Influence of the ethylene–(methacrylic acid)–Zn2+ ionomer on the thermal and mechanical properties of blends of poly(propylene) (PP)/ethylene–(vinyl alcohol) copolymer (EVOH)

The thermal and mechanical properties and the morphologies of blends of poly(propylene) (PP) and an ethylene–(vinyl alcohol) copolymer (EVOH) and of blends of PP/EVOH/ethylene–(methacrylic acid)–Zn²⁺ ionomer were studied to establish the influence of the ionomer addition on the compatibilization of PP/EVOH blends and on their properties. The oxygen transmission rate (O₂TR) values of the blends were measured as well. PP and EVOH are initially incompatible as was determined by tensile tests and scanning electronic microscopy. Addition of the ionomer Zn²⁺ led to good compatibility and mechanical behaviour was improved in all blends. The mechanical properties on extruded films were studied for 90/10 and 80/20 w/w PP/EVOH blends compatibilized with 10 % of ionomer Zn²⁺. These experiments have shown that the tensile properties are better than in the injection‐moulded samples. The stretching during the extrusion improved the compatibility of the blends, diminishing the size of EVOH domains and enhancing their distribution in the PP matrix. As was to be expected, the EVOH improved the oxygen permeation of the films, even in compatibilized blends. Copyright © 2004 Society of Chemical Industry     

Rheological behavior and morphological and interfacial properties of PLA/TPE blends

Rheological and interfacial tension data were employed to predict the morphology and thermal and mechanical properties of noncompatibilized and compatibilized poly(lactic acid) (PLA)/thermoplastic elastomer (TPE) blends. PLA was melt blended with thermoplastic polyurethane (TPU) and ethylene elastomer (EE) and compatibilized by ethylene–butyl acrylate–glycidyl methacrylate (EBG) in an internal mixer chamber. Both TPU and EE TPEs have higher viscosities than PLA, and the interfacial properties evaluated have revealed better adhesion between domains of PLA–TPU. The efficiency of the compatibilizer agent EBG depended on the TPE type inferred by modifications in the scanning electron microscopy images of PLA/TPE blends and by the Izod impact strength (improved by 23%). The EBG was more effective in the PLA/TPU blend. The TPEs and EBG did not affect the PLA thermal stability, and no thermal event was observed in the usual PLA extrusion and injection temperature range. © 2019 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2019 , 136, 47962.     

Dynamic mechanical properties of polypropylene–polyamide blends: Effect of compatibilization

The influence of compatibilization on the dynamic mechanical properties of polypropylene (PP) binary blends with polyamide-11 (PA) has been investigated. In the blends an acrylic acid functionized PP was used as a blend component and compared with nonfunctionized PP over the who concentration range. The results demonstrate that the use of the functionized PP instead of the unmodified one produced blends with different dynamic mechanical properties due to adhesion enhancement between the two phases. The storage moduli E′ of the compatibilized blends vary nearly linearly as a function of composition over a broad temperature region, whereas those of the noncompatibilized ones deviate greatly from linearity, specially at about 50/50 ratio, at which a minimum exists at about room temperature. While the dynamic testing gives no evidence for the variation in the glassy transition temperatures (peak maxima) of the components (PP and PA) in the two types of blends, both the loss modulus (E″) and the loss factor (tan δ) data indicate that the compatibilized blends differ from the noncompatibilized ones mainly in the glassy transition (βrelaxation) process of the PA phase, suggesting that the compatibilization of the blends seems to influence the PA phase more than the PP phase included. But, for the β-relaxation behavior of the PA in the modified blends, the tan δ spectrum shows a more complex pattern than does the E″. These results are discussed in terms of the morphological texture of the blends and possible chemical or physical interactions between the two consituent polymers.     

Compatibilization of polypropylene/nylon 6 blends with a polypropylene solid‐phase graft

The compatibilization of polypropylene (PP)/nylon 6 (PA6) blends with a new PP solid‐phase graft copolymer (gPP) was systematically studied. gPP improved the compatibility of PP/PA6 blends efficiently. Because of the reaction between the reactive groups of gPP and the NH₂ end groups of PA6, a PP‐g‐PA6 copolymer was formed as a compatibilizer in the vicinity of the interfaces during the melting extrusion of gPP and PA6. The tensile strength and impact strength of the compatibilized PP/PA6 blends obviously increased in comparison with those of the PP/PA6 mechanical blends, and the amount of gPP and the content of the third monomer during the preparation of gPP affected the mechanical properties of the compatibilized blends. Scanning electron microscopy and transmission electron microscopy indicated that the particle sizes of the dispersed phases of the compatibilized PP/PA6 blends became smaller and that the interfaces became more indistinct in comparison with the mechanical blends. The microcrystal size of PA6 and the crystallinity of the two components of the PP/PA6 blends decreased after compatibilization with gPP. The compatibilized PP/PA6 blends possessed higher pseudoplasticity, melt viscosity, and flow activation energy. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 93: 420–427, 2004     

Influence of a compatibilizer on the properties of polyethylene–octene elastomer/starch blends

The effect of a compatibilizer on the properties of corn starch‐reinforced metallocene polyethylene–octene elastomer (POE) blends was studied. The compatibility between POE and starch was improved markedly with an acrylic acid‐grafted POE (POE‐g‐AA) copolymer as a compatibilizer. Fourier transform infrared spectroscopy, X‐ray diffraction spectroscopy, differential scanning calorimetry, and scanning electron microscopy were used to examine the blends produced. The size of the starch phase increased with an increasing content of starch for noncompatibilized and compatibilized blends. The POE/starch blends compatibilized with the POE‐g‐AA copolymer lowered the size of the starch phase and had a fine dispersion and homogeneity of starch in the POE matrix. This better dispersion was due to the formation of branched and crosslinked macromolecules because the POE‐g‐AA copolymer had anhydride groups to react with the hydroxyls. This was reflected in the mechanical properties of the blends, especially the tensile strength at break. In a comparison with pure POE, the decrease in the tensile strength was slight for compatibilized blends containing up to 40 wt % starch. The POE‐g‐AA copolymer was an effective compatibilizer because only a small amount was required to improve the mechanical properties of POE/starch blends. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 86: 1792–1798, 2002     

Novel approach for the preparation of a compatibilized blend of nylon 11 and polypropylene with polyhydroxybutyrate: Mechanical,thermal, and barrier properties

This article comprises of the interaction in the immiscible polymer system of nylon 11 (PA 11), polypropylene (PP), and polyhydroxybutyrate (PHB). Reactive compatibilization extrusion method with maleic anhydride-grafted polypropylene (PP-g-MA) is used to achieve compatibility within the polymer. To further improve the interaction of the blend at interphase, PHB was added as a dispersive phase in a concentration varying from 10 to 40% of the total batch. Addition of PHB motives the excellent dispersion of PP chain in PA 11 and assures the compatibility between the phases of PA 11 and PP-g-MA. The entire system of tertiary and binary phases was blended in a twin-screw extruder at different composition. The macro-optimal tensile strength, Young's modulus, bending strength, and notched impact strength of PA11/PP systems were found to be superior as compared to their noncompatibilized systems. The degradation temperature of the blends of PA11/PP and PA11/PHB/PP with and without compatibilizer was evaluated by thermogravimetric analysis (TGA). It was found that the high temperature of degradation was required for compatibilized ternary blend than that of the compatibilized binary blend. The distortion temperature of the systems was studied with the help of heat deflection temperature (HDT) and found to be advanced for blend having a higher concentration of the dispersed phase. Differential scanning calorimetry (DSC) was used to determine the % crystallinity, melting, and crystallization temperature of this system. Chemical resistance and barrier properties of the different compatibilized and noncompatibilized blends were studied. PHB dispersed phase with a reactive compatibilizer cause enhancement in chemical resistance and barrier properties of the blend. © 2019 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2019 , 136, 48152.     

CO2 adsorption performance of polyethyleneimine-modified ion-exchange resin

A series of solid amine adsorbents were prepared by the template method with ion-exchange resin (D001) as the carrier and polyethyleneimine (PEI) as the modifier. The absorbents were characterized by energy disperse spectroscopy (EDS), scanning electron microscope (SEM), N₂ adsorption–desorption, Fourier transform infrared spectroscopy (FTIR) and thermogravimetric analysis (TGA) techniques. The effects of PEI loading, adsorption temperature and influent velocities on CO₂ adsorption capacity in a fixed-bed reactor were investigated. The results show that the solid amine adsorbent prepared by the template method had a better PEI dispersion, stability and CO₂ adsorption capacity. The maximum CO₂ adsorption capacity was 3.98 mmol·g^?1 when PEI loading was 30%, the adsorption temperature was 65°C and the influent velocity was 40 mL·min^?1. The CO₂ adsorption capacity decreased only by 9.50% after 10 cycles of adsorption–desorption tests. The study of kinetics indicates that both chemical adsorption and physical adsorption occurred in the CO₂ adsorption process. The CO₂ adsorption process included fast breakthrough adsorption and gradually approaching equilibrium stage. The particle internal diffusion process was the control step for CO₂ adsorption.     

Carbon dioxide capture under postcombustion conditions using amine-functionalized SBA-15: Kinetics and multicyclic performance

ABSTRACT

In this work, ordered mesoporous SBA-15 was synthesized and functionalized by polyethyleneimine (PEI). The morphological properties were characterized by N₂ adsorption/desorption, field–emission scanning electron microscopy (FE-SEM), high–resolution transmission electron microscopy (HR-TEM) and Fourier transform infrared (FTIR) spectroscopy methods. The carbon dioxide (CO₂) uptake on the sorbents, kinetics of CO₂ adsorption/desorption and long-term multicycle stability of PEI-impregnated sorbent were measured. An optimal amine loading of 50 wt.% showed a CO₂ adsorption capacity ~3.09 mmol g^?1 using 10% pre-humidified CO₂ at 75°C. The presence of moisture in flue gas showed a promoting effect in CO₂ sorption capacity. The temperature swing adsorption/desorption cycles showed excellent multicycle stability over 60 cycles during 65 h of operations under humid CO₂.     

The effect of compatibilizers and organically modified nanoclay on the morphology and performance properties of poly(acrylonitrile–butadiene–styrene)/polypropylene blends

In this study, poly(acrylonitrile–butadiene–styrene)/polypropylene (ABS/PP) blends with various compositions were prepared by melt intercalation in a twin‐screw extruder. Modifications of the above blends were performed by using organically modified montmorillonite (OMMT, Cloisite 30B) reinforcement as well as two types of compatibilizers, namely polypropylene grafted with maleic anhydride (PP‐g‐MAH) and ABS grafted with maleic anhydride (ABS‐g‐MAH). Increasing the PP content in ABS matrix seems to increase the melt flow and thermal stability of their blends, whereas a deterioration of the tensile properties was recorded. On the other hand, the addition of ABS to PP promotes the formation of the β‐crystalline phase, which became maximum at 30 wt% ABS concentration, and increases the crystallization temperature (T_c) of PP. A tendency for increase of T_c was also recorded by incorporation of the above compatibilizers, whereas the glass transition temperature (T_g) of PP and SAN phase in ABS was reduced. Regarding the Young's modulus, the greatest improvement was observed in pure ABS/PP blends containing organically modified nanoclay. However, in reinforced pure PP, the use of compatibilizers is recommended in order to improve the elastic modulus. The addition of OMMT to noncompatibilized and compatibilized ABS/PP blends significantly improves their storage modulus. POLYM. ENG. SCI., 56:458–468, 2016. © 2016 Society of Plastics Engineers     

Synthesis of compatibilizers and characterization of the compatibilized and noncompatibilized blends of PP/Rodrun LC3000

The addition of a liquid crystalline polymer (LCP) to a matrix of a flexible thermoplastic (TP) has been used in the last two decades as an in situ reinforcement of the matrix. Owing to the immiscibility of the two phases and the high degree of orientation typical of LCPs, the dispersed phase is, after processing, essentially constituted by fibrillar structures, which are responsible for the reinforcement of the matrix and the decrease of viscosity with respect to the matrix. The low degree of adhesion typical of LCP/TP blends often requires the use of compatibilizers, which will act reducing the interfacial tension between the two components. In this work, we present the synthesis of three different compatibilizers, as well as the mechanical characterization of the corresponding compatibilized blends. Some scanning electron microphotographs will be also presented to better explain the mechanical results. The mechanical properties of these blends were compared with the noncompatibilized blend, as well as with the ones presented by blends obtained with two commercial compatibilizers, leading to the conclusion that, considering our compatibilizer C, the one that leads to the higher enhancement of the Young's modulus, when compared with the noncompatibilized blend, we obtain a Young's modulus 27% higher than the one presented by the noncompatibilized blend. Comparing this result with those presented by the blends compatibilized with the two commercial compatibilizers, D and E, we conclude that this enhancement is higher than those presented by those blends (increase in Young's modulus of 16% for both compatibilizers). © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

Morphological,thermal, rheological,and mechanical properties of PP/EVOH blends compatibilized with PP‐g‐IA

We prepared some blends of polypropylene (PP) and ethylene vinyl alcohol (EVOH) with and without a compatibilizer. As a new compatibilizer, we synthesized polypropylene grafted with itaconic acid (PP‐g‐IA) using Brabender mixing system. We investigated the morphological, thermal, rheological, and mechanical properties of a compatibilized blends (PP/EVOH/PP‐g‐IA) and not compatibilized blends (PP/EVOH). Our experiments showed that carboxylic acid groups in PP‐g‐IA and hydroxyl group in EVOH formed strong in situ hydrogen bond in the compatibilized blends, resulting in better morphological and mechanical properties of the compatibilized blends than those of not compatibilized blends. POLYM. ENG. SCI., 56:1240–1247, 2016. © 2016 Society of Plastics Engineers     

Miscibility enhancement of PP/PBT blends with a side‐chain liquid crystalline ionomer

Side‐chain liquid crystalline ionomer (SLCI) containing sulfonic acid groups with a polymethylhydrosiloxane main‐chain was used in the blends of polypropylene (PP) and polybutylene terephthalate (PBT) as a compatibilizer. The crystalline behavior, morphological, and mechanical properties of the blends were investigated in detail by differential scanning calorimetry (DSC), polarizing optical microscope (POM), Fourier transforms infrared spectroscopy (FTIR), and scanning electron microscopy (SEM). Revealed by the shift of T_m in DSC thermogram and the shift of the absorbed peak in FTIR spectra, specific interaction led to stronger interfacial adhesion between these phases, which resulted in much finer dispersion of the minor PBT phase in PP matrix. The SLCI containing sulfonate acid groups acted as physical crosslinking agent along the interface, which compatibilized PP/PBT blends. The mechanical property of the blends including 4 wt % SLCI contents was better than that of other SLCI contents in the blends. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Studies on morphology,mechanical, thermal,and dynamic mechanical behavior of extrusion blended polypropylene and thermotropic liquid crystalline polymer in presence of compatibilizer

Polypropylene was melt blended in a single screw extruder with thermo tropic Vectra B‐950 liquid crystalline polymer (copolyester amide) in different proportions in presence of 2% of EAA, ethylene‐acrylic acid copolymer (based on PP) as a compatibilizer. The mechanical properties of such compatibilized blends were evaluated and compared in respect of their Young's Modulii, Ultimate tensile strength, percent elongation at break, and toughness to those of Pure PP. The Morphology was studied by using a polarizing light microscope (PLM) and Scanning electron microscope (SEM). The Thermal characterization of these blends were carried out by differential scanning calorimeter (DSC).The mechanical properties under dynamic conditions of such compatibilized blends and pure PP were studied by dynamic mechanical analyzer (DMA). Mechanical analysis (Tensile properties) of the compatibilized blends displayed improvements in Modulii and ultimate tensile strength (UTS) of PP matrix with the incorporation of 2–10% of LCP incorporation. The development of fine fibrillar morphology in the compatibilized PP/LCP blends had large influence on the mechanical properties. Differential scanning calorimeter (DSC) studies indicated no remarkable changes in the crystalline melting temperature of the blends with respect to that of pure PP. However, an increase in the softening range of the blends over that of PP was observed. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Comparing the compatibility of various functionalized polypropylenes with thermoplastic polyurethane (TPU)

Three functionalized polypropylenes (PP), a maleated PP (PP-g-MA), primary amine functionalized PP (PP-g-NH₂), and secondary amine functionalized PP (PP-g-NHR), were melt blended with a thermoplastic polyurethane (TPU) at different compositions. Compatibility of each functionalized PP with TPU was compared by investigating the binary blends using rheological (mixer torques, dynamic shear rheometry), thermal (dynamic mechanical analysis), mechanical (tensile test), and morphological (scanning electron microscopy with image analysis, particle size analysis) measurements. Compatibility of the three functionalized PP's with TPU is ranked in a decreasing order as follows: PP-g-NHR≥PP-g-NH₂?PP-g-MA, which is attributed to higher reactivity of amine (primary and secondary) with urethane linkages. Accordingly, the TPU blends with the two types of amine functionalized PP's exhibited much better synergy, as reflected by much improved mechanical properties including higher tensile strength and ultimate elongation, and finer and more stable morphologies.     

In situ reactive compatibilized noryl/LCP blends

This article reveals that the already known improved properties of the thermoplastic–liquid crystalline polymer (LCP) blends can be further improved substantially over the corresponding noncompatibilized counterparts by using a reactive in situ type compatibilizer, the styrene–glycidyl methacrylate (SG) copolymer. This SG copolymer has been demonstrated in this article to be an effective reactive compatibilizer to improve the processability, heat deflection temperature, and mechanical properties of Noryl/LCP blends. The epoxy functional groups of the SG copolymer can react with the end groups of PPO (in Noryl) and LCP. The in situ-formed SG–g–LCP copolymer tends to reside along the interface of Noryl–LCP and reduces the interfacial tension during melt processing. The resultant LCP fibers in the Noryl matrix of the compatibilized blends have a higher aspect ratio because the fibers become finer, longer, and tend to form lamellate domains with a greater interphase contact area than those from the noncompatibilized blends. The compatibilized blends also improve the interphase adhesion between Noryl and LCP. The presence of ethyl triphenylphosphonium bromide catalyst promotes the grafting reaction to improve blend compatibilization. © 1995 John Wiley & Sons, Inc.     

Compatibilization efficiency of styrene–butadiene triblock copolymers in polystyrene–polypropylene blends with varying compositions

The compatibilization efficiency of two styrene‐butadiene‐styrene triblock copolymers with short (SB1) and long (SB2) styrene blocks was studied in polystyrene (PS)–polypropylene (PP) blends of composition 20, 50, and 80 wt % PS. The supramolecular structure of the blends was determined by small‐angle X‐ray scattering, and the morphology was studied with transmission electron microscopy and scanning electron microscopy. Structural changes in both the uncompatibilized and compatibilized blends were correlated with the values of tensile impact strength of these blends. Even though the compatibilization mechanisms were different in blends with SB1 and SB2, the addition of the block copolymers to the PS–PP 4/1 and PS–PP 1/4 blends led to similar structures and improved the mechanical properties in the same way. These block copolymers had a very slight effect on the impact strength in PS–PP 1/1 blends, exhibiting a nearly cocontinuous phase morphology. The strong migration of SB2 copolymers to the interface and of SB1 copolymers away from the interface were detected during the annealing of compatibilized PS–PP 4/1 blends. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 2431–2441, 2004     

The effect of mercapto‐modified ethylene–vinyl acetate (EVA) on curing parameters,mechanical properties,and thermal properties of vulcanized styrene–butadiene rubber (SBR)/EVA blends

The effect of EVA functionalized with mercapto groups (EVALSH) on the compatibilization of SBR and EVA copolymer blends was investigated in vulcanized systems based on sulfur or dicumyl peroxide (DCP). The presence of EVALSH resulted in an improvement of the tensile properties, indicating the reactive compatibilizing effect of this compound. The best mechanical performance was achieved with the sulfur‐curing system for both compatibilized and noncompatibilized blends. The blend systems were also analyzed by scanning electron microscopy, differential scanning calorimetry, and dynamic‐mechanical analysis. The crystallinity of the EVA phase was significantly affected by the presence of the EVALSH, whereas no substantial change was detected on the damping properties or the glass transition temperature of the SBR phase. Considering the aging properties, the presence of EVALSH increases the thermal stability of the blends vulcanized with DCP. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 86: 239–249, 2002     

In situ compatibilization of PET/PS blends through reactive copolymers

Polymer blends of poly(ethylene terephthalate) (PET) and polystyrene (PS) are immiscible and incompatible, which has been well recognized. Styrene–glycidyl methacrylate (SG) copolymer has been synthesized by suspension polymerization and employed in this study as an in situ compatibilizer for the polyblends of PET and PS. This copolymer contains reactive epoxy functional groups that are able to react with PET end groups ? OH and ? COOH) under melt conditions to from SG-graft-PET copolymer. The presence of a small amount of phosphonium catalyst (200 ppm) accelerated the graft reaction and results in a better compatibilized blend. The compatibilized PET/PS blend has a smaller phase domain and higher viscosity than does the corresponding noncompatibilized blend. Mechanical properties of the compatibilized blends have also been improved significantly over the corresponding noncompatibilized blends. © 1993 John Wiley & Sons, Inc.     

Effect of styrene–isoprene–styrene,styrene–butadiene–styrene,and styrene–butadiene–rubber on the mechanical,thermal, rheological,and morphological properties of polypropylene/polystyrene blends

The mechanical, thermal, rheological, and morphological properties of polypropylene (PP)/polystyrene (PS) blends compatibilized with styrene–isoprene–styrene (SIS), styrene–butadiene–styrene (SBS), and styrene–butadiene–rubber (SBR) were studied. The incompatible PP and PS phases were effectively dispersed by the addition of SIS, SBS, and SBR as compatibilizers. The PP/PS blends were mechanically evaluated in terms of the impact strength, ductility, and tensile yield stress to determine the influence of the compatibilizers on the performance properties of these materials. SIS‐ and SBS‐compatibilized blends showed significantly improved impact strength and ductility in comparison with SBR‐compatibilized blends over the entire range of compatibilizer concentrations. Differential scanning calorimetry indicated compatibility between the components upon the addition of SIS, SBS, and SBR by the appearance of shifts in the melt peak of PP toward the melting range of PS. The melt viscosity and storage modulus of the blends depended on the composition, type, and amount of compatibilizer. Scanning electron microscopy images confirmed the compatibility between the PP and PS components in the presence of SIS, SBS, and SBR by showing finer phase domains. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 88: 266–277, 2003     

Rheologically determined phase behavior and miscibility of reactively compatibilized poly(ethylene terephthalate)/polypropylene blends

Rheology, phase behavior and morphology of poly(ethylene terephthalate)/polypropylene (PET/PP) blends compatibilized with maleic-anhydrate-grafted-PP (PP-g-MA) and n-butyl-acrylate-glycidyl-methacrylate-ethylene (EBGMA) were studied. According to infrared spectroscopy results, whereas PP-g-MA was merely capable of reacting with hydroxyl groups of PET, epoxy groups of EBGMA could react with both the hydroxyl and carboxyl end groups of PET. The enhanced compatibilizing effect of EBGMA on PET/PP systems over PP-g-MA was also revealed by scanning electron microscopy and mechanical experiments. From frequency and temperature sweep rheological experiments, the dynamic characteristics of the compatibilized blends found to be improved in comparison with those of the uncompatibilized system. Such enhancement was interpreted as a result of the higher miscibility of the compatibilized blends which was further supported by Cole–Cole plot analyses.