Dynamic–mechanical properties of modified poly(ethylene‐co‐vinyl acetate)

To study the relationship among relaxation peaks observed in dynamic mechanical experiments and the structure of poly(ethylene‐co‐vinyl acetate) (EVA), EVA copolymers with different substitution in the carbonyl group were synthesized. EVA was hydrolyzed to obtain poly (ethylene‐co‐vinyl alcohol) and was subsequently reacted with formic, hexanoic, and octanoic acids. The copolymers synthesized were characterized by infrared spectroscopy. Analysis of the DMA spectra of the copolymers showed that their relaxation behavior depends on the vinyl acetate concentration. The α‐ and β‐transitions were observed in EVA copolymers with 8 and 18 wt % of functional groups, and the relationship among relaxation process with the structure of polymer was investigated. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 97: 1371–1376, 2005     

Morphological control of porous ethylene‐vinyl acetate copolymer membrane obtained from a co‐continuous ethylene‐vinyl acetate copolymer/poly(ϵ‐caprolactone) blend

Ethylene‐vinyl acetate copolymer (EVA)/poly(?‐caprolactone) (PCL) blend (50/50 w/w) with co‐continuous morphology was prepared via melt mixing for fabricating microporous EVA membrane materials through selective solvent extraction. Shear flow and quiescent annealing techniques were employed to control co‐continuous phase size in the EVA/PCL blend, and the time‐ and temperature‐dependent relations of phase size were then evaluated theoretically. Using these techniques, microporous EVA membrane materials with various pore sizes ranging from 2 µm to more than 200 µm were obtained. In contrast to the porous EVA membrane prepared by the traditional way of solvent casting/particulate leaching, the as‐obtained microporous membrane shows a higher level of interconnectivity and much narrower pore size distribution with uniform pore structure. © 2013 Society of Chemical Industry     

Evaluation of mechanical properties and physical interactions of a ternary blend of poly(ethylene‐co‐octene)/poly(ethylene‐co‐vinyl acetate)/poly(vinyl chloride) in the molten state

In this work, ethylene‐co‐vinyl acetate (EVA), poly(ethylene‐co‐octene) (POE), and poly(vinyl chloride) (PVC) blends were processed in a molten state process using a corotating twin‐screw extruder to assess both the balance of mechanical properties and physical interactions in the melt state. Tensile measurements, scanning electron microscopy, and oscillatory rheometry were performed. By means of flow curves, the parameters of the power law as well as the distribution of relaxation times were assessed with the aid of a nonlinear regularization method. The mechanical properties for the EVA‐POE blend approximated the values for POE, while inclusion of PVC shifted the modulus values to those of neat EVA. The rise in modulus was corroborated by the PVC phase dispersion as solid particles that act as a reinforcement for the ternary blend. The rheological properties in the molten state show that the POE does not present molecular entanglement effects and so tends both to diminish the EVA mechanical properties and increase the fluidity of the blend. However, the addition of PVC both restored the EVA typical pseudoplastic feature and promoted the increase in the viscosity and the mechanical properties of the ternary blend. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Foaming of poly(ethylene‐co‐vinyl acetate) and poly(ethylene‐co‐vinyl acetate‐co‐carbon monoxide) and their blends with carbon dioxide

Poly(ethylene‐co‐vinyl acetate) (EVA‐25) and poly(ethylene‐co‐vinyl acetate‐co‐carbon monoxide) (EVACO‐2410) and their blends with EVACO:EVA ratios of 80:20, 60:40, 40:60, and 20:80 were foamed using CO₂. These foams are of interest for applications ranging from footwear to medical devices. Foaming experiments were carried out using 1 mm thick melt‐extruded films in CO₂ at a range of pressures (100, 200, and 300 bar) and temperatures (30, 40, 50, and 60 °C). Foamability of the polymers was explored both under isothermal and gradient temperature conditions. Foams of EVACO‐2410 displayed high initial expansions followed by postfoaming relaxation and shrinkage while foams generated from EVA‐25 showed more dimensional stability. Blending EVACO‐2410 with EVA‐25 was explored as an approach to reduce postfoaming relaxation and shrinkage. The surfaces of the foamed samples displayed blistering that was linked to CO₂ bubble entrapment and coalescence at the surface. Scanning electron micrographs of the foams generated from blends displayed distinct morphologies reflecting whether the sections were representing the machine‐ or cross‐machine direction of extruded films. In going from EVACO‐2410 to EVA‐25, the cell densities ranged from about 10⁶ to 10¹⁰ cells/cm³. Foams with low bulk densities of about 0.11 g/cm³ could be generated. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 45841.     

Barrier properties of poly(ethylene‐co‐vinyl acetate)/cellulose composite membranes

Poly(ethylene‐co‐vinyl acetate) (EVA)/cellulose composite membranes were prepared and their vapor permeation characteristics were studied. Two types of EVA [having vinyl acetate contents of 18% (EVA18) and of 40% (EVA40), respectively] were used for the composite fabrication. Cellulose, isolated from banana waste fibers, was used as the filler. It was observed that the EVA40 composites were more permeating than were the EVA18 composites. This observation is explained on the basis of more amorphous nature of EVA40 as compared to EVA18. The extent of vapor permeation decreased with increase in the cellulose content in the composites. The presence of voids in the polymer membranes that were designed to possess controlled behavior for the permeation was confirmed using scanning electron microscopic images to complement the observations made during the permeation studies. The influence of molecular weight, molar size, and polarity of the penetrants, on the permeation process, was also considered. The permeability of the membrane samples was calculated and the values obtained were compared with the theoretical values provided by using the modified Neilson permeability equation. POLYM. ENG. SCI., 2012. © 2012 Society of Plastics Engineers     

Structure and properties of flame‐sprayed poly(ethylene‐co‐vinyl alcohol) copolymer coatings

Powder coatings formed by flame spraying are being used in industrial applications. The resistance of plastics and their composite materials to chemicals, solvents, and atmospheric conditions and their high impact strength even at low service temperatures increase the importance of plastic and plastic‐based coatings. In this study, an ethylene vinyl alcohol copolymer powder was coated via flame spraying with gases of oxygen and acetylene. The bond strengths and microstructures of the coatings were determined with tensile testing, scanning electron microscopy, and Fourier transform infrared. The bond strengths of the coatings were determined according to ASTM C 633. Oxidizing, carburizing, and neutral flames were used. The bond strengths were lower for the oxidizing and carburizing coatings than for the neutral flame coatings. The results indicated that during the flame‐spraying process, the composition, gas, spraying distance, and coating thickness were important factors in the coating bond strength. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 94: 1357–1364, 2004     

Solid‐state NMR and morphological studies of poly(ethylene‐co‐vinyl acetate)/poly(vinyl acetate) blends

To obtain a correlation among structure–morphology–mobility–compatibility properties of poly(ethylene‐co‐vinyl acetate) (EVA)/poly(vinyl acetate) (PVAc) blends, we have used scanning electron microscopy and solid‐state nuclear magnetic resonance in our investigations. The results are discussed in terms of blends, component dispersion, plasticization effect, and domain mobilities to acquire a response of the correlation between structural properties. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 74: 2990–2996, 1999     

The effectiveness of magnesium carbonate‐based flame retardants for poly(ethylene‐co‐vinyl acetate) and poly(ethylene‐co‐ethyl acrylate)

In this report we outline recent work on the evaluation of magnesium carbonate‐based flame retardants for polymers commonly used in halogen‐free flame retardant wire and cable applications: poly(ethylene‐co‐vinyl acetate) (EVA) and poly(ethylene‐co‐ethyl acrylate) (EEA). Natural magnesium carbonate (magnesite), synthetic magnesium carbonate (hydromagnesite), and hydromagnesite/huntite blends were combined with EVA or EEA and tested for flame retardancy effectiveness with the cone calorimeter. The flammability results showed that the effectiveness of these carbonates was polymer dependent, suggesting that polymer degradation chemistry played a role in the flammability reduction mechanism. Hydromagnesites were, in general, more effective in reducing flammability, being comparable in performance to magnesium hydroxide. Finally, we report some polymer–clay (organically treated montmorillonite and magadiite) + magnesium carbonate flame retardant results which showed that the nanocomposite yielded mixed results. Specifically, the polymer–clay nanocomposite samples did not always yield the greatest reductions in peak heat release rate. Copyright © 2007 John Wiley & Sons, Ltd.     

Melt grafting of poly(ethylene‐vinyl acetate) copolymer with maleic anhydride

Poly(ethylene‐vinyl acetate) (EVA) copolymer was melt grafted with maleic anhydride (MAH) in a twin screw extruder in the presence of peroxide. It is confirmed that MAH has been melt grafted on the backbone of EVA by FTIR using the method of hydrolysis. The NMR analysis suggests that the grafting reaction occurs on the tertiary carbon of main chain of EVA other than the methyl moiety of vinyl acetate (VA) group. The incorporation of VA groups onto the matrix shows a competitive effect on the grafting. The existence of VA groups promotes the extent of MAH graft onto EVA; nevertheless, it also weakens the crystallizability of main chain. When the content of peroxide initiator is 0.1 wt % based on the polymer matrix, the grafting degree increases with increasing the concentration of monomer. When the peroxide content is higher than 0.1 wt %, side reactions such as crosslinking or disproportionation will be introduced into this system. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 841–846, 2006     

Effects of peroxide crosslinking on the mechanical and morphological properties of poly(ethylene‐co‐vinyl acetate)/zeolite composites

Uncrosslinked and chemically crosslinked ethylene‐vinyl acetate copolymers (EVAs) with 5–25 volume percentages of zeolite were prepared in a melt‐mixing process and then compression‐molded on a hot‐press machine according to standard test specifications. The mechanical properties measured by tensile test showed a reduction in tensile strength and elongation at break with increasing zeolite content. However, an increasing trend was observed for tensile modulus with addition of zeolite. Experimental results for ultimate stress were compared with those from Pukanszky equation. The experimental data showed a good fit to the Pukanszky model. The improvement in the interfacial interaction for crosslinked composites was also confirmed by this model. Morphological changes of EVA/zeolite composites were analyzed by scanning electron microscopy (SEM). The fractured surface of the composites indicated more complex morphology at higher zeolite loading. The influence of crosslinking induced by 2 wt% of dicumyl peroxide on the properties of EVA/zeolite composites was also investigated. The crosslinked composites showed better tensile properties than the uncrosslinked ones, a result which might be an indication of enhanced interaction between the EVA and zeolite. Density measurements, gel content determinations, and Fourier transform infrared analyses were also performed to evaluate the crosslink content of the composites. The changes in the properties of chemically crosslinked EVA/zeolite composites were observed. Meanwhile, SEM micrographs of the crosslinked EVA/zeolite composites showed better interfacial strength between zeolite and the EVA matrix as compared to that of the uncrosslinked composites. J. VINYL ADDIT. TECHNOL., 2012. © 2012 Society of Plastics Engineers     

Viscoelasticity and morphology of poly(ethylene‐co‐vinyl acetate)/polyisobutylene blends

Blends of an ethylene/vinyl acetate copolymer (EVA) and polyisobutylene of various compositions were prepared by mechanical mixing at a temperature above the melting point of EVA (T_m^EVA) but below the upper critical solution temperature of 170°C for given blends. The rheological properties of the components and blends were studied in the region of small‐amplitude oscillating deformation at temperatures above and below T_m^EVA in the frequency range of 0.01–100 rad/s. At temperatures lower than T_m^EVA, the rheological properties were determined by the existence of the yield stress. With diminishing frequency, the viscosity increased, and the plateau in the relaxation spectrum at low frequencies broadened. The morphology of the blends depended on the conditions of sample heating. The introduction of a finely dispersed filler into the blends led to an anomalous drop in the viscosity. The morphology of the systems that arose by mechanical blending of the molten components was the important factor in the rheological behavior. The observed effects were examined in the framework of the concept of structural networks formed in melts by nonmelted crystallites of EVA. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 2700–2707, 2006     

Fabrication,characterization, and properties of poly(ethylene‐co‐vinyl acetate)/magnetite nanocomposites

Poly(ethylene‐co‐vinyl acetate) (EVA)/magnetite (Fe₃O₄) nanocomposite was prepared with different loading of Fe₃O₄ nanoparticles. The mixing and compounding were carried out on a two‐roll mixing mill and the sheets were prepared in a compression‐molding machine. The effect of loading of nanoparticles in EVA was investigated thoroughly by different characterization technique such as transmission electron microscopy (TEM), X‐ray diffraction (XRD), differential scanning calorimetry (DSC), thermogravimetric analysis (TGA), limiting oxygen index (LOI), and technological properties. TEM analysis showed the uniform dispersion of filler in the polymer matrix and the dispersion of filler decreased with increase in filler content. XRD of the nanocomposite revealed the more ordered structure of the polymer chain. An appreciable increase in glass transition temperature was observed owing to the restricted mobility of Fe₃O₄‐filled EVA nanocomposite. TGA and flame resistance studies indicated that the composites attain better thermal and flame resistance than EVA owing to the interaction of filler and polymer segments. Mechanical properties such as tensile strength, tear resistance, and modulus were increased for composites up to 7 phr of filler, which is presumably owing to aggregation of Fe₃O₄ nanoparticle at higher loading. The presence of Fe₃O₄ nanoparticles in the polymer matrix reduced the elongation at break and impact strength while improved hardness of the composite than unfilled EVA. The change in technological properties had been correlated with the variation of polymer–filler interaction estimated from the swelling behavior. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40116.     

Production of polymeric membranes made of polypropylene,poly(ethylene‐co‐vinyl acetate), and poly(vinyl alcohol)

In this study, we prepared and characterized membranes containing polypropylene, poly(ethylene‐co‐vinyl acetate) (EVA), and poly(vinyl alcohol) (PVA). The production process involved blend extrusion and calendering followed by solvent extraction by toluene and water of the EVA and PVA phases. Morphology studies involving scanning electron microscopy determined the pore size distribution at the surface and in the internal regions of the membrane. The resulting membrane properties were related to the processing variables (extension rate, process temperature, and solvent extraction methods) and blend composition. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 3275–3286, 2004     

Poly(ethylene‐co‐vinyl acetate) blends with phenoxy

EVA was blended with phenoxy over the whole range of composition using a twin‐screw Brabender. Two‐phase separation caused by EVA crystallization was observed in the EVA‐rich blends and the dispersed domain of EVA was not clearly shown in the phenoxy‐rich blends. Differential scanning calorimetry (DSC) showed that the glass transition temperature (T_g) of EVA was increased by 5–10°C in the EVA‐rich blends but the T_g of phenoxy was superposed over the melting behavior of EVA. X‐ray diffraction measurement indicated that EVA crystallization was restricted in the phenoxy‐rich blends and the EVA crystal structure was influenced by incorporation of phenoxy into the EVA‐rich blends. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 73: 227–236, 1999     

Effect of poly(ethylene‐co‐vinyl acetate) additive on mechanical properties of maleic anhydride‐grafted acrylonitrile butadiene styrene for coating applications

The Izod impact strength of maleic anhydride‐grafted acrylonitrile butadiene styrene (MA‐g‐ABS) copolymer has been improved by the use of rubbery poly(ethylene‐co‐vinyl acetate) (EVA). The MA‐g‐ABS is prepared by an internal mixer using dicumyl peroxide as free radical initiator, and the grafting degree was determined using back‐titration method. The amount of EVA is optimized by evaluating the Izod impact strength, tensile, and flexural properties of the samples. Addition of 6% EVA into MA‐g‐ABS system improved the Izod impact strength and tensile strength by 18% and 35%, respectively. The miscibility of EVA in ABS and MA‐g‐ABS matrices has been observed using differential scanning calorimetry and scanning electron microscopy techniques. The enhanced adhesion property exhibited by MA‐g‐ABS/EVA systems promises it as a good candidate for thermoplastic coating applications on aluminum substrates. J. VINYL ADDIT. TECHNOL., 25:287–295, 2019. © 2018 Society of Plastics Engineers     

Use of pyrolyzed oil shale as filler in poly(ethylene‐co‐vinyl acetate) with different vinyl acetate contents

Pyrolyzed oil shale (POS) obtained from the pyrolysis of bituminous rock was used as filler in poly(ethylene‐co‐vinyl acetate) (EVA). The effects of the VA content of EVA and the particle size of POS on the mechanical properties were investigated. The composites were prepared in a rotor mixer at 180°C with a concentration of POS of up to 30 wt %. The stress–strain plots of the compression‐molded composites are similar to the EVA (18% VA content) behavior for low concentrations (1–5 wt %) of POS with a particle size lower than 270 mesh. It was observed that decreasing the POS particle size and increasing the VA content of EVA produced better compatibility between the polymer and filler. The mechanical properties, differential scanning calorimetry, and dynamic mechanical analysis also demonstrated the compatibility between EVA and POS under the increase of the VA content in the EVA. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 84: 1544–1555, 2002; DOI 10.1002/app.10494     

Effect of nanocellulose fibers and acetylated nanocellulose fibers on properties of poly(ethylene‐co‐vinyl acetate) foams

Cellulose nanofibers are promising materials in the development of polymeric foams, because they act as heterogeneous nucleation sites for the growth of cells during foaming. In this research, we studied the incorporation of cellulose nanoparticles in poly(ethylene‐co‐vinyl acetate)‐EVA foams. The foams were produced with different fiber contents. We observed the effect of a chemical treatment by acetylation on the cellulose fibber, that is, we evaluated the use of hydrophilic and hydrophobic cellulose nanofibers in EVA foams. The main results indicate that with the addition of only 1% of cellulose nanofibers, cell density significantly reduces when compared with the pure EVA foams. On the other hand, by increasing the cellulose content, the agglomeration of nanofibers also increases, which results in heterogeneous cell sizes. The same phenomenon was observed in the foams produced with acetylated cellulose nanofibers, regardless of the fiber content used. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 44760.     

Microstructure and thermal properties of ethylene‐(vinyl acetate) copolymer/rectorite nanocomposites

Ethylene‐(vinyl acetate) copolymer (EVA)/rectorite nanocomposites were prepared by direct melt extrusion of EVA and organo‐rectorite. The microstructures and thermal properties of EVA nanocomposites were characterized by X‐ray diffraction (XRD), scanning electron microscopy (SEM), solid‐state nuclear magnetic spectroscopy, positron annihilation spectroscopy, thermal gravimetric analysis (TGA) and dynamic mechanical analysis techniques. XRD pattern and SEM images show that the intercalated structure is formed and rectorite is finely dispersed in EVA matrix. When organoclay content of the hybrid increases to 7.5 wt%, or pristine rectorite was used instead of organoclay, the crystallization behavior of EVA nanocomposite changes greatly and the ratio of the monoclinic to orthorhombic crystal increases significantly. The relative fractional free volume of the nanocomposite decreases with the increasing organo‐rectorite content, and the values of damping factor (tan δ) for all nanocomposites are lower than that of pure EVA. These facts illuminate that intercalated structure restricts the segment motion and mobilization of polymer chain. TGA results of EVA nanocomposites in air indicate that deacylation of EVA is accelerated because of the catalytic effect and the thermal degradation of the main chain is delayed owing to the barrier effect of silicate layers. Copyright © 2005 Society of Chemical Industry     

Influence of screw speed on the mechanical and rheological properties of poly(ethylene‐co‐vinyl acetate)—organomodified montmorillonite nanocomposites

Poly(ethylene‐co‐vinyl acetate) (EVA) and organophilic montmorillonite clay nanocomposites were manufactured in a co‐rotating twin‐screw extruder using screw speeds ranging between 200 and 800 rpm. The morphology and thermal‐mechanical and rheological properties were studied to establish processing–morphology–property relationships. Particularly for samples produced under higher screw speed ranges, X‐ray diffraction and transmission electron microscopy revealed a tendency of increased exfoliated clay. Although the mechanical properties improved by the presence of clay, they were not altered by the screw speed. The rheological behavior in the solid and melt states were evaluated and showed that the storage modulus of neat EVA subjected to higher screw speed undergoes more pronounced decrease in the storage modulus than the nanocomposites, suggesting that the clay minimizes the effect of the screw speed. This minimization effect could be explained in the light of the assessment of relaxation times that showed stronger physical interactions with the nanocomposites in the molten state. POLYM. COMPOS., 36:854–860, 2015. © 2014 Society of Plastics Engineers     

Surface photocrosslinking of ethylene–vinyl acetate copolymer films

Surface photocrosslinking of ethylene–vinyl acetate (EVAc) copolymer films containing benzophenone (BP) was investigated for the purpose of replacing a poly(vinyl chloride) floor. The photogelatin in the EVAc films was effectively observed after UV radiation in the presence of oxygen. The crosslinking reaction was initiated from the surface of the irradiated film, which was mainly due to the dehydrogenation and generation of macroradicals of polymer by the light absorption of BP. The experiments of polyethylene–VAc with BP showed that the VAc‐rich amorphous part in the EVAc copolymer works as a crosslinking site. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 76: 1741–1745, 2000