A novel β‐nucleating agent for isotactic polypropylene

The nucleating ability of p‐cyclohexylamide carboxybenzene (β‐NA) towards isotactic polypropylene (iPP) was investigated by differential scanning calorimetry, X‐ray diffraction, polarized optical microscopy and scanning electron microscopy. β‐NA is identified to have dual nucleating ability for α‐iPP and β‐iPP under appropriate kinetic conditions. The formation of β‐iPP is dependent on the content of β‐NA. The content of β‐phase can reach as high as 96.96% with the addition of only 0.05 wt% β‐NA. Under non‐isothermal crystallization the content of β‐iPP increases with increasing cooling rate. The maximum β‐crystal content is obtained at a cooling rate of 40 °C min^–1. The supermolecular structure of the β‐iPP is identified as a leaf‐like transcrystalline structure with an ordered lamellae arrangement perpendicular to the special surface of β‐NA. Under isothermal crystallization β‐crystals can be formed in the temperature range 80–140 °C. The content of β‐crystals reaches its maximum value at a crystallization temperature of 130 °C. © 2012 Society of Chemical Industry     

A novel highly efficient β‐nucleating agent for isotactic polypropylene

A novel highly efficient β‐nucleating agent for isotactic polypropylene (iPP), hexahydrophthalic barium (HHPA‐Ba), was found and its effects on the mechanical properties, the β‐phase content, and crystallization behavior of iPP were investigated, respectively. The results show that the β‐phase content of nucleated iPP (k_β value) can reach 80.2% with 0.4 wt % HHPA‐Ba. The impact strength and crystallization peak temperature of nucleated iPP are greatly increased. Compared with pure iPP, the impact strength of nucleated iPP can increase 2.4 times. Meanwhile, the spherulite size of nucleated iPP is dramatically decreased than that of pure iPP. The Caze method was used to investigate the nonisothermal crystallization kinetics of nucleated iPP and the crystallization active energy was achieved by Kissinger method. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Activity of a β‐nucleating agent for isotactic polypropylene and its influence on polymorphic transitions

The influence of a nonpigmenting β‐nucleating additive in the crystallization of isotactic polypropylene (iPP) is investigated by differential scanning calorimetry and X‐ray diffraction. It is found that this additive induces the formation of a very high level of the trigonal modification of iPP. The crystallization and melting behavior of the nucleated systems are studied as a function of the cooling and heating rates and the control of the final temperature during the cooling process. The nucleating agent exerts an important effect on the crystallization temperatures and the polymorphic transitions of iPP, delaying the β–α recrystallization process through an increase in the stability of the trigonal crystals. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 86: 531–539, 2002     

A highly active and selective β‐nucleating agent for isotactic polypropylene and crystallization behavior of β‐nucleated isotactic polypropylene under rapid cooling

Zinc adipate (Adi‐Zn) was observed to be a highly active and selective β‐nucleating agent for isotactic polypropylene (iPP). The effects of Adi‐Zn on the mechanical properties and the β‐crystals content of nucleated iPP were investigated. The impact strength of iPP nucleated with 0.2 wt % Adi‐Zn was 1.8 times higher than that of neat iPP. In addition, wide‐angle X‐ray diffraction analysis indicated that the content of β‐crystals in nucleated iPP (k_β value) reached 0.973 with 0.1 wt % Adi‐Zn, indicating that Adi‐Zn is a highly active and selective β‐nucleating agent for iPP. Furthermore, fast scanning chip calorimetry (FSC) studies using cooling rates from 60 to 13,800 °C min^?1 revealed that the formation of β‐crystals significantly depended on the cooling rates. At cooling rates below 3000 °C min^?1, only β‐crystals existed. However, at cooling rates above 6000 °C min^?1, β‐crystals failed to form. Moreover, a lower critical crystallization temperature that corresponded to the generation of β‐crystals was investigated using cooling‐induced crystallization, and the results are in good agreement with those of a previous study. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43767.     

Highly active thermally stable β‐nucleating agents for isotactic polypropylene

Calcium salts of suberic (Ca‐Sub) and pimelic (Ca‐Pim) acids were synthesized and implemented as in different grades of isotactic polypropylene (iPP). Propylene homopolymer, as well as random and block copolymers containing these additives, crystallized iPP into pure or nearly pure β modification in the isothermal and nonisothermal crystallization experiments. Recently, Ca‐Sub proved to be the most effective β‐nucleating agent of iPP. The Ca‐Sub nucleating agent widens the upper crystallization temperature range of pure β‐iPP formation up to 140°C. In this study the effect of the these additives on the crystallization, melting characteristics, and structure of the PP were studied. The degree of crystallinity of β‐iPP was markedly higher than that of α‐iPP. A widening in the melting peak of the samples crystallized in a high temperature range was first observed and discussed in regard to literature results of the same phenomenon for α‐iPP. The morphology of the β‐iPP samples was revealed by scanning electron microscopy. Independent of the type of polymer or nucleating agent, hedritic structures were found in the early stages of growth of the β‐spherulites. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 74: 2357–2368, 1999     

Variation of non‐isothermal crystallization behavior of isotactic polypropylene with varying β‐nucleating agent content

The non‐isothermal crystallization behavior, the crystallization kinetics, the crystallization activation energy and the morphology of isotactic polypropylene (iPP) with varying content of β‐nucleating agent were investigated using differential scanning calorimetry (DSC) and scanning electron microscopy (SEM). The DSC results showed that the Avrami equation modified by Jeziorny and a method developed by Mo and co‐workers could be successfully used to describe the non‐isothermal crystallization process of the nucleated iPPs. The values of n showed that the non‐isothermal crystallization of α‐ and β‐nucleated iPPs corresponded to a tridimensional growth with homogeneous and heterogeneous nucleation, respectively. The values of crystallization rate constant showed that the rate of crystallization decreased for iPPs with the addition of β‐nucleating agent. The crystallization activation energy increased with a small amount (less than 0.1 wt%) of β‐nucleating agent and decreased with higher concentration (more than 0.1 wt%). The changes of crystallization rate, crystallization time and crystallization activation energy of iPPs with varying contents of β‐nucleating agent were mainly determined by the ratio of the content of α‐ and β‐phase in iPP (α‐PP and β‐PP) from the DSC investigation, and the large size and many intercrossing lamellae between boundaries of β‐spherulites for iPPs with small amounts of β‐nucleating agent and the small size and few intercrossing bands among the boundaries of β‐spherulites for iPPs with large amounts of β‐nucleating agent from the SEM examination. Copyright © 2010 Society of Chemical Industry     

Effect of nucleating duality on the formation of γ‐phase in a β‐nucleated isotactic polypropylene copolymer

BACKGROUND: It is a challenge for polymer processing to promote the formation of γ‐phase under atmospheric conditions in isotactic polypropylene (iPP) copolymer containing chain errors. Incorporation of an α‐nucleator in iPP copolymer seems reasonable since it can enhance non‐isothermal crystallization. Up to now, however, the issue regarding a β‐nucleated iPP copolymer still remains unclear, which is the subject of this study. RESULTS: The results indicate that the γ‐phase indeed occurs in a β‐nucleated random iPP copolymer with ethylene co‐unit (PPR) sample and becomes predominant at slow cooling rates (e.g. 1 °C min^?1) where the formation of the β‐form is suppressed to a large extent. With detailed morphological observations the formation of γ‐phase in the β‐nucleated PPR sample at slow cooling rate is unambiguously attributed to the nucleating duality of the β‐nucleator towards α‐ and β‐polymorphs. The α‐crystals, induced by the β‐nucleator, serve as seeds for the predominant growth of the γ‐phase. Moreover, the presence of the β‐nucleator, acting as heterogeneous nuclei, promotes the formation of γ‐phase in the nucleated PPR sample, at least to some extent. CONCLUSION: The findings in this study extend our insights into the formation of γ‐phase in β‐nucleated iPP copolymer and, most importantly, provide an alternative route to obtain iPP rich in γ‐phase. Copyright © 2008 Society of Chemical Industry     

Combined effect of β‐nucleating agent and processing melt temperature on the toughness of impact polypropylene copolymer

The phase morphology and toughening behavior of impact polypropylene copolymer (IPC) with and without nucleating agent (NA), prepared at different processing melt temperatures (T_p), were investigated. Interestingly, three different structures can be formed in the IPC samples by adding NA or tuning T_p. A well‐defined core–shell structure is obtained in samples with α‐NA or without NA prepared at all T_p. A developing multilayered structure is mainly formed at high T_p with added β‐NA, while an incomplete phase separation structure with interpenetrating chains is the dominant structure for IPC samples prepared at low T_p with added β‐NA. In this case, because of the synergistic effect between phase morphology and relatively high β‐form crystal content, the chain interaction among the components and chain mobility of the amorphous portion of IPC are distinctly improved, resulting in a largely improved toughness under 0 °C. This improvement in toughness is very important for applications. © 2012 Society of Chemical Industry     

Influence of a novel β‐nucleating agent on the structure,morphology, and nonisothermal crystallization behavior of isotactic polypropylene

The crystalline structure, morphology, and nonisothermal crystallization behavior of isotactic polypropylene (iPP) with and without a novel rare earth‐containing β‐nucleating agent (WBG) were investigated with wide‐angle X‐ray diffraction, polar optical microscopy, and differential scanning calorimetry. WBG could induce the formation of the β form, and a higher proportion of the β form could be obtained by the combined effect of the optimum WBG concentration and a lower cooling rate. The content of the β form could reach more than 0.90 in a 0.08 wt % WBG nucleated sample at cooling rates lower than 5°C/min. Polar optical microscopy showed that WBG led to substantial changes in both the morphological development and crystallization process of iPP. At all the studied cooling rates, the temperature at which the maximum rate of crystallization occurred was increased by 8–11°C in the presence of the nucleating agent. An analysis of the nonisothermal crystallization kinetics also revealed that the introduction of WBG significantly shortened both the apparent incubation period for crystallization and the overall crystallization time. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

A novel highly efficient β‐nucleating agent for polypropylene using nano‐CaCO3 as a support

In order to increase the isotactic content of β‐nucleated polypropylene (β‐iPP) and decrease the cost of its production, the investigation and development of novel highly efficient β‐nucleators are important issues. Nano‐CaCO₃ was used as a support to prepare a supported β‐nucleator, nano‐CaCO₃‐supported calcium pimelate. Fourier transform infrared spectral analysis shows that an in situ chemical reaction takes place between nano‐CaCO₃ and pimelic acid. Differential scanning calorimetry results indicate that the crystallization and melting temperatures of β‐phase in supported β‐nucleator‐nucleated iPP are higher than those of calcium pimelate‐nucleated iPP. The β‐nucleating ability of the supported β‐nucleator is little influenced by the cooling rate and crystallization temperature over a wide range. The decreased content of pimelic acid in the supported β‐nucleator slightly decreases the crystallization temperature of iPP but it has no influence on the content of β‐phase in nucleated iPP. A novel supported β‐nucleator has been successfully synthesized via pimelic acid supported on the surface of CaCO₃. The crystallization temperature of iPP and melting temperature of β‐phase in iPP nucleated using the supported β‐nucleator are higher than those of iPP nucleated using calcium pimelate. The concept of a supported nucleator will provide a new way to increase the efficiency of polymer additives and to decrease the amounts of them that need to be used by using nanoparticles as supports. Copyright © 2010 Society of Chemical Industry     

Controllable reinforcement of stiffness and toughness of polypropylene via thermally induced self‐assembly of β‐nucleating agent

An easy approach was reported to achieve the simultaneous reinforcement and toughening of polypropylene (PP) via thermally induced self‐assembly of β‐nucleating agent (TMB‐5). The results showed that the processing temperatures dictated the solubility and self‐assembly of TMB‐5 in the polymer melts to determine the subsequent morphology development of PP. At low processing temperature, TMB‐5 did not dissolve into the polymer melt but remained original shape to induce PP to crystallize into spherulites so that it only promoted the formation of β‐form crystals to enhance the toughness of the samples. At high processing temperature, TMB‐5 gradually dissolved into the polymer melts. On cooling, the dissolved nucleating agent self‐assembled into high aspect ratio fibrils through intermolecular hydrogen‐bonding interactions. Due to a favorable matching between PP and TMB‐5, PP preferred to nucleate and grow orthogonally to the fibril axis and into oriented hybrid shish‐kebab morphology with rich β‐form crystals. Compared with isotropic spherulites, the anisotropic structure exhibited excellent properties of the β‐form crystal and shish‐kebab morphology to simultaneously improve the strength and toughness of TMB‐5‐modified PP samples. With the increasing processing temperature, more dissolved TMB‐5 was involved in the self‐assembly procedure to generate longer fibrils and induce more lamellae to grow on the surface. As a consequence, the anisotropy of the PP samples increased further, bringing out more improvements of the tensile strength. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40605.     

A highly efficient β‐nucleating agent for impact‐resistant polypropylene copolymer

In this work, we reported calcium tetrahydrophthalate as a high efficient β‐nucleating agent (β‐NA) for impact‐resistant polypropylene copolymer (IPC). The relative fraction of the β‐crystal can reach as high as 93.5% when only 0.03% β‐NA is added. The non‐isothermal and isothermal crystallization behaviors, morphology, lamellar structure and mechanical properties of IPCs with various β‐NA contents were studied. During non‐isothermal crystallization, the cooling rate has an important influence on the relative fraction of the β‐crystal, which decreases remarkably as the cooling rate increases. The β‐NA also greatly accelerates crystallization rate of IPC, resulting from both more crystal nuclei and larger Avrami exponent. The small angle X‐ray scattering characterization shows that more amorphous components are included into the inter‐lamellae after addition of β‐NA. Dynamical mechanical analysis (DMA) reveals that the storage modulus at low temperature and the loss factor above 0 °C from the PP component can be enhanced upon addition of β‐NA and reach a maximum at the β‐NA content of 0.05 wt %. Impact test shows that the impact strength of the IPC at 0°C can be improved as much as 40% when the content of calcium tetrahydrophthalate is 0.10 wt %. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40753.     

Mechanical and thermal characteristics and morphology of polyamide 6/isotactic polypropylene blends in the presence of a β‐nucleating agent

The mechanical and thermal characteristics and morphology of polyamide 6 (PA6)/isotactic polypropylene (iPP) blends (10/90 w/w) prepared with different processing procedures and incorporated with an aryl amide nucleating agent, a kind of β‐nucleating agent (β‐NA) for iPP, were investigated. The yield strength and flexural modulus of the blends decreased as β‐NA was introduced into the blends, whereas the impact strength and elongation at break improved. The crystalline structures of the blends closely depended on (1) the processing conditions and (2) competition between the β‐nucleating effect of β‐NA and the α‐nucleating effect of PA6 for iPP. Scanning electron microscopy, differential scanning calorimetry, and X‐ray diffraction were adopted to reveal the microstructures of the blends. At a low β‐NA content (<0.1 wt %), the α‐phase iPP dominated the blends, whereas the relative content of the β‐phase iPP increased remarkably when the β‐NA content was not less than 0.1 wt %. The processing conditions also showed profound influences on the supermolecular structures of iPP; this resulted in different mechanical properties of the blends. As for PA6, the crystallization behavior and crystalline structure did not exhibit obvious changes, but PA6 did play an important role in the epitaxial crystallization of iPP on PA6. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Effect of polystyrenes with different architectures on the β‐nucleating efficiency and toughening of isotactic polypropylene

The effect of polystyrenes (PSs) with different architectures (three‐arm star‐shaped polystyrene (sPS), comb‐like branched polystyrene (cPS) and linear polystyrene) on their β‐nucleating efficiency for isotactic polypropylene (iPP) during crystallization and final impact and the tensile properties of iPP/PS blends were investigated by dynamic rheological measurements, SEM, DSC, polarized optical microscopy, wide angle X‐ray diffraction and mechanical property measurements. The results show that the architecture of PS has marked influence on its dispersibility in iPP and β‐nucleating efficiency. For iPP/cPS blend, plenty of short side chains reduce the probability of cPS chain entanglements, facilitating the interdiffusion between iPP and cPS chains. A favorable interfacial interaction results in good dispersibility, high β nucleating efficiency and an excellent toughening effect of cPS on iPP. However, the relatively high chain entanglement degree of sPS may not be in favor of chain diffusion between iPP and sPS and therefore relatively poor dispersibility and toughening effect are obtained. The elongation at break and impact strength of iPP were dramatically improved, especially with the addition of 1 wt% cPS. The toughening mechanism of PS on iPP is the dissipated energy caused by cavitation and the β‐nucleating effect of PS. © 2018 Society of Chemical Industry     

Effect of syndiotactic polystyrene on the crystallization behavior of isotactic polypropylene/syndiotactic polystyrene blends with and without β‐nucleating agent

Blends of isotactic polypropylene (PP) and syndiotactic polystyrene (sPS) with and without β‐nucleating agent were prepared using a twin‐screw extruder at 290 °C. Blends of PP/sPS with β‐nucleating agent mainly show β crystalline form, irrespective of high (20 °C min^?1) or low (2 °C min^?1) previous cooling rates. This suggests that the cooling rates have little effect on the polymorphic composition of PP in PP/sPS blends. The effect of sPS on the crystallization of PP is compared with that of polyamide 6 (PA6). The increase in crystallization temperature of PP is smaller in the presence of sPS than in the presence of PA6; the fold surface free energy of PP/sPS is larger than that of PP/PA6 blends. These results reveal that compared with PA6, sPS has much weaker α‐nucleation effect on the crystallization of PP. The weak α‐nucleation effect of sPS is attributed to the high lattice mismatch between PP and sPS crystals.     

Simultaneously improving tensile strength and toughness of melt‐spun β‐nucleated isotactic polypropylene fibers

Polymer processing methods generally play a crucial role in determining the development of microstructure in the fabricated product. In this study, isotactic polypropylene (iPP) melt containing 0.05 wt % β‐nucleating agent (β‐NA) was extruded via a melt flow rate indicator. The molten extrudate was stretched into a fiber upon various take‐up velocities (TVs). The microstructures of the fiber were investigated by differential scanning calorimeter, two‐dimensional wide‐angle X‐ray diffraction, and small‐angle X‐ray scattering. Also, its tensile properties (including tensile strength, modulus, elongation at break, and toughness) were measured by tensile test. Interestingly, the tensile strength (135.0 MPa) of a melt‐spun β‐nucleated iPP fiber fabricated at 400 cm/min was enhanced by 115.2%, compared with that (62.7 MPa) prepared at 100 cm/min, with a considerable increment in toughness (from 661 to 853 MJ/m³). The enhancement mechanism for tensile properties was discussed based on the microstructures. This work offers a simple approach to prepare β‐nucleated iPP fibers with excellent strength and toughness. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43454.     

Isothermal crystallization and melting behavior of polypropylene with lanthanum complex of cyclodextrin derivative as a β‐nucleating agent

A novel highly active β‐nucleating agent, β‐cyclodextrin complex with lanthanum (β‐CD‐MAH‐La), was introduced to isotactic polypropylene (iPP). Its influence on isothermal crystallization and melting behavior of iPP was investigated by differential scanning calorimeter (DSC), wide‐angle X‐ray diffraction (WAXD), and polarized light microscopy (PLM). WAXD results demonstrated that β‐CD‐MAH‐La was an effective β‐nucleating agent, with β‐crystal content of iPP being strongly influenced by the content of β‐CD‐MAH‐La and the isothermal crystallization temperature. The isothermal crystallization kinetics of pure iPP and iPP/β‐CD‐MAH‐La was described appropriately by Avrami equation, and results revealed that β‐CD‐MAH‐La promoted heterogeneous nucleation and accelerated the crystallization of iPP. In addition, the equilibrium melting temperature (T) of samples was determined using linear and nonlinear Hoffman‐Weeks procedure. Finally, the Lauritzen‐Hoffman secondary nucleation theory was applied to calculate the nucleation parameter (K_g) and the fold surface energy (σ_e), the value of which verify that the addition of β‐CD‐MAH‐La reduced the creation of new surface for β‐crystal and then led to faster crystallization rate. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Crystalline morphology and mechanical properties of isotactic polypropylene composites filled by wollastonite with β‐nucleating surface

Wollastonite‐filled α‐isotactic polypropylene (iPP) and β‐iPP were prepared through introduction of wollastonite (W) and wollastonite with β‐nucleating surface (W_x) in iPP matrix. The α‐ and β‐nucleating ability of wollastonite, crystalline morphology, and mechanical properties of injected iPP filled by wollastonite with different nucleating surface were compared using differential scanning calorimetry, wide‐angle X‐ray diffraction, polarizing optical microscopy, mechanical testing, and scanning electron microscopy. The results indicated that iPP filled by wollastonite with different nucleating surface has different crystalline morphology, melting behavior, and mechanical properties. The W and W_x filled iPP mainly formed α‐ and β‐phase iPP, respectively. The tensile and flexural modulus of iPP/W and iPP/W_x increased with increasing wollastonite content, and the tensile and flexural modulus of iPP/W_x were lower than that of iPP/W. The tensile property, flexural property, and impact strength of iPP/W_x were higher than that of iPP/W and β‐iPP. The synergistic effect of reinforcing of wollastonite and toughening of β‐phase leads to higher mechanical properties. POLYM. COMPOS., 35:1445–1452, 2014. © 2013 Society of Plastics Engineers     

Influence of different β‐nucleating agent on crystallization behavior,morphology, and melting characteristic of multiwalled carbon nanotube‐filled isotactic polypropylene nanocomposites

To obtain isotactic polypropylene (iPP) nanocomposites with high β‐crystal content, TMB5, calcium pimelate and calcium pimelate supported on the surface of nano‐CaCO₃ were used as β‐nucleating agent and MWCNT filled β‐nucleated iPP nanocomposites were prepared. The effect of different β‐nucleating agent and MWCNT on the crystallization behavior and morphology, melting characteristic and β‐crystal content of β‐nucleated iPP nanocomposites were investigated by DSC, XRD and POM. The results indicated that addition of MWCNT increased the crystallization temperature of iPP and MWCNT filled iPP nanocomposites mainly formed α‐crystal. The β‐nucleating agent can induce the formation of β‐crystal in MWCNT filled iPP nanocomposites. The β‐nucleating ability and β‐crystal content in MWCNT filled β‐nucleated iPP nanocomposites decreased with increasing MWCNT content and increased with increasing β‐nucleating agent content due to the nucleation competition between MWCNT and β‐nucleating agents. It is found that the calcium pimelate supported on the surface of inorganic particles as β‐nucleating agent has stronger heterogeneous β‐nucleation than calcium pimelate and TMB5. The MWCNT filled iPP nanocomposites with high β‐crystal content can be obtained by supported β‐nucleating agent. POLYM. COMPOS., 36:635–643, 2015. © 2014 Society of Plastics Engineers     

Structural characterization of α‐ and β‐nucleated isotactic polypropylene

Modification of isotactic polypropylene (iPP) with two nucleation agents, namely 1,3:24‐bis(3,4‐dimethylobenzylideno) sorbitol (DMDBS) (α‐nucleator) and N, N′‐dicyclohexylo‐2,6‐naphthaleno dicarboxy amide (NJ) (β‐nucleator), leads to significant changes of the structure, morphology and properties. Both nucleating agents cause an increase in the crystallization temperature. The efficiency determined in a self‐nucleation test is 73.4 % for DMDBS and 55.9 % for NJ. The modification with NJ induces the creation of the hexagonal β‐form of iPP. The addition of DMDBS lowers the haze of iPP while the presence of NJ increases the haze. Copyright © 2004 Society of Chemical Industry