Nondestructive testing for crack of tunnel lining using GPR

Lining craze, as a common engineering damage, affects the bearing capacity and the safety of tunnels.To improve the capabilities of the surface crack detection in the tunnel lining, ground penetrating radar(GPR) was employed. The principle and method of GPR for cracks investigation of tunnel lining were expounded. As an application example, some field measurements in order to detect the depth of cracks for the tunnel lining were achieved in a new tunnel. All GPR investigations were made with the antennae of 1 GHz. The cracks of concrete structure were located, and the distributing and depth of cracks are inspected and estimated by GPR. The results of investigation show GPR is accurate and efficient to detect cracks of tunnel lining.     

Relationship between subsurface damage and surface roughness of ground optical materials

A theoretical model of relationship between subsurface damage and surface roughness was established to realize rapid and non-destructive measurement of subsurface damage of ground optical materials.Postulated condition of the model was that subsurface damage depth and peak-to-valley surface roughness are equal to depth of radial and lateral cracks in brittle surface induced by small-radius(radius≤200 μm)spherical indenter,respectively.And contribution of elastic stress field to the radial cracks propagation was also considered in the loading cycle.Subsurface damage depth of ground BK7 glasses was measured by magnetorheological finishing spot technique to validate theoretical ratio of subsurface damage to surface roughness.The results show that the ratio is directly proportional to load of abrasive grains and hardness of optical materials,while inversely proportional to granularity of abrasive grains and fracture toughness of optical materials.Moreover,the influence of the load and fracture toughness on the ratio is more significant than the granularity and hardness,respectively.The measured ratios of 80 grit and 120 grit fixed abrasive grinding of BK7 glasses are 5.8 and 5.4,respectively.     

Mechanism of zonal disintegration phenomenon in enclosing rock mass around deep tunnels

In order to study the mechanism of the zonal disintegration phenomenon (ZDP), both experimental and theoretical investigations were carried out. Firstly, based on the similarity law, gypsum was chosen as equivalent material to simulate the deep rock mass, the excavation of deep tunnel was modeled by drilling a hole in the gypsum models, two circular cracked zones were measured in the model, and ZDP in the enclosing rock mass around deep tunnel was simulated in 3D gypsum model tests. Secondly, based on the elasto-plastic analysis of the stressed-strained state of the surrounding rock mass with the improved Hoek-Brown strength criterion and the bilinear constitutive model, the maximum stress zone occurred in vicinity of the elastic-plastic interface due to the excavation of the deep tunnel, rock material in maximum stress zone is in the approximate uniaxial loading state owing to the larger tangential force and smaller radial force, the mechanism of ZDP was explained, which lay in the creep instability failure of rock mass due to the development of plastic zone and transfer of the maximum stress zone within the rock mass. Thirdly, the analytical critical depth for the occurrence of ZDP was obtained, which depended on the mechanical indices and stress concentration coefficient of rock mass. Foundation item: Projects(50525825, 90815010) supported by the National Natural Science Foundation of China; Project(2009CB724608) supported by the Major state Basic Research Development Program of China     

Dynamic services selection algorithm in Web services composition supporting cross-enterprises collaboration

Based on the deficiency of time convergence and variability of Web services selection for services composition supporting cross-enterprises collaboration, an algorithm QCDSS (QoS constraints of dynamic Web services selection) to resolve dynamic Web services selection with QoS global optimal path, was proposed. The essence of the algorithm was that the problem of dynamic Web services selection with QoS global optimal path was transformed into a multi-objective services composition optimization problem with QoS constraints. The operations of the cross and mutation in genetic algorithm were brought into PSOA (particle swarm optimization algorithm), forming an improved algorithm (IPSOA) to solve the QoS global optimal problem. Theoretical analysis and experimental results indicate that the algorithm can better satisfy the time convergence requirement for Web services composition supporting cross-enterprises collaboration than the traditional algorithms. Foundation item: Project(70631004) supported by the Key Project of the National Natural Science Foundation of China; Project(20080440988) supported by the Postdoctoral Science Foundation of China; Project(09JJ4030) supported by the Natural Science Foundation of Hunan Province, China; Project supported by the Postdoctoral Science Foundation of Central South University, China     

Remanufacturing strategy for chemical equipment

Failure, especially induced by cracks, usually occurred in the service process of chemical equipment, which could cause the medium leakage, fire hazard and explosion and induced the personnel casualty and economic losses. To assure the long-term and safety service, it is necessary to apply the remanufacturing technology on the chemical equipment containing cracks. The recent research advances on the remanufacturing, the failure modes and the life extension technology for chemical equipment were reviewed. The engineering strategy of the remanufacturing for the chemical equipment was proposed, which could provide a reasonable and reliable technical route for the remanufacturing operation of chemical equipment. In the strategy, the redesign was also been considered. Foundation item: Project (50235030) supported by the National Natural Science Foundation of China     

Synthesis and photophysical and electrochemical properties of new cyclometalated platinum complex containing oxadiazole ligand

A new cyclometalated platinum complex containing 2, 5-bis（naphthalene-1-yl）-1,3,4-oxadiazole ligand was synthesized and characterized. The UV-Vis absorptions and photoluminescent properties of the ligand and its platinum complex were investigated A characteristic metal-ligand charge transfer absorption peak at 439 nm in the UV spectrum and a strong emission peak at 625 nm in the photoluminescence spectrum were observed for this complex in dichloromethane. Cyclic voltammtry （CV） analysis shows that the EHOMO （energy level of the highest occupied molecular orbital） and ELUMO （energy level of the lowest unoccupied molecular orbital） of the platinum complex are about -5.69 and -3.25 eV, respectively, indicating that the oxadiazole-based platinum complex has a potential application in electrophosphorescent devices used as a red-emitting material.     

Delay-independent decentralized H ∞ control for multi-channel discrete-time systems with uncertainties

A robust decentralized H∞ control problem was considered for uncertain multi-channel discrete-time systems with time-delay. The uncertainties were assumed to be time-invariant, norm-bounded, and exist in the system, the time-delay and the output matrices. Dynamic output feedback was focused on. A sufficient condition for the multi-channel uncertain discrete time-delay system to be robustly stabilizable with a specified disturbance attenuation level was derived based on the theorem of Lyapunov stability theory. By setting the Lyapunov matrix as block diagonal appropriately according to the desired order of the controller, the problem was reduced to a linear matrix inequality （LMI） which is sufficient to existence condition but much more tractable. An example was given to show the efficiency of this method.     

Modeling and simulation of crushing process of spiral mining head

1 INTRODUCTIONThe research of mining deep seabed cobalt-richcrust is a hotspot of international oceanology[1].Based on the mining manganese nodule ,lots of re-searches on mining cobalt crust have been madedeeply and many kinds of methods ,such as thei m-proved CLB, mining vehicle +lifting system +surface supporting ship have been put forward.Mining vehicle consists of collecting machine ,tracked treading machine and spiral mininghead[2 ,3].The first step of mining cobalt crust is tocrush…     

Four optimal design approaches of high-order finite-impulse response filters based on neural network

Four optimal approaches of high-order finite-impulse response(FIR) digital filters were developed for designing four types filters using neural network algorithms. The solutions were presented as parallel algorithms to approximate the desired frequency response specification. Therefore, these methods avoid matrix inversion, and make a fast calculation of the filter’s coefficients possible. The convergence theorems of these proposed algorithms were presented and proved to illustrate them stable, and the implementation of these methods was described together with some design guidelines. The simulation results show that the ripples of the designed FIR filters are significantly little in the pass-band and stop-band, and the proposed algorithms are of fast convergence.     

Analysis and calculation of thermal conductivity of rock in deep strata

The thermal conductivity of rock is an important parameter for the deep mine and the geothermal development. It is often not possible to measure the thermal conductivity of the rocks present in the deep strata, and the usual approach is to calculate thermal conductivity including mineralogy and porosity. The compositions of core samples from the MID01 borehole in the Bj?rk? area were determined, and the minera composition was classified. The calculation of the thermal conductivity of rock in the borehole was carried out, and the main factors for the thermal conductivity of rock were analyzed. The results show that the calculated thermal conductivity of rock is reliable and useful for the design and calculation of geothermal development in the Bj?rk? area. Foundation item: Project(50490274) supported by the National Natural Science Foundation of China; project supported by the Postdoctoral Science Foundation of China and Bj?rk? project supported by the Energy Agency of Sweden     

Fatigue properties of 48MnV steel with twin arc spraying 3Cr13 coatings

The fatigue behaviors of 48MnV steel, both uncoated and coated with different thicknesses of 3Cr13 deposits using twin arc spraying, were investigated. The fatigue properties of the 48MnV steel, determined under axial loading conditions, can be substantially decreased by coating 3Cr13 films, deposited by twin arc spraying. And the fatigue behavior of the thinner coatings is better than that of the thicker ones, of which the fatigue limits decrease by 9%–14%. The decrease in fatigue life attributes to the less mechanical properties of the coatings in comparison with those of the substrate, their relative bad bonding strength and trapped oxide or Al₂O₃ particles retain in the matrix after blasting responsible for the initiation of fatigue cracks. Foundation item: Project (50235030) supported by the National Natural Science Foundation of China     

Feasibility study of marrow stromal cells transplantation into guinea pig cochlea

Objective This pilot-study was designed to evaluate the feasibility of cell transplantation into guinea pig cochlea. Methods Marrow stromal cells were labeled with DAPI, and then implanted into the cochlea of guinea pig. The existence and differentiation trend were observed roughly two weeks later by histologic analysis. Results Transplant-derived marrow stem cells survived in cochlea two weeks later with a trend of attaching to cochlear architecture but not differentiate into neuron. Conclusions Transplant-derived marrow stem cells can survive in cochlea, and cell transplantation may be a useful strategy in inner ear diseases. Foundation item: Project (30000094) supported by the National Nature Science Foundation of China; project supported by the Postdoctoral Foundation of Central South University     

Residual stresses within sprayed coatings

Some important developments of residual stress researches for coating-based systems were studied. The following topics were included the sources of residual stresses in coatings: error analysis of Stoney’s equation in the curvature method used for the measurement of coating residual stress, the modeling of residual stress and some analytical models for predicting the residual stresses in coatings. These topics should provide some important insights for the fail-safe design of the coating-based systems. Foundation item: Project(50235030) supported by the National Natural Science Foundation of China; Project(2003AA331130) supported by the National High-Tech Research and Development Program of China     

基于GprMax的隧道衬砌地质雷达检测正演模拟与实测数据分析

利用时间域有限差分（FDTD）软件GprMax,根据初衬中钢拱架和钢筋的电磁参数,建立不同模型,模拟地质雷达对隧道衬砌的检测过程。由于隧道衬砌、围岩、钢筋等各种工程介质的介电常数存在不同的差异,使得不同目标在雷达图像上显示出不同特性的波形特征。结果表明：钢拱架雷达图像明显,反射回波显著,波形特征为分散的月牙形强反射信号,无明显多次反射波;钢筋的波形为向上凸起的弧形,且交织在一起。将这一结果与实例探测结果进行对比。对比实际探测结果表明：二衬内有钢筋分布的情况下,不可能在二衬之后准确检测出初衬内的钢拱架的数量及分布情况,所以初衬检测与二衬检测应分开进行;利用软件GprMax模拟地质雷达在初衬中的检测是准确可行的,能够清晰地反映隧道衬砌中钢拱架和钢筋的成像特征,效果较好,可为工程实践判别提供依据。     

A bi-objective model for job-shop scheduling problem to minimize both energy consumption and makespan

The issue of reducing energy consumption for the job-shop scheduling problem in machining systems is addressed, whose dual objectives are to minimize both the energy consumption and the makespan. First, the biobjective model for the job-shop scheduling problem is proposed. The objective function value of the model represents synthesized optimization of energy consumption and makespan. Then, a heuristic algorithm is developed to locate the optimal or near optimal solutions of the model based on the Tabu search mechanism. Finally, the experimental case is presented to demonstrate the effectiveness of the proposed model and the algorithm. Foundation item: Project (50475062) supported by the National Natural Science Foundation of China; project (2004-47-19) supported by the Natural Science Foundation of Chongqing City of China     

Synthesis and optophysical properties of blue-emitting iridium （Ⅲ） complex bearing oxadiazole-based picolinic acid derivative

An iridium (III) bis[(4,6-difluorophenyl)pyridinato-N, C²][6-(6′-(4″-(5‴-phenyl-1‴, 3‴, 4‴-oxadiazole- 2‴-yl) phenoxy) hexyloxy picolinate) was synthesized and characterized by ¹H NMR and elementary analysis in order to study the effect of ancillary ligand of the oxadiazole-based picolinic acid derivative on optophysical properties of its iridium complex, and further to obtain an iridium complex with highly-efficient blue emission. The thermal stability, UV absorption and photoluminescent properties of this iridium complex were investigated. Compared with iridium (III) bis[(4,6-difluorophenyl)pyridinato-N, C²](picolinate) reported as a highly-efficient blue electroluminescent material, this iridium complex bearing an oxadiazole-based picolinic acid derivative presents higher thermal stability, more intense UV absorption at 291 nm and similar photoluminescent spectrum peaked at 469 nm. This indicates that tuning ancillary ligand of picolinic acid with an oxadiazole unit can improve the optophysical properties of its iridium complex. Foundation item: Projects(20772101, 50473046) supported by the National Natural Science Foundation of China; Project(2007FJ3017) supported by the Hunan Provincial Science Foundation, China; Project(07C764) supported by the Science Foundation of the Education Department of Hunan Province, China     

Directly searching method for slip plane and its influential factors based on critical state of slope

In order to determine the slip plane of slope directly by the calculation results of strength reduction method, and analyze the influential factors of slope stability, a numerical model was established in plane strain mode by FLAC3D for homogeneous soil slope, whose parameters were reduced until the slope reached the critical state. Then FISH program was used to get the location data of slip plane from displacement contour lines. Furthermore, the method to determine multiple slip planes was also proposed by setting different heights of elastic areas. The influential factors for the stability were analyzed, including cohesion, internal friction angle, and tensile strength. The calculation results show that with the increase of cohesion, failure mode of slope changes from shallow slipping to the deep slipping, while inclination of slip plane becomes slower and slipping volume becomes larger; with the increase of friction angle, failure mode of slope changes from deep slipping to shallow slipping, while slip plane becomes steeper and upper border of slip plane comes closer to the vertex of slope; the safety factor increases little and slip plane goes far away from vertex of slope with the increase of tensile strength. Foundation item: Project(20060533071) supported by the Doctoral Program Foundation of Higher Education of China; Project (20060400264) supported by China Postdoctoral Science Foundation; Project (50774093) supported by the National Natural Science Foundation of China; Project (1343-74236000014) supported by Graduate Student Innovation Foundation of Hunan Province, China     

Effect of stirring on preparation of hollow copolymer particles by alkali/cooling method

Hollow particles were prepared by the treatment of styrene-methacrylic acid copolymer particles with alkali/cooling method. The influences of stirring position (in aqueous phase or at the interface of O/W) and stirring speed (90, 110 and 240 r/min) on the formation of hollow particles were investigated. It is found that the soft stirring in aqueous phase at 90 r/min leads to the formation of monohollow particles, while the violent stirring at the interface of O/W and 240 r/min gives non-hollow products. In contrast, the weak stirring in aqueous phase at 110 r/min results in sterically heterogeneous dispersion of methacrylic acid-rich regions within the original particles, and hence the formation of multihollow particles. Further investigation indicates that the change of stirring efficiency provides a way to tune the diffusion behavior of monomer styrene, and therefore influences the distribution of methacrylic acid units in the original particles as well as the morphology of the treated particles. Foundation item: Project supported by China Scholarship Council; Project(09JJ3100) supported by Hunan Provincial Natural Science Foundation of China     

Automatic brush-plating technology for component remanufacturing

An automatic brush-plating system was developed for component remanufacturing. With this system, Ni/nano-alumina composite coatings from an electrolyte containing 20 g/L nano-alumina particles were prepared. Microstructure, surface morphology, microhardness and wear resistance of automatically plated coating and manually plated coatings were investigated comparatively. The results show that the automatically plated coatings are relatively dense and uniform and have lower friction coefficient of 0.089 under lubricant condition, when compared with manually plated coatings with friction coefficient of 0.14. Foundation item: Project(50235030) supported by the National Natural Science Foundation of China; Project(G1999065009) supported by the National Basic Research Program of China     

Simulation of people＇s evacuation in tunnel fire

The simulation model Tunev（tunnel evacuation） was developed for people＇s evacuation in tunnel fire. It contains simple database of the people＇s behavioral reaction and structure characteristic parameters of tunnel fireproofing. The model can be used to calculate the total evacuation time in various scenes when fire occurs in the different locations of the tunnel. Combined with fire simulation soft ware CFD- POENICS3.5, Tunev model can be used to calculate the fire danger coming time; by comparing with these two kinds of time, it can be used to assess the safety of the evacuation, and the evacuation process also have a dynamic demo. The simulation results show that the Tunev model can be used to predict the reliability of safe evacuation for people in tunnel fire and provide references for people＇s safe escape scheme. Some relevant concepts of the model were described and an evacuation simulation of a typical tunnel case, i.e. Xuefeng Mountain Tunnel was performed by using this model. And the model＇s validation and actual aoolication were also described.