两边连接交叉加劲钢板剪力墙弹性屈曲分析

采用ANSYS有限元软件对两边连接交叉加劲钢板剪力墙进行了弹性屈曲分析,重点研究了加劲肋与墙板的刚度比、墙板高厚比、边长比以及加劲肋宽厚比对弹性屈曲系数的影响,并将分析结果与十字加劲板进行了比较.研究表明,交叉加劲肋能够显著提高钢板剪力墙的弹性屈曲荷载,其远大于十字加劲肋;随着墙板边长比和高厚比的增大,屈曲系数趋于减小;而较小的加劲肋宽厚比能使墙板获得较大的屈曲系数;最后给出了两边连接交叉加劲板弹性屈曲系数的计算公式.     

On braced trapezoidal corrugated steel shear panels: An experimental and numerical study

In this study, a new system consisting of a combination of braces and steel infill panels called the braced corrugated steel shear panel (BCSSP) is presented. To obtain the hysteretic behavior of the proposed system, the quasi-static cyclic performances of two experimental specimens were first evaluated. The finite element modeling method was then verified based on the obtained experimental results. Additional numerical evaluations were carried out to investigate the effects of different parameters on the system. Subsequently, a relationship was established to estimate the buckling shear strength of the system without considering residual stresses. The results obtained from the parametric study indicate that the corrugated steel shear panel (CSSP) with the specifications of a = 30 mm, t = 2 mm, and θ = 90° had the highest energy dissipation capacity and ultimate strength while the CSSP with the specifications of a = 30 mm, t = 2 mm, and θ = 30° had the highest initial stiffness. It can thus be concluded that the latter CSSP has the best structural performance and that increasing the number of corrugations, corrugation angle, and plate thickness and decreasing the sub-panel width generally enhance the performance of CSSPs in terms of the stability of their hysteretic behaviors.     

交叉加劲钢板剪力墙弹性屈曲研究

用有限元方法对交叉加劲钢板剪力墙的弹性屈曲性能进行了研究,重点研究了加劲肋与墙板的刚度比、墙板高厚比、边长比以及加劲肋宽厚比等对弹性屈曲系数k的影响,同时与十字加劲板的抗剪屈曲性能进行了对比。研究结果表明,设置交叉加劲肋能显著提高钢板剪力墙的弹性屈曲荷载;屈曲系数k随着墙板边长比、高厚比以及加劲肋宽厚比的增大而趋于减小;本文给出的交叉加劲板弹性屈曲系数k的计算公式与有限元法的结果较吻合。     

钢板剪力墙低周反复荷载试验研究

本文进行了6个13比例钢板剪力墙的低周反复荷载试验,重点研究了钢板墙极限承载力和滞回性能,为钢板墙结构利用屈曲后强度及抗震设计提供试验依据;本试验揭示了边柱局部屈曲、加劲肋布置形式、加劲板刚度和板高厚比对钢板墙滞回性能的影响。试验结果表明,边柱不出现局部屈曲是钢板墙发挥极限承载力的重要保证;厚板和较强的加劲肋对提高钢板墙滞回曲线的饱满度和滞回环面积是有利的;三种钢板墙以交叉加劲板的承载力和滞回性能最佳,十字加劲板次之,钢板墙结构耗能能力依赖于钢板与边柱的弹塑性变形和钢板面外鼓曲变形。试验曲线与应用弹塑性大挠度有限元法计算的滞回曲线吻合良好;利用屈曲后强度的钢板墙受剪承载力,其试验值与本课题建议公式及有限元值计算结果基本一致。     

Analysis on shear capacity and energy dissipation of corrugated steel plate shear wall with openings

为明确波形钢板剪力墙不发生屈曲的界限条件并分析开洞对其承载力及耗能能力的影响，基于波形钢板剪切屈曲理论推导其屈曲应力计算式，并采用数值分析及变形等级划分方法得到约束刚度比取值范围，由此提出波形钢板剪力墙不发生屈曲的界限条件为屈曲应力大于剪切屈服应力且约束刚度比大于3。通过对比开洞模型的变形等级计算参数，验证界限条件对开洞波形钢板墙的适用性，建立有限元模型研究钢板墙高宽比、钢板厚度、开洞率、洞口高宽比及洞口位置对波形钢板墙承载力及耗能能力的影响。结果表明：钢板高宽比越小、板厚越大，开洞对其承载力及耗能能力的削弱程度越大，洞口高宽比在0.33~0.5之间时开洞波形钢板墙的承载力及耗能最大，中心开洞时的最小。基于波形钢板剪力墙全截面剪切屈服的受力机理对其受剪承载力和塑性耗能计算式进行推导，并通过拟合得到考虑洞口参数影响的开洞波形钢板剪力墙受剪承载力及耗能折减系数计算式；通过9组不开洞模型和30组不同洞口尺寸及位置的开洞模型对计算式的有效性进行验证。结果表明计算值与模拟值的误差均在15%以内，适用于满足无屈曲界限条件的开洞波形钢板剪力墙。     

开洞波形钢板剪力墙受剪承载力及耗能能力分析

为明确波形钢板剪力墙不发生屈曲的界限条件并分析开洞对其承载力及耗能能力的影响,基于波形钢板剪切屈曲理论推导其屈曲应力计算式,并采用数值分析及变形等级划分方法得到约束刚度比取值范围,由此提出波形钢板剪力墙不发生屈曲的界限条件为屈曲应力大于剪切屈服应力且约束刚度比大于3。通过对比开洞模型的变形等级计算参数,验证界限条件对开洞波形钢板墙的适用性,建立有限元模型研究钢板墙高宽比、钢板厚度、开洞率、洞口高宽比及洞口位置对波形钢板墙承载力及耗能能力的影响。结果表明：钢板高宽比越小、板厚越大,开洞对其承载力及耗能能力的削弱程度越大,洞口高宽比在0.33～0.5之间时开洞波形钢板墙的承载力及耗能最大,中心开洞时的最小。基于波形钢板剪力墙全截面剪切屈服的受力机理对其受剪承载力和塑性耗能计算式进行推导,并通过拟合得到考虑洞口参数影响的开洞波形钢板剪力墙受剪承载力及耗能折减系数计算式;通过9组不开洞模型和30组不同洞口尺寸及位置的开洞模型对计算式的有效性进行验证。结果表明计算值与模拟值的误差均在15%以内,适用于满足无屈曲界限条件的开洞波形钢板剪力墙。     

钢板剪力墙弹塑性分析

分析了钢板墙从弹性屈曲到拉力带全部屈服的受力全过程。在弹性屈曲阶段,引入了弹性嵌固系数以考虑框架约束的影响。在弹塑性阶段,考虑了拉力带倾角、塑性变形系数和屈服后阶段弹性模量折减等影响,用斜拉杆模型合理地模拟了拉力带的受力过程,推导了斜拉杆初始屈服应力、极限应力、钢板墙剪力和位移计算公式。分别计算了钢板和纯框架的单独作用,然后再考虑其组合作用,得到了钢板墙的弹塑性荷载-位移曲线,通过算例验证了公式的有效性。     

十字加劲钢板剪力墙的抗剪极限承载力

我国《高层民用建筑钢结构技术规程》规定了钢板墙剪切弹性屈曲不先于剪切屈服,其明显的不足是没有利用板的屈曲后强度,同时弹性屈曲也不能作为结构在弹塑性阶段的设计指标。本文应用板的大挠度弹塑性有限元方法对十字加劲方形钢板剪力墙的屈曲后性能和极限承载力进行了系统的研究,并在大量数值分析的基础上,提出了以板的平均剪切应变相应的剪应力作为钢板剪力墙承载能力的极限状态,以达到利用薄板屈曲后强度的目的,进而提出了钢板剪力墙承载力的设计简化计算公式及钢板墙侧柱刚度阈值的计算公式,供设计参考。数值计算结果表明,影响钢板墙抗剪性能主要有三个参数:板高厚比、肋板刚度比和边柱刚度。     

Experimental investigation on the behavior of corrugated steel shear wall subjected to the different angle of trapezoidal plate

Studies on corrugated steel shear walls (CSSWs) generally indicate noticeable increase of energy absorption, as well as increasing shear buckling capacity of corrugated plates being more likely rather than the flat plates. In this paper, the effect of variation in the angle of trapezoidal plate on the behavior of CSSWs has extensively been investigated. Three specimens of CSSW with 1 story and single bay in half scale are tested under cyclic load. The observations of experiment do indicate that stress concentration has been increased in the corner of subpanels, by increasing of the corrugation angle. Development of the tensile field and wall yield and damage depends on the geometry of the plate. By increasing the corrugation angle, the stiffness and energy dissipation decrease; in addition, large loss of strength takes place. Comparing the numerical and experimental results indicates that for a closer look at behavior of trapezoidal CSSWs, fracture mechanics, fatigue, and damping of materials should be considered by numerical analysis.     

Shear buckling strength and design of curved corrugated steel webs for bridges

This paper presents the shear buckling strength and design of curved corrugated steel webs for bridges considering material inelasticity. The inelastic buckling strength is determined from buckling curves based on the proposed shear buckling parameter, which is a function of the elastic shear buckling strength of steel web and the material shear yielding strength. A finite element analysis is carried out to study the geometric parameters affecting the shear buckling strength of curved corrugated steel webs for bridges. Based on the numerical results, a shear buckling parameter formula is proposed with no need to calculate either local, global, or interactive buckling parameters. But it depends on the geometric properties of the curved corrugated web profile. Another formula is presented to maximize the shear buckling capacity of curved corrugated web. The proposed formulae agreed well with the published experimental data. The curved corrugated webs produce a tremendous increase in the shear buckling strength and considerable weight saving in regard to the corresponding trapezoidal corrugated webs. The corrugation angle has a considerable effect on the behavior of curved corrugated webs, where higher corrugation angles produce a tremendous increase in the shear buckling strength of curved corrugated webs. It was found that the proposed approach provides a good prediction for the shear buckling strength of curved corrugated steel webs of bridges.     

不锈钢薄腹梁受剪性能试验研究

通过对7根不锈钢薄腹梁进行受剪性能试验研究,分析了梁腹板的剪切屈曲和屈曲后强度。结果表明：所有梁均发生剪切屈曲破坏,薄腹板中形成拉力带,上翼缘和横向加劲肋中出现塑性铰;根据腹板表面应变和侧向鼓曲变形测得的剪切屈曲应力均低于理论计算的弹性剪切屈曲应力;梁的受剪承载力显著高于腹板剪切屈曲时的荷载,具有较高的屈曲后强度;梁端设置封头肋板可以提高梁的受剪承载力。基于得出的试验结果及现有其他试验数据,对两种考虑腹板屈曲后强度的受剪承载力计算方法进行评估,我国GB 50017—2017《钢结构设计标准》中的公式仅考虑了腹板的受剪承载力,其计算结果总体偏于保守,但是对腹板高厚比较小(λs<1.5)的不锈钢薄腹梁,受剪承载力计算偏于不安全,且计算结果离散性较大;EN 1993-1-4中的计算公式中同时考虑了腹板和翼缘的受剪承载力,其计算结果偏于保守且离散性较小。     

钢板剪力墙简化模型研究

本文用斜拉杆简化模型分析了钢板墙从弹性屈曲到拉力带全部屈服的受力全过程。考虑了真实的拉力带倾角、塑性变形系数和屈服后阶段弹模折减等因素影响,用斜拉杆模型模拟了拉力带的受力过程,推导了斜拉杆初始屈服应力、极限应力、钢板墙剪力和位移计算公式,得到了钢板墙的弹塑性荷载-位移曲线,最后与试验资料比较验证了公式的有效性。     

Elastic shear buckling characteristics of LiteSteel beams

LiteSteel beam (LSB) is a new cold-formed steel hollow flange channel beam. The unique LSB section is produced by a patented manufacturing process involving simultaneous cold-forming and dual electric resistance welding. To date, limited research has been undertaken on the shear buckling behaviour of LSBs with torsionally rigid, rectangular hollow flanges. For the shear design of LSB web panels, their elastic shear buckling strength must be determined accurately including the potential post-buckling strength. Currently the elastic shear buckling coefficients of web panels are determined by assuming conservatively that the web panels are simply supported at the junction between the flange and web elements. Therefore finite element analyses were carried out to investigate the elastic shear buckling behaviour of LSB sections including the effect of true support conditions at the junction between their flange and web elements. An improved equation for the higher elastic shear buckling coefficient of LSBs was developed and included in the shear capacity equations of Australian cold-formed steel codes. Predicted ultimate shear capacity results were compared with available experimental results, both of which showed considerable improvement to the shear capacities of LSBs. A study on the shear flow distribution of LSBs was also undertaken prior to the elastic buckling analysis study. This paper presents the details of this investigation and the results including the shear flow distribution of LSBs.     

The wall–frame and the steel–concrete interactions in composite shear walls

The nonlinear pushover analyses of 24 composite steel plate shear walls (CSPSWs), 24 corresponding steel plate shear walls (SPSWs), and 24 corresponding frames are conducted. CSPSWs have different aspect ratios and infill steel plate thicknesses. The study aims to understand the wall–frame and steel–concrete interactions. The infill steel plate thickness and aspect ratio of CSPSW are the main parameters of the study. In CSPSWs, the percentage of absorbed shear forces by the infill composite wall is always greater than the infill plate of its corresponding SPSW. The percentage of shear in the composite wall is constant at the initial stage of loading up to a drift of 0.15–0.2%. By increasing the drift, the shear yielding of steel plate leads to a reduction of the shear force absorption. The reduction continues until the bulk of shear stiffness of CSPSW is provided by the frame. At the beginning of lateral loading, steel–concrete interactions increase until shear yield of steel plate. Following this stage, a sudden decrease takes place in shear force absorption of reinforced concrete (RC) panel. The reason is that, at the lower drifts, the steel plate has a tendency for elastic buckling, which is prevented by the RC panel. Finally, the shear force absorption remains approximately constant in the RC panel.     

两边连接屈曲约束钢板剪力墙受力机理与等效支撑模型

采用理论分析和有限元方法,针对两边连接屈曲约束钢板剪力墙的受力机理和传力规律进行研究。提出了钢板墙边缘约束区的概念并确定了边缘约束区的宽度,分析了钢板墙的屈服形状、钢板墙内各部分应力流的分布规律和钢板墙与梁连接处的受力特点等。在此基础上提出了两边连接屈曲约束钢板剪力墙等效支撑模型,对不同尺寸、不同层数的框架 屈曲约束钢板剪力墙结构和框架 等效支撑结构在水平荷载作用下的力学性能进行分析,并对两种结构的荷载 位移曲线进行了对比。分析表明,所提出的等效支撑模型在结构刚度和承载力方面具有较好的准确性,无论是单调加载还是反复加载均能准确地模拟两边连接屈曲约束钢板剪力墙结构的受力行为。     

两侧边开缝钢板剪力墙弹性屈曲分析

提出一种新型的两侧边开缝的钢板剪力墙,并对其两侧边有无加劲肋的两种结构形式进行有限元弹性屈曲分析,分别讨论其临界屈曲荷栽和屈曲模态。对两侧无加劲肋的钢板剪力墙,给出用于其设计的屈曲系数公式,对两侧有加劲肋的钢板剪力墙给出具有参考价值的设计建议。     

Concrete panel thickness demand for the design of composite steel plate shear wall

Composite steel plate shear walls (C‐SPWs) are composed of an infill steel plate and reinforced concrete encasements. With an adequate thickness, the concrete encasement can effectively prevent the premature buckling of the infill steel plate. Researchers have provided nonconservative concrete thickness demands through analyses of approximate elastic buckling, for which the analytical model is too simplistic to simulate C‐SPW buckling. In this paper, the buckling of C‐SPW is addressed using a nonlinear finite element method. To assist this method, a formula for the buckling strength of C‐SPW is theoretically developed. Utilizing the results of nonlinear finite element analysis on C‐SPW, the effects of concrete panel thickness, concrete elastic modulus, infill steel plate thickness, panel aspect ratio, and stud spacing on the infill steel plate buckling are analyzed, and the critical drift ratio corresponding to the buckling of the infill steel plate is obtained. According to the criterion that the C‐SPW will not buckle until its drift ratio achieves the drift limit (0.4%), the minimum concrete panel thicknesses demands are captured from finite element analysis. Fitting these predicted minimum concrete thicknesses, an available formula is proposed for the concrete thickness demand in the design of C‐SPW.     

波形钢腹板PC组合箱梁在玉春桥中的应用研究

针对一座波形钢腹板PC组合箱梁桥——玉春车行天桥,对其波形钢腹板和抗剪连接键的设计与构造进行了介绍,并对波形钢腹板和抗剪连接键的受力性能进行了计算分析,计算结果表明,在正常使用极限状态下,钢板的剪应力满足规范要求,且不会在钢板剪切屈服之前发生局部屈曲、整体屈曲或合成屈曲的破坏形式;剪力连接键的抗剪承载能力满足使用要求且具有较大的安全裕度。     

Shear strength and design of trapezoidally corrugated steel webs

Due to the accordion effect, corrugated steel webs are only able to resist shear force. The shear force in the web can cause three different buckling modes: local, global and interactive shear buckling. Although several researchers have been investigating it, the shear buckling behavior of the corrugated webs has not yet been clearly explained, this leads to conservative design. This paper presents the shear strength and design of trapezoidally corrugated steel webs. Firstly, global shear buckling equations are rearranged in order to derive the global shear buckling coefficient. The interactive shear buckling coefficient and the shear buckling parameter for corrugated steel webs are then proposed based on the 1st order interactive buckling equation. The inelastic buckling strength is determined from the buckling curves based on the proposed shear buckling parameter. A series of tests are conducted to verify the proposed design equations. From the test results of this study and those provided by previous researchers, it was found that the proposed shear strengths provide good predictions for the shear strength of the corrugated steel webs.     

Behavior of framed modular building system with double skin steel panels

A new type of lateral force-resisting system, a framed modular building with double skin steel panels of slender thin steel plates is presented. Modular construction leads to faster construction, improved quality and reduced resources and waste. A steel panel strengthened framed modular system is developed for the lateral load resisting system instead of in situ concrete core walls. The proposed double skin steel panel systems showed moderate ductility and energy dissipation due to their post-buckling strength. Full-scale experiments on a framed modular system with double skin steel panels were conducted. The test of the frame with steel panel systems showed that all steel panel systems reached a yielding point before the frame structure started to yield, so that severe damage to the frame as a primary structure was controlled. Also, the steel panel systems increased the initial lateral stiffness of the total system and maintained the elastic range of the panels up to near the yielding point of plates without local buckling driven from its shear behavior. By rigid-plastic analysis, the post-buckling strength of thin plates under in-plane bending was predicted and compared with experimental results. Based on the experimental data of the panels, the analytic model of these panel systems was constructed and compared with the experimental results of frames with double skin steel panel systems.