高温相变蓄热的研究进展

从如下两个方面总结了高温相变蓄热的研究现状：①在高温相变材料(PCM)方面，重点介绍了高温相变材料的一些重要性能及其测量，高温相变材料的封装，高温复合相变材料及高温相变材料的应用；②在传热分析方面，主要介绍了相变过程的数值模拟和相变蓄热系统(LTES)的热力学优化。     

High‐temperature latent heat storage technology to utilize exergy of solar heat and industrial exhaust heat

Latent heat storage (LHS) using phase change materials is quite attractive for utilization of the exergy of solar energy and industrial exhaust heat because of its high‐heat storage capacity, heat storage and supply at constant temperature, and repeatable utilization without degradation. In this article, general LHS technology is outlined, and then recent advances in the uses of LHS for high‐temperature applications (over 100 °C) are discussed, with respect to each type of phase change material (e.g., sugar alcohol, molten salt, and alloy). The prospects of future LHS systems are discussed from a principle of exergy recuperation. In addition, the technologies to minimize exergy loss in the future LHS system are discussed on the basis of the thermodynamic analysis by ‘thermodynamic compass’. Copyright © 2016 John Wiley & Sons, Ltd.     

Numerical simulation of a multi-layer latent heat thermal energy storage system

A computational model for the prediction of the thermal behaviour of a compact multi-layer latent heat storage unit is presented. The model is based on the conservation equations of energy for the phase change material (PCM) and the heat transfer fluid (HTF). Electrical heat sources embedded inside the PCM are used for heat storage (melting) while the flow of an HTF is employed for heat recovery (solidification). Parametric studies are performed to assess the effect of various design parameters and operating conditions on the thermal behaviour of the unit. Results indicate that the average output heat load during the recovery period is strongly dependent on the minimum operating temperature, on the thermal diffusivity of the liquid phase, on the thickness of the PCM layer and on the HTF inlet mass flowrate and temperature. It is, on the other hand, nearly independent of the wall thermal diffusivity and thickness and of the maximum operating temperature. Correlations are proposed for the total energy stored and the output heat load as a function of the design parameters and the operating conditions. © 1998 John Wiley & Sons, Ltd.     

A study on latent heat storage exchangers with the high‐temperature phase‐change material

This paper presents a theoretical analysis and an experimental test on a shell‐and‐tube latent heat storage exchanger. The heat exchanger is used to recover high‐temperature waste heat from industrial furnaces and off‐peak electricity. It can also be integrated into a renewable energy system as an energy storage component. A mathematical model describing the unsteady freezing problem coupled with forced convection is solved numerically to predict the performance of the heat exchanger. It provides the basis for an optimum design of the heat exchanger. The experimental study on the heat exchanger is carried out under various operating conditions. Effects of various parameters, such as the inlet temperature, the mass flow rate, the thickness of the phase‐change material and the length of the pipes, on the heat transfer performance of the unit are discussed combined with theoretical prediction. The criterion for analyzing and evaluating the performance of heat exchanger is also proposed. Copyright © 2001 John Wiley & Sons, Ltd.     

Review on heat transfer analysis in thermal energy storage using latent heat storage systems and phase change materials

Thermal energy storage (TES) is a technology that stocks thermal energy by heating or cooling a storage medium so that the stored energy can be used later for heating and cooling applications and for power generation. TES has recently attracted increasing interest to thermal applications such as space and water heating, waste heat utilisation, cooling, and air conditioning. Phase change materials (PCMs) used for the storage of thermal energy as latent heat are special types of advanced materials that substantially contribute to the efficient use and conservation of waste heat and solar energy. This paper provides a comprehensive review on the development of latent heat storage (LHS) systems focused on heat transfer and enhancement techniques employed in PCMs to effectively charge and discharge latent heat energy, and the formulation of the phase change problem. The main categories of PCMs are classified and briefly described, and heat transfer enhancement technologies, namely dispersion of low‐density materials, use of porous materials, metal matrices and encapsulation, incorporation of extended surfaces and fins, utilisation of heat pipes, cascaded storage, and direct heat transfer techniques, are also discussed in detail. Additionally, a two‐dimensional heat transfer simulation model of an LHS system is developed using the control volume technique to solve the phase change problem. Furthermore, a three‐dimensional numerical simulation model of an LHS is built to investigate the quasi‐steady state and transient heat transfer in PCMs. Finally, several future research directions are provided.     

潜热储热系统强化传热研究进展

近年来,潜热储热系统在太阳能和工业废能的利用中发挥着极其重要的作用,因此用于潜热储热的相变材料受到普遍关注.文章对国内外潜热储热系统众多强化传热技术进行了综述与讨论.     

Numerical simulations on performance enhancement of a cross-flow latent thermal energy storage heat exchanger

基于列管式换热器具有传热面积大、结构紧凑、操作弹性大等优点,使其在相变储能领域具有广阔的应用前景。本文建立一种新型列管式相变蓄热器模型,在不考虑自然对流的情况下,利用Fluent软件对相变蓄热器进行二维储热过程的数值模拟。本文主要研究斯蒂芬数、雷诺数、列管排列方式、肋片数以及相变材料的导热系数对熔化过程的影响,并对熔化过程中固液分界面的移动规律进行了分析。模拟结果表明,内肋片强化换热效果明显,特别是对应用低导热系数相变材料[导热系数小于1 W/(m·K)]的列管式蓄热器,相对于无肋片结构,加入肋片（N_fn=2）可缩短熔化时间52.6%。     

Performance enhancement in latent heat thermal storage system: A review

Phase change material (PCM) based latent heat thermal storage (LHTS) systems offer a challenging option to be employed as an effective energy storage and retrieval device. The performance of LHTS systems is limited by the poor thermal conductivity of PCMs employed. Successful large-scale utilization of LHTS systems thus depends on the extent to which the performance can be improved. A great deal of work both experimental and theoretical on different performance enhancement techniques has been reported in the literature. This paper reviews the implementation of those techniques in different configurations of LHTS systems. The influence of enhancement techniques on the thermal response of the PCM in terms of phase change rate and amount of latent heat stored/retrieved has been addressed as a main aspect. Issues related to mathematical modeling of LHTS systems employing enhancement techniques are also discussed.     

Numerical simulation of high‐temperature phase change heat storage system

In this paper, numerical results pertaining to cyclic melting and freezing of an encapsulated phase‐change material (PCM) have been reported. The cyclic nature of the present problem is relevant to latent heat thermal energy storage system used to power solar Brayton engines in space. In particular, a physical and numerical model of the single‐tube phase change heat storage system was developed. A high‐temperature eutectic mixture of LiF‐CaF₂ was used as the PCM and dry air was used as the working fluid. Numerical results were compared with available experimental data. The trends were in close agreement. © 2003 Wiley Periodicals, Inc. Heat Trans Asian Res, 33(1): 32–41, 2004; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/htj.10132     

A semi-analytical solution for time-varying latent heat thermal energy storage problems

Latent heat thermal energy storage (LHTES) problems include a lot of boundary conditions that could not be solved by exact solution, so new approaches to solving such problems could revolutionize the advanced energy storage devices. This paper focuses on reformulating the generalized differential quadrature method (GDQM) for a one-dimensional solidification/melting Stefan problem as a fundamental LHTES problem and solves some practical cases. Convergence and comparisons demonstrate that the proposed approach is sufficiently reliable. By checking the accuracy of the proposed approach for the LHTES problem (where Stefan number is below 0.2), it was demonstrated that for all Stefan numbers, the maximum error is less than 3.81% for temperatures. As the usual range of thermal energy storages, for Stefan numbers up to 0.2 the solution yields errors less than 0.2%. Then, the proposed approach is very ideal for such applications. In comparison, GDQM has a more accurate response than an integral solution for Stefan numbers less than 0.2. When this priority of GDQM comes with its low computational cost, it would undoubtedly be preferable.     

HVAC领域相变贮能研究的现状与进展

总结了相变传热的特点及求解方法 ;相变墙板的研制以及使用效果方面的研究现状 ;相变在供暖、空调系统中的应用 ;相变贮能技术在HVAC中应用的诸多优势。提出了HVAC领域相变贮能技术今后的研究方向。     

Fatty acid/poly(methyl methacrylate) (PMMA) blends as form-stable phase change materials for latent heat thermal energy storage

Fatty acids such as stearic acid (SA), palmitic acid (PA), myristic acid (MA), and lauric acid (LA) are promising phase change materials (PCMs) for latent heat thermal energy storage (LHTES) applications, but high cost is the most drawback which limits the utility area of them in thermal energy storage. The use of fatty acids as form-stable PCM will increase their feasibilities in practical LHTES applications due to reduced cost of the energy storage system. In this regard, a series of fatty acid/poly(methyl methacrylate) (PMMA) blends, SA/PMMA, PA/PMMA, MA/PMMA, and LA/PMMA were prepared as new kinds of form-stable PCMs by encapsulation of fatty acids into PMMA which acts as supporting material. The blends were prepared at different mass fractions of fatty acids (50, 60, 70, 80, and 90% w/w) to reach maximum encapsulation ratio. All blends were subjected to leakage test by heating the blends over the melting temperature of the PCM. The blends that do not allow leakage of melted PCM were identified as form-stable PCMs. The form-stable fatty acid/PMMA (80/20 wt.%) blends were characterized using optic microscopy (OM), viscosimetry, and Fourier transform infrared (FT-IR) spectroscopy methods, and the results showed that the PMMA was compatible with the fatty acids. In addition, thermal characteristics such as melting and freezing temperatures and latent heats of the form-stable PCMs were measured by using differential scanning calorimetry (DSC) technique and indicated that they had good thermal properties. On the basis of all results, it was concluded that form-stable fatty acid/PMMA blends had important potential for some practical LHTES applications such as under floor space heating of buildings and passive solar space heating of buildings by using wallboard, plasterboard or floor impregnated with a form-stable PCM due to their satisfying thermal properties, easily preparing in desired dimensions, direct usability without needing an add encapsulation and eliminating the thermal resistance caused by shell and thus reducing cost of LHTES system.     

Study on design and thermal characteristics of vacuum tube solar collector intubated with heat storage tube

In this work, a heat storage vacuum tube solar collector intubated with heat storage tube is designed, which consists of solar vacuum tube, phase change material insert tube, and heat holding cover. The internal energy conversion, transmission, and storage theory are established based on the structure of the heat storage vacuum tube. The parallel and series‐parallel solar air collector system prototype consisting of nine heat storage solar vacuum tube solar collectors is designed and tested. The test results showed that the daily average conversion efficiency of the parallel and series‐parallel prototype reached 56.9% and 48.46%, respectively. Compared with nonheat storage prototype, the heat storage parallel and series‐parallel prototype had higher conversion efficiency by, respectively, 10.9% and 7.8%, longer effective heating time, and better heating stability and practicability. At the same time, the heat storage solar collector has compact structure, which is convenient to use.     

Phase change characteristics of ethylene glycol solution‐based nanofluids for subzero thermal energy storage

Nanofluids, particularly water‐based nanofluids, have been extensively studied as liquid–solid phase change materials (PCMs) for thermal energy storage (TES). In this study, nanofluids with aqueous ethylene glycol (EG) solution as the base fluid are proposed as a novel PCM for cold thermal energy storage. Nanofluids were prepared by dispersing 0.1–0.4 wt% TiO₂ nanoparticles into 12, 22, and 34 vol.% EG solutions. The dispersion stability of the nanofluids was evaluated by Turbiscan Lab. The liquid–solid phase change characteristics of the nanofluids were also investigated. Phase change temperature (PCT), nucleation temperature, and half freezing time (HFT) were investigated in freezing experiments. Subcooling degree and HFT reduction were then calculated. Latent heat of solidification was measured using differential scanning calorimetry. Thermal conductivity was determined using the hot disk thermal constant analyzer. Experimental results show that the nanoparticles decreased the PCT of 34 vol.% EG solution but minimally influenced the PCT of 12 and 22 vol.% EG solutions. For all nanofluids, the nanoparticles decreased the subcooling degree, HFT, and latent heat but increased the thermal conductivity of the EG solutions. The mechanism of the improvement of the phase change characteristics and decrease in latent heat by the nanoparticles was discussed. The nanoparticles simultaneously served as nucleating agent that induced crystal nucleation and as impurities that disturbed the growth of water crystals in EG solution‐based nanofluids. Copyright © 2016 John Wiley & Sons, Ltd.     

A model for latent heat energy storage systems

In this study, a theoretical approach is proposed for the prediction of time and temperature during the heat charge and discharge in the latent heat storage of phase changed materials (PCM). By the use of the average values of the mean specific heat capacities for the phase‐changed materials, analytical solutions are obtained and compared with the available experimental data in the literature. It is shown that decreasing the entry temperature of the working fluid from ?4 to ?15°C has a very dominant and strong effect on the PCM solidification time. The effect of the working fluid flow rate and the material of PCM capsules on the time for complete solidification and total charging is also investigated. The agreement between the present theoretical model results and the experimental data related to the cooling using small spheres and the heat storage using rectangle containers is very good. The largest difference between the present results and the experimental data becomes about 10% when the fluid temperature approaches the phase change temperature at high temperatures. Copyright © 2006 John Wiley & Sons, Ltd.     

Solar multi-mode heating system based on latent heat thermal energy storage and its application

为克服太阳能间断性和不稳定性的缺点进而实现太阳能集热与采暖的能量供需调节和全天候连续供热,提出了基于相变储热的太阳能多模式采暖方法（太阳能集热直接采暖、太阳能集热采暖+相变储热、太阳能相变储热采暖）,并在西藏林芝市某建筑搭建了太阳能与相变储热相结合的采暖系统,该系统可根据太阳能集热温度和外界供热需求实现太阳能多模式采暖的自动控制和自动运行。实验研究表明：在西藏地区采用真空管太阳能集热器可以和中低温相变储热器很好地结合,白天储热器在储热过程中平均储热功率为10.63 kW,储热量达到92.67 kW·h,相变平台明显;晚上储热器在放热过程中供热量达85.23 kW·h,放热功率和放热温度平稳,储放热效率达92%,其储热密度是传统水箱的3.6倍,可连续供热时间长达10 h,从而实现了基于相变储热的太阳能全天候连续供热,相关研究结果对我国西藏地区实施太阳能采暖具有一定的指导作用。     

Recapitulation on latent heat hybrid buildings

In the existent paper, the performance of thermal storage hybrid buildings exploiting the latent heat of phase change materials (PCMs) for thermal refrigeration and heating of the contemporary period has been investigated. The conventional buildings consume a large amount of electricity, primarily for the heating and cooling applications. Electricity generation primarily relies on coal-based thermal power plants. The emissions from these establishments pose a serious threat to the environment. Moreover, conventional heating/cooling units rely on exorbitant energy cost. The usage of any kind of thermal storage system is an efficacious way of stockpiling thermal energy and utilizing it when needed. This paper gives a comprehensive overview of the available thermal storage units incorporating PCMs. The various segments of the buildings, viz, ceiling, window, wall, and floor have been analyzed in details. The results are quite promising in terms of load reduction and overall energy saving. Indoor surface temperature reduction of up to 7^oC has been achieved. The energy saving of up to 40% can be realized by employing PCM. A comprehensive list of the PCMs is also tried to build up for end users according to their temperature requirement.     

Microencapsulation of coco fatty acid mixture for thermal energy storage with phase change material

Thermal energy storage systems provide several alternatives for efficient energy use and energy conservation. Microcapsules of natural coco fatty acid mixture were prepared to be used as phase change materials for thermal energy storage. The coacervation technique was used for the microencapsulation process. Several alternatives for the capsule wall material were tried. The microcapsules were characterized according to their geometric profiles, phase transition temperatures, mean particle sizes, chemical stabilities, and their thermal cycling. The diameters of microcapsules prepared in this study were about 1 mm. Coco fatty acid mixtures have kept their geometrical profiles even after 50 thermal cycles for melting and freezing operations in temperature range from 22 to 34°C. It was found that gelatin+gum Arabic mixture was the best wall material for microencapsulating coco fatty acid mixtures. Copyright © 2005 John Wiley & Sons, Ltd.     

Channel formation and visualization of melting and crystallization behaviors in direct-contact latent heat storage systems

Thermal storage systems are an essential component for increasing the share of renewable energies in residential heating and for the valorization of waste heat. A key challenge for the widespread application of thermal storage systems is their limited power-to-capacity ratio. One potential solution for this challenge is represented by direct-contact latent heat storage systems, in which a phase change material (PCM) is in direct contact with an immiscible heat transfer fluid (HTF). To demonstrate the applicability of the direct-contact concept for domestic hot water production, a PCM with a phase change temperature of 59°C is chosen. To enable cost-efficient implementation of the storage system, a eutectic mixture of two salt hydrates, magnesium chloride hexahydrate and magnesium nitrate hexahydrate, is chosen as the PCM. One key aspect for the direct-contact concept is that, during discharge, the HTF channels in the PCM do not become clogged during the solidification of the PCM. In this study, the formation and topology of the channels in direct-contact systems under an optimized flow condition are investigated via visual observation and X-ray computed tomography. The elucidation of the channel structure provides information on the melting and crystallization behaviors of the PCM, which are shown schematically.     

A numerical investigation into the charge behaviour of a spherical phase change material particle for high temperature thermal energy storage in packed beds

基于高温相变材料,对填充床储热系统中储热单元球体的储热性能进行了模拟研究.研究了不同传热流体温度和球体直径对球体储热性能的影响规律,对导热为主的相变储热过程与导热和自然对流共同作用的相变储热过程进行了比较分析,同时还探讨了高温辐射换热的影响.结果表明,相变时间随球体直径的增大而增大,随传热流体温度的增大而减小.当考虑相变区域自然对流时,总的相变时间显著减少,和单纯导热相比,完全相变时间缩短了近16%.在导热和自然对流的基础上加上辐射传热后可以看出,辐射换热强化了球体内的传热过程,加快了相变材料的熔化速度,强化了自然对流的作用.