Efficiency above 6% in poly(3‐hexylthiophene):phenyl‐C‐butyric acid methyl ester photovoltaics via simultaneous addition of poly(3‐hexylthiophene) based grafted graphene nanosheets and hydrophobic block copolymers

A combination of reduced graphene oxide (rGO) nanosheets grafted with regioregular poly(3‐hexylthiophene) (P3HT) (rGO‐g‐P3HT) and P3HT‐b‐polystyrene (PS) block copolymers was utilized to modify the morphology of P3HT:[6,6]‐phenyl‐C71‐butyric acid methyl ester (PC71BM) active layers in photovoltaic devices. Efficiencies greater than 6% were acquired after a mild thermal annealing. To this end, the assembling of P3HT homopolymers and P3HT‐b‐PS block copolymers onto rGO‐g‐P3HT nanosheets was investigated, showing that the copolymers were assembled from the P3HT side onto the rGO‐g‐P3HT nanosheets. Assembling of P3HT‐b‐PS block copolymers onto the rGO‐g‐P3HT nanosheets developed the net hole and electron highways for charge transport, thereby in addition to photoluminescence quenching the charge mobility (μ_h and μ_e) values increased considerably. The best charge mobilities were acquired for the P3HT₅₀₀₀₀:PC71BM:rGO‐g‐P3HT₅₀₀₀₀:P3HT₇₀₀₀‐b‐PS₁₀₀₀ system (μ_h = 1.9 × 10^?5 cm² V^–1 s^–1 and μ_e = 0.8 × 10^?4 cm² V^–1 s^–1). Thermal annealing conducted at 120 °C also further increased the hole and electron mobilities to 9.8 × 10^?4 and 2.7 × 10^?3 cm² V^–1 s^–1, respectively. The thermal annealing acted as a driving force for better assembly of the P3HT‐b‐PS copolymers onto the rGO‐g‐P3HT nanosheets. This phenomenon improved the short circuit current density, fill factor, open circuit voltage and power conversion efficiency parameters from 11.13 mA cm^?2, 0.63 V, 62% and 4.35% to 12.98 mA cm^?2, 0.69 V, 68% and 6.09%, respectively. © 2019 Society of Chemical Industry     

Preparation of porous poly(3‐hexylthiophene) by freeze‐dry method and its application to organic photovoltaics

Poly(3‐hexylthiophene)(P3HT) with a microporous network structure was prepared from a 1% p‐xylene solution by freeze‐dry method. Scanning electron microscopy (SEM) showed P3HT molecules formed swollen gel‐like structures with different extent of compactness depending on the length of the aggregation period. Absorption spectrum of this P3HT film showed a characteristic peak at 620 nm, which indicated a high degree of order between polymer chains. Photoluminescence (PL) of this highly ordered P3HT film appeared at 712 nm revealing large extent of π–π stacking between P3HT molecules in the freeze‐dry film. Both absorption and photoluminescence results indicated that the original aggregated states of P3HT molecules in gel form had been preserved throughout the freeze‐dry operation. X‐ray diffraction of the annealed samples showed a strong characteristic peak for the side chain aggregation at 2θ = 5.1°, which proved that the freeze‐dry film was with highly order structure. The interconnected and highly ordered P3HT film is used in the study of organic photovoltaics (OPV) after applying an n‐type semiconductor to the surface of the dry porous fibers. A prototype OPV device with power conversion efficiency of 1.47% was prepared by this method. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011.     

Synthesis and characterization of poly(3‐hexylthiophene)–poly(3‐hexyloxythiophene) random copolymers with tunable band gap via Grignard metathesis polymerization

A series of 3‐substituted polythiophene copolymers having different side chain arrangements of hexyl and hexyloxy groups has been synthesized via the Grignard metathesis (GRIM) method and systematically studied. Despite differences in monomer reactivity ratios for the nickel‐catalyzed chain transfer polymerization, random sequences of hexyl‐ and hexyloxy‐substituted polythiophenes with different monomer compositions and adjustable band‐gap energies can be synthesized according to their respective comonomer feed ratio, as evidenced from NMR, UV, electrochemical measurements, and computational calculations. Structural characterization from X‐ray diffraction measurements reveals that the flexible hexyloxy side chains of the monomer significantly affect the crystallinity and molecular packing of the random copolymers. This study shows potential for synthesizing random copolymers with different monomer reactivities via the GRIM method for future optoelectronic applications. © 2014 Society of Chemical Industry     

Effect of the regioregularity of poly(3‐hexylthiophene) on the performances of organic photovoltaic devices

BACKGROUND: The highest efficiencies of bulk‐heterojunction solar cells from poly(3‐hexylthiophene) (P3HT) and [6,6]‐phenyl C₆₁‐butyric acid methyl ester (PCBM) reported so far are close to 6%. Phenomena occurring during the photovoltaic process, such as the creation, diffusion and separation of excitons, as well as charge carrier transport, are governed by the active layer morphology. The latter phenomenon, which depends on the self‐organization of P3HT, can be influenced by its degree of regioregularity. The aim of this work is to clarify the relationship between the regioregularity of P3HT, the composition of P3HT/PCBM blends and the performances of photovoltaic devices. RESULTS: Two types of P3HTs with different degrees of regioregularity have been synthesized and used as active layers with PCBM in photovoltaic cells. The higher performances in photovoltaic devices are obtained for high‐regioregular P3HT and can be explained considering the self‐organizing properties of high‐regioregular P3HT, leading to higher sunlight absorption and higher hole mobilities. In addition, this report demonstrates the importance of the ratio of P3HT versus PCBM in correlation with the regioregularity of P3HT on the optical properties, charge transport and characteristics of photovoltaic cells. CONCLUSION: We have investigated the dependence of the photovoltaic properties of P3HT/PCBM blend‐based photovoltaic devices on the degree of regioregularity of P3HT. We find that the best performance is exhibited by devices based on highly regioregular P3HT. Also, the best performances are not obtained for the same P3HT:PCBM weight ratios for high‐regioregular P3HT (1:0.8) and low‐regioregular P3HT (1:3). Copyright © 2007 Society of Chemical Industry     

Functionalization of multi‐walled carbon nanotubes with poly(ε‐caprolactone) using click chemistry

Multi‐walled carbon nanotubes (MWNTs) were covalently functionalized with poly(ε‐caprolactone) (PCL) using click chemistry. First, chlorine moiety‐containing PCL was synthesized by the copolymerization of α‐chloro‐ε‐caprolactone with ε‐caprolactone monomer using ring opening polymerization, and further converted to azide moiety‐containing PCL. The alkyne‐functionalized MWNTs were prepared with the treatment of p‐amino propargyl ether using a solvent free diazotization procedure. The covalent functionalization of alkyne‐derived MWNTs with azide moiety‐containing PCL was accomplished using Cu(I)‐catalyzed [3+2] Huisgen dipolar cycloaddition click chemistry. The PCL‐functionalization of MWNTs was confirmed by the measurements of Fourier transform infra‐red, NMR, Raman spectroscopy, scanning electron microscopy, and transmission electron microscopy. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Effect of [6,6]‐phenyl‐C61‐butyric acid methyl ester on the morphology of poly(3‐hexylthiophene) film

The change of morphology of poly(3‐hexylthiophene) (P3HT) film as a result of blending with [6,6]‐phenyl‐C₆₁‐butyric acid methyl ester (PCBM) was studied using a freeze‐dry method. A porous structure was observed as the P3HT/PCBM solution was freeze‐dried. The pore size decreased as the proportion of PCBM increased in the P3HT/PCBM blended film. Additionally, the freeze‐dried P3HT/PCBM film was more resistant to the formation of PCBM crystals than that prepared by a spin‐coating method during the thermal annealing process. Homogeneous distribution of PCBM in the freeze‐dried P3HT/PCBM film was the main reason for the reduction of large PCBM crystal formation. Copyright © 2011 Society of Chemical Industry     

Controlling the morphology of poly(3‐hexylthiophene)/methanofullerene film through a dynamic‐cooling and freeze‐drying process

A dynamic‐cooling and freeze‐drying (DCFD) process has been applied to the fabrication of polymer solar cells. The dynamic‐cooling process allows poly(3‐hexylthiophene) molecules to aggregate in solution into a more organized structure during the cooling process; the freeze‐drying process prevents severe agglomeration of [6,6]‐phenyl‐C₆₁‐butyric acid methyl ester (PCBM) during the solvent removing process. Application of these two processes to the preparation of the poly(3‐hexylthiophene)/methanofullerene photoactive layer results in an enhanced poly(3‐hexylthiophene) aggregation and smaller PCBM agglomerates. Devices fabricated using the DCFD process generate 14% more in current density than those prepared by the spin‐coating process under AM1.5G illumination. © 2015 Society of Chemical Industry     

In situ polymerization of 3‐hexylthiophene with double‐walled carbon nanotubes: Studies on the conductive nanocomposite

Poly(3‐alkylthiophene)s represent a family of conjugated polymers that are soluble and processable, but still retaining the good electrical conductivity of the insoluble parent polymer thiophene ring backbone. Poly(3‐hexylthiophene) (P3HT) is reported to be a best candidate in the family for solar cell applications. In situ polymerization of 3‐hexylthiophene monomer with double‐walled carbon nanotubes (DWCNTs) has been attempted with the aim of addressing two main issues, namely, the interfacial bonding and proper dispersion of the carbon nanotubes in the polymer matrix to get a high‐performing polymer/nanocomposite. Fourier transform infrared spectroscopy, Raman, and X‐ray diffraction studies indicate the physical wrapping of the polymer on the nanotubes in the absence of any ground‐state interaction between them. The ultraviolet–visible measurements also support this view. The photoluminescence quenching indicates the effectiveness of the interface in the formation of the donor–acceptor‐type composite. The impressive conductivity values encourage the utility of the composites as photovoltaic material. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Solvent vapor‐induced self assembly and its influence on optoelectronic conversion of poly(3‐hexylthiophene): Methanofullerene bulk heterojunction photovoltaic cells

Nanoscale‐phase separation of electron donor/acceptor blends is crucial for efficient charge generation and collection in polymer bulk heterojunction photovoltaic cells. We investigated solvent vapor annealing effect of poly(3‐hexylthiophene) (P3HT)/methanofullerene (PCBM) blend on its morphology and optoelectronic properties. The organic solvents of choice for the treatment have a major effect on the morphology of P3HT/PCBM blend and the device performance. Ultraviolet‐visible absorption spectroscopy shows that specific solvent vapor annealing can induce P3HT self‐assembling to form well‐ordered structure; and hence, the absorption in the red region and the hole transport are enhanced. The solvent that has a poor solubility to PCBM would cause large PCBM clusters and result in a rough blend film. By combining an appropriate solvent vapor treatment and post‐thermal annealing of the devices, the power conversion efficiency is enhanced. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Plasma treatment‐induced fluorine‐functionalized multi‐walled carbon nanotubes to modify poly(ethylene terephthalate) obtained via in situ polymerization

The introduction of carbon nanotubes in a polymer matrix can markedly improve its mechanical properties and electrical conductivity, and much effort has been devoted to achieve homogeneous dispersions of carbon nanotubes in various polymers. Our group previously performed successfully fluorine‐grafted modification on the sidewalls of multi‐walled carbon nanotubes (MWCNTs), using homemade equipment for CF₄ plasma irradiation. As a continuation of our previous work, in the present study CF₄ plasma‐treated MWCNTs (F‐MWCNTs) were used as a nanofiller with poly(ethylene terephthalate) (PET), which is a practical example of the application of such F‐MWCNTs to prepare polyester/MWCNTs nanocomposites with ideal nanoscale structure and excellent properties. As confirmed from scanning electron microscopy observations, the F‐MWCNTs could easily be homogeneously dispersed in the PET matrix during the in situ polymerization preparation process. It was found that a very low content of F‐MWCNTs dramatically altered the crystallization behavior and mechanical properties of the nanocomposites. For example, a 15 °C increase in crystallization temperature was achieved by adding only 0.01 wt% F‐MWCNTs, implying that the well‐dispersed F‐MWCNTs act as highly effective nucleating agents to initiate PET crystallization at high temperature. Meanwhile, an abnormal phenomenon was found in that the melt point of the nanocomposites is lower than that of the pure PET. The mechanism of the tailoring of the properties of PET resin by incorporation of F‐MWCNTs is discussed, based on structure–property relationships. The good dispersion of the F‐MWCNTs and strong interfacial interaction between matrix and nanofiller are responsible for the improvement in mechanical properties and high nucleating efficiency. The abnormal melting behavior is attributed to the recrystallization transition of PET occurring at the early stage of crystal melting being retarded on incorporation of F‐MWCNTs. Copyright © 2009 Society of Chemical Industry     

Preparation of a poly(3‐hexylthiophene)‐grafted indium tin oxide/poly(3‐hexylthiopene) composite and its conductivity–temperature characteristics

The temperature–conductivity characteristics of poly(3‐hexylthiophene) (P3HT) composites filled with P3HT‐grafted indium tin oxide (ITO) particles were investigated in this work. The ITO particles were first treated with a silane coupling reagent of 3‐aminopropyltriethoxysilane (APS), and then thiophene rings were introduced through a condensation reaction between the ending amino groups of APS and the carboxylic groups of thiophene‐3‐acetic acid. The composites were prepared by the polymerization filling of the 3‐hexylthiophene (3HT) monomer with the thiophene‐ring‐introduced ITO particles. Elemental analysis, Fourier transform infrared, and X‐ray photoelectron spectroscopy were used to confirm the grafting reaction on the ITO surface. The longer the polymerization time was or the higher the 3HT/ITO feeding ratio was, the more P3HT was grafted. The influence of the grafted amount on the electrical properties of ITO particles was attributed to the wrapping effect formed by the grafted P3HT on the surface of the ITO particles. The conductivity change of the P3HT‐grafted ITO/P3HT composites was proved to be subject to the change in the average gap width of ITO interparticles, which was determined by the filling ratio of P3HT to ITO in the polymerization and the volume expansion effect of a P3HT thin film between neighboring ITO particles during the heating process. In comparison with the ungrafted ITO/P3HT composites, the grafting treatment enhanced the interaction between the particles and polymer matrix, and this was helpful for obtaining a more homogeneous dispersion structure for the composites and thus afforded a higher positive temperature coefficient intensity and better reproducibility. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 1881–1888, 2006     

New piezoelectric damping composites of poly(vinylidene fluoride) blended with clay and multi‐walled carbon nanotubes

Damping materials are used to control mechanical vibrations, and piezoelectric damping composite is a very promising material due to its unique mechanism. In this study, a potential piezoelectric damping composite was developed by simply melt mixing poly(vinylidene fluoride) (PVDF) with small amounts of organic modified montmorillonite (OMMT) and multi‐walled carbon nanotubes (MWCNTs). The piezoelectric, mechanical and electrical properties were investigated using a dynamic mechanical analyser, direct current electrical resistivity measurements, X‐ray diffraction, Fourier transform infrared spectroscopy and the direct quasi‐static d₃₃ piezoelectric coefficient method. It was found that the damping property of PVDF can be greatly improved by adding both MWCNTs and OMMT, and the composite containing 1.9 wt% of MWCNTs and 3 wt% of OMMT showed the best damping property. A model and an approximate calculation were applied to explain the improved damping property. Moreover, similar mechanical properties of PVDF composites were observed in the tensile testing and dynamic mechanical analyser measurements. Copyright © 2012 Society of Chemical Industry     

Nanocomposites of poly(L‐lysine) and single‐walled carbon nanotubes

BACKGROUND: Single‐walled carbon nanotubes have inspired research owing to their promise in a broad range of applications. The dispersion of carbon nanotubes is of key importance for the utilization of this interesting material for various potential applications. RESULTS: A novel and simple method was developed to fabricate polymer composites with single‐walled carbon nanotubes based on a solid‐state reaction, in which the nanotubes were reacted with poly(L ‐lysine) using high‐speed vibration milling. Fourier transform infrared and UV‐visible spectroscopy as well as thermogravimetry were employed to characterize the novel composites. The morphology and the dispersion of the carbon nanotubes were determined using scanning and transmission electron microscopy. CONCLUSION: The resulting composites were dispersable in water and are expected to have great potential for both molecular‐level studies and device applications of nanotubes. Copyright © 2007 Society of Chemical Industry     

Temperature‐conductivity characteristics of the composites consisting of fractionated poly(3‐hexylthiophene) and conducting particles

Poly (3‐hexylthiophene) (P3HT) synthesized by oxidative polymerization was fractionated by molecular weight by using organic solvents. The fraction of higher average molecular weight gave higher regioregularity and conductivity. Composites of the P3HT fraction having the highest molecular weight were prepared by use of the following conducting particles as fillers: titanium carbide (TiC), indium tin oxide (ITO), and carbon black (CB). Temperature‐conductivity profiles of the composites showed that the resistance change with PTC (positive temperature coefficient) effect was strongly influenced by the content and size of conducting particles and the molecular weight of P3HT. Although no significant PTC effect for P3HT‐CB composite and little effect for P3HT‐ITO composite system were observed, the P3HT‐TiC composite containing TiC of 70–80 wt % showed an obvious PTC effect that brought the conductivity change by about four orders of magnitude near the glass transition temperature of P3HT. However, such a remarkable PTC effect was not observed for the P3HT‐TiC composite prepared with the P3HT fraction of low‐molecular weight. It was shown that a good PTC effect could be achieved by the composite consisting of the P3HT of high‐molecular weight and the conducting particles of relatively large size. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 77: 3069–3076, 2000     

Effects of multi‐walled carbon nanotube functionalization on the morphological and mechanical properties of nanocomposite foams based on poly(vinyl chloride)/(wood flour)/ (multi‐walled carbon nanotubes)

Experimental results are presented for nanocomposite foams based on unplasticized poly(vinyl chloride)/(wood flour)/(multi‐wall carbon nanotubes) (PVC/WF/MWCNTs). The nanocomposite samples were prepared in an internal mixer and foamed via a batch processing method using compression molding. Nanoparticles were functionalized by sodium hypochlorite solution, and the functionalization process was monitored by Fourier‐transform infrared spectroscopy. The effects of MWCNTs (both neat and functionalized) and blowing agent concentration on the morphological properties (cell size and cell density) and mechanical properties (tensile and flexural strength) of the foam samples were studied. The results revealed that foam cell sizes decreased and cell densities increased with addition of MWCNTs. The dispersion of nanoparticles in the PVC medium was increased by functionalization, and the morphological properties of the foams containing functionalized nanoparticles were improved. Density of nanocomposite foams decreased more with functionalized MWCNTs as compared to other samples. Chemical blowing agent concentration had no significant effect on sample density. Mechanical properties of the samples were improved by using functionalized MWCNTs in comparison with those of foams without this component. J. VINYL ADDIT. TECHNOL., 18:161–167, 2012. © 2012 Society of Plastics Engineers     

Dispersion of multi‐walled carbon nanotubes in poly(aryl ether ketone) obtained by in situ polymerization

BACKGROUND: Recently, much work has focused on the efficient dispersion of carbon nanotubes (CNTs) throughout a polymer matrix for mechanical and/or electrical matrices. However, CNTs used as enhancement inclusions in a high‐performance polymer matrix, especially in poly(aryl ether ketone) (PAEK), have rarely been reported. Therefore, multi‐walled carbon nanotube (MWNT)‐modified PAEK nanocomposites were synthesized by in situ polymerization of monomers of interest in the presence of pre‐treated MWNTs. RESULTS: This process enabled a uniform dispersion of MWNT bundles in the polymer matrix. The resultant MWNT/PAEK nanocomposite films were optically transparent with significant mechanical enhancement at a very low MWNT loading (0.5 wt%). CONCLUSION: These MWNT/polymer nanocomposites are potentially useful in a variety of aerospace and terrestrial applications, due to the combination of excellent properties of MWNTs with PAEK. Copyright © 2009 Society of Chemical Industry     

All polymer PTC devices: Temperature‐conductivity characteristics of polyisothianaphthene and poly(3‐hexylthiophene) blends

The present article is concerned with the temperature‐conductivity characteristics of blends consisting of polyisothianaphthene (PITN) particles and a soluble poly(3‐hexylthiophene) (P3HT). PITN was synthesized by direct conversion of 1,3‐dihydroisothianaphthene (DHITN) monomer using N‐chlorosuccinimide (NCS) as an oxidation/dehydrogenation reagent. The high conductivity and thermal stability of the doped and dedoped PITN were confirmed. Microscopic investigation by scanning electron microscopy (SEM) showed that the as‐prepared PITN exhibited diversified shapes and sizes, with large rectangular particles having an average size of 2 ～ 5μm and fine round particles ranging from 0.1 to 0.3 μm. The PITN particles were blended with the chemically synthesized P3HT as a high conductivity component to improve the conductivity and simultaneously maintain the positive temperature coefficient (PTC) effect of the original P3HT near its melting point. The temperature‐conductivity characteristics for PITN‐P3HT blends with various PITN contents showed that a blend having both a high conductivity (nearly 3 ～ 4 orders higher than that of the original P3HT) and a good PTC intensity could be obtained with a PITN content of 20 ～ 25%. The different temperature‐conductivity behavior of P3HT blends filled with PITN as compared to other conducting particles, for example, carbon black, was explained by its unique dispersion structure due to a relatively higher adhesive interaction of PITN particles with the P3HT matrix during the precipitation process. The results from heating recycles revealed that the PTC effect of PITN‐P3HT blends was not just related to the conductivity decrease of the P3HT matrix, arising from the conformational change of the conjugated backbone during the melting, but also to the dilution effect of the conducting percolation network due to the mobility of PITN particles induced by the viscosity decrease of the P3HT matrix. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 97: 1848–1854, 2005     

Development,optimization, and characterization of electrospun poly(lactic acid) nanofibers containing multi‐walled carbon nanotubes

Electrospinning of poly (L ‐D ‐lactic acid) (PLA) was investigated with the addition of multi‐walled carbon nanotubes (MWNT) for development of a scaffold for tissue engineering. Through this experiment, it was determined that the optimal concentration of PLA with weight average molecular weight (M_w) 250,000 g/mol is ～20 wt % as indicated by scanning electron microscopy. This concentration produces fibers with no beading or film formation. The preferred solvent system is a combination of chloroform and dimethyl formamide to alleviate the volatile action of chloroform. The optimum processing parameters for PLA are an electric field of 1 kV/cm which was determined by a surface response plot to minimize fiber diameter based on the applied voltage, working distance, and addition of MWNT. Fourier Transform infrared spectroscopy has indicated the removal of the solvent system. With the addition of MWNT, the fiber diameter was drastically reduced by 70% to form fibers with a mean diameter of 700 nm. This is believed to be due to an increased surface charge density for the MWNT/polymer solution. Transmission electron microscopy validated the alignment of the MWNT within the fibers. MWNT loading exhibited an increase in the conductance of the scaffold and the tensile modulus at an optimal loading level of 0.25 wt %. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

Isothermal and nonisothermal crystallization kinetics of poly(ε‐caprolactone)/multi‐walled carbon nanotube composites

Differential scanning calorimeter (DSC) and polarized optical microscopy (POM) have been used to investigate the isothermal and nonisothermal crystallization behavior of poly(ε‐caprolactone) (PCL)/multi‐walled carbon nanotube (MWNT) composites. PCL/MWNT composites have been prepared by mixing the PCL polymer with carboxylic groups containing multi‐walled carbon nanotubes (c‐MWNTs) in tetrahydrofuran solution. Raman spectrum of c‐MWNT indicated the possible presence of carboxylic acid groups at both ends and on the sidewalls of the MWNTs. The TEM micrograph showed that the c‐MWNT is well separated and uniformly dispersed in the PCL matrix. DSC isothermal results showed that the introduction of c‐MWNT into the PCL initiates strongly heterogeneous nucleation, which induced a change of the crystal growth process. The activation energy of PCL significantly decreases by adding 0.25 wt% c‐MWNT into PCL/c‐MWNT composites and then increases as c‐MWNT content increases. The result demonstrates that the addition of c‐MWNT into PCL induces the heterogeneous nucleation at lower c‐MWNT content and then inhibits the polymer chain transportation ability during crystallization at higher c‐MWNT content. In this study, we have also studied the nonisothermal crystallization kinetics and melting behavior of PCL/c‐MWNT composites at various cooling rates. The correlation among isothermal and nonisothermal crystallization kinetics and melting behavior of PCL/c‐MWNT composites can be also discussed. POLYM. ENG. SCI., 46:1309–1317, 2006. © 2006 Society of Plastics Engineers