Investigations on the Machinability of Al/SiC/RHA Hybrid Metal Matrix Composites

Silicon - Hybrid aluminum metal matrix composites (MMC’s) are the emerging materials that gain superior properties in terms of hardness, specific strength, mechanical and physical properties...     

Effect of SiC Weight Percentage on Tribological Characteristics of Al7075/SiC Composites

Silicon - In aerospace and automobile industries, because of high strength and excellent anti-wear properties, aluminium silicon carbide composites are widely used. Hence, the current work...     

Studies on Egg Shell and SiC Reinforced Hybrid Metal Matrix Composite for Tribological Applications

Silicon - The hybrid metal matrix composite is developed through stir casting process. In theAl7075 aluminium matrix material, two different combination of reinforcements are used to make hybrid...     

Ti3SiC2/SiC复合材料的抗高温氧化性研究

采用反应热压烧结法制备Ti3 SiC2/SiC复合材料,针对不同SiC含量的Ti3 SiC2/SiC复合材料在1100 ～ 1500℃下恒温氧化20h的氧化行为进行了研究.结果表明:(1)适量SiC的引入能有效的提高Ti3 SiC2/SiC复合材料的抗高温氧化性能;(2)复合材料的氧化膜分内外两层,外层成分为TiO2,逐渐向内层过渡为TiO2和SiO2的混合物.     

Characteristics Study of Physical,Mechanical and Tribological Behaviour of SiC/TiB2 Dispersed Aluminium Matrix Composite

Silicon - SiC and TiB2 particle reinforced Al7075 matrix composite has numerous applications such as aircraft structures, mould tool manufacturing, and structural application due to less weight to...     

Effect of Insitu Formed TiB2 Particles on Tribological Behaviour of Al-Si/Mg2Si Hybrid Composites

Silicon - This work investigates the effect of insitu formed TiB2 particles on tribological behaviour of Al-Si/Mg2Si hybrid composites. For this purpose, different amount of TiB2 particles (0, 1,...     

碳化硅陶瓷在不同湿度下的滑动摩擦行为研究

本文研究了碳化硅陶瓷对氧化铝陶瓷在不同湿度下的滑动摩擦行为。在高湿度的条件下,摩擦系数和磨损均有降低,根据微区元素分析结果,在摩痕表面形成氧化层是摩擦行为改善的主要原因。     

Synthesis of Cu-10Sn/SiC Metal Matrix Composites and Experimental Investigation of its Adhesive Wear Behaviour

Silicon - The objective is to fabricate Cu-10Sn alloy and its composites reinforced with varying wt% of SiC (5, 10 and 15) to investigate its dry sliding wear behaviour. Microstructural analysis...     

Mechanical and Tribological Properties of AA6061/SiC/Aloe Vera Powder Hybrid Al Composites Fabricated by Stir Casting

Silicon - Aluminium Matrix Composites (AMC) are fabricated through the stir casting route is more beneficial in comparison with other techniques since the methodology is inexpensive, easier in...     

SiCf/SiC复合材料高温抗氧化研究进展

连续SiC纤维增韧SiC陶瓷基复合材料(SiCf/SiC CMCs)具有低密度、优异的高温力学性能和抗氧化性能,在航空发动机热端部件上具有广阔的应用前景,具备提高发动机推重比和使用温度、减轻无效重量、简化系统结构等显著优势.延长SiCf/SiC复合材料在航空发动机高温氧化环境下的服役寿命是当前需要解决的难题.本文从纤维、界面相、基体、表面涂层四个方面综述了SiCf/SiC复合材料高温抗氧化研究进展.采用多元多层自愈合界面相、对基体进行改性以及采用表面自愈合整体涂层都可以有效提高SiCf/SiC复合材料在高温氧化环境中的使用稳定性和寿命.     

Investigation of Weight Percentage of Alumina Fiber on EDM of Al/Al2O3 Metal Matrix Composites

This paper aims to study the influence of Al₂O₃ particle addition to Al alloys. The effects of reinforcement volumes in a metal matrix alloy on response variables were investigated towards the highlighting of this process with the goal of achieving high process performance. In this study, the comparison between EDM of Al/Al₂ O ₃ metal matrix composites with different volumes of reinforcement and 2024 alloys was investigated to determine the influence of weight percentage of Al₂ O ₃-reinforced particles on output parameters. The results show that addition of Al₂ O ₃ particles in the composites has significant effects on material removal rate, surface roughness and tool wear rate. Tool wear rate and surface roughness were increased with increased Al₂ O ₃ ceramic contents. Surface roughness was obviously affected by the discharge current as well as pulse on-time. Rapid increase in tool wear rate was seen when reinforced with higher weight percentage of Al₂O₃ particles. The pulse on-time and discharge current significantly affect the material removal rate, tool wear rate and surface roughness. Tool wear rate, material removal rate and surface roughness were high if the discharge current and pulse on-time were set at a higher level. In other words, high current and pulse on-time resulted in high tool wear rate, material removal rate and surface roughness. The material removal rate was decreased by increasing the weight percentage of Al₂O₃ particles.

     

金属基复合材料的摩擦学性能及结合强度试验研究

以聚酰胺66（PA66）、聚苯硫醚(PPS) 及65Mn钢板为主要原料,制备了一系列不同配比的金属基复合材料,并对这些材料进行不同条件下的摩擦学性能试验,最后通过结合强度试验来分析材料间的结合强度。结果表明,复合材料的摩擦因数及磨损速率随着聚酰胺66的增加而降低;同种材料的摩擦系数及磨损速率随着载荷和对摩速度的增加而先增大后减小;结合强度试验表明金属基复合材料的结合强度随着聚苯硫醚的增加而逐渐增大。     

PS/纳米MoS2复合材料的研究

采用熔融共混的方法制备了PS/纳米MoS2复合材料,并应用高阻仪、DSC等研究了该复合材料的电性能和热性能,同时测试了该复合材料的力学性能.结果表明,随着纳米MoS2用量的增加,复合材料的体积电阻率明显下降,当MoS2用量为25份时,复合材料的体积电阻率达到109Ω·cm;复合材料的热稳定性也得到提高;同时,复合材料的拉伸强度和冲击强度提高,而弯曲强度有所降低.     

Effect of SiC Content on Mechanical and Tribological Properties of Al2024-SiC Composites

Silicon - Aluminium matrix composites are scientifically engineered materials possessing higher potential in automotive, aerospace and defence applications. Therefore this study focuses on the...     

SiC／Al复合材料的组织与力学性能研究

采用无压浸渗法制备了SiC／Al复合材料．研究不同颗粒大小的复合材料的抗弯强度、金相组织和断裂机理。结果表明：颗粒尺寸为20um的SiC／Al复合材料抗弯强度最高：小颗粒复合材料的断裂以沿晶断裂为主,局部有韧性撕裂的特征,而大颗粒还伴有穿晶解理特征。     

Three-Body Abrasive Wear Behaviour of Polymer Matrix Composites Filled with SiC Particles

Effect of filler material on three-body abrasive wear behaviour of Glass – Epoxy composites has been investigated. The abrading distance, applied load and sliding speed are the parameters used for the study. A L9 orthogonal array and ANOVA were used to identify the contribution of individual parameters. The result shows that the weight loss increases with increase in load, sliding speed and abrading distance. The abrading distance has more effect on the wear compared to other parameters. The filler material (SiC) contributes a significant wear resistance of the G–E composites.     

Fatigue Mechanisms in Graphite/SiC Composites at Room and High Temperature

Some deductions have been made from fractographic evidence about mechanisms of low-cycle mechanical fatigue in plain woven graphite/SiC composites at room and high temperature in vacuum. At both room temperature and 830°C, fatigue appears to be confined to the crack wake, where attrition reduces the efficacy of bridging fibers. It is inferred that the crack tip advances at some critical value of the crack tip stress intensity factor, as in monotonic growth, rather than by any intrinsic fatigue mechanism in the matrix. However, the manifestations of attrition are very different at room and high temperatures. At high temperature, wear is greatly accelerated by the action of SiC debris within the crack. This distinction is rationalized in terms of the temperature dependence expected in the opening displacement of a bridged crack. This argument leads in turn to plausible explanations of trends in loadlife curves and the morphology of cracks as the temperature rises.     

2D-SiC/SiC陶瓷基复合材料的拉伸本构模型研究

通过单向拉伸试验,研究了2D-SiC/SiC复合材料的应力-应变行为.结果表明,材料单向拉伸应力-应变曲线表现出明显的双线性特征,且线弹性段较长.通过试件断口照片,分析了2D-SiC/SiC复合材料单向拉伸破坏机理和损伤模式.基于对损伤过程的假设,建立了二维连续纤维增强陶瓷基复合材料的双线性本构模型,并将其应用于2D-SiC/SiC复合材料的应力-应变曲线模拟,模拟结果与试验值吻合很好.同时,分析计算表明,2D-SiC/SiC复合材料的单轴拉伸行为主要由纵向纤维柬决定,横向纤维对材料的整体模量和强度贡献很小.     

Electrical Resistance of SiC Fiber Reinforced SiC/Si Matrix Composites at Room Temperature during Tensile Testing

The implementation of Ceramic Matrix Composites necessitates the understanding of stress‐dependent damage evolution. Toward this goal, two liquid silicon infiltrated SiCf reinforced SiC composites were tensile tested with electrical resistance (ER) monitoring as well as acoustic emission to quantify matrix cracking. ER was modeled using a combination of resistors in series and parallel to model transverse matrix cracks and fiber/matrix segments between matrix cracks. It is shown that resistance change is sensitive to transverse matrix crack formation and stress‐dependent debonding length. The model appears to be accurate up to the stress for matrix crack saturation.