Biodegradable biocomposites from poly(butylene adipate‐co‐terephthalate) and miscanthus: Preparation,compatibilization, and performance evaluation

Miscanthus fibers reinforced biodegradable poly(butylene adipate‐co‐terephthalate) (PBAT) matrix‐based biocomposites were produced by melt processing. The performances of the produced PBAT/miscanthus composites were evaluated by means of mechanical, thermal, and morphological analysis. Compared to neat PBAT, the flexural strength, flexural modulus, storage modulus, and tensile modulus were increased after the addition of miscanthus fibers into the PBAT matrix. These improvements were attributed to the strong reinforcing effect of miscanthus fibers. The polarity difference between the PBAT matrix and the miscanthus fibers leads to weak interaction between the phases in the resulting composites. This weak interaction was evidenced in the impact strength and tensile strength of the uncompatibilized PBAT composites. Therefore, maleic anhydride (MAH)‐grafted PBAT was prepared as compatibilizer by melt free radical grafting reaction. The MAH grafting on the PBAT was confirmed by Fourier transform infrared spectroscopy. The interfacial bonding between the miscanthus fibers and PBAT was improved with the addition of 5 wt % of MAH‐grafted PBAT (MAH‐g‐PBAT) compatibilizer. The improved interaction between the PBAT and the miscanthus fiber was corroborated with mechanical and morphological properties. The compatibilized PBAT composite with 40 wt % miscanthus fibers exhibited an average heat deflection temperature of 81 °C, notched Izod impact strength of 184 J/m, tensile strength of 19.4 MPa, and flexural strength of 22 MPa. From the scanning electron microscopy analysis, better interaction between the components can be observed in the compatibilized composites, which contribute to enhanced mechanical properties. Overall, the addition of miscanthus fibers into a PBAT matrix showed a significant benefit in terms of economic competitiveness and functional performances. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 45448.     

Preparation,crystallization, and properties of biodegradable poly(butylene adipate‐co‐terephthalate)/organomodified montmorillonite nanocomposites

Intercalated and exfoliated nanocomposites of biodegradable poly(butylene adipate‐co‐terephthalate) (PBAT) and Cloisite 30B (C30B) were fabricated by a solution‐casting method to study the effects of the clay loading on the crystallization behavior, thermal stability, and dynamic mechanical properties of PBAT in PBAT/C30B nanocomposites. X‐ray diffraction and transmission electron microscopy results indicated the formation of exfoliated nanocomposites at low clay loadings (<5 wt %) and a mixture of exfoliated and intercalated nanocomposites with a clay content of 8 wt % throughout the PBAT matrix. Nonisothermal melt crystallization studies indicated that C30B enhanced the crystallization of PBAT, apparently because of a heterogeneous nucleation effect. Moreover, an attempt was made to quantitatively study the influence of the presence of C30B and its contents on the nucleation activity of PBAT in the PBAT/C30B nanocomposites. The thermal stability of PBAT decreased slightly in the nanocomposites. However, the storage modulus of PBAT apparently increased with the C30B loading increasing in the PBAT/C30B nanocomposites. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Formulation and characterization of compatibilized poly(lactic acid)‐based blends and their nanocomposites with silver‐loaded kaolinite

Biodegradable polymer nanocomposites have been developed in this study as materials for use in the packaging of moisture‐sensitive products. Poly(lactic acid) (PLA) was the main component of the nanocomposites with poly(butylene adipate‐co‐terephthalate) (PBAT) as flexibility enhancer. Tetrabutyl titanate was also added as a compatibilizer to enhance the interfacial affinity between PLA and PBAT by inducing the formation of some PLA/PBAT via transesterification during the melt blending process, thereby improving the mechanical properties of the blends. Silver‐loaded kaolinite synthesized via chemical reduction was also incorporated into the compatibilized blends for further property improvement. Herein, we report a novel biodegradable quaternary nanocomposite system with intercalated‐exfoliated clay dispersion that was uniquely achieved by increasing the interlamellar space between kaolinite layers through silver nanoparticle insertion. The resultant nanocomposites containing as little as 4 phr modified clay reduced the elongation at break from 213.0 ± 5.85% to 53.8 ± 1.81%, enhanced thermal stability (initial decomposition temperature increased from 378 °C to 399 °C) and exhibited a water vapor permeability reduction of 41.85%. On the basis of these properties, the developed nanocomposites are considered to be promising candidates for use in bio‐packaging applications to replace non‐biodegradable and petro‐based plastics. © 2014 Society of Chemical Industry     

Properties of poly(butylene adipate‐co‐terephthalate) and sunflower head residue biocomposites

Utilization of low‐value agricultural waste for polymer composite materials has great environmental and economical benefits. Sunflower head residue (SHR) as an agricultural waste may be used as a reinforcement in polymeric materials because of its fiber characteristics. In this work, composites of biodegradable poly(butylene adipate‐co‐terephthalate) (PBAT) and SHR were prepared via melt‐extrusion compounding. To improve interfacial compatibility, maleic anhydride (MA) grafted PBAT (PBAT‐g‐MA) was prepared and used as a compatibilizer for the PBAT/SHR composites. The effects of the concentrations of SHR and PBAT‐g‐MA on the morphology, mechanical properties, melt rheology, and water resistance of the composites were examined. Interfacial adhesion between phases in the PBAT/SHR composites was enhanced by the introduction PBAT‐g‐MA as interface‐strengthening agent, resulting in improved mechanical properties and moisture resistance of the composite. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 44644.     

Cellulose nanocrystal‐based poly(butylene adipate‐co‐terephthalate) nanocomposites covered with antimicrobial silver thin films

In this study, we reported the preparation and prospective application of the nanocomposites of poly(butylene adipate‐co‐terephthalate) (PBAT) reinforced with cellulose nanocrystals (CNCs). CNCs were isolated from bleached sugarcane bagasse by acid hydrolysis and functionalized with adipic acid. Nanocomposites were prepared with different concentration of CNCs (0.8, 1.5, and 2.3 wt% CNC) by solution‐casting method and then were covered with silver thin film by magnetron sputtering. The results showed that the surface modification increased the degree of crystallinity of nanocrystals from 51% to 56%, decreasing their length and diameter. Moreover, AFM‐IR spectroscopy revealed that the modified CNCs were covered by adipic acid molecules, improving the dispersion of nanocrystals in PBAT. Well‐dispersed modified CNCs acted as heterogeneous nuclei for crystallization of PBAT, and increased the storage modulus of the polymer by more than 200%. These improvements in thermal and mechanical properties of CNC‐based PBAT associated with the decrease of 56% in the Escherichia coli biofilm formation on nanocomposites (antibacterial properties) qualify the CNC/PBAT nanocomposites covered with silver thin films to be used as food packaging. POLYM. ENG. SCI., 59:E356–E365, 2019. © 2019 Society of Plastics Engineers     

Effect of γ‐radiation on the thermal and mechanical properties of a commercial poly(butylene adipate‐co‐terephthalate)

BACKGROUND: Poly(butylene adipate‐co‐terephthalate) (PBAT) has attracted wide interest as a biodegradable polymer. However, its use is restricted in certain applications due to its low melting point. RESULTS: PBAT was treated using γ‐radiation. The radiation features were analyzed using Soxhlet extraction, and the ratio of chain scission and crosslinking and gelation dose were determined using the classical Charlesby–Pinner equation. The results showed that PBAT is a radiation‐crosslinkable polymer. The degree of crosslinking increased with increasing radiation dose; the relation between sol fraction and dose followed the Charlesby–Pinner equation. Differential scanning calorimetry analyses showed that the melting temperature (T_m) and the heat of fusion (ΔH_m) of PBAT exhibited almost no change in the first scan. The second scan, however, showed a decrease in T_m and ΔH_m. The glass transition temperature of irradiated PBAT increased with increasing radiation dose. The weight loss of control and irradiated PBAT resulting from thermal degradation was a one‐step process. Moreover, the tensile strength and elongation at break decreased with an increase in radiation dose. However, the Young's modulus and stress at yield were not greatly affected by γ‐radiation. CONCLUSION: PBAT can be crosslinked using γ‐radiation. The crosslinking efficiency is relatively low. The thermal and mechanical properties of PBAT are affected by γ‐radiation. Copyright © 2009 Society of Chemical Industry     

Bio‐based polymer nanocomposites based on layered silicates having a reactive and renewable intercalant

Soybean oil‐based polymer nanocomposites were synthesized from acrylated epoxidized soybean oil (AESO) combined with styrene monomer and montmorillonite (MMT) clay by using in situ free radical polymerization reaction. Special attention was paid to the modification of MMT clay, which was carried out by methacryl‐functionalized and quaternized derivative of methyl oleate intercalant. It was synthesized from olive oil triglyceride, as a renewable intercalant. The resultant nanocomposites were characterized by X‐ray diffraction (XRD) and transmission electron microscopy (TEM). The effect of increased nanofiller loading in thermal and mechanical properties of the nanocomposites was investigated by thermogravimetric analysis (TGA) and dynamic mechanical analysis (DMA). The nanocomposites exhibited improved thermal and dynamic mechanical properties compared with neat acrylated epoxidized soybean oil based polymer matrix. The desired exfoliated nanocomposite structure was achieved when the OrgMMT loading was 1 and 2 wt % whereas partially exfoliated nanocomposite was obtained in 3 wt % loading. It was found that about 400 and 500% increments in storage modulus at glass transition and rubbery regions, respectively were achieved at 2 wt % clay loading compared to neat polymer matrix while the lowest thermal degradation rate was gained by introducing 3 wt % clay loading. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 130: 2031–2041, 2013     

In situ compatibilization of maleated thermoplastic starch/polyester melt‐blends by reactive extrusion

This article concerns the utilization of maleated thermoplastic starch (MTPS) in the reactive extrusion melt‐blending with poly(butylene adipate‐co‐terephthalate) (PBAT) in blown film applications. First, MTPS was prepared from cornstarch with glycerol (plasticizer) and maleic anhydride (MA; esterification agent). MTPS was then melt‐blended with PBAT in a subsequent downstream extrusion operation. The effects of both polyester and MA contents were studied on the physicochemical parameters of melt‐blends. For high polyester fractions (>60 wt%), PBAT‐g‐MTPS graft copolymers were obtained through transesterification reactions. They were promoted by the MA‐derived acidic moieties grafted onto the starch backbone as shown by selective Soxhlet extraction experiments and FTIR analyses. At lower polyester content, no significant reaction occurred more likely due to an inversion in the phase morphology between both components. Tensile properties of PBAT‐g‐MTPS graft copolymer containing 70 wt% polyester were much higher as the TPS/PBAT melt‐blend modified with MA. This can be explained by a finer morphology of the dispersed phase in the continuous PBAT matrix, and an increased interfacial area for the grafting reaction as attested by morphological studies. POLYM. ENG. SCI., 2008. © 2008 Society of Plastics Engineers.     

Property enhancement in polypropylene ternary blend nanocomposites via a novel poly(ethylene oxide)‐grafted polystyrene‐block‐poly(ethylene/butylene)‐block‐polystyrene toughener–compatibilizer system

Synthesis and characterization of a novel toughener–compatibilizer for polypropylene (PP)–montmorillonite (MMT) nanocomposites were conducted to provide enhanced mechanical and thermal properties. Poly(ethylene oxide) (PEO) blocks were synthetically grafted onto maleic anhydride‐grafted polystyrene‐block‐poly(ethylene/butylene)‐block‐polystyrene (SEBS‐g‐MA). Special attention was paid to emphasize the effect of PEO‐grafted SEBS (SEBS‐g‐PEO) against SEBS‐g‐MA on morphology, static/dynamic mechanical properties and surface hydrophilicity of the resultant blends and nanocomposites. It was found that the silicate layers of neat MMT are well separated by PEO chains chemically bonded to nonpolar SEBS polymer without needing any organophilic modification of the clay as confirmed by X‐ray diffraction and transmission electron microscopy analyses. From scanning electron microscopy analyses, elastomeric domains interacting with MMT layers via PEO sites were found to be distributed in the PP matrix with higher number and smaller sizes than the corresponding blend. As a benefit of PEO grafting, SEBS‐g‐PEO‐containing nanocomposite exhibited not only higher toughness/impact strength but also increased creep recovery, as compared to corresponding SEBS‐g‐MA‐containing nanocomposite and neat PP. The damping parameter of the same nanocomposite was also found to be high in a broad range of temperatures as another advantage of the SEBS‐g‐PEO toughener–compatibilizer. The water contact angles of the blends and nanocomposites were found to be lower than that of neat hydrophobic PP which is desirable for finishing processes such as dyeing and coating. © 2018 Society of Chemical Industry     

Nanocomposites based on poly(butylene adipate‐co‐terephthalate) and montmorillonite

Nanocomposites based on biodegradable poly(butylene adipate‐co‐terephthalate) (PBAT) and layered silicates were prepared by the melt intercalation method. Nonmodified montmorillonite (MMT) and organo‐modified MMTs (DA‐M, ODA‐M, and LEA‐M) by the protonated ammonium cations of dodecylamine, octadecylamine, and N‐lauryldiethanolamine, respectively, were used as the layered silicates. The comparison of interlayer spacing between clay and PBAT composites with inorganic content 3 wt % measured by X‐ray diffraction (XRD) revealed the formation of intercalated nanocomposites in DA‐M and LEA‐M. In case of PBAT/ODA‐M (3 wt %), no clear peak related to interlayer spacing was observed. From morphological studies using transmission electron microscopy, the ODA‐M was found to be finely and homogeneously dispersed in the matrix polymer, indicating the formation of exfoliated nanocomposite. When ODA‐M content was increased, the XRD peak related to intercalated clay increased. Although the exfoliated ODA‐M (3 wt %) nanocomposite showed a lower tensile modulus than the intercalated DA‐M and LEA‐M (3 wt %) composites, the PBAT/ODA‐M composite with inorganic content 5 wt % showed the highest tensile modulus, strength, and elongation at break among the PBAT composites with inorganic content 5 wt %. Their tensile properties are discussed in relation to the degree of crystallinity of the injection molded samples. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 95: 386–392, 2005     

Antimicrobial activity and biodegradation behavior of poly(butylene adipate‐co‐terephthalate)/clay nanocomposites

Poly(butylene adipate‐co‐terephthalate) (PBAT) nanocomposites films are prepared by a solution intercalation process using natural montmorillonite (MMT) and cetyltrimethylammonium bromide (CTAB)‐modified montmorillonite (CMMT). Cation exchange technique has been used for modification of MMT by CTAB and characterized by Fourier transform infrared analysis, thermo‐gravimetric analysis, and X‐ray diffraction (XRD) studies. CMMT gives better dispersion in the PBAT matrix than MMT and is confirmed by XRD and transmission electron microscopy. Because of better compatibility of CMMT, water vapor transmission rate of PBAT decreases more in the presence of CMMT than MMT. The biodegradability of PBAT and its nanocomposite films are studied in compost and from the morphological analysis it is apparent that the PBAT/CMMT shows a lower biodegradation rate in comparison to the PBAT/MMT. The antimicrobial activity of PBAT and its nanocomposite films is tested by an inhibition zone method. Because of the presence of the quaternary ammonium group of CTAB‐modified MMT, PBAT/CMMT nanocomposites show adequate antimicrobial activity. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40079.     

Poly(vinyl chloride‐co‐vinyl acetate‐co‐maleic anhydride)/silica nanocomposites derived from in situ suspension polymerization

Poly(vinyl chloride‐co‐vinyl acetate‐co‐maleic anhydride) (PVVM)/silica nanocomposites were prepared by the suspension radical copolymerization of the monomers in the presence of fumed silica premodified with γ‐methylacryloxypropl trimethoxy siliane. Morphological observation showed that the silica particles of nanometer scale were well dispersed in the copolymer matrix of the nanocomposites films, whereas silica particles tended to agglomerate in the composites films prepared by the solution blending of PVVM with silica. The experimental results show that the thermal stability, glass‐transition temperature, tensile strength, and Young's modulus were significantly enhanced by the incorporation of silica nanoparticles. The enhancement of properties was related to the better dispersion of silica particles in polymer matrix and the interaction between the polymer chains and the surfaces of the silica particles. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Crystallization behavior of fully biodegradable poly(lactic acid)/poly(butylene adipate‐co‐terephthalate) blends

Both poly(lactic acid) (PLA) and poly(butylene adipate‐co‐terephthalate) (PBAT) are fully biodegradable polyesters. The disadvantages of poor mechanical properties of PLA limit its wide application. Fully biodegradable polymer blends were prepared by blending PLA with PBAT. Crystallization behavior of neat and blended PLA was investigated by differential scanning calorimetry (DSC), polarizing optical microscopy (POM), and wide angle X‐ray diffraction (WAXD). Experiment results indicated that in comparison with neat PLA, the degree of crystallinity of PLA in various blends all markedly was increased, and the crystallization mechanism almost did not change. The equilibrium melting point of PLA initially decreased with the increase of PBAT content and then increased when PBAT content in the blends was 60 wt % compared to neat PLA. In the case of the isothermal crystallization of neat PLA and its blends at the temperature range of 123–142°C, neat PLA and its blends exhibited bell shape curves for the growth rates, and the maximum crystallization rate of neat PLA and its blends all depended on crystallization temperature and their component. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Thermal properties and degradation behavior of poly(1,4‐butylene adipate)/modified layered double hydroxide nanocomposites

In this study, poly(1,4‐butylene adipate) (PBA)/organomodified layered double hydroxide (m‐LDH) nanocomposites were synthesized and characterized as a new material for green materials use. m‐LDH was initially prepared with magnesium nitrate hexahydrate, aluminum nitrate‐9‐hydrate, oleic acid, and sorbitol by a novel one‐step coprecipitation method to intercalate the oleic acid and sorbitol organomodifier into the interlayer of the layered double hydroxide. The solution mixing process was then applied and shown to be an efficient method for fabricating the PBA/m‐LDH nanocomposites. The m‐LDH characterized by X‐ray diffraction (XRD) showed a high interlayer spacing of 58.8 Å. The morphology and thermal properties of the PBA/m‐LDH nanocomposites were characterized with XRD, transmission electron microscopy, and thermogravimetric analysis. It was shown that the m‐LDH was well distributed in the PBA matrix and that the thermal properties of the PBA/m‐LDH nanocomposites significantly improved with a loading of 0.1 wt % m‐LDH. Finally, the biodegradability of the PBA/m‐LDH nanocomposites was tested with lipase from Pseudomonas fluorescens as a microbial catalyst. It was shown that an addition of m‐LDH up to 0.5% resulted in a significant difference in terms of the biodegradability. After 120 h of degradation, the residual weight and surface morphology of the composite films were affected by the presence of m‐LDH. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42083.     

Effects of poly(butylene adipate‐co‐terephthalate) and ultrafined wollastonite on the physical properties and crystallization of recycled poly(ethylene terephthalate)

Recycled poly(ethylene terephthalate) (rPET), obtained mainly from postconsumer bottles, was melt‐mixed with either poly(butylene adipate‐co‐terephthalate) (PBAT) or PBAT plus ultrafine wollastonite (～5 μm) at different weight ratios on a twin‐screw extruder and then injection‐molded. Among the five rPET/PBAT blends (10–50 wt% PBAT) evaluated, the 80/20 wt% rPET/PBAT blend exhibited the highest tensile strength and degree of crystallinity, a slight increase in the tensile strain, and a remarkable increase in the melt flow index, but a lower tensile modulus and thermal stability with respect to the neat rPET. This blend was subsequently filled with four loading levels of wollastonite (10–40 wt%), where the tensile properties (modulus, strain at break, and strength) and thermal stability of the blend were all improved by the addition of wollastonite in a dose‐dependent manner. Based on differential scanning calorimetry analysis, the crystallinity of rPET in the rPET/PBAT/wollastonite composites decreased in the presence of wollastonite, accompanied with a noticeable increase in the glass transition, cold crystallization, and crystallization temperatures, but only a slight change in the melting temperature was noted compared with those of the neat 80/20 wt% blend. Moreover, the addition of wollastonite at 30 wt% or higher showed a strong reduction in the melt dripping of the composites during combustion. J. VINYL ADDIT. TECHNOL., 23:106–116, 2017. © 2015 Society of Plastics Engineers     

Characterization,degradation and biocompatibility of PBAT based nanocomposites

The characterization, biocompatibility and hydrolytic degradation of poly(butylene adipate-co-terephthalate) (PBAT) and its nanocomposites based on 10 wt.% of an unmodified sepiolite and unmodified and modified montmorillonites and fluorohectorites were studied. All nanocomposites were prepared by melt blending using an internal mixer at 140 °C, showing a good level of clay distribution and dispersion into the PBAT matrix, especially those systems based on modified clays and sepiolite. The compression tests of all nanocomposites showed significant increases in the mechanical properties of PBAT matrix, associated to a reinforcement effect of nanoclays. An effective hydrolytic degradation of PBAT and nanocomposites in a phosphate buffered solution of pH 7.0 at 37 °C was also obtained. The addition of nanoparticles tended to delay slightly the hydrolysis of the polymer matrix in the early degradation stages; afterwards the presence of nanoparticles did not affect significantly the degradation trend of the polymer. Cytotoxicity tests, protein absorption analyses and complete blood count tests indicated that nanocomposites showed good biological safety: non-cytotoxicity, higher in vitro hemocompatibility than neat PBAT and non-negative hemostatic effects after contacting with blood. In general, these results showed that all the studied PBAT based nanocomposites could be very attractive for various tissue engineering applications, particularly to bone defects.     

Synthesis of a new compatibilisant agent PVC‐g‐MA and its use in the PVC/alfa composites

The main objective of this research was to synthesize a new compatibilisant agent (PVC‐g‐MA), which was grafted from the maleic anhydride on the PVC chains. The presence of maleic anhydride grafting on PVC was made evident by infrared analysis. PVC‐g‐MA was used like compatibilisant to solve the problem of the incompatibility between the hydrophobic polymeric matrix (PVC) and hydrophilic fiber (alfa). Composites samples were prepared with different alfa fiber loading (10, 20, and 30 wt %) and incorporating PVC‐g‐MA (1, 3, and 5 wt %) or PP‐g‐MA (3 wt %). The tensile properties, the thermal stability and the morphology of the composites were investigated. The result indicated that the PVC‐g‐MA increased the interfacial adhesion between the fibers and the polymer matrix and this effect was better than that obtained for the maleated‐polypropylene‐coupled composites. Microstructure analysis of the fractured surfaces of MAPP modified composites confirmed improved interfacial bonding. The addition of alfa and PVC‐g‐MA increased the thermal stability of the composites. The temperature of degradation of the polymer matrix increased about 16°C in comparison to the noncoupled composite, indicating that PVC‐g‐MA improved the thermal stability of the polymer. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Nanoclay‐reinforced poly(butylene adipate‐co‐terephthalate) biocomposites for packaging applications

Increasing generation and inadequate disposal of waste progressively compromise our environment. Solutions are proposed by the development of biodegradable polymers, that is, for short‐term applications like packaging. The present study focuses on the design and characterization of biodegradable poly(butylene adipate‐co‐terephthalate) (PBAT) nanocomposites reinforced by different types of nanoclays. The addition of natural and modified montmorillonite and bentonite to PBAT by melt mixing enhances slightly the thermal stability and increases the crystallization temperature, independently of the fillers' dispersion state. By contrast, storage modulus in dynamic mechanical analysis is increased when adding nanoclay, and improvement is higher for well‐dispersed organomodified fillers. Dispersion states and morphology of the nanocomposites are studied by X‐ray diffraction as well as scanning and transmission electron microscopy. PBAT‐based composites with modified bentonite reveal to show the best performance at room temperature (which is the temperature of interest for potential packaging applications) in comparison with the other investigated nanocomposites.POLYM. COMPOS., 33:2022–2028, 2012. © 2012 Society of Plastics Engineers     

Mechanical and morphological properties of poly(butylene adipate‐co‐terephthalate) and poly(lactic acid) blended with organically modified silicate layers

Poly(butylene adipate‐co‐terephthalate) (PBAT) is a biodegradable polymer with high ultimate elongation but low modulus. This work studied the addition of a rigid bio‐based and biodegradable polymer, poly(lactic acid) (PLA), along with organically modified silicate layers as a conceivable means to improve the modulus of PBAT. Blending with PLA would also reduce both the cost of the ultimate blend and its dependence on nonrenewable resources. Compounds of PBAT with PLA and organically modified silicate layers showed significantly improved tensile and flexural strength resulting in enhanced thermomechanical performances compared to neat PBAT. The state of clay dispersion was evaluated using common analytical techniques such as transmission electron microscopy, X‐ray diffraction, and rheometry. The clay platelets were partially dispersed in a PBAT and PLA phase and a large portion of the platelets were located at the interface. The incorporation of organoclay reduced the dispersed phase domain (i.e., PLA) size significantly. The smaller PLA size however, did not translate into better elongational properties. POLYM. ENG. SCI., 2012. © 2012 Society of Plastics Engineers     

Morphology and thermal behavior of poly (3‐hydroxybutyrate‐co‐3‐hydroxyvalerate)/poly(butylene adipate‐co‐terephthalate)/clay nanocomposites

Biopolymers are gaining increasing interest because of decline of mineral oil reserves, increasing waste problem, and increasing consciousness of society for environmental problems. However, competitiveness of biopolymers compared with conventional plastics is still limited due to partly insufficient properties and high prices. This study investigates the influence of blending of poly(hydroxybutyrate‐co‐hydroxyvalerate) (PHBV) with poly(butylene adipate‐co‐terephthalate) (PBAT) as well as the influence of addition of functionalized montmorillonite (OMMT) to the blends on morphology and thermal behavior. Dispersion state and morphology of the nanocomposites are studied by X‐ray diffraction as well as scanning electron microscopy. Thermal stability is studied by thermogravimetric analysis and crystallization behavior is studied by differential scanning calorimetry and polarized optical microscopy. With respect to the morphology for the blends it can be seen that the immiscible biopolymers PHBV and PBAT are distributed in interlocking zones. There is a good dispersion and homogeneous distribution of OMMT within the biopolymer blends. The addition of 50% or more PBAT to PHBV as well as the insertion of OMMT enhances thermal stability of PHBV. In the blends, the addition of PBAT retards crystallization of PHBV. The OMMT acts as nucleating agent leading in total to more but less perfect crystals in the blends, and the crystallization slows further due to constraint in the movement of polymer chains. These results contribute to the understanding of the structure–properties relationship of bionanocomposite materials for packaging applications. POLYM. COMPOS., 36:2051–2058, 2015. © 2014 Society of Plastics Engineer