H₂ production rate (μmol/h) is higher for Fe-doped TiO₂ (15.5 μmol/h) than for Cr-doped TiO₂ (5.3 μmol/h) due to the ability of Fe ions to trap both electrons and holes, thus avoiding recombination, while Cr can only trap one type of charge carrier. A constant H₂ generation rate is obtained for long periods of time by all the investigated TiO₂ films because of the separate evolution of H₂ and O₂ gases, thus eliminating the back-reaction effect.     

TiO2 and TiO2–SiO2 thin films and powders by one-step soft-solution method: Synthesis and characterizations

Simple soft-solution method has been developed to synthesize films and powders of TiO₂ and mixed TiO₂–SiO₂ at relatively low temperatures. This method is simple and inexpensive. Furthermore, reactor can be designed for large-scale applications as well as to produce large quantities of composite powders in a single step. For the preparation of TiO₂, we used aqueous acidic medium containing TiOSO₄ and H₂O₂, which results in a peroxo-titanium precursor while colloidal SiO₂ has been added to the precursor for the formation of TiO₂–SiO₂. Post annealing at 500 °C is necessary to have anatase structure. Resulting films and powders were characterized by different techniques. TiO₂ (anatase) phase with (1 0 1) preferred orientation has been obtained. Also in TiO₂–SiO₂ mixed films and powders, TiO₂ (anatase) phase was found. Fourier transform infrared spectroscopy (FTIR) results for TiO₂ and mixed TiO₂–SiO₂ films have been presented and discussed. The method developed in this paper allowed obtaining compact and homogeneous TiO₂ films. These compact films are highly photoactive when TiO₂ is used as photo anode in an photoelectrochemical cell. Nanoporous morphology is obtained when SiO₂ colloids are added into the solution.     

Photocatalytic production of hydrogen and methane from glycerol reforming over Pt/TiO2–Nb2O5

In this study, platinized mixed oxides (TiO₂–Nb₂O₅) were tested on photocatalytic hydrogen production from a glycerol solution under UV light. Different samples with different Ti:Nb ratios were prepared by using a simple method that simultaneously combined a physical mixture and a platinum photochemical reduction. This method led to improved physicochemical properties such as low band gap, better Pt nanoparticle distribution on the surface, and the formation of different Pt species. Niobia content was also found to be an important factor in determining the overall efficiency of the Pt–TiO₂–Nb₂O₅ photocatalyst in the glycerol reforming reaction. The photocatalytic results showed that Pt on TiO₂–Nb₂O₅ enhanced hydrogen production from the aqueous glycerol solution at a 5 wt% initial glycerol concentration. The influence of different operating conditions such as the catalyst dosage and initial glycerol concentration was also evaluated. The results indicated that the best hydrogen and methane production was equal to 6657 μmol/L and 194 μmol/L, respectively after 4 h of UV radiation using Pt/Ti:Nb (1:2) sample and with 3 g/L of catalyst dosage. Moreover, the role of water in photocatalytic hydrogen production was studied through photocatalytic activity tests in the presence of D₂O. The obtained results confirmed the role of water molecules on the photocatalytic production of hydrogen in an aqueous glycerol solution.     

Light-assisted synthesis of Au/TiO2 nanoparticles for H2 production by photocatalytic water splitting

A series of Au/TiO₂ photocatalysts was synthesized via the light assistance through the photo-deposition for H₂ production by photocatalytic water splitting using ethanol as the hole scavenger. Effect of solution pH in the range of 3.2–10.0 on the morphology and photocatalytic activity for H₂ production of the obtained Au/TiO₂ photocatalysts was explored. It was found that all Au/TiO₂ photocatalysts prepared in different solution pH exhibited comparable anatase fraction (～0.84–0.85) and crystallite size of TiO₂ (21–22 nm), but showed different quantity of deposited Au nanoparticles (NPs) and other properties, particularly the particle size of the Au NPs. Among all prepared Au/TiO₂ photocatalysts, the Au/TiO₂ (10.0) photocatalyst exhibited the highest photocatalytic activity for H₂ production, owning to its high metallic state and small size of Au NPs. Via this photocatalyst, the maximum H₂ production of 296 μmol (～360 μmol/g?h) was gained at 240 min using the 30 vol% ethanol as the hole scavenger at the photocatalyst loading of 1.33 g/L under the UV light intensity of 0.24 mW/cm² with the quantum efficiency of 61.2% at 254 nm. The loss of the photocatalytic activity of around 20% was observed after the 5th use.     

Facile fabrication of Bi2O3/TiO2-xNx nanocomposites for excellent visible light driven photocatalytic hydrogen evolution

Mesoporous Bi₂O₃/TiO_2−xN_x nanocomposites (BiNT) were synthesized by soft chemical template free homogeneous co-precipitation technique. XRD, XPS, TEM, UV-Vis DRS and photoluminescence studies were adapted to determine the structural, electronic and optical properties. The photocatalytic activities of the catalysts were evaluated for water splitting to generate clean hydrogen fuel under visible light irradiation (λ ≥ 400 nm). BiNT-400 catalyst showed highest results towards hydrogen production (198.4 μmol/h) with an apparent quantum efficiency of 4.3%. The pronounced activity of BiNT-400 sample towards hydrogen production was well consistent with high crystallinity, large surface area, proper excitation by N doping and Bi₂O₃ sensitization.     

Rational design and fabrication of TiO2 nano heterostructure with multi-junctions for efficient photocatalysis

In addition to the extended light absorption, the effective spatial charge separation is a crucial factor for highly efficient metal-oxide semiconductor-based photocatalysts. Herein, a rational design of metal-semiconductor-metal nano heterostructure for enhancing photocatalytic performance is proposed. The semiconductor nanoparticles are integrated with two metals in one single nano heterostructure. The disordered layers are induced on the surface of TiO₂ to promote the light absorption capacity. More importantly, the n-n⁺ junction is fabricated at the contact region between crystalline TiO₂ (n-TiO₂) and disordered layers (n⁺-TiO₂). Besides, the Schottky diode and Ohmic contact are formed on n-TiO₂ and n⁺-TiO₂, respectively. As a result, the existence of multi-junctions leads to the formation of multiple continuous built-in electric fields, thus remarkably accelerating the spatial separation of charge carriers. The resulting nano heterostructure with multi-junctions (Pt–TiO₂–H–Ag) exhibits remarkably promoted photocatalytic performance. The maximum hydrogen generation rate of Pt–TiO₂–H–Ag under solar illumination (18001.0 μmol/h/g) is 8.3, 9.3, and 1.5 times superior to that of Pt-loaded P25 (Pt–P25), Pt loaded TiO₂ (Pt–TiO₂), and hydrogenated Pt–TiO₂ (Pt–TiO₂–H), respectively. Moreover, the photocatalytic performance under visible illumination is significantly enhanced by Pt–TiO₂–H–Ag. Specifically, the H₂ generation rate of Pt–TiO₂–H–Ag (2382.7 μmol/h/g) is about 15.1, 17.2, and 1.4 times higher than that of Pt–P25, Pt–TiO₂, and Pt–TiO₂–H, respectively. The corresponding apparent quantum efficiency of Pt–TiO₂–H–Ag is 15.8% (420 nm). The nano heterostructure with multi-junctions also exhibits excellent stability after five cycles, remaining hydrogen evolution rates of 15581.5 and 2211.4 μmol/h/g under solar and visible illumination, respectively. This effective and controllable manufacturing strategy could provide new opportunities to simultaneously extend optical absorption and facilitate the spatial charge separation and transport of wide-bandgap metal-oxide semiconductors.     

Carbon-incorporated TiO2 microspheres: Facile flame assisted hydrolysis of tetrabutyl orthotitanate and photocatalytic hydrogen production

We report a novel and facile energy-saving method to prepare microspherical carbon-incorporated titania powders by flame assisted hydrolysis of tetrabutyl orthotitanate. The as-prepared samples were fully characterized by XRD, SEM, XPS, UV-Vis absorption spectra and photocatalytic hydrogen production. Anatase TiO₂ can be obtained directly without any post heat treatment. The as-prepared TiO₂ is formed of microspheres with sizes in a range of 0.5∼2.0 μm. XPS measurement shows the presence of carbon species which come from the incomplete combustion of organic compounds. Enhanced photocatalytic hydrogen production rates were observed for the as-prepared samples. A maximum hydrogen production rate was 8.1 μmol h⁻¹, which was 1.8 times larger than that of Degussa P25. The improved photocatalytic activity is attributed to enhanced light absorption behavior, which is caused by carbon incorporation and microspherical structure. This work demonstrates a novel and efficient strategy to synthesize microspherical anatase TiO₂ photocatalyst without any special equipment or setup.     

Ultrasonic spray pyrolysis synthesis of Ag/TiO2 nanocomposite photocatalysts for simultaneous H2 production and CO2 reduction

Simultaneous photocatalytic hydrogen production and CO₂ reduction (to form CO and CH₄) from water using methanol as a hole scavenger were investigated using silver-modified TiO₂ (Ag/TiO₂) nanocomposite catalysts. A simple ultrasonic spray pyrolysis (SP) method was used to prepare mesoporous Ag/TiO₂ composite particles using TiO₂ (P25) and AgNO₃ as the precursors. The material properties and photocatalytic activities were compared with those prepared by a conventional wet-impregnation (WI) method. It was found that the samples prepared by the SP method had a larger specific surface area and a better dispersion of Ag nanoparticles on TiO₂ than those prepared by the WI method, and as a result, the SP samples showed much higher photocatalytic activities toward H₂ production and CO₂ reduction. The optimal Ag concentration on TiO₂ was found to be 2 wt%. The H₂ production rate of the 2% Ag/TiO₂–SP sample exhibited a six-fold enhancement compared with the 2% Ag/TiO₂–WI sample and a sixty-fold enhancement compared with bare TiO₂. The molar ratio of H₂ and CO in the final products can be tuned in the range from 2 to 10 by varying the reaction gas composition, suggesting a viable way of producing syngas (a mixture of H₂ and CO) from CO₂ and water using the prepared Ag/TiO₂ catalysts with energy input from the sun.     

Enhanced hydrogen generation from methanol aqueous solutions over Pt/MoO3/TiO2 under ultraviolet light

The photocatalytic activity in hydrogen production from methanol reforming can be significantly enhanced by Pt/MoO₃/TiO₂ photocatalysts. Compared with Pt/P25, the photocatalytic activity of optimized Pt/MoO₃/TiO₂ shows an evolution rate of 169 μmol/h/g of hydrogen, which is almost two times higher than that of Pt/P25. XRD and Raman spectra show that MoO₃ are formed on the surface of TiO₂. It is found that with the bulk MoO₃ just formed, the catalyst shows the highest activity due to a large amount of heterojunctions and the high crystallinity of MoO₃. The HRTEM image showed a close contact between MoO₃ and TiO₂. It is proposed that the Z-scheme type of heterojunction between MoO₃ and TiO₂ is responsible for the improved photocatalytic activity. The heterojunction structure of MoO₃/TiO₂ does not only promote the charge separation, but also separates the reaction sites, where the oxidation (mainly on MoO₃) and reduction (on TiO₂) reactions occurred.     

Silver/titania nanocomposite-modified photoelectrodes for photoelectrocatalytic methanol oxidation

Silver deposited titania (Ag/TiO₂) nanocomposite thin films were fabricated by the simple sonochemical deposition of Ag on preformed aerosol-assisted chemical vapor deposited TiO₂ thin films. The photelectrocatalytic performance of a newly fabricated Ag/TiO₂-modified photoelectrode was studied for methanol oxidation under simulated solar AM 1.5G irradiation (100 mW/cm²). The Ag/TiO₂-modified photoelectrode showed a photocurrent density of 1 mA/cm², which is four times that of an unmodified TiO₂ photoelectrode. The modification of Ag on the TiO₂ surface significantly enhanced the photoelectrocatalytic performance by improving the interfacial charge transfer processes, which minimized the charge recombination. Density functional theory (DFT) calculation studies revealed that methanol could be easily adsorbed onto the Ag surfaces of Ag/TiO₂ via a partial electron transfer from Ag to methanol. The newly fabricated Ag/TiO₂-modified photoelectrode could be a promising candidate for photoelectrochemical applications.     

Effective water splitting using N-doped TiO2 films: Role of preferred orientation on hydrogen production

N-doped TiO₂ film with preferred (211) orientation, deposited by RF magnetron sputtering, was investigated for the water-splitting hydrogen production. It is found that the preferred crystal growth orientation of the films can be controlled by N₂ flow rate during the deposition. The results reveal that not only the N-doping, but also the preferred orientation (i.e., large percentage of exposed (211) facet), can effectively enhance the activity of TiO₂-based photocatalyst. With the increase of exposed (211) facets, the hydrogen production rates of N-doped TiO₂ films rise from 760 μmol H₂ h⁻¹ m⁻² to 4500 μmol H₂ h⁻¹ m⁻², indicating that high performance of TiO₂-based photocatalyst can be achieved by controlling the preferred orientation of the films.     

Optical properties of TiO2 thin films deposited by DC sputtering and their photocatalytic performance in photoinduced process

TiO₂ thin films were deposited by DC Sputtering varying the deposit time. These films were characterized by XRD, AFM, photoluminescence, UV–Vis, ellipsometry and XPS. The optical properties of TiO₂ thin films with different thickness, influenced their photocatalytic behavior in two photoinduced process. When TiO₂ thin films were irradiated with a UV light, midgap states were generated and the electrons were placed in lower energies than its band gap, favoring the photocatalytic hydrogen production and CO₂ photoreduction. From PL technique analyses it was observed that electrons occupied midgap states between the bands, with lower energies than the band gap. With these results it was possible to propose an energy diagram in order to correlate with photoinduced processes results. The presence of Ti³⁺ species was reconfirmed by means of XPS analyses. These species could be found in the midgap states, generated by the interaction between the UV irradiation and the film surface, which contributed to the photocatalytic activity of the films. The hydrogen production was similar for all the thin films studied (33–35 μmol) associated to the presence of similar energy midgap states. In the case of CO₂ photoreduction, all films produced CH₂O (8951 and 6252 μmol/g) and the films with a thickness of 330 and 420 nm generated CH₃OH (970 and 292 μmol/g). The extinction coefficient confirmed the XRD results for the film with greatest deposited time, which exhibited the highest crystallinity. All photocatalytic results did not show any dependence with the thin film thickness.     

Hydrogen generation from photocatalytic water splitting over TiO2 thin film prepared by electron beam-induced deposition

Photocatalytic TiO₂ thin films were prepared via an electron beam-induced deposition (EBID) method. The effects of post-calcination treatment on the properties of the prepared TiO₂ thin films were studied. X-ray diffraction (XRD), scanning electron microscope-energy dispersive spectrometry (SEM-EDS), and UV–V is absorption spectrometry were performed to reveal the crystallinity, surface morphology, chemical composition, and light absorbance of the prepared TiO₂ thin films. The photoelectrochemical characteristics of the TiO₂ thin films were investigated with a potentiostat. Under UV irradiation, a photocurrent of ˜2.1 mA was observed for the TiO₂ thin film with post-calcination at 500 °C. A water-splitting reaction was conducted over the TiO₂ thin film with the best photoelectrochemical performance. The yields of hydrogen and oxygen were 59.8 and 30.6 μmole, respectively, after 8 h of reaction under UV irradiation.     

Hydrogen gas sensing based on polyaniline/anatase titania nanocomposite

Polyaniline (emeraldine)/anatase TiO₂ nanocomposite (PA-NC) was prepared by a chemical oxidative polymerization. The thin films of PA-NC for hydrogen gas sensing application were deposited on Cu-interdigited electrodes by spin coating technique. A study on characteristics of PA-NC thin films was demonstrated by a porous cylindrical morphology. The response and response/recovery time of sensors for hydrogen gas were evaluated by the change of TiO₂ wt% at environmental conditions. Resistance-sensing measurement was exhibited a high sensitivity about 1.63, a good Long-term response, low response time and recovery time about 83 s and 130 s, respectively, at 0.8 vol% hydrogen gas for PA-NC including 25% wt of anatase nanoparticles. The current–voltage characteristics of PA-NC gas sensors before and after hydrogen gas injection showed a nonlinear ohmic current. Moreover, we studied the formation of PA-NCs and their hydrogen gas sensing mechanism based on contact regions in PA-NC.