Adsorption of heavy metal ions from aqueous solution by fly ash

The removal characteristics of lead and copper ions from aqueous solution by fly ash were investigated under various conditions of contact time, pH and temperature. The influence of pH of the metal ion solutions on the uptake levels of the metal ions by fly ash were carried out between pH 4 and 12. The level of uptake of Pb²⁺ and Cu²⁺ ions by the fly ash generally increased, but not in a progressive manner, at higher pH values. The effect of temperature on the uptake of Pb²⁺ and Cu²⁺ ions was investigated between 30 °C and 60 °C, the adsorption of being enhanced at the lowest temperature. Rate constants were evaluated in terms of a first-order kinetics. The rate constant, k for uptake of Pb²⁺ and Cu²⁺ ions were 1.77 × 10⁻² s⁻¹ and 2.11 × 10⁻² s⁻¹, respectively. The experimental results underline the potential of coal fly ash for the recovery of metal ions from waste water. The main mechanisms involved in the removal of heavy metal ions from solution were adsorption at the surface of the fly ash and precipitation.     

含金属离子赖氨酸水溶液的萃取分离

采用二(2-乙基己基)磷酸(P204)作萃取剂,航空煤油作稀释剂,对含有钙、镁、钠、钾等金属离子的赖氨酸水溶液进行萃取,以蒸馏水作为反萃取剂对有机相进行反萃取分离实验.结果表明,原料液初始pH值在4～5、P204与煤油体积比为3:2、有机相与水相比为2:1、反应萃取时间大于30min、搅拌转速约200rpm时,能够取得较好的萃取效果.以初始pH值≥3.5的蒸馏水为反萃取剂,蒸馏水与有机相体积比4:1,在150rpm的转速下搅拌20min能够较为完全地分离出赖氨酸,然后在其它条件相同的情况下,用初始pH＜1的蒸馏水对有机相再次反萃取可分离出金属离子,从而实现萃取剂的重复利用.     

Removal of metal ions from aqueous solution by activated carbons obtained from different raw materials

The adsorption of Pb²⁺, Cu²⁺, Zn²⁺ and Cd²⁺ from aqueous solution at 293 K by activated carbons obtained from different raw materials was studied. These carbons were prepared by water vapour pyrolysis of the raw materials—apricot stones, coconut shells and lignite coal. The influence of the solution pH on the adsorption processes has been studied. The presence of other metal ions in the solution decreases the adsorption of each of the ions. The selective adsorption of the metal ions is observed but the ones preferentially adsorbed do not completely prevent the adsorption of other ions. The chemical nature of the carbon surface and metal ions have great significance for the adsorption process.     

高效去除水溶液中重金属离子的氧化石墨烯基材料的综述

综述了氧化石墨烯(graphene oxide,GO)基纳米材料对水溶液中各种重金属离子的优异去除能力的最新研究成果。重点论述了吸附剂的合成,吸附过程特征及相互作用机理,概述了各种环境条件的影响。综述旨在为设计和制造GO基纳米材料提供有用的信息,以消除环境污染管理中废水中的重金属离子。此外,简要概述,并提出了这一鼓舞人心的领域所面临的挑战和前景。     

Calixarene-based extractants for heavy metal ions removal from aqueous solutions

The article reviews the literature on the possibility of application of the calixarene-based compounds for selective separation of toxic heavy metals from aqueous solutions by the solvent extraction and transport across liquid membranes. The specific three-dimensional structure of calixarenes and their derivatives, simple and low-cost synthesis, and ease of chemical transformation qualify these compounds for the role of selective chemical extractants of toxic heavy metal ions present in industrial wastewater. This article analyses the influence of various process factors, with the greatest emphasis on the structure of the extractants/carriers, on efficient separation of heavy metal ions, primarily those most commonly found in galvanic wastewater.     

Application of a carbon sorbent for the removal of cadmium and other heavy metal ions from aqueous solution

Treatment of flax shive with sulfuric acid produces a carbonaceous material that has been used to remove metal ions from aqueous solution. Metal ions including Cd(II), Cu(II), Cr(III), Co(II), Ni(II), Zn(II) and Pb(II) have been investigated for kinetic behaviour and sorption capacities. These metal ions show fast sorption kinetics following a first order rate equation. Cadmium was chosen as representative of these metal ions and a detailed study was carried out. The effect of pH on sorption was studied and it was found that maximum uptake occurred above pH 3–7, sorption was accompanied by release of protons into the solution and a ratio of [H⁺] released to [Cd²⁺] sorbed of approximately 2 was found. The sorption capacity showed no significant increase with increase of temperature. The presence of other metal ions such as K⁺, Na⁺, Mg²⁺ and Ca²⁺ decreases the Cd(II) capacity, indicating competition for the ion exchange sites. Successive sorption of Cd(II) shows that the capacity exceeds the monolayer capacity calculated from the Langmuir equation. Column studies showed good performance over a total of seven cycles of loading/stripping. These studies indicate that the sorption mechanism for these metal ions is related to a reversible ion exchange process on the carbon surface. © 2002 Society of Chemical Industry     

Adsorption characteristics of sericite for cesium ions from an aqueous solution

To efficiently remove cesium ions from aqueous solution, sericite was used as a novel adsorbent. The silanol (SiO₂) and aluminol (Al₂O₃) groups in sericite are likely to play an important role in adsorption process. The maximum adsorption capacity (q_m) and adsorption constant (K_L) for cesium ions obtained from the Langmuir isotherm model were 6.68 mg/g and 0.227 L/mg, respectively and regression curve fit well with the experimental data as the 0.965 of correlation coefficients (r²). However, when the Freundlich isotherm model was used correlation coefficient (r²) was 0.973. Therefore, it was concluded that Freundlich model fits equilibrium data better than Langmuir model. When the 6.0 g/L of sericie concentration was added to aqueous solution, cesium ions were removed by about 80% and the increase was not happened above 6.0 g/L of sericite concentration any more. The process was determined as exothermic reaction because the removal efficiency of cesium ions decreased as temperature increased. Furthermore, all adsorption was completed in 120 min and comparing the pseudo first and second-order kinetic models indicates that the adsorption of cesium ions using sericite follows well the pseudo-second-order kinetics.     

Selective removal of some heavy metal ions from aqueous solution using treated polyethylene-g-styrene/maleic anhydride membranes

Radiation graft copolymerization of styrene/maleic anhydride (Sty/MAn) comonomer onto low density polyethylene (LDPE) membrane was investigated. The prepared grafted membranes were treated with different reagents containing various functional groups and studied as a matrix for the purpose of water purification from heavy metals. The metal ion uptake by the functional groups of membranes was determined by the use of X-ray fluorescence (XRF) and atomic absorption (AA). The effect of pH of the metal feed solution and immersion period needed for maximum capacity was investigated. The selectivity of different prepared membranes towards some selected metal ions such as Fe, Cu, Pb,… etc. which commonly exist in waste water was determined. The affinity of the treated grafted films to recover Fe(III), Cu(II) or Pb(II) from their aqueous solutions containing other metal ions such as Cd(II), Ni(II) or Hg(II) was studied. Also the selectivity of treated grafted membranes towards Cu(II), Cr(III) and Fe(III) in a mixture was investigated at room temperature and 70°C. It was found that the thiosemicarbazide-, hydroxylamine·HCl- and NaOH-treated grafted films showed high selectivity towards Cu(II), Cr(III) and Fe(III), respectively, at 70°C. However, the selectivity of such treated grafted membranes was remarkable towards Fe(III) at room temperature. The results obtained suggested that the treated grafted membrane possessed good chelating properties towards different metal ions. This suggests that such membranes could be accepted for practical uses.     

Removal of yttrium ions from aqueous solution by ion flotation

Conditions for the concentration of yttrium from aqueous solution by ion flotation using α-sulphonated fatty acids were studied. The effects of change of collector and colligend concentration and pH, as well as the effect of interfering ions, were investigated. Maximum recovery was 99·5%.     

Removal of toxic metal ions from aqueous systems by biosorptive flotation

Biosorptive flotation was used as a combined operation for the simultaneous abstraction of nickel, copper and zinc ions from aqueous streams. Laboratory‐scale batch experiments, as well as pilot‐scale continuous experiments, have been conducted. Grape stalks, a by‐product of the winery industry, were used as sorbent material. The experimental procedure consisted of two consecutive stages: (i) biosorption, and (ii) flotation. The possibility of reusing biomass, after appropriate elution, was also examined. The main parameters examined were biomass concentration, particle size of sorbent, surfactant concentration, pH and flocculation. Flotation removals, following laboratory‐scale experiments, were found to be in the order of 100, 85 and 70% for copper, zinc and nickel, respectively. In pilot‐scale experiments, biomass sorption capacities were determined as 25 for copper, 81 for zinc and 7 µmol dm^?3 for nickel. The order of biomass affinity regarding the studied metals was Cu > Zn > Ni. Short retention time and high effectiveness suggest that biosorptive flotation is a promising treatment process for the removal of toxic metals from contaminated aqueous solutions. © 2002 Society of Chemical Industry     

Zeolite synthesis from coal fly ash for the removal of lead ions from aqueous solution

Fly ash samples from the Bayswater and Eraring power plants, located in New South Wales, Australia, were used in a preliminary study on zeolite synthesis by hydrothermal treatment with sodium hydroxide under various conditions. The treated fly ash was tested for the ability to remove lead ions from aqueous solution. Both fly ashes were partially converted to zeolite. The zeolites formed under the experimental conditions were zeolite Na‐P1 and sodalite octahydrate for the Bayswater ash and phillipsite, zeolite X, zeolite Na‐P1 and sodalite octahydrate for the Eraring ash. The type of zeolite formed was dependent on the treatment time and sodium hydroxide concentration. In the case of the Bayswater ash, zeolite Na‐P1 was formed by treatment with 4 mol dm^?3 NaOH for 48 h while treatment with 5 mol dm^?3 NaOH for 96 h produced sodalite octahydrate at the expense of zeolite Na‐P1. In the case of the Eraring ash, phillipsite was formed following treatment with 3 mol dm^?3 NaOH, zeolite X and zeolite Na‐P1 were formed following treatment with 4 mol dm^?3 NaOH and sodalite octahydrate was formed following treatment with 5 mol dm^?3 NaOH. A maximum cation exchange capacity of ～400 meq/100 g was achieved by both treated ash samples. Treatment of a solution with a lead ion concentration of 120 ppm using 0.5 g of both treated ash samples (S/L ratio = 0.25 g/100 cm³) achieved complete removal in 5 min, whereas treatment with 0.1 g of each material (S/L ratio = 0.05 g/100 cm³) achieved complete lead ion removal after 24 h. © 2001 Society of Chemical Industry     

Preparation of amidoximated polyester fiber and competitive adsorption of some heavy metal ions from aqueous solution onto this fiber

In this study, a fibrous adsorbent containing amidoxime groups was prepared by graft copolymerization of acrylonitrile (AN) onto poly(ethylene terephthalate) (PET) fibers using benzoyl peroxide (Bz₂O₂) as initiator in aqueous solution, and subsequent chemical modification of cyano groups by reaction with hydroxylamine hydrochloride in methanol. The grafted and modified fibers were characterized by FTIR, TGA, SEM, and XRD analysis. The crystallinity increased, but thermal stability decreased with grafting and amidoximation. The removal of Cu(II), Ni(II), Co(II), Pb(II), and Cd(II) ions from aqueous solution onto chelating fibers were studied using batch adsorption method. These properties were investigated under competitive conditions. The effects of the pH, contact time, and initial ion concentration on the removal percentage of ions were studied. The results show that the adsorption rate of metal ions followed the given order Co(II) > Pb(II) > Cd(II) > Ni(II) > Cu(II). The percentage removal of ions increased with initial ion concentration, shaking time, and pH of the medium. Total metal ion removal capacity was 49.75 mg/g fiber on amidoximated fiber. It was observed that amidoximated fibers can be regenerated by acid without losing their activity, and it is more selective for Pb(II) ions in the mixed solution of Pb‐Cu‐Ni–Co‐Cd at pH 4. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Removal of metal ions from aqueous solution by adsorption onto activated carbon cloths: adsorption competition with organic matter

Activated carbon cloths are recent adsorbents whose adsorption properties are well known for monocomponent solutions of organics or metal ions. However, to treat wastewaters with these materials, their performance has to be determined in multicomponent solution. This work studies adsorption competition between metal ions (Cu²⁺, Pb²⁺) and organic matter (benzoic acid). The first part investigates adsorption equilibrium of monocomponent metal ions solutions and shows the dependence of adsorption capacities on adsorbent porosity and metal ions chemical properties (molecular weight, ionic radius and electronegativity). The influence of pH is also demonstrated. The second part focuses on adsorption competition: (1) between both metal ions (a decrease of adsorption capacities is observed, whose value is related to adsorption kinetics of metal ions); (2) between metal ions and organic matter, in solution or adsorbed onto the activated carbon cloth (a strong influence of pH is shown: when benzoic acid is under benzoate form, in both cases adsorption is increased due to the formation of ligands between adsorbed benzoate ions and metals).     

New sorbent hydrogels for removal of acidic dyes and metal ions from aqueous solutions

Summary Poly(N-hydroxymethylacrylamide), PHMA, hydrogels were prepared by using N-hydroxymethylacrylamide, HMA, monomer and polyethyleneglycol(400)diacrylate as a crosslinking agent in aqueous medium and then amine groups were incorporated onto PHMA hydrogels by amination reaction with different diamines. The obtained hydrogels were characterized by determination of amine value, hydroxymethyl group content and FTIR spectra. The amine value of hydrogels changed from 2.23 to 4.64 mmol/g by depending on the amine compounds used in amination reaction. Their swelling degree increased at acidic pH values and they showed pH dependent swelling behaviour. They were used as sorbent for removal of indigo carmine and Cu(II) ion, as a model dye molecule and metal ion, respectively, from aqueous solutions. The adsorption properties of the hydrogels were investigated by depending on pH, time and initial indigo carmine or Cu(II) ion concentration. It was seen that the amine group incorporated hydrogels have quite high adsorption rate and adsorption capacity, and their adsorption capacities changed with pH of the solution. Langmuir isotherm model was the best fit for adsorption of both indigo carmine and Cu (II) ion.     

Production of hydroxyapatite-based adsorbent for the removal of cobalt ions from the aqueous solution

The aim of the current study was to recover and separate cobalt ions from multielement solution, using hydroxyapatite (HAp) and magnetic nanocomposite of HAp/Fe₃O₄ as adsorbents. Cobalt ion adsorption process was conducted batchwise within the temperature 25˗55°C, exposure duration 5˗120 min by applying a dose of 0.25–5 g/L as the adsorbent at pH 2 to 9.  Adsorbent characterization was performed using advanced spectroscopic techniques such as Fourier Transform Infrared Spectroscopy, Scanning electron microscopy, and Energy-dispersive X-ray spectroscopy. The maximum ionic adsorption efficiency using HAp was 90.48% against 94.72% in the case of the magnetic nanocomposite of HAp, under optimal conditions. Various isotherm models were used to evaluate the adsorption capacity and equilibrium coefficients for adsorption of the cobalt ions by the prepared adsorbents. The isotherm models data showed that the adsorption process is desirable by the adsorbents and by adding nanoparticles of Fe₃O₄ the adsorption capacity improves.     

Removal of heavy metal ions from aqueous solution by multi-walled carbon nanotubes modified with 8-hydroxyquinoline: Kinetic study

Carbon nanotubes were modified with 8-hydroxyquinoline and used for the removal of Cu(II), Pb(II), Cd(II), and Zn(II) from aqueous solutions. Different instrumentation parameters and methods of development for determining metal ions from aqueous solutions using differential pulse anodic stripping voltammetry were studied. The adsorption of heavy metals from aqueous solution by the pristine and modified MWCNTs was studied kinetically using different kinetic models, and the results showed that the adsorption process best fitted the pseudo-second-order model and the Elovich model. The mechanism of adsorption was explored using the intra-particle diffusion model and the liquid-film model.     

曲霉对水中重金属的吸附去除

利用两种曲霉 ( A.sojae M1 46和 A.oryzae M1 49)的菌体作为吸附剂 ,对水中 Pb( )和 Cd( )进行去除实验。结果表明 :曲霉菌体的最佳培养时间为 72 h;吸附的最佳 p H为 5.5、温度为 3 0℃、时间为 1 h。在最佳实验条件下 :A.sojae M1 46对 Pb( )和 Cd( )的吸附率分别为 69.76%和 72 .2 8% ;A.oryzae M1 49对 Pb( )和 Cd( )的吸附率分别为 60 .64 %和 81 .3 4%。使用稀碱溶液对曲霉菌体进行浸泡预处理后提高了对重金属的吸附去除效果 ;而使用稀酸、乙醇水溶液以及蒸馏水对菌体浸泡后明显降低了重金属的去除效果。Na2 CO3和 EDTA溶液可以有效地将重金属从曲霉菌体上解吸下来 ,从而达到重复利用菌体作为吸附剂的目的。     

Removal of metal ions from electrochemical decontamination solution using organic acids

Applicability of the organic acids and cyclodextrin (CD) for the removal of Fe, Co and Ni from the spent electro-decontamination solution was investigated. Oxalic acid showed the highest removal efficiency: 90% for 0.89 M Fe and 95% for 0.0089 M Co and Ni, respectively. The metal–oxalate precipitates were characterized by differential scanning calorimetry/thermogravimetry analysis (DSC/TGA), Fourier transform infrared (FTIR) and X-ray fluorescence (XRF). After thermal decomposition at >300°C, the metal–oxalate precipitates were transformed into metal oxides (Fe₂O₃, FeO, CoO and NiO) and pure metals (Co and Ni). The results imply that organic acids have a high potential for the removal of heavy metals from electro-decontamination solutions.     

Adsorption of heavy metal ions from aqueous solutions by porous polyacrylonitrile beads

The adsorption of Cu(II), Ni(II), Zn(II), and Pb(II) from aqueous solutions on acrylonitrile copolymer sorbents was studied. We prepared five types of sorbents from polyacrylonitrile by varying its concentration in the initial polymer solution and the composition of the coagulation bath, aiming to achieve a different porous structure. The specific area, pore volume, and pore radius of the sorbents were determined on a porosimeter. The porous structure was studied by scanning electron microscopy. Modification of sorbents with sodium hydroxide and hydroxylamine was carried out to form amidooxyme and carboxylic groups with proven complex‐forming properties toward heavy metal ions. The optimal pH of the sorption of metal ions was found. The adsorption kinetics were investigated. The order of polymer sorbents toward the sorption of Pb(II), Cu(II), Ni(II), and Zn(II) ions, and the order of heavy metal uptake were determined for all types of sorbents. The effectiveness of heavy metal desorption and the coefficient of recovery of sorption ability were determined. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 83: 3036–3044, 2002; DOI 10.1002/app.2334