Structural and performance properties of UV-assisted TiO2 deposited nano-composite PVDF/SPES membranes

In this research, the surface of poly (vinylidene fluoride) (PVDF)/sulfonated polyethersulfone (SPES) blend membrane prepared via immersion precipitation was modified by depositing of TiO₂ nano-particles followed by UV irradiation to activate their photocatalytic property. The membranes were characterized by FTIR, SEM, AFM, contact angle, dead end filtration (pure water flux and BSA solution flux), antifouling analysis and antibacterial activity. The FTIR spectrum confirmed the presence of OH functional groups on the PVDF/SPES membrane structure, which was the key factor for deposition, and self-assembly of TiO₂ nanoparticles on the membrane surface. The SEM and AFM images indicated that the TiO₂ nanoparticles were deposited on the PVDF/SPES membrane. The contact angle measurements showed that the hydrophilicity of PVDF/SPES membrane was strongly improved by TiO₂ deposition and UV irradiation. The filtration results indicated that the initial flux of TiO₂ deposited PVDF/SPES membranes was lower than the initial flux of neat PVDF/SPES membrane. However, the former membranes showed lower flux decline compared to the neat PVDF/SPES membrane. The BSA rejection of modified membranes was improved. The fouling analysis demonstrated that the TiO₂ deposited PVDF/SPES membranes showed the fewer tendencies to fouling. The results of antibacterial study showed that the UV irradiated TiO₂ deposited PVDF/SPES membranes possess high antibacterial property.     

High permeability poly(vinylidene fluoride) ultrafiltration membrane doped with polydopamine modified TiO2 nanoparticles

In order to improve the water permeability of poly(vinylidene fluoride) (PVDF) ultrafiltration (UF) membranes with low molecular weight cut-off (MWCO), polydopamine (PDA) was employed in the membrane preparation process. Owing to its merits of material-independent adhesion, PDA was coated on inorganic particles or added in coagulation bath to tailor the final membrane structure and property. The introduction of PDA broke through the permeability/selectivity trade-off of the PVDF membrane. By adding the PDA coated titanium dioxide (PDA/TiO₂) nanoparticles, water flux increased by 287% while MWCO kept similar with the pristine PVDF membrane. Thermodynamics and Kinetics of the PVDF/additives/non-solvent were analyzed and shown that nanoparticles reduced the thermodynamic stability and increased the phase separation speed, and the speed can be adjusted using different nanoparticles. Additionally, X-ray diffraction (XRD) test indicated that PVDF crystalline form changed from α phase to β phase after adding different nanoparticles. Permeability/selectivity trade-off was broken through by DA addition in coagulation bath. Compared with the original PVDF membrane, when the DA concentration of the coagulation bath was 2.0 g·L⁻¹, water flux increased by 312%, and MWCO of the PVDF membrane ranged in 10,000 to 20,000 Da as well as contact angle decreased from 81.4° to 45°.     

Effect of additives concentration on the surface properties and performance of PVDF ultrafiltration membranes for refinery produced wastewater treatment

The aim of this study was to investigate the effect of pore-forming hydrophilic additives on the porous asymmetric polyvinylideneflouride (PVDF) ultrafiltration (UF) membrane morphology and transport properties for refinery produced wastewater treatment. PVDF ultrafiltration membranes were prepared via a phase inversion method by dispersing lithium chloride monohydrate (LiCl·H₂O) and titanium dioxide (TiO₂) nanoparticles in the spinning dope. The morphological and performance tests were conducted on PVDF ultrafiltration membranes prepared from a different additive content. The top surface and cross-sectional area of the membranes were observed using a field emission scanning electron microscope (FESEM) and energy dispersive X-ray (EDX) analysis. The surface wettability of porous membranes was determined by the measurement of a contact angle. The mean pore size and surface porosity were calculated based on the permeate flux. The results indicated that the PVDF/LiCl/TiO₂ membranes with lower TiO₂ nanoparticles loading possessed smaller mean pore size, more apertures inside the membrane with enhanced membrane hydrophilicity. LiCl·H₂O has been employed particularly to reduce the thermodynamic miscibility of dope which resulted in increasing the rate of liquid–liquid demixing process. The maximum flux and rejection of refinery wastewater using PVDF ultrafiltration membrane achieved were 82.50 L/m² h and 98.83% respectively at 1.95 wt.% TiO₂ concentration.     

Studies on the surface properties of mixed‐matrix membrane and its antifouling properties for humic acid removal

A major factor limiting the use of ultrafiltration (UF) membrane in water treatment process is the membrane fouling by natural organic matter such as humic acid (HA). In this work, neat PVDF and PVDF/TiO₂ mixed‐matrix membranes were prepared and compared in terms of their antifouling properties. Two commercial types of TiO₂ namely PC‐20 and P25 were embedded to prepare the mixed matrix membranes via in situ colloidal precipitation method. The contact angles for the mixed‐matrix membranes were slightly reduced while the zeta potential was increased (more negatively charged) compared with the neat membrane. Filtration of HA with the presence of Ca²⁺ demonstrated that mixed‐matrix membrane could significantly mitigate the fouling tendency compared with the neat membrane with flux ratio (J/J₀) of 0.65, 0.70, and 0.82 for neat PVDF membrane, PVDF/TiO₂ mixed‐matrix membrane embedded with P25 and PC‐20, respectively. PC‐20 with higher anatase polymorphs exhibited better antifouling properties due to its hydrophilicity nature. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Antifouling behaviour of PVDF/TiO2 composite membrane: a quantitative and qualitative assessment

The composite membranes of PVDF/TiO₂ were prepared by a phase-inversion technique. Different amounts of TiO₂ with respect to the weight of the polymer were incorporated in the casting solution to study qualitatively and quantitatively the antifouling property of the membrane. The membrane morphology was studied using a high-resolution scanning electron microscopy and atomic force microscopy, whereas the crystalline nature was studied using X-ray diffraction method. The interfacial interactions between foulants and TiO₂ immobilized membranes were also evaluated using the extended Derjaguin–Landau–Verwey–Overbeek (XDLVO) approach. The XDLVO theory revealed an increase in repulsive interactive energy barrier with an increase in TiO₂ loading, thus causing to improve the antifouling property of the membrane. Intercalation of TiO₂ nanoparticles efficiently improved the porosity and wettability of the polymeric membranes, which could be confirmed by the contact angle analyzer analysis. The modified PVDF membranes exhibited excellent antimicrobial properties against Gram-negative Escherichia coli as confirmed from the halo zone and activity test. The permeation experimental results also showed high protein rejection of bovine serum albumin and humic acid (foulant) for membranes with optimum TiO₂ loading of 0.01 g/g of PVDF polymer. However, at a concentration of 0.02 g TiO₂/g of PVDF a negative effect on the membrane property was observed due to the former non-uniform distribution.

     

Mixed Matrix PVDF/Graphene and Composite‐Skin PVDF/Graphene Oxide Membranes Applied in Membrane Distillation

This work elucidates the influence of graphene (G) and graphene oxide (GO) content on the desalination performance and scaling characteristics of G/polyvinylidene fluoride (G/PVDF) mixed matrix and GO/PVDF composite‐skin membranes, applied in a direct contact membrane distillation process (DCMD). Inclusion of high quality, nonoxidized, monolayered graphene sheets as polymer membrane filler, and application of a novel GO/water‐bath coagulation method for the preparation of the GO/PVDF composite films, took place. Water permeability and desalination tests via DCMD, revealed that the optimal G content was 0.87 wt%. At such concentration the water vapor flux of the G/PVDF membrane was 1.7 times that of the nonmodified reference, while the salt rejection efficiency was significantly improved (99.8%) as compared to the neat PVDF. Similarly the GO/PVDF surface‐modified membrane, prepared using a GO dispersion with low concentration (0.5 g/L), exhibited twofold higher water vapor permeate flux as compared to the neat PVDF, but however, its salt rejection efficiency was moderate (80%), probably due to pore wetting during DCMD. The relatively low scaling tendency observed for both G and GO modified membranes is primarily attributed to their smoother surface texture as compared to neat PVDF, while scaling is caused by the deposition of calcite crystals, identified by XRPD analysis. POLYM. ENG. SCI., 59:E262–E278, 2019. © 2018 Society of Plastics Engineers     

PVDF/TiO2/graphene oxide composite nanofiber membranes serving as separators in lithium-ion batteries

Improving the electrochemical properties of membranes in lithium-ion batteries (LIBs) is very important. Many attempts have been made to optimize ionic conductivity of membranes. The aim of this study was fabricating composite nanofiber membranes of poly(vinylidene fluoride) (PVDF), containing titanium dioxide (TiO₂) and graphene oxide (GO) nanoparticles to use in LIBs as separators. The morphology, crystallinity, porosity, pore size, electrolyte uptake, ionic conductivity, and electrochemical stability of the membranes were investigated using scanning electron microscopy, wide-angle X-ray diffraction, Fourier transform infrared spectroscopy, electrochemical impedance spectroscopy, and linear sweep voltammetry. The electrolyte uptake and ionic conductivity of the PVDF/TiO₂/GO composite nanofiber membranes containing 2 wt % GO were 494% and 4.87 mS cm⁻¹, respectively, which were higher than those of the other fabricated membranes as well as the commercial Celgard membrane. This could be attributed to the increased porosity, larger surface area, and higher amorphous regions of the PVDF/TiO₂/GO composite nanofiber membranes as a result of the synergistic effects of the nanoparticles. In this work, suitable optimized membranes with greater electrochemical stability compared with the other membranes were presented. Also, it was demonstrated that the incorporation of the TiO₂ and GO nanoparticles into the PVDF nanofiber membranes led to a porous structure where the electrolyte uptake enhanced. These properties made these membranes promising candidates for being used as separators in LIBs. © 2019 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2020 , 137, 48775.     

PVDF–TiO2 composite hollow fiber ultrafiltration membranes prepared by TiO2 sol–gel method and blending method

Organic–inorganic polyvinylidene fluoride (PVDF)–titanium dioxide (TiO₂) composite hollow fiber ultrafiltration (UF) membranes were prepared by TiO₂ sol–gel method and blending method, respectively. The membranes were characterized in terms of microstructure, hydrophilicity, permeation performance, thermal stability, and mechanical strength. The experimental results indicated that PVDF–TiO₂ composite UF membranes exhibited significant differences in surface properties and intrinsic properties because of the addition of inorganic particles. The TiO₂ particles improved the membrane strength and thermal stability of PVDF–TiO₂ composite UF membranes. In particular, hydrophilicity and permeability increased dramatically with the increase of TiO₂, whereas the retention property of UF membranes was nearly unchanged. However, high TiO₂ concentration induced the aggregation of particles, resulting in the decline of hydrophilicity and permeability. Compared with PVDF–TiO₂ composite hollow fiber UF membranes prepared by TiO₂ blending method, PVDF–TiO₂ composite hollow fiber UF membranes prepared by TiO₂ sol–gel method formed a dispersed inorganic network, and the stronger interaction between inorganic network and polymeric chains led to TiO₂ particles being uniformly dispersed in UF membranes. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Preparation of photo-catalytic copolymer grafted asymmetric membranes (N-TiO<Subscript>2</Subscript>-PMAA-g-PVDF/PAN) and their application on the degradation of bentazon in water

Nitrogen-doped titanium dioxide (N–TiO₂) was prepared and supported on a novel copolymer grafted membrane matrix to avoid the problems associated with the removal of spent photocatalyst from treated water. Membranes of poly (methacrylic acid) grafted onto poly (vinylidene difluoride) and blended with poly (acrylonitrile) (PMAA-g-PVDF/PAN) were prepared through a dry–wet phase inversion technique. Methacrylic acid side chains were grafted onto an activated PVDF backbone by the method of reversible addition fragmentation chain transfer polymerization and then the novel photocatalytic asymmetric membranes of N–TiO₂–PMAA-g-PVDF/PAN were prepared. The casting solutions were blended with 1–5 % N–TiO₂ before immersion into the coagulation bath. PVDF and PAN offer several advantages which include: mechanical strength and toughness, chemical resistance, unaffected by long-term exposure to UV radiation, low weight, and thermal stability. N–TiO₂ was prepared through sol-gel synthesis. The photocatalytic membranes were evaluated by degradation process of herbicide bentazon in water. Photodegradation studies revealed that the optimum photocatalyst loading was 3 % N–TiO₂ and the optimum pH was 7 for the degradation of bentazon in water. UV–Vis, TOC and LC–MS analyses confirmed the successful photodegradation of bentazon. A bentazon removal efficiency of 90.1 % was achieved at pH 7. N–TiO₂–PMAA-g-PVDF/PAN membranes were successfully prepared and characterized. These photocatalytic membranes showed great potential as a technology for the effective removal of pesticides from water. According to literature, N–TiO₂–PMAA-g-PVDF/PAN asymmetric photocatalytic membranes have not been prepared before for the purpose of treating agricultural wastewater.     

Poly(vinylidene fluoride) ultrafiltration membranes containing hybrid silica nanoparticles: Preparation,characterization and performance

Poly(vinylidene fluoride) (PVDF) ultrafiltration membranes were prepared by immersion precipitation method using poly(hydroxyethyl methacrylate)-block-poly(methyl methacrylate) grafted silica (PHEMA-b-PMMA@SiO₂) nanoparticles as additives. The hybrid nanoparticles were synthesized by the surface initiated atom transfer radical polymerization (SI-ATRP), and they were characterized in detail by FT-IR, TEM, DLS and GPC. Results confirm that core–shell structure is formed after grafting PHEMA-b-PMMA brushes on the silica nanoparticles. Their average hydrodynamic diameter also increases with the prolongation of grafting time. After blending PVDF with the hybrid silica nanoparticles, the composite PVDF membranes exhibit high porosity and improved water permeation. Especially, when the molecular weight is 1.73 × 10⁵ g/mol for PHEMA-b-PMMA on the hybrid nanoparticles, the water flux of the PVDF composite membrane is 2.5 times than that of the control PVDF membrane, while the rejection to bovine serum albumin (BSA) remains at a high level (>90%). In addition, all the composite PVDF membranes show lower BSA adsorption and larger water flux recovery ratio than the control PVDF membrane. The improvement of membrane performance is attributed to the good hydrophilicity of PHEMA-b-PMMA@SiO₂ nanoparticles. Our results suggest that PHEMA-b-PMMA@SiO₂ nanoparticles with moderate molecular weight of PHEMA-b-PMMA are suitable for the property optimization of PVDF-based composite membranes.     

Photocatalytic and antimicrobial efficacy of PVDF/TiO2 membranes fabricated by solution blow spinning

With its ability to purify water and treat wastewater, photocatalytic membranes have become a promising solution. The membrane's unique properties allow for the separation of solid compounds and the degradation of organic materials through photocatalytic and antibacterial means. Poly(vinylidene fluoride)/titanium oxide (PVDF/TiO₂) composite remain the materials of choice for making these membranes due to their economy, effectiveness, safety, and durability. In this work a photocatalytic membrane reactor (PMR) system was developed using PVDF/TiO₂ membranes fabricated by the solution blow spinning (SBS) process. Obtaining photocatalytic membranes using this method is an efficient and ecological route that overcomes the disadvantage of separating the photocatalyst after the treatment is complete. The results of PMR system showed that the PVDF/TiO₂ membrane could effectively remove total coliforms and E. coli from polluted water. After 10 min of contaminated water circulation through the PMR system, the presence of pathogens was not detected, indicating the efficiency of the obtained membranes.     

Nano SiO2 and TiO2 embedded polyacrylonitrile/polyvinylidene fluoride ultrafiltration membranes: Improvement in flux and antifouling properties

Polyvinylidene fluoride (PVDF) and polyacrylonitrile (PAN) ultrafiltration (UF) membranes are widely used in drinking water and wastewater applications. These membranes are prone to fouling and membrane efficiency decreases with time under constant operation. Significant improvements/modifications are necessary to apply these polymers as sustainable membrane materials. In this study, PVDF and PAN UF membranes were modified through incorporation of nanoparticles (NPs) namely SiO₂ and TiO₂. PVDF and PAN UF membranes were prepared by phase inversion method from polymer solutions having dispersed SiO₂ and TiO₂ NPs in it. Membrane surface hydrophilicity, charge, roughness, and morphology were studied. Equilibrium water content and molecular weight cut-off of the membranes were also measured. Addition of NPs increased membrane surface hydrophilicity, equilibrium water content, and surface potential. NPs modified membranes exhibited better membrane flux (35–79% higher) and antifouling properties (flux recovery ratio values 28–41% higher) than the virgin membranes.     

Synthesis and characterization of PVA/PES thin film composite nanofiltration membrane modified with TiO2 nanoparticles for better performance and surface properties

Novel polyethersulfone (PES)/poly (vinyl alcohol) (PVA)/titanium dioxide (TiO₂) composite nanofiltration membranes were prepared by dip-coating of PES membrane in PVA and TiO₂ nanoparticles aqueous solution. Glutaraldehyde (GA) was used as a cross-linker for the composite polymer membrane in order to enhance the chemical, thermal as well as mechanical stabilities. TiO₂ nanoparticles with different concentrations (0, 0.05, 0.1, 0.5 wt.%) were coated on the surface of PVA/PES composite membrane. The morphological study was investigated by atomic force microscopy (AFM), scanning surface microscopy (SEM) and along with X-ray diffraction (XRD). In addition, the membranes performances, in terms of permeate flux, ion rejection and swelling factor were also investigated. It was found that the increase in TiO₂ solution concentration can highly affect the surface morphology and filtration performance of coated membranes. The contact angle measurement and XRD studies indicated that the TiO₂ nanoparticles successfully were coated on the surface of PVA/PES composite membranes. However, rougher surface was obtained for membranes by TiO₂ coating. The filtration performance data showed that the 0.1 wt.% TiO₂-modified membrane presents higher performance in terms of flux and NaCl salt rejection. Finally, TiO₂ modified membranes demonstrated the lower degree of swelling.     

Effect of calcination temperature of TiO2 on the crystallinity and the permittivity of PVDF‐TrFE/TiO2 composites

Composite membranes of poly(vinylidene‐trifluoroethylene)/titanium dioxide (PVDF‐TrFE/TiO₂) were prepared by the solution cast method. The crystallization behavior and dielectric properties of the composites with TiO₂ calcined at different temperatures were studied. Transmission electron microscopy and X‐ray diffraction (XRD) results showed that the TiO₂ nanoparticles calcined at different temperatures were well dispersed in the polymer matrix and did not affect the structure of the PVDF‐TrFE matrix. XRD and differential scanning calorimeter measurements showed that the crystallinity of PVDF‐TrFE/TiO₂ composites increased as the addition of TiO₂ with different calcination temperatures. The dielectric property testing showed that the permittivity of PVDF‐TrFE/TiO₂ membrane increased rapidly with the increase of TiO₂ content and the calcination temperature of TiO₂ at constant TiO₂ content, but the dielectric loss did not change much. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Interfacially polymerized thin film nanofiltration membranes on TiO2 coated polysulfone substrate

In this study, a new approach was developed to prepare the novel thin film composite nanofiltration membranes. In this new approach, nanoparticles were coated completely under the polymeric thin film layer. Thin film composite (TFC) membranes were fabricated by interfacial polymerization on polysulfone (PSf) sublayer using m-phenylenediamine (MPD) and trimesoyl chloride (TMC) respectively as amine monomer and acid chloride monomer. Scanning electron microscopy and atomic force microscopy were used to study surface morphology and roughness properties of NF membranes. Energy dispersive X-ray microanalysis (EDX) was used to analyze the elemental change before and after filtration experiment. Chemical structure and thickness of polyamide formed on TFC membranes were observed by Fourier transmission infrared attenuated total reflectance (FTIR-ATR) spectroscopy. Permeability, salt rejection and pepsin macromolecule rejection of prepared membranes were tested using dead end filtration cell. Antifouling behavior of the membranes was studied by filtering pure water before and after pepsin solution filtration. A smoother and thicker surface without any defect appeared as the concentration of nanoparticle was increased. NaCl rejection was increased from 70% for neat nanofiltration membrane to 84% for 0.5 wt% TiO₂ modified nanofiltration membrane. Antifouling and permeability behavior of the prepared membranes were improved in the new approach. Antibacterial property of prepared membranes was improved as a result of photocatalytic characteristic of TiO₂ nanoparticles.     

Influence of the coagulation‐bath temperature on the phase‐separation process of poly(vinylidene fluoride)‐graft‐poly(N‐isopropylacrylamide) solutions and membrane structures

A poly(vinylidene fluoride)‐graft‐poly(N‐isopropylacrylamide) (PVDF‐g‐PNIPAAm) copolymer was synthesized, and flat‐sheet membranes were prepared via the phase‐inversion method with N,N‐dimethylformamide (DMF) as the solvent and water as the coagulation bath. The effects of the coagulation‐bath temperature on poly(vinylidene fluoride) (PVDF)/DMF/water and PVDF‐g‐PNIPAAm/DMF/water ternary systems were studied with phase diagrams. The results showed that the phase‐separation process could be due to the hydrophilicity/hydrophobicity of poly(N‐isopropylacrylamide) at low temperatures, and the phase‐separation process was attributed to crystallization at high temperatures. The structures and properties of the membranes prepared at different coagulation‐bath temperatures were researched with scanning electron microscopy, porosity measurements, and flux measurements of pure water. The PVDF‐g‐PNIPAAm membranes, prepared at different temperatures, formed fingerlike pores and showed higher water flux and porosity than PVDF membranes. In particular, a membrane prepared at 30°C had the largest fingerlike pores and greatest porosity. The water flux of a membrane prepared in a 25°C coagulation bath showed a sharp increase with the temperature increasing to about 30°C. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

PEG/GO/TiO2纳米复合材料改性PVDF膜的制备及其抗污性能

为改善聚偏氟乙烯(PVDF)膜的抗污性能,以聚乙二醇2000接枝的GO/TiO₂(PEG/GO/TiO₂)纳米复合材料为添加剂,通过非溶剂诱导沉淀相分离法制备了一系列PEG/GO/TiO₂/PVDF复合超滤膜。采用FTIR、SEM和接触角测试仪对其结构和形貌进行了表征,采用超滤法评价其纯水通量和抗污性能。结果表明,当PEG/GO/TiO₂纳米复合材料质量分数为0.60%时,制备的PEG/GO/TiO₂/PVDF复合超滤膜(记为0.60%PEG/GO/TiO₂/PVDF)表现出最佳的亲水性和抗污性能,其接触角比PVDF膜下降8.2°,总孔隙率增加13.40%,PEG/GO/TiO₂纳米复合材料在PVDF膜中分散较均匀。在0.08 MPa的工作压力下,0.60%PEG/GO/TiO₂/PVDF的纯水通量高达282.44 L/(m²·h),对腐植酸溶液的过滤通量为131.96 L/(m^2...     

High permeability poly(vinylidene fluoride) ultrafiltration membrane doped with polydopamine modified TiO2 nanoparticles

In order to improve the water permeability of poly(vinylidene fluoride) (PVDF) ultrafiltration (UF) membranes with low molecular weight cut-off (MWCO), polydopamine (PDA) was employed in the membrane preparation process. Owing to its merits of material-independent adhesion, PDA was coated on inorganic particles or added in coagulation bath to tailor the final membrane structure and property. The introduction of PDA broke through the permeability/selectivity trade-off of the PVDF membrane. By adding the PDA coated titanium dioxide (PDA/TiO₂) nanoparticles, water flux increased by 287% while MWCO kept similar with the pristine PVDF membrane. Thermodynamics and Kinetics of the PVDF/additives/non-solvent were analyzed and shown that nanoparticles reduced the thermodynamic stability and increased the phase separation speed, and the speed can be adjusted using different nanoparticles. Additionally, X-ray diffraction (XRD) test indicated that PVDF crystalline form changed from α phase to β phase after adding different nanoparticles. Permeability/selectivity trade-off was broken through by DA addition in coagulation bath. Compared with the original PVDF membrane, when the DA concentration of the coagulation bath was 2.0 g·L^-1, water flux increased by 312%, and MWCO of the PVDF membrane ranged in 10,000 to 20,000 Da as well as contact angle decreased from 81.4° to 45°.     

凝固浴组成和温度对PVDF疏水微孔膜结构与性能的影响

利用非溶剂相转化法(NIPS),以聚偏氟乙烯(PVDF)/磷酸三乙酯(TEP)-N,N-二甲基乙酰胺(DMAc)为铸膜液体系,乙醇水溶液为凝固浴制备高性能的PVDF疏水微孔膜。考察了凝固浴中乙醇(EtOH)含量及凝固浴温度对PVDF成膜分相速率、膜结构和膜疏水性的影响。实验结果表明,在20℃的凝固浴温度下,凝固浴中乙醇含量的升高减慢了铸膜液体系的分相速率,提高了PVDF膜的孔隙率;在凝固浴中添加60%(wt)的乙醇,可形成表面荷叶状结构和截面对称的海绵状结构,膜表面的接触角为130.3°,呈很强的疏水性,并具有较优的膜强度。     

Hydrophilicity and crystallization behavior of PVDF/PMMA/TiO<Subscript>2</Subscript>(SiO<Subscript>2</Subscript>) composites prepared by in situ polymerization

Composites with enhanced hydrophilicity were prepared by adding TiO₂ or SiO₂ nanoparticles during the in situ polymerization of methyl methacrylate (MMA) in poly(vinylidene fluoride) (PVDF). The hydrophilicities of the PVDF/PMMA/TiO₂(SiO₂) composites generated in this manner were characterized by contact angle measurements and atomic force microscopy (AFM). The hydrophilicity was dependent on nanoparticle content; it gradually increased with increasing TiO₂ (or SiO₂) content when the TiO₂ (or SiO₂) content was no more than 4 wt% of PVDF. A homogeneous dispersion of the TiO₂ (or SiO₂) nanoparticles in the composite matrix was observed in scanning electron microscope (SEM) images. Based on Fourier transform infrared (FTIR) spectra and wide angle X-ray diffraction (WAXD) analyses, the crystalline phase composition of PVDF was not influenced by the addition of TiO₂ (or SiO₂); PVDF crystallized predominantly in the α phase after in situ polymerization. Nevertheless, the nanoparticles can promote the formation of the β phase of PVDF in composites; the β-phase content increased with increasing TiO₂ content, while it was almost independent of SiO₂ content.