Synthesis and characterization of poly(ε‐caprolactone)‐b‐poly(ethylene glycol)‐b‐poly(ε‐caprolactone) triblock copolymers with dibutylmagnesium as catalyst

Two series of poly(ε‐caprolactone)‐b‐poly(ethylene glycol)‐b‐poly(ε‐caprolactone) triblock copolymers were prepared by the ring opening polymerization of ε‐caprolactone in the presence of poly(ethylene glycol) and dibutylmagnesium in 1,4‐dioxane solution at 70°C. The triblock structure and molecular weight of the copolymers were analyzed and confirmed by ¹H NMR, ¹³C NMR, FTIR, and gel permeation chromatography. The crystallization and thermal properties of the copolymers were investigated by wide‐angle X‐ray diffraction (WAXD) and differential scanning calorimetry (DSC). The results illustrated that the crystallization and melting behaviors of the copolymers were depended on the copolymer composition and the relative length of each block in copolymers. Crystallization exothermal peaks (T_c) and melting endothermic peaks (T_m) of PEG block were significantly influenced by the relative length of PCL blocks, due to the hindrance of the lateral PCL blocks. With increasing of the length of PCL blocks, the diffraction and the melting peak of PEG block disappeared gradually in the WAXD patterns and DSC curves, respectively. In contrast, the crystallization of PCL blocks was not suppressed by the middle PEG block. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Crystallization and melting behavior of poly(ε‐caprolactone‐co‐δ‐valerolactone) and poly(ε‐caprolactone‐co‐L‐lactide) copolymers with novel chain microstructures

Nuclear magnetic resonance spectroscopy (NMR) characterization of the statistical copolymers of this study showed that the poly(ε‐caprolactone‐co‐L‐lactide)s, with ε‐caprolactone (ε‐CL) molar contents ranging from 70 to 94% and ε‐CL average sequence length (l_CL) between 2.20–9.52, and the poly(ε‐caprolactone‐co‐δ‐valerolactone)s, with 60 to 85% of ε‐CL and l_CL between 2.65–6.08, present semi‐alternating (R→2) and random (R～1) distribution of sequences, respectively. These syntheses were carried out with the aim of reducing the crystallinity of poly(ε‐caprolactone) (PCL), needed to provide mechanical strength to the material but also responsible for its slow degradation rate. However, this was not achieved in the case of the ε‐caprolactone‐co‐δ‐valerolactone (ε‐CL‐co‐δ‐VAL). Non‐isothermal cooling treatments at different rates and isothermal crystallizations (at 5, 10, 21 and 37°C) were conducted by differential scanning calorimetry (DSC), and demonstrated that ε‐CL copolymers containing δ‐valerolactone (δ‐VAL) exhibited a larger crystallization capability than those of L‐lactide (L‐LA) and also arranged into crystalline structures over shorter times. The crystallization enthalpies of the ε‐CL‐co‐δ‐VAL copolymers during the cooling treatments and their heat of fusion (ΔH_m) at the different isothermal temperatures were very large (i.e. ΔH_c > 53 Jg^?1) and in some cases, unrelated to the copolymer composition. In some compositions, such as the 60 : 40, Wide Angle X‐ray Scattering (WAXS) proved that that these two lactones undergo isomorphism and co‐crystallize in a single cell. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42534.     

Influence of semi‐crystalline poly(ε‐caprolactone) and non‐crystalline polylactide blocks on the thermal properties of polydimethylsiloxane‐based block copolymers

Poly(A)‐block‐poly(B), poly(A)‐block‐poly(B)‐block‐poly(A) and B(A)₂ block copolymers were prepared through coordinated anionic ring‐opening polymerization of ε‐caprolactone (CL) and lactic acid (LA) using hydroxy‐terminated polydimethylsiloxane (PDMS) as initiator. A wide range of well‐defined combinations of PDMS‐block‐PCL and PDMS‐block‐PLA diblock copolymers, PCL‐block‐PDMS‐block‐PCL and PLA‐block‐PDMS‐block‐PLA triblock copolymers and star‐PDMS(PCL)₂ copolymers were thus obtained. The number‐average molar masses and the structure of the synthesized block copolymers were identified using various analytical techniques. The thermal properties of these copolymers were established using differential scanning calorimetry. Considering PDMS‐block‐PCL copolymers, the results demonstrate the complex effect of polymer architecture and PCL block length on the ability of the PDMS block to crystallize or not. In the case of diblock copolymers, crystallization of PCL blocks originated from stacking of adjacent chains inducing the extension of the PDMS block that can easily crystallize. In the case of star copolymers, the same tendency as in triblock copolymers is observed, showing a limited crystallization of PDMS when the length of the PCL block increases. In the case of PDMS‐block‐PLA copolymers, melting and crystallization transitions of the PLA block are never observed. Considering the diblock copolymers, PDMS sequences have the ability to crystallize. © 2019 Society of Chemical Industry     

Micro structural and non‐isothermal crystallization and degradation kinetics studies on manganese thioglycolate end capped poly(ε‐caprolactone)

The Manganese thioglycolate (Mn‐TG) end capped poly(ε‐caprolactone) (PCL) was prepared by ring opening polymerization at 160°C under inert atmosphere in the presence of Mn‐TG as an initiator and stannous octoate as a catalyst by bulk polymerization technique. The prepared PCL was investigated using various analytical tools to assess its physico‐chemical properties. The chemical structure of PCL was confirmed by Fourier transform infrared and nuclear magnetic resonance spectroscopic techniques. The particle size and morphology of the sample was examined by atomic force microscopy and TEM. The melting and crystallization behavior of PCL was analyzed using differential scanning calorimetry. The thermal property of PCL was assessed with the help of thermogravimetric analysis (TGA). The non‐isothermal crystallization kinetics was carried out to understand the nucleation type and crystal growth for the prepared PCL. The energy of activation (E_a) for crystallization process of PCL was determined. The thermal degradation of PCL and its E_a was determined under non‐isothermal condition using important kinetic models. POLYM. ENG. SCI., 59:633–642, 2019. © 2018 Society of Plastics Engineers     

Enhanced crystallization rate and mechanical properties of poly(l‐lactic acid) by stereocomplexation with four‐armed poly(ϵ‐caprolactone)‐block‐poly(d‐lactic acid) diblock copolymer

Poly(l ‐lactic acid) (PLLA) was blended with a series of four‐armed poly(? ‐caprolactone)‐block ‐poly(d ‐lactic acid) (4a‐PCL‐b ‐PDLA) copolymers in order to improve its crystallization rate and mechanical properties. It is found that a higher content of 4a‐PCL‐b ‐PDLA copolymer or longer PDLA block in the copolymer lead to faster crystallization of the blend, which is attributed to the formation of stereocomplex crystallites between PLLA matrix and PDLA blocks of the 4a‐PCL‐b ‐PDLA copolymers. Meanwhile, the PDLA block can improve the miscibility between flexible PCL phase and PLLA phase, which is beneficial for improving mechanical properties. The tensile results indicate that the 10% 4a‐PCL_5k‐b ‐PDLA_5k/PLLA blend has the largest elongation at break of about 72% because of the synergistic effects of stereocomplexation between enantiomeric PLAs, multi‐arm structure and plasticization of PCL blocks. It is concluded that well‐controlled composition and content of 4a‐PCL‐b ‐PDLA copolymer in PLLA blends can significantly improve the crystallization rate and mechanical properties of the PLLA matrix. © 2017 Society of Chemical Industry     

Confined crystallization morphology of poly(ϵ‐caprolactone) block within poly(ϵ‐caprolactone)–poly(l‐lactide) copolymers

The confined crystallization of poly(?‐caprolactone) (PCL) block in poly(?‐caprolactone)–poly(l ‐lactide) (PCL‐PLLA) copolymers was investigated using differential scanning calorimetry, polarized optical microscopy, scanning electronic microscopy and atomic force microscopy. To study the effect of crystallization and molecular chain motion state of PLLA blocks in PCL‐PLLA copolymers on PCL crystallization morphology, high‐temperature annealing (180 °C) and low‐temperature annealing (80 °C) were applied to treat the samples. It was found that the crystallization morphology of PCL block in PCL‐PLLA copolymers is not only related to the ratio of block components, but also related to the thermal history. After annealing PCL‐PLLA copolymers at 180 °C, the molten PCL blocks are rejected from the front of PLLA crystal growth into the amorphous regions, which will lead to PCL and PLLA blocks exhibiting obvious fractionated crystallization and forming various morphologies depending on the length of PLLA segment. On the contrary, PCL blocks more easily form banded spherulites after PCL‐PLLA copolymers are annealed at 80 °C because the preexisting PLLA crystal template and the dangling amorphous PLLA chains on PCL segments more easily cause unequal stresses at opposite fold surfaces of PCL lamellae during the growth process. Also, it was found that the growth rate of banded spherulites is less than that of classical spherulites and the growth rate of banded spherulites decreases with decreasing band spacing. © 2019 Society of Chemical Industry     

Synthesis of poly(vinyl alcohol)‐graft‐poly(ε‐caprolactone) and poly(vinyl alcohol)‐graft‐poly(lactide) in melt with magnesium hydride as catalyst

Grafting of poly(ε‐caprolactone) (PCL) and poly(lactide) (PLA) chains on poly(vinyl alcohol) backbone (PVA degree of hydrolysis 99%) was investigated using MgH₂ environmental catalyst and melt‐grown ring‐opening polymerization (ROP) of ε‐caprolactone (CL) and L ‐lactide (LA), that avoiding undesirable toxic catalyst and solvent. The ability of MgH₂ as catalyst as well as yield of reaction were discussed according to various PVA/CL/MgH₂ and PVA/LA/MgH₂ ratio. PVA‐g‐PCL and PVA‐g‐PLA were characterized by ¹H‐ and ¹³C‐NMR, DSC, SEC, IR. For graft copolymers easily soluble in tetrahydrofuran (THF) or chloroform, wettability and surface energy of cast film varied in relation with the length and number of hydrophobic chains. Aqueous solution of micelle‐like particles was realized by dissolution in THF then addition of water. Critical micelle concentration (CMC) decreased with hydrophobic chains. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Improvement of microstructures and properties of poly(lactic acid)/poly(ε‐caprolactone) blends compatibilized with polyoxymethylene

Incompatibility of poly(lactic acid)/poly(?‐caprolactone) (PLA/PCL) (80:20) and (70:30) blends were modified by incorporation of a small amount of polyoxymethylene (POM) (≤3 phr). Impact of POM on microstructures and tensile property of the blends were investigated. It is found that the introduction of POM into the PLA/PCL blends significantly improves their tensile property. With increasing POM loading from zero to 3 phr, elongation at break increases from 93.2% for the PLA/PCL (70:30) sample to 334.8% for the PLA/PCL/POM (70:30:3) sample. A size reduction in PCL domains and reinforcement in interfacial adhesion with increasing POM loading are confirmed by SEM observations. The compatibilization effect of POM on PLA/PCL blends can be attributed to hydrogen bonding between methylene groups of POM and carbonyl groups of PLA and PCL. In addition, nonisothermal and isothermal crystallization behaviors of PLA/PCL/POM (70:30:x) samples were investigated by using differential scanning calorimetry and wide angle X‐ray diffraction measurements. The results indicate that the crystallization dynamic of PLA matrix increases with POM loadings. It can be attributed to the fact that POM crystals have a nucleating effect on PLA. While crystallization temperature is 100 °C, crystallization half‐time can reduce from 9.4 to 2.0 min with increasing POM loading from zero to 3 phr. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 46536.     

Synthesis and physicochemical characterization of amphiphilic block copolymer self‐aggregates formed by poly(ethylene glycol)‐block‐poly(ϵ‐caprolactone)

Diblock copolymers with different poly(ε‐caprolactone) (PCL) block lengths were synthesized by ring‐opening polymerization of ε‐caprolactone in the presence of monomethoxy poly(ethylene glycol) (mPEG‐OH, MW 2000) as initiator. The self‐aggregation behaviors and microscopic characteristics of the diblock copolymer self‐aggregates, prepared by the diafiltration method, were investigated by using ¹H NMR, dynamic light scattering (DLS), and fluorescence spectroscopy. The PEG–PCL block copolymers formed the self‐aggregate in an aqueous environment by intra‐ and/or intermolecular association between hydrophobic PCL chains. The critical aggregation concentrations of the block copolymer self‐aggregate became lower with increasing hydrophobic PCL block length. On the other hand, reverse trends of mean hydrodynamic diameters were measured by DLS owing to the increasing bulkiness of the hydrophobic chains and hydrophobic interaction between the PCL microdomains. The partition equilibrium constants (K_v) of pyrene, measured by fluorescence spectroscopy, revealed that the inner core hydrophobicity of the nanoparticles increased with increasing PCL chain length. The aggregation number of PCL chain per one hydrophobic microdomain, investigated by the fluorescence quenching method using cetylpyridinium chloride as a quencher, revealed that 4–20 block copolymer chains were needed to form a hydrophobic microdomain, depending on PCL block length. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 99: 3520–3527, 2006     

Synthesis and characterization of poly(ϵ‐caprolactone)‐b‐poly(ethylene glycol) block copolymers prepared by a salicylaldimine‐aluminum complex

A series of poly(?‐caprolactone)‐b‐poly(ethylene glycol) (PCL‐b‐PEG) block copolymers with different molecular weights were synthesized with a salicylaldimine‐aluminum complex in the presence of monomethoxy poly(ethylene glycol). The block copolymers were characterized by ¹H NMR, GPC, WAXD, and DSC. The ¹H NMR and GPC results verify the block structure and narrow molecular weight distribution of the block copolymers. WAXD and DSC results show that crystallization behavior of the block copolymers varies with the composition. When the PCL block is extremely short, only the PEG block is crystallizable. With further increase in the length of the PCL block, both blocks can crystallize. The PCL crystallizes prior to the PEG block and has a stronger suppression effect on crystallization of the PEG block, while the PEG block only exerts a relatively weak adverse effect on crystallization of the PCL block. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

A comparative study of poly(l‐lactide)‐block‐poly(ϵ‐caprolactone) six‐armed star diblock copolymers and polylactide/poly(ϵ‐caprolactone) blends

This paper deals with the synthesis of a series of six‐armed star diblock copolymers based on poly(l ‐lactide) (PLLA) and poly(?‐caprolactone) (PCL) by ring‐opening polymerization using stannous octoate as catalyst and the preparation of polylactide (PLA)/PCL linear blends using a solution blending technique, while keeping the PLA‐to‐PCL ratio comparable in both systems. The thermal, rheological and mechanical properties of the copolymers and the blends were comparatively studied. The melting point and the degree of crystallinity were found to be lower for the copolymers than the blends due to poor folding property of star copolymers. Dynamic rheology revealed that the star polymers have lower elastic modulus, storage modulus and viscosity as compared to the corresponding blends with similar composition. The blends show two‐phase dispersed morphology whereas the copolymers exhibited microphase separated morphology with elongated (worm‐like) microdomains. The crystalline structures of the copolymers were characterized by larger crystallites than their blend counterparts, as estimated using Sherrer's equation based on wide‐angle X‐ray diffraction data. © 2016 Society of Chemical Industry     

Effect of molecular weight on spherulitic growth rate of poly(ϵ‐caprolactone) and poly(ϵ‐caprolactone)‐b‐poly(ethylene glycol)

The spherulitic growth rates of a series poly (?‐caprolactone) homopolymers and poly(?‐caprolactone)‐b‐ poly(ethylene glycol) (PCL‐b‐PEG) block copolymers with different molecular weights but narrow polydispersity were studied. The results show that for both PCL homopolymers and PCL‐b‐PEG block copolymers, the spherulitic growth rate first increases with molecular weight and reaches a maximum, then decreases as molecular weight increases. Crystallization temperature has greater influence on the spherulitic growth rate of polymers with higher molecular weight. Hoffman–Lauritzen theory was used to analyze spherulitic growth kinetics and the free energy of the folding surface (σ_e) was derived. It is found that the values of σ_e decrease with molecular weight at low molecular weight level and become constant for high molecular weight polymers. The chemically linked PEG block does not change the values of σ_e significantly. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

Novel biodegradable amphiphilic poly(ε‐caprolactone)/poly(N‐vinylpyrrolidone) blends via successive in situ polymerizations

In this study, biodegradable blends of poly(ε‐caprolactone) (PCL) and poly(N‐vinylpyrrolidone) (PVP) were prepared by a new strategy in the following steps: (1) free radical polymerization of N‐vinyl‐2‐pyrrolidone (NVP) in ε‐caprolactone (CL); (2) ring‐opening polymerization of ε‐caprolactone in the presence of PVP to obtain the target blends. The structure of the blends was confirmed by FTIR and ¹H NMR, and the molecular weight of PCL and PVP were determined by GPC. SEM study revealed that this polymerization method could decrease the disperse phase size and improve the interphase when compared with solution‐blending method. The phase inversion occurred when PVP content was 15–20 wt %. Subsequently, the PCL sphere dispersed in PVP matrix and its size decreased with the increase of PVP content. The contact angle results showed that PVP has a profound effect on hydrophilic properties of PCL/PVP blends. PCL/PVP blends are believed to be promising for drug delivery, cell therapy, and other biomedical applications. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Synthesis,characterization and biocompatibility of novel biodegradable poly[((R)‐3‐hydroxybutyrate)‐block‐(D,L‐lactide)‐block‐(ε‐caprolactone)] triblock copolymers

BACKGROUND: Biodegradable block copolymers have attracted particular attention in both fundamental and applied research because of their unique chain architecture, biodegradability and biocompatibility. Hence, biodegradable poly[((R )‐3 ‐hydroxybutyrate)‐block‐(D ,L ‐lactide)‐block‐(ε‐caprolactone)] (PHB‐PLA‐PCL) triblock copolymers were synthesized, characterized and evaluated for their biocompatibility. RESULTS: The results from nuclear magnetic resonance spectroscopy, gel permeation chromatography and thermogravimetric analysis showed that the novel triblock copolymers were successfully synthesized. Differential scanning calorimetry and wide‐angle X‐ray diffraction showed that the crystallinity of PHB in the copolymers decreased compared with methyl‐PHB (LMPHB) oligomer precursor. Blood compatibility experiments showed that the blood coagulation time became longer accompanied by a reduced number of platelets adhering to films of the copolymers with decreasing PHB content in the triblocks. Murine osteoblast MC3T3‐E1 cells cultured on the triblock copolymer films spread and proliferated significantly better compared with their growth on homopolymers of PHB, PLA and PCL, respectively. CONCLUSION: For the first time, PHB‐PLA‐PCL triblock copolymers were synthesized using low molecular weight LMPHB oligomer as the macroinitiator through ring‐opening polymerization with D ,L ‐lactide and ε‐caprolactone. The triblock copolymers exhibited flexible properties with good biocompatibility; they could be developed into promising biomedical materials for in vivo applications. Copyright © 2008 Society of Chemical Industry     

Study of a new titanium dual initiator for the synthesis of poly(ε‐caprolactone)‐b‐polystyrene block copolymers by the combination of coordination and nitroxide mediated polymerizations

Poly ε‐caprolactone‐polystyrene block‐copolymers (PCL‐b‐PSt) were synthesized using a modified titanium catalyst as the dual initiator. Alcoholysis of Ti(OPr)₄ by 4‐hydroxy 2,2,6,6 tetramethyl piperidinyl‐1‐oxyl (HO‐TEMPO) gave a bifunctional initiator Ti(OTEMPO)₄. Poly ε‐caprolactone prepolymer end‐capped with the nitroxide group was first prepared by ring opening polymerization of ε‐caprolactone with this initiator at high conversion. The nitroxide‐end‐capped structure and molar mass (M_n) of the polymers were demonstrated by typical UV absorption band. This analytical technique indicates a near‐quantitative nitroxide functionality and a M_n in good agreement with size exclusion chromatography (SEC) ones. This polyester prepolymer was used to further initiate the radical polymerization with styrene and reach the block copolymers (PCL‐b‐PSt). All the prepolymers and block copolymers were characterized by SEC and NMR spectroscopy. Additionally, the preparation of star polymers bearing two kinds of arms (PCL and PSt) was envisaged and a preliminary result was given. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Crystallization kinetics of thermosetting polymer blends of poly(ε‐caprolactone) and unsaturated polyester resin

A study has been made of the isothermal crystallization kinetics of poly(ε‐caprolactone) (PCL) in partially miscible crosslinked polyester resin (PER)/PCL blends by using differential scanning calorimetry (DSC). For comparison, miscible blends of PCL with uncured polyester resin, i.e., oligoester resin (OER), were also investigated. The overall crystallization rate of PCL remarkably decreased with the addition of amorphous component, OER or PER. The kinetic rate constant K_n decreased sharply for both the OER/PCL blends and the crosslinked PER/PCL blends with decreasing PCL concentration. The mechanism of nucleation and geometry of the growing PCL crystals was not remarkably affected by the incorporation of OER, but changed considerably with the addition of PER. However, the overall crystallization rate of PCL in the crosslinked PER/PCL blends was much higher compared with the corresponding uncured OER/PCL blends, which is attributable to the phase‐separated structure and the reduced miscibility in the crosslinked blends. According to the nucleation and growth theories, the nucleation process was considered to be the rate controlling step in the crystallization. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 74: 322–327, 1999     

Crystallization,morphology, and mechanical behavior of polylactide/poly(ε‐caprolactone) blends

Optically pure polylactides, poly(L ‐lactide) (PLLA) and poly(D ‐lactide) (PDLA), were blended across the range of compositions with poly(ε‐caprolactone) (PCL) to study their crystallization, morphology, and mechanical behavior. Differential scanning calorimetry and dynamic mechanical analysis (DMA) of the PLA/PCL blends showed two T_gs at positions close to the pure components revealing phase separation. However, a shift in the tan δ peak position by DMA from 64 to 57°C suggests a partial solubility of PCL in the PLA‐rich phase. Scanning electron microscopy reveals phase separation and a transition in the phase morphology from spherical to interconnected domains as the equimolar blend approaches from the outermost compositions. The spherulitic growth of both PLA and PCL in the blends was followed by polarized optical microscopy at 140 and 37°C. From tensile tests at speed of 50 mm/min Young's modulus values between 5.2 and 0.4 GPa, strength values between 56 and 12 MPa, and strain at break values between 1 and 400% were obtained varying the blend composition. The viscoelastic properties (E′ and tan δ) obtained at frequency of 1 Hz by DMA are discussed and are found consistent with composition, phase separation, and crystallization behavior of the blends. POLYM. ENG. SCI., 46:1299–1308, 2006. © 2006 Society of Plastics Engineers     

Crystallization,melting behavior,and wettability of poly(ε‐caprolactone) and poly(ε‐caprolactone)/ poly(N‐vinylpyrrolidone) blends

Both wettability and crystallizability control poly(ε‐caprolactone)'s (PCL) further applications as biomaterial. The wettability is an important property that is governed by both chemical composition and surface structure. In this study, we prepared the PCL/poly(N‐vinylpyrrolidone) (PVP) blends via successive in situ polymerization steps aiming for improving the wettability and decreasing crystallizability of PCL. The isothermal crystallization of PCL/PVP at different PVP concentrations was carried out. The equilibrium melting point (T), crystallization rate, and the melting behavior after isothermal crystallization were investigated using differential scanning calorimetry (DSC). The Avrami equation was used to fit the isothermal crystallization. The DSC results showed that PVP had restraining effect on the crystallizability of PCL, and the crystallization rate of PCL decreased clearly with the increase of PVP content in the blends. The X‐ray diffraction analysis (WAXD) results agreed with that. Water absorptivity and contact angle tests showed that the hydrophilic properties were improved with the increasing content of PVP in blends. The coefficient for the water diffusion into PCL/PVP blends showed to be non‐Fickian in character. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Biodegradable poly(vinyl alcohol)‐graft‐ poly(ε‐caprolactone) comb‐like polyester: Microwave synthesis and its characterization

Poly(vinyl alcohol)‐initiated microwave‐assisted ring opening polymerization of ε‐caprolactone in bulk was investigated, and a series of poly(vinyl alcohol)‐graft‐poly(ε‐caprolactone) (PVA‐g‐PCL) copolymers were prepared, with the degree of polymerization (DP) of PCL side chains and the degree of substitution (DS) of PVA by PCL being in the range of 3–24 and 0.35–0.89, respectively. The resultant comb‐like PVA‐g‐PCL copolymers were confirmed by means of FTIR, ¹H NMR, and viscometry measurement. The introduction of hydrophilic backbone resulted in the decrease in both melting point and crystallization property of the PVA‐g‐PCL copolymers comparing with linear PCL. With higher microwave power, the DP of PCL side chains and DS of PVA backbone were higher, and the polymerization reaction proceeded more rapidly. Both the DP and monomer conversion increased with irradiation time, while the DS increased first and then remained constant. With initiator in low concentration, the DP and DS were higher, while the monomer was converted more slowly. Microwaves dramatically improved the polymerization reaction in comparison of conventional heating method. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 104, 3973–3979, 2007     

Isothermal crystallization kinetics in binary miscible blend of poly(ε‐caprolactone)/tetramethyl polycarbonate

The crystallization kinetics of pure poly(ε‐caprolactone) (PCL) and its blends with bisphenol‐A tetramethyl polycarbonate (TMPC) was investigated isothermally as a function of composition and crystallization temperature (T_c) using differential scanning calorimetric (DSC) and polarized optical microscope techniques. Only a single glass‐transition temperature, T_g, was determined for each mixture indicating that this binary blend is miscible over the entire range of composition. The composition dependence of the T_g for this blend was well described by Gordon–Taylor equation with k = 1.8 (higher than unity) indicating strong intermolecular interaction between the two polymer components. The presence of a high T_g amorphous component (TMPC) had a strong influence on the crystallization kinetics of PCL in the blends. A substantial decrease in the crystallization kinetics was observed as the concentration of TMPC rose in the blends. The crystallization half‐time t_0.5 increased monotonically with the crystallization temperature for all composition. At any crystallization temperature (T_c) the t_0.5 of the blends are longer than the corresponding value for pure PCL. This behavior was attributed to the favorable thermodynamics interaction between PCL and TMPC which in turn led to a depression in the equilibrium melting point along with a simultaneous retardation in the crystallization of PC. The isothermal crystallization kinetics was analyzed on the basis of the Avrami equation. Linear behavior was held true for the augmentation of the radii of spherulites with time for all mixtures, regardless of the blend composition. However, the spherulites growth rate decreased exponentially with increasing the concentration of TMPC in the blends. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 103: 3307–3315, 2007