Behaviour of a full-scale expanded bed reactor with overlaid anaerobic and aerobic zones for domestic wastewater treatment.

This paper presents the behaviour of a full-scale expanded bed reactor (160 m3) with overlaid anaerobic and aerobic zones used for municipal wastewater treatment. The research was carried out in two experimental steps: anaerobic and anaerobic-aerobic conditions, and the experimental results presented in this paper refer to four months of reactor operation. In the anaerobic condition, after inoculation and 60 days of operation, the reactor treating 3.40 kg CODm(-3)d(-1) for thetaH of 2.69 h, reached mean removal efficiencies of 76% for BOD, 72% for COD, and 80% for TSS, when the effluent presented mean values of 225 mg.L(-1) of COD, 98 mg.L(-1) of BOD and 35 mg.L(-1) of TSS. Under these conditions, for nitrogen loading of 0.27 kgN.m(-3)d(-1), the reactor generated an effluent with mean N-org. of 8 mg.L(-1) and N-ammon. of 37 mg.L(-1), demonstrating high potential of ammonification. For the anaerobic-aerobic condition (118th day) the system was operated with thetaH of 5.38 h presented mean removal efficiencies of 84% for BOD, 79% for COD, 76% for TSS, and 30% for TKN. The reactor's operation time was less than two months, which was not long enough to reach nitrification. Regarding the obtained results, this research confirmed that this reactor is configured as a flexible and adequate alternative for the treatment of sewage, requiring relatively small area and only thetaH of 10 h that can be adjusted to the local circumstances.     

High-rate wastewater treatment combining a moving bed biofilm reactor and enhanced particle separation.

Many cities around the world are looking for compact wastewater treatment alternatives since space for treatment plants is becoming scarce. In this paper development of a new compact, high-rate treatment concept with results from experiments in lab-scale and pilot-scale are presented. The idea behind the treatment concept is that coagulation/floc separation may be used to separate suspended and colloidal matter (resulting in > 70% organic matter removal in normal wastewater) while a high-rate biofilm process (based on Moving Bed biofilm reactors) may be used for removing low molecular weight, easily biodegradable, soluble organic matter. By using flotation for floc/biomass separation, the total residence time for a plant according to this concept will normally be < 1 hour. A cationic polymer combined with iron is used as coagulant at low dosages (i.e. 1-2 mg polymer/l, 5-10 mg Fe/l) resulting in low sludge production (compared to conventional chemical treatment) and sufficient P-removal.     

改进型移动床生物膜反应器处理有机废水的试验

改进型移动床生物膜反应器(CMCBR)是在普通移动床生物膜反应器中引入导流板,使填料在全池循环移动,消除了普通移动床生物膜反应器的死角。在CMCBR处理模拟生活污水的试验中,研究了有机物的去除效果,考察了容积负荷、水力停留时间、冲击负荷等参数对处理效果的影响。试验发现,在填料填充比例为50%(体积比),进水COD质量浓度为320~550mg/L,水力停留时间为3 h的条件下,出水COD质量浓度小于100 mg/L,达到国家污水综合排放标准的一级标准。反应器具有较强的抗冲击负荷能力,出水水质稳定。     

内循环生物流化床处理N、P废水的试验研究

采用内循环生物流化床系统,进行N、P废水的试验研究,通过控制曝气时间和溶解氧浓度,能同时达到脱氮除磷的效果.对于N、P废水,COD在352～1048 mg/L,TN在46.9～76.4 mg/L,TP在5.8～14.4 mg/L时,COD、TN、TP去除率分别为92%、80%、93%,处理后的水可达到国家二级排放标准.     

厌氧颗粒污泥悬浮床反应器的研究与应用

提出厌氧复合循环颗粒污泥悬浮床反应器的新型反应器理论.通过引入分级三相分离器,使悬浮床反应器上部处理区液体和沼气的上升速度大大降低,创造了污泥颗粒沉降的良好环境.底部利用高负荷产生的沼气形成内循环,同时设置外回流系统,内、外循环实现了进水与颗粒污泥间的充分接触及保持了良好的反应条件,创造了大幅度提高CODCr容积负荷的条件.对反应器的启动、运行和在不同负荷条件下的去除效果和悬浮流态进行了研究.研究表明,厌氧颗粒污泥悬浮床反应器处理淀粉废水,可在负荷30～40 kg CODCr/(m3·d)条件下稳定运行,最高负荷达57.2kgCODCr/(m3·d),平均CODCr去除率可达90%.     

Enhanced biological wastewater treatment using sodium alginate-immobilized microorganisms in a fluidized bed reactor

In this study, a microbial consortium isolated from an activated sludge tank of a conventional wastewater treatment plant was immobilized using sodium alginate (SA) as a support material for contaminant biodegradation in wastewater. A volume of 500 mL of activated sludge was immobilized in the SA beads (with a mass concentration of 25 g/L). The resulting SA beads were characterized, introduced into a fluidized bed reactor, fed with 1000 mL of the sample, and characterized again after the treatment process. The SA-immobilized microorganisms were tested first for degradation of organic matter (expressed as chemical oxygen demand) and total phosphorous in domestic wastewater, achieving removal efficiencies of 71% and 93%, respectively, after 12 h. Subsequently, the SA-immobilized microorganisms were tested for degradation of a basic blue 9 (BB9) textile dye in a condition that simulated textile wastewater. The efficiency of the BB9 degradation was found to be as high as 99.5% after 2 h. According to these results, SA-immobilized microorganisms were found to be an environmentally friendly and cost-effective alternative for treatment of municipal and industrial wastewater effluents.     

Tracking particle size distributions in a moving bed biofilm membrane reactor for treatment of municipal wastewater.

A study has been conducted to investigate the effect of loading rates on membrane fouling in a moving bed biofilm membrane reactor process for municipal wastewater treatment, especially analysing the fate of submicron colloidal particles and their influence on membrane fouling. Two operating conditions defined as low and high organic loading rates were tested where the development and fate of the particulate material was characterised analysing the particle size distributions throughout the process. Analysis of the membrane performance showed higher fouling rates for the high-rate conditions. The fraction of colloidal submicron particles was higher in the membrane reactor indicating that fouling by these particles was a dominant contribution to membrane fouling.     

Treatment of winery wastewater in a full-scale fixed bed biofilm reactor.

The treatment of winery wastewater was performed at full-scale applying a two-stage fixed bed biofilm reactor (FBBR) system for the discharge in the sewerage. The results of the first year of operation at the full-scale plant are presented. Values of removed organic loads and effluent concentrations were interpreted on the basis of the COD fractionation of influent wastewater assessed through respirometric tests. The average removal efficiency of total COD was 91 %. It was not possible to reach an higher efficiency because of the unbiodegradable soluble fraction of COD (about 10% of total COD on average during the whole year), that cannot be removed by biological process or settling. Due to the high empty space offered by the plastic carriers, FBBRs did not require backwashing during the seasonal operationing period of the plant (September-March). In comparison with other treatment systems the FBBR configuration allows one to ensure a simple management, to obtain high efficiency also in the case of higher fluctuations of flow and loads and to guarantee a good settleability of the sludge, without bulking problems.     

Simultaneous removal of carbon and nitrogen in an anaerobic inverse fluidized bed reactor.

The evaluation of simultaneous removal of carbon and nitrogen in an anaerobic inverse fluidized bed reactor is described. Continuous and batch experiments were used, with synthetic wastewater and glucose as the carbon source with two different nitrate concentrations of 100 and 250 mg N-NO3/L. The evolution of substrates and the concentrations of intermediary products in the gas phase were followed. Results indicate that the use of the biofilm in the inverse fluidized bed reactor allows the expression of denitrification and methanization activities simultaneously without physical or time separation. The removal of nitrogen with both the feeding of 100 and 250 mgN-NO3/L was higher than 90%, while the removal of carbon was 65% on average for the feeding with 100 mgN-NO3/L and 70% on average for the feeding with 250 mg N-NO3/L. This carbon degradation is equivalent to that obtained during the operation of the reactor in the period previous to the nitrate feeding. It was found that by using high values of the COD/N ratio, the dissimilative reduction of nitrates is favoured. Denitrification and anaerobic digestion occurs simultaneously under low values of COD/N.     

Innovations in wastewater treatment: the moving bed biofilm process.

This paper describes the moving bed biofilm reactor (MBBR) and presents applications of wastewater treatment processes in which this reactor is used. The MBBR processes have been extensively used for BOD/COD-removal, as well as for nitrification and denitrification in municipal and industrial wastewater treatment. This paper focuses on the municipal applications. The most frequent process combinations are presented and discussed. Basic design data obtained through research, as well as data from practical operation of various plants, are presented. It is demonstrated that the MBBR may be used in an extremely compact high-rate process (<1 h total HRT) for secondary treatment. Most European plants require P-removal and performance data from plants combining MBBR and chemical precipitation is presented. Likewise, data from plants in Italy and Switzerland that are implementing nitrification in addition to secondary treatment are presented. The results from three Norwegian plants that are using the so-called combined denitrification MBBR process are discussed. Nitrification rates as high as 1.2 g NH4-N/m2 d at complete nitrification were demonstrated in practical operation at low temperatures (11 degrees C), while denitrification rates were as high as 3.5g NO3-Nequiv./m2.d. Depending on the extent of pretreatment, the total HRT of the MBBR for N-removal will be in the range of 3 to 5 h.     

Phenolic refinery wastewater biodegradation by an expanded granular sludge bed reactor.

Refinery spent caustics (SC) were diluted with sour waters (SW) in a ratio 1:7, neutralized with CO2 (SC/SW(CO2)) and 83% of H2S was striped during this procedure, remaining an aromatic portion that contained 2123, 2730 and 1379 mg L(-1) of phenol, p-cresol and o-cresol, respectively. The mixture was teated anaerobically in an EGSB reactor fed with 1.5 gCOD L(-1) d(-1), without mineral supplements causing loss of COD removal efficiency that dropped to 23%, methane production ceased and no phenol or cresols were biodegraded. The EGSB experiments were resumed by feeding the reactor with nutrients and phenol at 1.0 gCOD L(-1) d(-1). The mixture SC/SWco2 added to the phenol load, was step increased from 0.10 to 0.87 gCODL(-1) d(-1) maximum. When total organic load was increased to 1.6, COD removal efficiency was 90% and at the highest load attained, 1.87, efficiency dropped to 23% attributed to the toxic effect produced by cresols.     

新型废水厌氧处理工艺——内循环厌氧反应器

介绍内循环(IC)厌氧反应器的发展、基本结构、运行机理。分析该反应器的工艺过程,指出该工艺具有处理效率高、抗冲击能力强等优点。针对IC反应器存在的缺陷,人们对该反应器进行技术改进:通过提高它的内循环的气量进行处理低浓度有机废水;增加外循环装置缩短IC反应器的启动周期。     

Influence of effluent-recirculation condition on the process performance of expanded granular sludge bed reactor for treating low strength wastewater.

A 2.0 L volume of EGSB reactor was operated at 20 degrees C for more than 500 days with 0.3-0.4 g COD/L of sucrose base wastewater to investigate the influence of effluent-recirculation on the process performance. At the start up period, the reactor was operated in EGSB mode with 5 m/h upflow velocity by continuous effluent recirculation. The COD loading was set to 7.2-9.6 kg COD/m(3) day with HRT of 1 hour. However, in this mode, EGSB reactor exhibited insufficient COD removal efficiency, i.e., 50-60%. Therefore, UASB mode (without recirculation, 0.7 m/h upflow velocity) was used for 30 minutes in every 40 minutes cycle to increase the COD concentration in the sludge bed. As a result, an excellent process performance was shown. The COD removal efficiency increased from 65% to 91% and the reactor could maintain a good physical property of retained sludge (sludge concentration: 33.4 g VSS/L and SVI: 25 mL/g VSS). Furthermore, retained sludge possessed sufficient level of methanogenic activity at 20 degrees C.     

Biological sludge solubilisation for reduction of excess sludge production in wastewater treatment process.

A novel sludge disintegration system (JFE-SD system) was developed for the reduction of excess sludge production in wastewater treatment plants. Chemical and biological treatments were applied to disintegrate excess sludge. At the first step, to enhance biological disintegration, the sludge was pretreated with alkali. At the second step, the sludge was disintegrated by biological treatment. Many kinds of sludge degrading microorganisms integrated the sludge. The efficiency of the new sludge disintegration system was confirmed in a full-scale experiment. The JFE-SD system reduced excess sludge production by approximately 50% during the experimental period. The quality of effluent was kept at quite a good level. Economic analysis revealed that this system could significantly decrease the excess sludge treatment cost.     

Effect of temperature and salinity on the wastewater treatment performance of aerobic submerged fixed bed biofilm reactors.

The influence of temperature (5-35 C) and salinity (up to 20 g/l NaCl) on the wastewater purification process in completely mixed and aerated submerged fixed bed biofilm reactors (SFBBRs) was studied. C- and N-conversion in SFBBRs designed according to the DWA (German Association for Water, Wastewater and Waste) rules for carbon removal was investigated for several months on synthetic wastewater. The DOC degradation rate was even at, according to the DWA, high DOC/BOD loading rates not much affected by temperatures between 5-35 degrees C and salt contents up to 20 g/L NaCl. At these high DOC loadings an appreciable ammonium conversion could also be observed. The ammonium conversion proved to be sensitive to temperature and salinity. At 5 degrees C the ammonium removal rate decreased by a factor of five compared to 25-35 degrees C. Under many operation conditions investigated more than 50% of the converted ammonium was transformed into gaseous nitrogen. The addition of 20 g/L NaCl caused a strong inhibition of the ammonium removal rate over the whole temperature range investigated.     

Intermittent vs continuous operation of upflow anaerobic sludge bed reactors for dairy wastewater and related microbial changes.

This work compares continuous vs intermittent UASB reactors inoculated with flocculent sludge for the treatment of dairy effluents. The effects of effluent recirculation on the performance of intermittent reactors were assessed as well as the differences in specific methanogenic activity (SMA) with different substrates for the biomass from continuous and intermittent UASB reactors. Compared to the continuous operation the intermittent operation resulted in higher methanization of the removed COD (64-78% and 65-88%, respectively) whilst the effluent recirculation presented beneficial effects when applied during the stabilization period and was clearly detrimental when applied during the feed period of the intermittent operation. The SMA tests showed that the intermittent operation causes a shift in the microbial populations towards a better adaptation for the degradation of complex substrates confirmed by the meaningfull contribution of methane production through a pathway other than acetoclastic methanogenesis observed in the biomass taken from intermittent UASB reactors.     

Anaerobic biodegradation of 2,4,6-trichlorophenol in expanded granular sludge bed and fluidized bed biofilm reactors bioaugmented with Desulfitobacterium spp

The biodegradation of 2,4,6-trichlorophenol (246TCP) was studied using expanded granular sludge bed (EGSB) reactors and a fluidized bed biofilm reactor (FBBR) filled with activated carbon. One of the EGSB reactor and the FBBR were bioaugmented with Desulfitobacterium strains. 246TCP loading rate was gradually incremented from 10 to 250 mg L(-1) day(-1). The main pathway of dechlorination was in ortho-position, generating 4-chlorophenol and 2,4-dichlorophenol. The maintenance of both COD degradation efficiency (higher than 80%) and methanogenic efficiency (between 0.3 and 0.6 g CH4-COD g(-1) COD consumed) in EGSB reactor implies a great stability of the process. Through isotherm studies in FBBR, it could be deduced that around 52% of 246TCP was completely dechlorinated, whereas the adsorption involved around 16%. By means of FISH studies it was proved that the methanogenic Archaea community was maintained in the bioaugmented EGSB reactor, whereas in the FBBR this community was gradually developed until reaching stability. Desulfitobacterium community was also maintained in the reactors, although D. chlororespirans proportion rise in the FBBR at the higher 246TCP loading rates, implying that this species can withstand the 246TCP toxicity better than D. hafniense.     

Biological granulated activated carbon fluidized bed reactor for atrazine remediation.

To show that an adsorbing biofilm carrier (GAC) can be advantageous for atrazine bioremediation over a non-adsorbing carrier, fluidized bed (FB) reactors were operated under atrazine limiting concentrations using Pseudomonas sp. strain ADP as the atrazine degrading bacteria. The following interrelated subjects were investigated: 1) atrazine adsorption to GAC under conditions of atrazine partial penetration in the biofilm, 2) differences in atrazine degradation rates and 3) stability of atrazine biodegradation under non-sterile anoxic conditions in the GAC reactor versus a reactor with a non-adsorbing biofilm carrier. Results from batch adsorption tests together with modeling best described the biofilm as patchy in nature with covered and non-biofilm covered areas. Under conditions of atrazine partial penetration in the biofilm, atrazine adsorption occurs in the non-covered areas and is consequently desorbed at the base of the biofilm substantially increasing the active biofilm surface area. The double flux of atrazine to the biofilm in the GAC reactor results in lower effluent atrazine concentrations as compared to a FB reactor with a non-adsorbing carrier. Moreover, under non-sterile denitrification conditions, atrazine degradation stability was found to be much higher (several months) using GAC as a biofilm carrier while non-adsorbing carrier reactors showed sharp deterioration within 30 days due to contamination of non-atrazine degrading bacteria.     

Anaerobic treatment of vinasses by a sequentially mixed moving bed biofilm reactor.

Wine distillery wastewater, commonly called vinasses, was treated by an anaerobic moving bed biofilm reactor (AMBBR) with 32.9 litre available volume. The reactor was filled with 66% cylindrical polyethylene supports with density 0.84 g cm(-3) as a biofilm carrier. The reactor was sequentially mixed by a submerged centrifugal pump fixed to the bottom, and each mixing time just lasted 1.25 minutes. The organic loading rate (OLR) of the reactor were increased from 1.6 to 29.6 g sCOD l(-1) d(-1) (soluble chemical oxygen demands--sCOD) and hydraulic retention time (HRT) was decreased from 6.33 to 1.55 days accordingly. Soluble COD removal efficiency was 81.3-89.2% at an OLR of 29.6 g sCOD l(-1) d(-1). At the end of the experiment, 83.4% total biomass was attached on support and the specific density of support in the reactor was 0.93-1.05 g cm(-3), which increased by about 10.7-25% compared with that at the beginning of the study.