Structure and properties of polybutadiene/montmorillonite nanocomposites prepared by in situ polymerization

Polybutadiene (PB)/Montmorillonite nanocomposites (NCs) were prepared by in situ polymerization through the anionic polymerization technique. The effects of treating method of organophilic MMT (OMMT), the type of OMMT, and the solvent used in polymerization were studied. The structure and properties of NCs were characterized using X‐ray Diffraction (XRD), transmission electron micrograph (TEM), H‐NMR spectrum, differential scanning calorimetry (DSC), thermogravimetric analysis (TGA), and dynamic mechanical analysis (DMA). The consumption of BuLi was varied with different treating methods. The molecular weight distribution of PB added with OMMT (DK1) was wide, and the molecular weight distribution became narrow when OMMT‐DK1B and DK4 were added. OMMT did not disperse stably in cyclohexane, but could form a homogeneous solution in toluene and xylene. XRD and TEM showed that exfoliated NCs were obtained by in situ polymerization through the anionic polymerization technique. From the H‐NMR spectrum of PB and PB/OMMT NCs, it could be seen that the content of 1, 2 units of PB increased ～100%, while 1, 4 units decreased when 6.2 wt % of OMMT was added. The results of DSC and DMA indicated that T_g and T_dc were increased when compared with those of PB. Both storage modulus and loss modulus were increased with the addition of OMMT, and tan δ was decreased. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 99: 3615–3621, 2006     

Characterization and charge transfer mechanism of PIN–cdse nanocomposites

This paper reports structural, thermal, and temperature‐dependent dielectric properties of polyindole–cadmium selenide (PIN–CdSe) nanocomposites. PIN and its nanocomposites were synthesized via in situ chemical oxidative polymerization method. Samples were characterized by Fourier transform infrared spectroscopy (FT‐IR), X‐ray diffraction (XRD), scanning electron microscopy with energy dispersive X‐ray (SEM/EDX), atomic force microscope, differential scanning calorimetry (DSC) and thermogravimetric analysis (TGA). Dielectric properties were analyzed as a function of temperature. FT‐IR spectroscopy indicated that both N H and aromatic CC bonds were affected more by doping process. Significant structural differences were observed in XRD and SEM analyses of PIN and its nanocomposites. Both XRD and DSC measurements revealed that crystallinity of the PIN increases to a certain degree with increasing doping level. Thermogravimetric analysis showed that addition of CdSe decreased degradation temperature of the PIN. Conductivity measurements investigated by universal power law indicated that the charge transport mechanism of all the samples is consistent with correlated barrier hopping model. POLYM. COMPOS., 37:3057–3065, 2016. © 2015 Society of Plastics Engineers     

Synthesis and characterization of hydroxy‐terminated polyether‐polydimethylsiloxane‐polyether (PE‐PDMS‐PE) triblock oligomers and their use in the preparation of thermoplastic polyurethanes

A series of hydroxy‐terminated polyether‐polydimethylsiloxane‐polyether (α,ω‐dihydroxy‐(PE‐PDMS‐PE)) ABA triblock oligomers were synthesized from silanic fluids and methyl polyallyloxide polyethers. The reaction was a one‐step solventless hydrosilylation reaction with chloroplatinic acid (CPA) catalyst in the presence of heat. These ABA oligomers were characterized via ¹H‐NMR, ¹³C‐NMR, ²⁹Si‐NMR, FT‐IR, and GPC to demonstrate that they exhibit a 100% linear ABA structure with a siloxane Si? O chain in the center and polyether ethylene oxide (EO)/propylene oxide (PO) chains on the two sides terminated by hydroxy groups. The triblock oligomers were used to form thermoplastic polyurethanes (TPUs) using two‐step solventless bulk polymerization. The investigation of triblock oligomers impact on TPUs mechanical properties, thermal performance, surface water repellency, and morphology performance were analyzed by Instron material tester, differential scanning calorimetry (DSC), thermogravimetric analysis (TGA), water contact angles (WCA), scanning electron microscope (SEM), and transmission electron microscope (TEM). DSC and TGA indicated that PE‐PDMS‐PE modified TPUs had a clear lower T_g under ?120°C and the temperature of 50% weight loss was improved from 280 to 340°C. PE‐PDMS‐PE–modified TPU did not have the marked reduction on mechanical properties than pure polyether produced TPU. Tensile strength was maintained at 13 MPa and elongation was maintained at 300%. SEM and TEM were used to investigate the copolymers’ morphology performance and found that all PO PE‐PDMS‐PE had a pseudo‐three phase separation. WCA analysis confirmed that PE‐PDMS‐PE–modified TPU had significantly improved hydrophobic performance because the silicone structure linked into TPU copolymers. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42521.     

Synthesis,characterization, and conductivity studies of polypyrrole/copper sulfide nanocomposites

Nanocomposites of polypyrrole (PPy) containing copper sulfide (CuS) were synthesized by an in situ chemical oxidative polymerization. The nanocomposites were characterized by FTIR, SEM, XRD, DSC, TGA, and conductivity studies. The FTIR spectra ascertained the chemical interlinking of polypyrole with metal sulfide nanoparticles. Morphological analysis showed that the nanoparticles were uniformly covering the entire substrate. The XRD pattern reveals that the nanoparticle incorporated polypyrrole showed a crystalline nature and the crystallinity of the polymer increases with increase in concentration of CuS nanoparticles. From DSC, an increase in glass transition temperature shows the increased orderness in the polymer composite than in the pure polypyrrole. Thermal analysis (TGA) of the composite showed a progressive increase in the thermal stability with increase in content of CuS. The frequency dependent electrical properties (a.c. conductivity) of the nanocomposites were higher than that of polypyrrole. The d.c. electrical conductivity increased with increase in amount of nanoparticles in the polymer matrix. The results obtained for these composites have greater scientific and technological interest. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Synthesis and thermal behavior of poly(methyl methacrylate)/Maghnia bentonite nanocomposite prepared at room temperature via in situ polymerization initiated by a new Ni(II)α‐benzoinoxime complex

Poly(methyl methacrylate) (PMMA) and poly(methyl methacrylate)/clay nanocomposite (PMMA/OBT) were successfully prepared in dioxan at room temperature via in situ radical polymerization initiated by a new Ni(II)α‐ Benzoinoxime complex as a single component in presence of 3% by weight of an organically modified bentonite (OBT) (originated from Maghnia, Algeria) and characterized by FTIR, ¹H‐NMR and viscometry. Mainly intercalated and partially exfoliated PMMA/OBT nanocomposite was elaborated and evidenced by X‐Ray diffraction (XRD) and transmission electron microscopy (TEM). The intrinsic viscosity of PMMA/OBT nanocomposite is much higher than the one of pure PMMA prepared under the same conditions. Differential scanning calorimetry (DSC) displayed an increase of 10°C in the glass transition temperature of the elaborated PMMA/OBT nanocomposite relative to the one of pure PMMA. Moreover, the TGA analysis confirms a significant improvement of the thermal stability of PMMA/OBT nanocomposite compared to virgin PMMA: the onset degradation temperature of the nanocomposite, carried out under nitrogen atmosphere, increased by more than 45°C. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

In situ polymerized nanocomposites of poly(butylene succinate)/Tio2 nanofibers: molecular weight,morphology, and thermal properties

In this study, the nanocomposites of poly(butylene succinate) (PBS) and TiO₂ nanofibers were first synthesized via in situ polymerization. Molecular weight, morphology, and thermal properties of the nanocomposites were characterized. As the weight percentage of TiO₂ nanofibers increased from 0 to 2%, the molecular weight of PBS in the nanocomposites decreased gradually compared with that of pure PBS. In morphology, the nanocomposites were constituted by free PBS and PBS‐grafted TiO₂ nanofibers (PBS‐g‐TiO₂), which were proved by the Fourier transform infrared, scanning electron microscopy (SEM), and transmission electron microscopy. In addition, the SEM demonstrated the strong interfacial interaction and homogeneous distribution between TiO₂ nanofibers and PBS matrix. The thermal properties determined by differential scanning calorimetry and thermogravimetric analysis included the increasing of cold crystallization temperatures, the melting temperatures, and the thermal stability. Besides, the crystallinity and the rate of crystallization of the nanocomposites were enhanced, which were also observed by the X‐ray diffraction. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Dielectric,electrical, and rheological characterization of graphene‐filled polystyrene nanocomposites

A series of nanographene filled polystyrene (GPS) nanocomposites was prepared by in situ polymerization of styrene in the laboratory. The concentration of graphene was changed in the step of 0.25 wt% and a total of eight composites (including control) were prepared to obtain a threshold concentration of graphene. These composites, prepared by in situ polymerization followed by compression moulding, were characterized for their structural (using XRD), morphological (SEM), thermal (DSC, TGA, DTGA), dielectric behavior (ɛ', ɛ''') and DC conductivity. It was observed that the thermal stability as well as electrical and rheological properties of graphene‐polystyrene nanocomposites significantly improved due to the homogeneous dispersion, intercalation and exfoliation of the graphene layers in the Polystyrene matrix. It was also observed that at room temperature dielectric constant (ε′) decreased with increasing concentration of graphene and reached a minimum at a certain filler concentration of 0.25 wt% (PSG025) when frequency is kept constant. Rheological study showed an improvement in the storage modulus (G′) with incorporation of graphene as nanofiller. Loss modulus (G′) and complex viscosity (η*) also increased with increasing graphene weight percentage. Relaxation time also increased at high graphene loading because of the pseudo‐solid like behavior of polymer melt. POLYM. COMPOS., 34:2082–2093, 2013. © 2013 Society of Plastics Engineers     

Synthesis and characterizations of branched poly(butylene succinate) copolymers with 1,2‐octanediol segments

Branched poly(butylene succinate) (PBS) copolymers were synthesized, from succinic acid (SA), 1,4‐butanediol (1,4‐BD), and 1,2‐octanediol (1,2‐OD) through a two‐step process containing esterification and polycondensation, with different mole fractions of 1,2‐OD segments. The branched PBS copolymers were characterized with ¹H‐NMR, differential scanning calorimetry (DSC), wide angle X‐ray diffraction (WAXD), thermogravimetric analysis (TGA), dynamic rheological testing, and tensile properties analysis. The results of DSC and WAXD show that, with the increasing of the 1,2‐OD segments content, the glass transition temperature (T_g), melting temperature (T_m), crystallization temperature (T_c), and the degree of crystallinity (X_c) decrease. While the crystal structure of PBS does not change by introducing 1,2‐OD segments. The results of TGA and dynamic rheological testing indicate that the thermal stability of neat PBS is improved with the addition of 1,2‐OD segments. The incorporation of 1,2‐OD segments has some effects on the rheological properties of PBS, such as complex viscosities (|η*|), storage modulus (G′), and loss modulus (G″). Tensile testing demonstrates that the elongation at break is improved significantly with increasing 1,2‐OD segments content, but without a notable decrease of tensile strength. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Novel polyethylene‐b‐polyurethane‐b‐polyethylene triblock copolymers: Facile synthesis and application

A series of novel polyethylene‐b‐polyurethane‐b‐polyethylene (EUE) triblock copolymers is successfully prepared through a facile route combining the thiol‐ene chemistry, addition polymerization, and coupling reaction. The resulting EUE triblock copolymers are characterized by Nuclear magnetic resonance (¹H NMR), Fourier transform‐infrared spectra (FT‐IR), High temperature gel permeation chromatography (HT‐GPC), Differential scanning calorimetry (DSC), Thermogravimetric analysis (TGA), and Transmission electron microscopy (TEM). In addition, the EUE triblock copolymers have been evaluated as compatibilizers in the polymer blends of thermoplastic polyurethane elastomer (TPU) and high‐density polyethylene (HDPE). The SEM results show that the compatibility of immiscible blends is enhanced greatly after the addition of EUE triblock copolymers. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 42967.     

Effect of neodymium‐doped titanium dioxide nanoparticles on the structural,mechanical, and electrical properties of poly(butyl methacrylate) nanocomposites

Nanocomposites based on neodymium‐doped titanium dioxide (Nd‐TiO₂)/poly(n‐butyl methacrylate) (PBMA) have been prepared by an in situ polymerization of butyl methacrylate monomer with varying concentrations of Nd‐TiO₂ nanoparticles. The resulting nanocomposites have been analyzed by ultraviolet (UV)–Visible spectroscopy, Fourier‐transform infrared spectroscopy (FTIR), X‐ray diffraction (XRD), transmission electron microscopy (TEM), scanning electron microscope (SEM), differential scanning calorimetry (DSC), thermogravimetric analysis, and impedance analyzer (TGA). The results of UV and FTIR spectroscopy have indicated the interaction of nanoparticles with the PBMA matrix. Spherically shaped nanoparticles with an average size of 10–25 nm have been revealed in the TEM and their homogeneous dispersion, and interaction of polymer matrix has been confirmed by SEM and XRD studies. The thermal stability and glass transition temperature of the composites were significantly enhanced by the addition of nanoparticles. The AC conductivity and dielectric properties of nanocomposites have been found to be higher than pure PBMA, and the maximum electrical properties have been observed for 7 wt% composite. The reinforcing nature of the nanoparticles in PBMA has been reflected in the improvement in tensile strength measurements. The result indicated that the tensile strength of nanocomposites have greatly enhanced by the addition of Nd‐TiO₂ nanoparticles whereas the elongation at break decreases with the loading of nanofillers. To understand the mechanism of reinforcement, tensile strength values have been correlated with various theoretical modeling. The research has been found to be promising in the development of novel materials with enhanced tensile strength, dielectric constant, and thermal properties, which may find potential applications in energy storage and nanoelectronic devices. J. VINYL ADDIT. TECHNOL., 25:9–18, 2019. © 2018 Society of Plastics Engineers     

Preparation and characterization of chitosan‐graft‐poly(L‐lactic acid) microparticles

To improve the properties of chitosan (CS) and poly(L‐lactic acid) (PLLA) and obtain fully biodegradable materials, CS‐g‐PLLA copolymers were prepared using 1‐(3‐Dimethylaminopropyl)‐3‐ethylcarbodiimide hydrochloride (EDC)/N‐hydroxyl succinimide (NHS) as a coupling agent. The copolymers were characterized by Fourier transform infrared analysis (FTIR), ¹H nuclear magnetic resonance (¹H NMR), elemental analysis, differential scanning calorimetry (DSC), X‐ray diffraction (XRD) and scanning electron microscopy (SEM). The results obtained by FTIR and ¹H NMR showed that CS and PLLA were grafted successfully via an amide bond. DSC and XRD results showed that the thermal stability of CS had been significantly improved by grafting PLLA to the molecular chains of CS and the crystallinity of the CS‐g‐PLLA copolymers decreased significantly. Elemental analysis showed that the achieved the maximum degree of substitution of PLLA was 60.88%, while the concentration of CS was 2 mg/mL, the PLLA molecular weight was 10,000, and the EDC/NHS ratio was 2:1. Images from SEM demonstrated that the copolymers had a spherical shape and smooth surface. Moreover, the products were well dispersed without any aggregation. POLYM. ENG. SCI., 56:1432–1436, 2016. © 2016 Society of Plastics Engineers     

Sulfonated poly(butylene succinate) as a pseudo‐random copolymer: effect of sulfonate groups on microstructure and thermal behavior

The positional effect of sulfonate groups on poly(butylene succinate) (PBS) microstructure was investigated. In this regard, unsaturated poly(butylene fumarate) (PBF) and poly(butylene succinate‐ran‐fumarate) copolymers, synthesized via esterification/polycondensation reactions, were modified through post‐polymerization modification. The progress of the PBF sulfonation reaction was analyzed via ¹H NMR, dynamic light scattering and field emission SEM. The microstructure and thermal behavior of the functional polyesters were studied through DSC, TGA, elemental analysis and ¹H NMR. Based on the results, the sulfonation reaction of unsaturated polymer chains, which are not experiencing a phase separation, is instantaneous, but sulfonation of the chains that have formed colloidal particles is a time‐consuming process. Surprisingly, the outcomes of ¹H NMR analysis revealed a kind of heterogeneity along the fully sulfonated PBS backbone, similar to what is usually observed for copolymers. This is due to the ability of sulfonate groups to locate in different sites and create various block types. Due to the attraction between sulfonate groups, they tend to attach to the chain such that they provide the greatest number of second type blocks (containing two sulfonate groups). The randomness of sulfonated polymers after the sulfonation reaction was increased compared to that of the corresponding unsaturated copolymers. Increasing the content of sulfonate groups also led to a significant decrease in the thermal resistance (ca 120 °C) and crystallinity, along with a dramatic increase in ash content and T_g (up to 156 °C). © 2018 Society of Chemical Industry     

Preparation and properties of PET/PA6 copolymer/montmorillonite hybrid nanocomposite

From in situ polycondensation, a poly(ethylene terephthalate)/Polyamide 6 copolymer/montmorillonite nanocomposite was prepared, after the treatment of montmorillonite (MMT) with a water soluble polymer. The resulting nanocomposites were characterized by X‐ray diffraction (XRD), differential scanning calorimeter (DSC), nuclear magnetic resonance (NMR), dynamic mechanical analysis (DMA), and transmission electron microscopy (TEM). The results of DSC, ¹H NMR, and DMA proved that the nanocomposite synthesized was PET/PA6 copolymer/MMT nanocomposite, not the PET/PA6 blend/MMT nanocomposite. The results of XRD and TEM proved that the dispersion of MMT was improved observably after the introduction of PA6 molecular chain into PET. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 2512–2517, 2006     

Spinning and characterizations of polypropylene/alkylphosphonic acid treated montmorillonite nanocomposite fiber

Fine and well‐dispersed clay was prepared via the in situ conversion of the dodecylamine intercalant inside the clay gallery to dodecylamino dimethylene diphosphonic acid (DDD), using a Mannich reaction, so as to create a repulsive force that delaminated the clay platelets. The clay structure and morphology were characterized by X‐ray diffraction (XRD), Scanning electron microscopy (SEM), and Transmission electron microscopy (TEM) analysis, which revealed changes in the multilayer stacks. XRD analysis showed that the interlayer spacing was largely expanded by the presence of DDD. SEM and TEM images revealed that DDD containing clay (PMMT), but not that without DDD, exhibited transparency, indicating the extremely fine and well‐dispersed clay. Polypropylene/PMMT nanocomposites containing 2, 4, 6, 8, and 10 wt % PMMT were prepared by melt extrusion. The obtained compounds were each spun into a monofilament fiber using a small scale spinning machine and then characterized by XRD, Differential scanning calorimetry (DSC), and Thermogravimetric analysis (TGA), plus the sonic modulus was evaluated. The XRD results revealed an increase in the β crystallinity peak in fibers loaded with 2–10 wt % PMMT, indicating that PMMT particles were capable of acting as a β‐form nucleating agent. However, only minimal changes in the thermal behavior (T_c) were observed due to the tested samples containing insufficient PMMT content. The mechanical properties, in terms of the tensile strength and sonic modulus value (E), of the polypropylene nanocomposite fibers were higher than those of virgin PP fibers, presumably due to the reinforcement effect of the filled PMMT nanoparticles. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Anionic polymerization and properties of graft copolymers consisting of alternating styrene/maleimide copolymer main chains and polyamide 6 grafts

This article is focused on the synthesis of a new type of graft PA6, which contained alternating styrene/maleimide copolymer main chains and PA6 grafts, by anionic polymerization. The preprepared styrene/maleimide copolymers with acylated caprolactam (ACL) pendants were used as macroactivators for the polymerization of molten ε‐caprolactam (CL). Because of the low activating energy for the initial nucleophilic attack of CL anion on the N‐ACL, the polymerization took place in a few minutes. The macroactivators were characterized by ¹H‐NMR. And the thermal properties, dimensional stability, crystallinity, and solvent resistance ability of the graft PA6 were studied, using DSC, TGA, XRD, water absorption measurement, and solubility experiment. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Thermally and mechanically enhanced epoxy resin‐silica hybrid materials containing primary amine‐modified silica nanoparticles

In this article, a series of hybrid materials consisted of epoxy resin matrix and well‐dispersed amino‐modified silica (denoted by AMS) nanoparticles were successfully prepared. First of all, the AMS nanoparticles were synthesized by performing the conventional acid‐catalyzed sol–gel reactions of tetraethyl orthosilicate (TEOS), which acts as acceded sol–gel precursor in the presence of 3‐aminopropyl trimethoxysilane (APTES), a silane coupling agent molecules. The as‐prepared AMS nanoparticles were then characterized by FTIR, ¹³C‐NMR, and ²⁹Si‐NMR spectroscopy. Subsequently, a series of hybrid materials were prepared by performing in situ thermal ring‐opening polymerization reactions of epoxy resin in the presence of as‐prepared AMS nanoparticles and raw silica (RS) particles (i.e., pristine silica). AMS nanoparticles were found to show better dispersion capability in the polymer matrices than that of RS particles based on the morphological observation of transmission electron microscopy (TEM) study. The better dispersion capability of AMS nanoparticles in hybrid materials was found to lead enhanced thermal, mechanical properties, reduced moisture absorption, and gas permeability based on the measurements of thermo gravimetric analysis (TGA), differential scanning calorimetry (DSC), dynamic mechanical analysis (DMA), and gas permeability analysis (GPA), respectively. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Preparation of syndiotactic polystyrene/montmorillonite nanocomposites via in situ intercalative polymerization of styrene with monotitanocene catalyst

Syndiotactic polystyrene (sPS)/montmorillonite nanocomposites were prepared via in situ intercalative coordination polymerization using mono‐(η⁵‐pentamethylcyclopenta‐ dienyl) tribenzyloxy titanium [Cp*Ti(OBz)₃] complex activated by methylaluminoxanes (MAO) and triisobutylaluminum (TIBA). The influences of polymerization conditions, such as the weight ratio of montmorillonite and styrene, temperature, and monomer concentration, on the preparation of sPS/montmorillonite nanocomposites was investigated. The intercalation spacing in the nanocomposites, as well as the exfoliation of the montmorillonite interlayers, was characterized with wide angle X‐ray diffraction (WAXD) and transmission electron microscopy (TEM). The dispersibility of the nanoscale elements depended on the polymerization conditions and the surfactant treatment. The crystallizability and thermal properties of these nanocomposites were determined by differential scanning calorimetry (DSC) analysis and thermogravimetric analysis (TGA). Experimental results indicated that the degree of crystallinity of the sPS nanocomposite increased with increasing montmorillonite content and with higher T_g and thermal decomposition temperature than pure sPS. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 95: 1412–1417, 2005     

Preparation and properties of unsaturated polyester nanocomposites based on silylated sepiolite nanofibers

The novel surface‐modified sepiolite/unsaturated polyester (sepiolite/UP) nanocomposites were prepared by in situ polymerization. Sepiolite fibers were first organo‐modified by grafting of vinyltriethoxysilane (VTS) containing a double bond onto the surfaces and used as nanofillers. The morphology of sepiolites and nanocomposites were characterized by X‐ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR), scanning electron microscope (SEM), and transmission electron microscope (TEM). Moreover, the thermal properties were determined by thermogravimetric analysis (TGA) and the thermal degradation mechanism was discussed. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Polyaniline with high crystallinity degree: Synthesis,structure, and electrochemical properties

Polyaniline (PANI) with high crystallinity degree was facilely synthesized on the surface of stainless steel net by galvanostatic method. The effect of polymerization current density on the characteristics of morphology and structure had been investigated by field emission scanning electron microscopy (FE‐SEM), Fourier transforms infrared (FTIR), X‐ray photoelectron spectroscopy (XPS), and X‐ray diffraction (XRD). FE‐SEM observations disclosed that PANI was deposited as nanofibers and their diameters decreased with the polymerization current density. FTIR studies revealed that degree of oxidation increased in order PANI‐2 < PANI‐6 < PANI‐10. XPS measurements displayed that PANI polymerized at 6 mA cm^?2 (PANI‐6) exhibited much higher doping level of 77.8%, which favored the conductivity. XRD analysis discovered that the obtained PANI showed high crystallinity degree in which PANI‐6 possessed highest crystallinity degree (X_cr) up to 67%. Electrochemical performances of PANI as electrode materials were studied via cyclic voltammetry. The results presented that PANI‐6 possessed greater discharge capacity and better reversibility. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40827.     

Degradation of graft polymer and blend based on cellulose and poly(L‐lactide)

Degradable polymers were prepared by blending and graft polymerization of cellulose and poly(L‐lactide) (PLLA). The cellulose/poly(L‐lactide) blends and cellulose‐graft‐poly(L‐lactide) polymers were characterized by FTIR, NMR, DSC, and TGA. Wide‐angle X‐ray powder diffraction (WAXD) and degradation tests [by alkaline, phosphate‐buffered saline solution (PBS), and enzyme solution] showed changes in the crystalline structure as a result of degradation. The results indicated that blending and graft polymerization could affect crystallization of the polymers and promote the degradability. The polymers with low degree of crystallinity showed higher degradability. In contrast, enzyme, alkaline, and PBS degradated material decreased rate of polymers degradation. In addition, high levels of PLLA resulted in a decrease in degradation. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 130: 2257–2264, 2013