Direct probing of solvent-induced charge degradation in polypropylene electret fibres via electrostatic force microscopy

Electrostatic force microscopy was used to directly probe solvent‐induced charge degradation in electret filter media. Electrostatic force gradient images of individual polypropylene electret fibres were used to quantify the extent of charge degradation caused by the immersion of the fibres into isopropanol. Electrostatic force gradient images were obtained by monitoring the shifts in phase and frequency between the oscillations of the biased atomic force microscopy (AFM) cantilever and those of the piezoelectric driver. Electrostatic force microscopy measurements were performed using non‐contact scans at a constant tip‐sample separation of 75 nm with varied bias voltages applied to the cantilever. Mathematical expressions, based on the capacitance of the tip‐sample system, were used to model the phase and frequency shifts as functions of the applied bias voltage to the tip and the offset voltage due to the fibre's charge. Quantitative agreement between the experimental data and the simplified model was observed.     

Analysis of dynamic cantilever behavior in tapping mode atomic force microscopy

Tapping mode atomic force microscopy (AFM) provides phase images in addition to height and amplitude images. Although the behavior of tapping mode AFM has been investigated using mathematical modeling, comprehensive understanding of the behavior of tapping mode AFM still poses a significant challenge to the AFM community, involving issues such as the correct interpretation of the phase images. In this paper, the cantilever's dynamic behavior in tapping mode AFM is studied through a three dimensional finite element method. The cantilever's dynamic displacement responses are firstly obtained via simulation under different tip‐sample separations, and for different tip‐sample interaction forces, such as elastic force, adhesion force, viscosity force, and the van der Waals force, which correspond to the cantilever's action upon various different representative computer‐generated test samples. Simulated results show that the dynamic cantilever displacement response can be divided into three zones: a free vibration zone, a transition zone, and a contact vibration zone. Phase trajectory, phase shift, transition time, pseudo stable amplitude, and frequency changes are then analyzed from the dynamic displacement responses that are obtained. Finally, experiments are carried out on a real AFM system to support the findings of the simulations. Microsc. Res. Tech. 78:935–946, 2015. © 2015 Wiley Periodicals, Inc.     

High-resolution constant-height imaging with apertured silicon cantilever probes

We present high-resolution aperture probes based on non-contact silicon atomic force microscopy (AFM) cantilevers for simultaneous AFM and near-infrared scanning near-field optical microscopy (SNOM). For use in near-field optical microscopy, conventional AFM cantilevers are modified by covering their tip side with an opaque aluminium layer. To fabricate an aperture, this metal layer is opened at the end of the polyhedral probe using focused ion beams (FIB). Here we show that apertures of less than 50 nm can be obtained using this technique, which actually yield a resolution of about 50 nm, corresponding to λ/20 at the wavelength used. To exclude artefacts induced by distance control, we work in constant-height mode. Our attention is particularly focused on the distance dependence of resolution and to the influence of slight cantilever bending on the optical images when scanning at such low scan heights, where first small attractive forces exerted on the cantilever become detectable.     

Non-optical tip–sample distance control method for scanning near-field optical microscopy using a piezoresistive micro cantilever

A piezoresistive micro cantilever is applied to monitor the displacement of an optical fibre probe and to control tip–sample distance. The piezoresistive cantilever was originally made for a self-sensitive atomic force microscopy (AFM) probe and has dimensions of 400 µm length, 50 µm width and 5 µm thickness with a resistive strain sensor at the bottom of the cantilever. We attach the piezoresistive cantilever tip to the upper side of a vibrating bent optical fibre probe and monitor the resistance change amplitude of the strain sensor caused by the optical fibre displacement. By using this resistance change to control the tip–sample distance, the two-cantilever system successfully provides topographic and near-field optical images of standard samples in a scanning near-field optical microscopy (SNOM)/AFM system. A resonant characteristic of the two-cantilever system is also simulated using a mechanical model, and the results of simulation correspond to the experimental results of resonance characteristics.     

Finite-element vibration analysis of tapping-mode atomic force microscopy in liquid

Investigation of morphology and mechanical properties of biological specimens using atomic force microscopy (AFM) often requires its operation in liquid environment. Due to the hydrodynamic force, the vibration of AFM cantilevers in liquid shows dramatically different dynamic characteristics from that in air. A good understanding of the dynamics of AFM cantilevers vibrating in liquid is needed for the interpretation of scanning images, selection of AFM operating conditions, and evaluation of sample's mechanical properties. In this study, a finite element (FE) model is used for frequency and transient response analysis of AFM cantilevers in tapping mode (TM) operated in air or liquid. Hydrodynamic force exerted by the fluid on AFM cantilevers is approximated by additional mass and hydrodynamic damping. The additional mass and hydrodynamic damping matrices corresponding to beam elements are derived. With this model, numerical simulations are performed for an AFM cantilever to obtain the frequency and transient responses of the cantilever in air and liquid. The comparison between our simulated results and the experimentally obtained ones shows good agreement. Based on the simulations, different characteristics of cantilever dynamics in air and liquid are discussed.     

Dual resonance excitation system for the contact mode of atomic force microscopy

We propose an improved system that enables simultaneous excitation and measurements of at least two resonance frequency spectra of a vibrating atomic force microscopy (AFM) cantilever. With the dual resonance excitation system it is not only possible to excite the cantilever vibrations in different frequency ranges but also to control the excitation amplitude for the individual modes. This system can be used to excite the resonance frequencies of a cantilever that is either free of the tip-sample interactions or engaged in contact with the sample surface. The atomic force acoustic microscopy and principally similar methods utilize resonance frequencies of the AFM cantilever vibrating while in contact with the sample surface to determine its local elastic modulus. As such calculation demands values of at least two resonance frequencies, two or three subsequent measurements of the contact resonance spectra are necessary. Our approach shortens the measurement time by a factor of two and limits the influence of the AFM tip wear on the values of the tip-sample contact stiffness. In addition, it allows for in situ observation of processes transpiring within the AFM tip or the sample during non-elastic interaction, such as tip fracture.     

Combined atomic force and scanning reflection interference contrast microscopy

A sphere attached to a cantilever is used simultaneously as an atomic force microscope (AFM) tip and as a curved reflective surface for producing scanning reflection interference contrast microscope (RICM) images of fluorescent beads dried onto a glass slide. The AFM and RICM images are acquired in direct registration which enables the identification of individually excited beads in the AFM images. The addition of a sharp, electron beam-deposited tip to the sphere gives nanometer resolution AFM images without loss of optical contrast.     

Suppression of spurious vibration of cantilever in atomic force microscopy by enhancement of bending rigidity of cantilever chip substrate

To improve the precision of dynamic atomic force microscopy (AFM) using cantilever vibration spectra, a simple but effective method for suppressing spurious response (SR) was developed. The dominant origin of SR was identified to be the bending vibration of the cantilever substrate, by the analysis of the frequency of SR. Although a rigid cover pressing the whole surface of the substrate suppressed SR, the utility was insufficient. Then, a method of enhancing the bending rigidity of the substrate by gluing a rigid plate (clamping plate, CP) to the substrate was developed. This chip can be used with an ordinary cantilever holder, so that the reproducibility of SR suppression when attaching and detaching the cantilever chip to the holder was improved. To verify its utility, the evaluation of a microdevice electrode was performed by ultrasonic atomic force microscopy. The delamination at a submicron depth was visualized and the detailed variation of the delamination was evaluated for the first time using clear resonance spectra. The CP method will particularly contribute to improving dynamic-mode AFM, in which resonance spectra with a low quality factor are used, such as noncontact mode AFM in liquid or contact resonance mode AFM. The effect of the CP can be achieved by fabricating a substrate with a thick plate beforehand.     

MAC mode atomic force microscopy studies of living samples, ranging from cells to fresh tissue

Magnetic AC mode (MAC mode) atomic force microscopy (AFM), a novel type of tapping mode AFM in which the cantilever is driven directly by a magnetic field, is a powerful tool for imaging with high spatial resolution and better signal-to-noise in liquid environment. It may largely extend the application of AFM to living samples, especially those are sensitive to cantilever forces, even to multilayer tissue samples. However, there are few reports on the imaging of living cells by MAC mode AFM previously. In our present study, we explore the optimal imaging conditions of MAC mode AFM on living astrocytes and fresh arterial intima surface. We also used nude tips for PicoTREC panel (i.e., Aux in BNC, a new data collecting channel) to image living samples and discussed its difference with phase imaging. We show that living biological samples can be imaged by MAC mode AFM at details of comparable resolution as those by high resolution scanning electron microscopy. Furthermore, the combination of height, amplitude, phase and TREC panel signals provide abundant informations for the characteristics of living samples, such as topography, profile, stiffness and adhesion.     

Scanning electron microscopy studies of protein-functionalized atomic force microscopy cantilever tips

Protein-functionalized atomic force microscopy (AFM) tips have been used to investigate the interaction of individual ligand-receptor complexes. Herein we present results from scanning electron microscopy (SEM) studies of protein-functionalized AFM cantilever tips. The goals of this study were (1) to examine the surface morphology of protein-coated AFM tips and (2) to determine the stability of the coated tips. Based on SEM images, we found that bovine serum albumin (BSA) in solution spontaneously adsorbed onto the surface of silicon nitride cantilevers, forming a uniform protein layer over the surface. Additional protein layers deposited over the initial BSA-coated surface did not significantly alter the surface morphology. However, we found that avidin-functionalized tips were contaminated with debris after a series of force measurements with biotinylated agarose beads. The bound debris presumably originated from the transfer of material from the agarose bead. This observation is consistent with the observed deterioration of functional activity as measured in ligand-receptor binding force experiments.     

Investigation of influence of gas atmosphere and pressure upon non-contact atomic force microscopy

Resonance measurements and atomic force microscopy (AFM) observations were carried out by the non-contact AFM operating in various gas atmospheres (hydrogen, helium, nitrogen and argon) over the range of pressures from 0.1 to 1.1 MPa. In each atmosphere, the resonance frequency of the AFM cantilever depended on the pressure of gases studied. The plots of the relative resonance frequency at a constant pressure vs. the gas density gave a straight line. It was found that the characteristic of the resonance frequency for the AFM cantilever were dependent on the density of the gas species. The resolution of the AFM was hardly influenced by the gas atmosphere under the present experimental conditions.     

Second harmonic atomic force microscopy imaging of live and fixed mammalian cells

Higher harmonic contributions in the movement of an oscillating atomic force microscopy (AFM) cantilever are generated by nonlinear tip–sample interactions, yielding additional information on structure and physical properties such as sample stiffness. Higher harmonic amplitudes are strongly enhanced in liquid compared to the operation in air, and were previously reported to result in better structural resolution in highly organized lattices of proteins in bacterial S-layers and viral capsids [J. Preiner, J. Tang, V. Pastushenko, P. Hinterdorfer, Phys. Rev. Lett. 99 (2007) 046102]. We compared first and second harmonics AFM imaging of live and fixed human lung epithelial cells, and microvascular endothelial cells from mouse myocardium (MyEnd). Phase–distance cycles revealed that the second harmonic phase is 8 times more sensitive than the first harmonic phase with respect to variations in the distance between cantilever and sample surface. Frequency spectra were acquired at different positions on living and fixed cells with second harmonic amplitude values correlating with the sample stiffness. We conclude that variations in sample stiffness and corresponding changes in the cantilever–sample distance, latter effect caused by the finite feedback response, result in second harmonic images with improved contrast and information that is not attainable in the fundamental frequency of an oscillating cantilever.     

Influence of Poisson's ratio variation on lateral spring constant of atomic force microscopy cantilevers

Atomic force microscopy (AFM) can be used to measure the surface morphologies and the mechanical properties of nanostructures. The force acting on the AFM cantilever can be obtained by multiplying the spring constant of AFM cantilever and the corresponding deformation. To improve the accuracy of force experiments, the spring constant of AFM cantilever must be calibrated carefully. Many methods, such as theoretical equations, the finite element method, and the use of reference cantilever, were reported to obtain the spring constant of AFM cantilevers. For the cantilever made of single crystal, the Poisson's ratio varies with different cantilever-crystal angles. In this paper, the influences of Poisson's ratio variation on the lateral spring constant and axial spring constant of rectangular and V-shaped AFM cantilevers, with different tilt angles and normal forces, were investigated by the finite element analysis. When the cantilever's tilt angle is 20 degrees and the Poisson's ratio varies from 0.02 to 0.4, the finite element results show that the lateral spring constants decrease 11.75% for the rectangular cantilever with 1muN landing force and decrease 18.60% for the V-shaped cantilever with 50nN landing force, respectively. The influence of Poisson's ratio variation on axial spring constant is less than 3% for both rectangular and V-shaped cantilevers. As the tilt angle increases, the axial spring constants for rectangular and V-shaped cantilevers decrease substantially. The results obtained can be used to improve the accuracy of the lateral force measurement when using atomic force microscopy.     

Improving tapping mode atomic force microscopy with piezoelectric cantilevers

This article summarizes improvements to the speed, simplicity and versatility of tapping mode atomic force microscopy (AFM). Improvements are enabled by a piezoelectric microcantilever with a sharp silicon tip and a thin, low-stress zinc oxide (ZnO) film to both actuate and sense deflection. First, we demonstrate self-sensing tapping mode without laser detection. Similar previous work has been limited by unoptimized probe tips, cantilever thicknesses, and stress in the piezoelectric films. Tests indicate self-sensing amplitude resolution is as good or better than optical detection, with double the sensitivity, using the same type of cantilever. Second, we demonstrate self-oscillating tapping mode AFM. The cantilever's integrated piezoelectric film serves as the frequency-determining component of an oscillator circuit. The circuit oscillates the cantilever near its resonant frequency by applying positive feedback to the film. We present images and force-distance curves using both self-sensing and self-oscillating techniques. Finally, high-speed tapping mode imaging in liquid, where electric components of the cantilever require insulation, is demonstrated. Three cantilever coating schemes are tested. The insulated microactuator is used to simultaneously vibrate and actuate the cantilever over topographical features. Preliminary images in water and saline are presented, including one taken at 75.5 μm/s—a threefold improvement in bandwidth versus conventional piezotube actuators.     

Prototype cantilevers for quantitative lateral force microscopy

Prototype cantilevers are presented that enable quantitative surface force measurements using contact-mode atomic force microscopy (AFM). The "hammerhead" cantilevers facilitate precise optical lever system calibrations for cantilever flexure and torsion, enabling quantifiable adhesion measurements and friction measurements by lateral force microscopy (LFM). Critically, a single hammerhead cantilever of known flexural stiffness and probe length dimension can be used to perform both a system calibration as well as surface force measurements in situ, which greatly increases force measurement precision and accuracy. During LFM calibration mode, a hammerhead cantilever allows an optical lever "torque sensitivity" to be generated for the quantification of LFM friction forces. Precise calibrations were performed on two different AFM instruments, in which torque sensitivity values were specified with sub-percent relative uncertainty. To examine the potential for accurate lateral force measurements using the prototype cantilevers, finite element analysis predicted measurement errors of a few percent or less, which could be reduced via refinement of calibration methodology or cantilever design. The cantilevers are compatible with commercial AFM instrumentation and can be used for other AFM techniques such as contact imaging and dynamic mode measurements.     

Variable-force tapping atomic force microscopy as a tool in the characterization of organic devices

A common method for characterizing the phase separation of materials in mixtures is tapping mode atomic force microscopy (AFM). However, AFM results are influenced by surface-energy effects and the employed tapping force, and it might therefore be difficult to attain correct information regarding the bulk with such a surface-imaging technique. In this work, we present a way of imaging material phase separation in an improved manner by recording a series of AFM images at different tapping force. More specifically, we have employed the variable-force AFM method on organic mixtures, comprising a conjugated polymer (MEH-PPV) and an ion-conducting polymer electrolyte (PEO-XCF(3)SO(3), X=Li, K, Rb), and we demonstrate that it is capable of reversibly sampling such materials not only on the surface, but also (indirectly) in the topmost part of the bulk. The analysis of the evolution of AFM phase images allows us to (indirectly) gain information about the bulk-phase separation of materials. We find that the variable-force AFM results correlate well with the device performance of light-emitting electrochemical cells employing such organic mixtures as the active material.     

Molecular dynamics simulation of the contact process in AFM surface observations

In the present work, several molecular dynamics simulations have been performed to clarify dynamically the contact mechanism between the specimen surface and probe tip in surface observations by an atomic force microscope (SFM) or friction force microscope (FFM). In the simulation, a three‐dimensional model is proposed where the specimen and the probe are assumed to consist of monocrystalline copper and rigid diamond or a carbon atom, respectively. The effect of the cantilever stiffness of the AFM/FFM is also taken into consideration. The surface observation process is simulated on a well‐defined Cu{100} surface. From the simulation results it has been verified that the surface images and the two‐dimensional atomic‐scale stick‐slip phenomenon, just as is the case for real AFM/FFM surface observations, can be detected from the spring force acting on the cantilever. From the evaluation of the behaviour of specimen surface atoms, the importance of the specimen stiffness in deciding the cantilever properties can also be understood. The influence of the probe tip shape on the force images is also evaluated. From the results it can be verified that the behaviour of the specimen surface atoms as well as the solid surface images in AFM/FFM surface observations can be understood using the molecular dynamics simulation of the model presented.     

Development of a microlateral force sensor and its evaluation using lateral force microscopy

A microlateral force sensor (MLFS) was developed and evaluated using atomic force microscopy (AFM). The sensor was attached to a sensing table supported by a suspension system. The lateral motion of the sensing table was activated by a comb actuator. The driving voltage to the comb actuator was controlled to maintain a constant position of the sensing table by detecting the tunneling current at a detector, which consisted of two electrodes where the bias voltage was applied. An AFM was used to apply a lateral force to the sensing table of the sensor. When the probe of a cantilever was pressed against the sensing table and a raster scanning was conducted, the driving voltage of the comb actuator changed to compensate the friction force between the probe and sensing table. AFM measurements of an asperity array on the sensing table were conducted, and a lateral force microscopy image (LFM) was obtained from the change in driving voltage. The image by MLFS was very similar to the LFM image that was conventionally obtained from torsion of the cantilever. The LFM image strongly correlated with the gradient image calculated from the AFM topographic image. The force sensitivity of the MLFS was determined by comparing the LFM image obtained by using the MLFS with the tangential force derived from the gradient of the AFM image.     

Study of the tip mass and interaction force effects on the frequency response and mode shapes of the AFM cantilever

The vibrational characteristics of an atomic force microscope (AFM) cantilever beam play a key role in dynamic mode of the atomic force microscope. As the oscillating AFM cantilever tip approaches the sample, the tip–sample interaction force influences the cantilever dynamics. In this paper, we present a detailed theoretical analysis of the frequency response and mode shape behavior of a cantilever beam in the dynamic mode subject to changes in the tip mass and the interaction regime between the AFM cantilever system and the sample. We consider a distributed parameter model for AFM and use Euler–Bernoulli method to derive an expression for AFM characteristics equation contains tip mass and interaction force terms. We study the frequency response of AFM cantilever under variations of interaction force between AFM tip and sample. Also, we investigate the effect of tip mass on the frequency response and also the quality factor and spring constant of each eigenmodes of AFM micro-cantilever. In addition, the mode shape analysis of AFM cantilever under variations of tip mass and interaction force is investigated. This will incorporate the presentation of explicit analytical expressions and numerical analysis. The results show that by considering the tip mass, the resonance frequencies of the cantilever are decreased. Also, the tip mass has a significant effect on the mode shape of the higher eigenmodes of the AFM cantilever. Moreover, tip mass affects the quality factor and spring constant of each modes.     

Observation of HOPG by STM and contact AFM in various gas atmospheres under pressures up to 1.1 MPa

Apparatus comprising a scanning tunneling microscopy (STM) and an atomic force microscopy (AFM) has been developed for use under supra-atmospheres. Observations of highly oriented pyrolytic graphite (HOPG) were carried out by STM and contact AFM operating in air and various gas atmospheres (hydrogen, helium, neon and argon) under pressures up to 1.1 MPa. Atomic resolution images of the HOPG were obtained by STM in all the gas atmospheres studied. However, it was found that the presence of water vapor gave rise to a noise current at increased pressures. Using contact AFM, the atomic resolution in an argon atmosphere decreased with increasing pressure, while atomic images were obtained under the other gas atmospheres at 1.1 MPa.